Microchip Technology

MCP6009-E/ST - 1 MHz Low-Power Quad Op Amp | Microchip

MPN: MCP6009-E/ST ✓ Active
1.8 V to 5.5 V Vdss 1 pA typical Id 14-pin TSSOP Package
MOQ: 1 |

MCP6009-E/ST Overview

The Microchip Technology MCP6009-E/ST is a general-purpose, quad operational amplifier with a 1 MHz typical gain-bandwidth product, rail-to-rail input and output operation, and a 1.8 V to 5.5 V single-supply operating range. The device is packaged in a 14-pin TSSOP and provides four amplifiers in one package, making it suitable for compact analog signal-conditioning and measurement systems.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Within the power-management and signal-processing hierarchy, this quad low-voltage operational amplifier belongs to the general-purpose amplifier family. Rail-to-rail input operation allows the input common-mode voltage to extend close to the supply rails, while rail-to-rail output operation improves output-voltage range. The MCP6009 family is unity-gain stable, supporting use as a voltage follower as well as in closed-loop amplifier configurations.

The MCP6009-E/ST features low input bias current, an input offset voltage of 1.6 mV maximum, 22 nV/√Hz input-voltage noise at 10 kHz, and 76 dB of EMI filtering and RF suppression. Its typical gain-bandwidth product is 1 MHz, while the listed slew rate is 1.9 V/µs. Each amplifier draws approximately 50 µA of supply current, and the complete 14-pin device is specified for operation from -40°C to +125°C.

The low-noise, low-power design combines analog signal conditioning with integrated EMI filtering. This makes the amplifier useful when low-level sensor signals must be amplified near noisy digital, switching, or RF-producing circuitry. A 1 MHz gain-bandwidth product is suitable for low-frequency instrumentation, buffering, and general signal-processing tasks, but it is not intended for high-speed video, high-resolution data acquisition above its bandwidth limits, or demanding precision applications where lower offset and noise are required.

Typical applications include battery-powered sensor interfaces, industrial measurement modules, portable medical equipment, audio preamplification, transducer conditioning, and low-voltage control systems. The quad configuration reduces board area by placing four amplifiers in one 14-pin TSSOP. Each amplifier can implement filtering, gain, summing, differential sensing, active filtering, or voltage-following functions, provided the selected gain and phase margin are compatible with the 1 MHz bandwidth.

Designers should place input and output decoupling capacitors close to the supply pins, route sensitive input traces away from switching nodes, and verify common-mode, output-swing, stability, and noise performance across the complete operating range. The EMI-filtering characteristic helps reduce high-frequency interference, but it does not remove the need for sound grounding and layout practices. Confirm the exact pin functions and exposed package details against the Microchip MCP6006/6R/6U/7/9 data sheet before laying out a PCB.

This product page combines the manufacturer specification summary, package and lifecycle information, engineering application guidance, structured comparison fields, and verified drop-in replacement research. The alternatives section includes only candidates for which a same-package relationship can be substantiated, avoiding cross-package substitutions that would require PCB changes.

Drop-in alternatives for MCP6009-E/ST — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

MCP6009T-E/ST

✅ Drop-In
📦 14-pin TSSOP
Same 14-pin TSSOP and 1 MHz quad-amplifier rating; order-code packaging or qualification differences require confirmation

📋 Reference alternative (not in catalog)

MCP6009-E/ST Maximum Ratings & Electrical Characteristics

Number of Amplifiers 4 amplifiers
Amplifier Type General-purpose operational amplifier
Gain-Bandwidth Product 1 MHz typical
Supply Voltage Range 1.8 V to 5.5 V
Rail-to-Rail Input Yes
Rail-to-Rail Output Yes
Unity-Gain Stable Yes
Input Offset Voltage ±1.6 mV maximum
Input Bias Current 1 pA typical
Input Offset Current 1 pA typical
Input Voltage Noise 22 nV/√Hz at 10 kHz
Slew Rate 1.9 V/µs typical
Quiescent Current 50 µA typical per amplifier
Output Current 30 mA typical
Operating Temperature Range -40°C to +125°C
EMI Filtering 76 dB EMI filtering/RF suppression
Temperature Drift 600 nV/°C
Package 14-pin TSSOP
Mounting Type Surface mount
RoHS Status Compliant

MCP6009-E/ST Pin Configuration

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pin 1 OUTA — Channel A output
Pin 2 IN A- — Channel A inverting input
Pin 3 IN A+ — Channel A non-inverting input
Pin 4 V+ — Positive supply voltage
Pin 5 IN B+ — Channel B non-inverting input
Pin 6 IN B- — Channel B inverting input
Pin 7 OUTB — Channel B output
Pin 8 OUTC — Channel C output
Pin 9 IN C- — Channel C inverting input
Pin 10 IN C+ — Channel C non-inverting input
Pin 11 V- — Negative supply voltage or ground connection
Pin 12 IN D+ — Channel D non-inverting input
Pin 13 IN D- — Channel D inverting input
Pin 14 OUTD — Channel D output

Typical Applications

MCP6009-E/ST is suitable for 6 applications: Battery-Powered Sensor Conditioning, Industrial Measurement Front Ends, Portable Medical Monitoring, Audio Preamplification, Transducer Signal Buffering, Low-Voltage Control Systems.

🧩

Battery-Powered Sensor Conditioning

The MCP6009-E/ST is well suited to conditioning weak sensor signals in battery-powered equipment because each amplifier operates from 1.8 V to 5.5 V and draws approximately 50 µA of quiescent current per channel. Its rail-to-rail input and output operation preserves usable signal range in compact, low-voltage systems. Designers can use the four amplifiers for sensor amplification, offset correction, filtering, and output buffering. The 1 MHz gain-bandwidth product supports low-frequency sensors, while the 1 pA typical input bias current benefits high-impedance sources. Stable operation at low gain and the integrated 76 dB EMI filtering and RF suppression also help when the sensor is near digital or switching circuitry.

🏭

Industrial Measurement Front Ends

The MCP6009-E/ST provides four channels of general-purpose amplification for industrial measurement systems requiring low supply voltage and compact analog conditioning. According to the Microchip manufacturer data sheet, the device has a 1 MHz typical gain-bandwidth product, ±1.6 mV maximum input offset, and rail-to-rail input/output operation. These characteristics fit low-level pressure, temperature, and position interfaces when their bandwidth requirements remain well below 1 MHz. The 14-pin TSSOP reduces board area compared with four separate amplifiers, while the -40°C to +125°C rating supports a broad range of industrial environments. Grounding and EMI control remain essential around long sensor cables.

💊

Portable Medical Monitoring

The MCP6009-E/ST can provide low-power analog conditioning in portable medical-monitoring equipment operating from a 1.8 V to 5.5 V source. According to the Microchip manufacturer data sheet, the low 50 µA typical quiescent current per amplifier helps limit battery consumption, while four amplifiers in one package provide amplification, buffering, and active filtering functions. Rail-to-rail input and output operation can improve signal utilization within a restricted supply range. The 1 MHz bandwidth is appropriate for many low-frequency physiological sensors but should not be assumed adequate for higher-bandwidth diagnostic signals. Medical designs must also evaluate application-specific safety, accuracy, and isolation requirements.

🎧

Audio Preamplification

The MCP6009-E/ST is suitable for modest audio preamplification, line-level buffering, and active filtering because it combines four rail-to-rail input/output amplifiers with a 1 MHz gain-bandwidth product. According to the Microchip manufacturer data sheet, the device has 22 nV/√Hz input-voltage noise at 10 kHz and integrated EMI filtering. These characteristics can support low-impedance microphone or line inputs when the required bandwidth is below the amplifier's capability and the input source impedance is appropriate. The 1.9 V/µs typical slew rate helps with small-signal waveform reproduction. Designers should verify output headroom, load impedance, distortion, and stability at the selected closed-loop gain.

📡

Transducer Signal Buffering

The MCP6009-E/ST can buffer high-impedance transducers when the source requires low input current and the signal bandwidth is modest. According to the Microchip product information, the amplifier family provides 1 pA typical input bias current, rail-to-rail input operation, and a 1 MHz typical gain-bandwidth product. The four channels can implement source buffering, differential amplification, gain stages, and active filters. Its low 50 µA typical quiescent current per amplifier also suits compact instrumentation. Source capacitance, noise gain, output loading, and common-mode limits must be evaluated because a unity-gain-stable device still requires suitable passive compensation and stable operating conditions.

⚡

Low-Voltage Control Systems

The MCP6009-E/ST is applicable to low-voltage control and monitoring circuits that require four op amps in a compact package. According to the Microchip manufacturer data sheet, it operates from 1.8 V to 5.5 V, provides rail-to-rail input/output behavior, and is unity-gain stable. The four channels can implement error amplifiers, comparators with hysteresis, current-to-voltage conversion, active filtering, and actuator-signal conditioning. The approximately 50 µA per-amplifier quiescent current reduces the supply burden in embedded systems, while the 14-pin TSSOP supports surface-mount assembly. Timing and output-current requirements should be checked against the 1 MHz bandwidth and 30 mA typical output-current specification.

What is the operating voltage range of MCP6009-E/ST?
The MCP6009-E/ST operates from 1.8 V to 5.5 V with a single supply. According to the Microchip MCP6006/6R/6U/7/9 manufacturer datasheet, the family supports low-voltage operation while maintaining rail-to-rail input and output behavior. Confirm absolute maximum voltage and supply sequencing requirements in the datasheet before applying the device outside its specified operating range.
What are the key specifications of MCP6009-E/ST that engineers should know?
The MCP6009-E/ST combines four unity-gain-stable amplifiers in a 14-pin TSSOP. According to the Microchip manufacturer datasheet and product information, key specifications include a 1 MHz typical gain-bandwidth product, 1.8 V to 5.5 V supply operation, ±1.6 mV maximum input offset, 1 pA typical input bias current, 22 nV/√Hz input noise at 10 kHz, and 1.9 V/µs typical slew rate.
Is MCP6009-E/ST rail-to-rail input and output?
Yes, the MCP6009-E/ST supports rail-to-rail input and output operation. According to the Microchip product page, this allows the input common-mode and output voltage ranges to extend toward the supply rails. The exact usable common-mode and output-swing limits depend on supply voltage and load, so use the manufacturer data-sheet curves rather than assuming full rail-to-rail movement under every condition.
Where can I download the MCP6009-E/ST datasheet PDF?
The manufacturer MCP6006/6R/6U/7/9 data sheet is available directly from Microchip at the official PDF link listed on this page. It covers the MCP6009 family, including electrical characteristics, pin descriptions, typical application circuits, and package information. The document identifier shown by the manufacturer is 20006411B; use the revision associated with the Microchip product page when checking production documentation.
Where can I find the MCP6009-E/ST pinout?
The MCP6009-E/ST uses a 14-pin TSSOP with four complete operational-amplifier channels. According to the Microchip manufacturer data sheet, pins 1 through 7 implement channels A and B, pins 8 through 11 implement channel C and the negative supply connection, and pins 12 through 14 complete channel D and the positive supply connection. Use the pin-description table for the authoritative orientation.
What can replace MCP6009-E/ST on the same PCB?
A valid PCB replacement must use the same 14-pin TSSOP footprint and preserve the four-amplifier pin arrangement. The MCP6009T-E/ST is the only directly identified candidate in the substitution results, and its exact order-code characteristics should be checked before approval. No verified cross-brand drop-in candidates were identified, so a generic quad amplifier should not be treated as pin-compatible without a documented comparison.
Is MCP6009-E/ST suitable for low-voltage sensor interfaces?
The MCP6009-E/ST is suitable for many low-voltage sensor interfaces because it operates from 1.8 V to 5.5 V and provides rail-to-rail input and output operation. According to the Microchip manufacturer data sheet, its 1 pA typical input bias current is useful with high-impedance sources. Signal bandwidth, source impedance, settling time, and input offset must still be checked against the sensor output.
What can I use instead of MCP6009-E/ST?
MCP6009T-E/ST is the closest identified same-package alternative, with a 14-pin TSSOP configuration and the same 1 MHz general-purpose quad-amplifier family. According to the Microchip product information, both devices are rail-to-rail input/output amplifiers operating from 1.8 V to 5.5 V. Confirm the order-code temperature, tape-and-reel, and qualification differences before treating it as a drop-in replacement.
Where to buy MCP6009-E/ST online?
Use the Request a Quote form on this page to request MCP6009-E/ST availability, current commercial terms, and the required quantity and package variant. The form provides a direct route for stock, lead-time, and volume-price requests without embedding a static price that may change. Specify the exact MCP6009-E/ST order code and confirm the 14-pin TSSOP packaging requirement in the request.
What is the price of MCP6009-E/ST?
Current commercial pricing for MCP6009-E/ST should be obtained through the Request a Quote form on this page. Pricing can vary with order quantity, inventory, and requested packaging configuration, and a static figure may become obsolete quickly. Include your production quantity, target date, and whether you need the 14-pin TSSOP option in the quote request.
What is the lead time and stock status for MCP6009-E/ST?
Request the current MCP6009-E/ST stock position and lead time through the Request a Quote form on this page. Lead time can vary with order size, allocation, and packaging requirements, so it should be confirmed for the exact order code. The form is the appropriate route for current schedule and minimum-order information.
MCP6009-E/ST vs MCP6009T-E/ST — which one should I choose?
Both devices are identified as 14-pin TSSOP quad operational amplifiers with 1 MHz bandwidth and 1.8 V to 5.5 V supply operation. According to Microchip product information, the distinguishing information lies in the order code and associated packaging or qualification details. Compare those suffixes, temperature requirements, reel configuration, and qualification needs before selecting the production part number.
When should I choose MCP6009-E/ST instead of a higher-bandwidth op amp?
Choose MCP6009-E/ST when the signal bandwidth is comfortably below its 1 MHz typical gain-bandwidth product and low power consumption is important. According to the Microchip manufacturer data sheet, the family provides approximately 50 µA typical quiescent current per amplifier. Use a higher-bandwidth or lower-offset amplifier when the signal requires faster settling, greater precision, or more output drive than this device provides.
Is MCP6009-E/ST the same as MCP6009T-E/ST?
No, MCP6009-E/ST and MCP6009T-E/ST are distinct Microchip order codes, although both are identified as 14-pin TSSOP, 1 MHz, quad rail-to-rail operational amplifiers. According to the manufacturer listings, their key functionality is closely aligned, but suffix differences can affect packaging or qualification. Confirm each code's complete ordering information before treating the parts as interchangeable.
Does MCP6009-E/ST include EMI filtering?
Yes, the MCP6009 family includes EMI filtering and RF suppression, with a listed rejection figure of 76 dB. According to the Microchip manufacturer data sheet and product information, this feature helps attenuate high-frequency interference coupled into sensitive amplifier inputs. It improves robustness but does not replace short input traces, proper grounding, filtering, and isolation from switching nodes.
What is the best Microchip equivalent for MCP6009-E/ST?
MCP6009T-E/ST is the best directly identified Microchip-family candidate for MCP6009-E/ST because it uses the same 14-pin TSSOP format and closely aligned 1 MHz quad-amplifier specifications. According to the Microchip product information, both provide rail-to-rail input/output operation from a 1.8 V to 5.5 V supply. Review the order-code and qualification details before approving it as a drop-in part.

Engineering reference data for MCP6009-E/ST — comparison, design guidance, and compliance information.

Selection Guide

Choose MCP6009-E/ST when a compact system needs four general-purpose amplifiers operating from 1.8 V to 5.5 V, especially with sensor, buffering, filtering, or control functions below the 1 MHz bandwidth limit. Its rail-to-rail input/output operation, 1 pA typical input bias current, low per-channel quiescent current, and integrated EMI filtering make it suitable for low-power instrumentation. MCP6009T-E/ST is the closest identified same-package alternative and can be considered when its order-code packaging or qualification details satisfy the production requirement. Do not substitute a generic quad op amp solely because it also has a 14-pin TSSOP package; verify pin mapping, common-mode range, output swing, stability, offset, bias current, noise, slew rate, and EMI behavior. For signals requiring substantially more bandwidth, lower offset, faster settling, higher output current, or different supply limits, choose an amplifier explicitly specified for those requirements.

Comparison with Alternatives

Parameter This Product MCP6009T-E/ST
Package 14-pin TSSOP 14-pin TSSOP
Brand Microchip Technology Microchip Technology
Number of Amplifiers 4 4
Gain-Bandwidth Product 1 MHz typical 1 MHz typical
Supply Voltage Range 1.8 V to 5.5 V 1.8 V to 5.5 V
Rail-to-Rail Input Yes Yes
Rail-to-Rail Output Yes Yes

Key Differentiators

  • Four low-power amplifiers in one package (vs MCP6009T-E/ST)
  • Rail-to-rail operation over a low-voltage supply range (vs MCP6009T-E/ST)
  • Integrated EMI filtering and RF suppression (vs MCP6009T-E/ST)

Design Notes

Route each inverting-input feedback trace directly between the amplifier output and its inverting-input pin, and keep the non-inverting input away from supply, clock, and switching traces. The MCP6009 family includes 76 dB EMI filtering and RF suppression, but that feature cannot compensate for a long antenna-like input route. Use a continuous ground plane and place the positive and negative supply bypass capacitors close to their respective pins.

Do not treat rail-to-rail input and output as unlimited. Verify the allowable input common-mode range and output swing across supply voltage, temperature, output frequency, and load. For stability, include the recommended source and feedback impedances and compensation shown in the manufacturer data sheet. The device is unity-gain stable, but noise gain and load capacitance can still affect closed-loop behavior.

Estimated: four amplifiers at 50 µA typical each draw approximately 200 µA of quiescent supply current before load current is included. This estimate uses the 50 µA per-amplifier typical value and does not include input bias current, output-current demand, leakage, or power-supply tolerance. Add the calculated worst-case supply current to the load budget when sizing a low-power rail.

For sensor interfaces, minimize input-node capacitance and keep sensitive traces short to reduce noise gain and sensitivity to injected RF energy. Place passive anti-alias or anti-interference components close to the input when their filtering requirements are known. A common-mode or differential filter should be validated against the intended signal bandwidth rather than selected solely from the amplifier's 1 MHz gain-bandwidth product.

Compliance Information

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The JLCPCB component listing identifies the MCP6009-E/ST as RoHS compliant. No specific REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the available manufacturer and distributor information.

Related Searches

mcp6009 datasheet MCP6009-E/ST datasheet MCP6009-E/ST datasheet pdf MCP6009-E/ST pinout MCP6009-E/ST TSSOP-14 MCP6009-E/ST equivalent MCP6009-E/ST replacement MCP6009-E/ST cross reference MCP6009-E/ST vs MCP6009T-E/ST Microchip MCP6009-E/ST MCP6009-E/ST 1 MHz op amp MCP6009-E/ST price MCP6009-E/ST stock MCP6009 rail to rail input output MCP6009 low voltage sensor amplifier

Related Components & Terms

Microchip Technology MCP6009-E/ST MCP6009T-E/ST MCP6006/6R/6U/7/9 quad operational amplifier general-purpose amplifier signal-conditioning amplifier analog amplifier semiconductor 1 MHz gain-bandwidth product rail-to-rail input rail-to-rail output unity-gain stable input bias current input offset voltage input-voltage noise EMI filtering RF suppression TSSOP-14 TSSOP package family surface-mount package battery-powered instrumentation industrial measurement medical monitoring
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details