MCP6009-E/ST - 1 MHz Low-Power Quad Op Amp | Microchip
MPN: MCP6009-E/ST ✓ NakahandaMCP6009-E/ST Ulas
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Within the power-management and signal-processing hierarchy, this quad low-voltage operational amplifier belongs to the general-purpose amplifier family. Rail-to-rail input operation allows the input common-mode voltage to extend close to the supply rails, while rail-to-rail output operation improves output-voltage range. The MCP6009 family is unity-gain stable, supporting use as a voltage follower as well as in closed-loop amplifier configurations.
The MCP6009-E/ST features low input bias current, an input offset voltage of 1.6 mV maximum, 22 nV/√Hz input-voltage noise at 10 kHz, and 76 dB of EMI filtering and RF suppression. Its typical gain-bandwidth product is 1 MHz, while the listed slew rate is 1.9 V/µs. Each amplifier draws approximately 50 µA of supply current, and the complete 14-pin device is specified for operation from -40°C to +125°C.
The low-noise, low-power design combines analog signal conditioning with integrated EMI filtering. This makes the amplifier useful when low-level sensor signals must be amplified near noisy digital, switching, or RF-producing circuitry. A 1 MHz gain-bandwidth product is suitable for low-frequency instrumentation, buffering, and general signal-processing tasks, but it is not intended for high-speed video, high-resolution data acquisition above its bandwidth limits, or demanding precision applications where lower offset and noise are required.
Typical applications include battery-powered sensor interfaces, industrial measurement modules, portable medical equipment, audio preamplification, transducer conditioning, and low-voltage control systems. The quad configuration reduces board area by placing four amplifiers in one 14-pin TSSOP. Each amplifier can implement filtering, gain, summing, differential sensing, active filtering, or voltage-following functions, provided the selected gain and phase margin are compatible with the 1 MHz bandwidth.
Designers should place input and output decoupling capacitors close to the supply pins, route sensitive input traces away from switching nodes, and verify common-mode, output-swing, stability, and noise performance across the complete operating range. The EMI-filtering characteristic helps reduce high-frequency interference, but it does not remove the need for sound grounding and layout practices. Confirm the exact pin functions and exposed package details against the Microchip MCP6006/6R/6U/7/9 data sheet before laying out a PCB.
This product page combines the manufacturer specification summary, package and lifecycle information, engineering application guidance, structured comparison fields, and verified drop-in replacement research. The alternatives section includes only candidates for which a same-package relationship can be substantiated, avoiding cross-package substitutions that would require PCB changes.
Mga alternatibo na pwedeng ilagay na MCP6009-E/ST — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
MCP6009T-E/ST
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MCP6009-E/ST Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Amplifiers | 4 amplifiers |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz typical |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Unity-Gain Stable | Yes |
| Input Offset Voltage | ±1.6 mV maximum |
| Input Bias Current | 1 pA typical |
| Input Offset Current | 1 pA typical |
| Input Voltage Noise | 22 nV/√Hz at 10 kHz |
| Slew Rate | 1.9 V/µs typical |
| Kuru-kuryente ng Kapayapaan | 50 µA typical per amplifier |
| Output Current | 30 mA typical |
| Hanay ng Temperature na Operasyon | -40°C to +125°C |
| EMI Filtering | 76 dB EMI filtering/RF suppression |
| Temperature Drift | 600 nV/°C |
| Packhaging | 14-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | Compliant |
Pin Configuration ng MCP6009-E/ST
| Pin 1 | OUTA — Channel A output |
| Pin 2 | IN A- — Channel A inverting input |
| Pin 3 | IN A+ — Channel A non-inverting input |
| Pin 4 | V+ — Positive supply voltage |
| Pin 5 | IN B+ — Channel B non-inverting input |
| Pin 6 | IN B- — Channel B inverting input |
| Pin 7 | OUTB — Channel B output |
| Pin 8 | OUTC — Channel C output |
| Pin 9 | IN C- — Channel C inverting input |
| Pin 10 | IN C+ — Channel C non-inverting input |
| Pin 11 | V- — Negative supply voltage or ground connection |
| Pin 12 | IN D+ — Channel D non-inverting input |
| Pin 13 | IN D- — Channel D inverting input |
| Pin 14 | OUTD — Channel D output |
Tipikal na mga Gamit
MCP6009-E/ST ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Conditioning, Industrial Measurement Front Ends, Portable Medical Monitoring, Audio Preamplification, Transducer Signal Buffering, Low-Voltage Control Systems.
Battery-Powered Sensor Conditioning
The MCP6009-E/ST is well suited to conditioning weak sensor signals in battery-powered equipment because each amplifier operates from 1.8 V to 5.5 V and draws approximately 50 µA of quiescent current per channel. Its rail-to-rail input and output operation preserves usable signal range in compact, low-voltage systems. Designers can use the four amplifiers for sensor amplification, offset correction, filtering, and output buffering. The 1 MHz gain-bandwidth product supports low-frequency sensors, while the 1 pA typical input bias current benefits high-impedance sources. Stable operation at low gain and the integrated 76 dB EMI filtering and RF suppression also help when the sensor is near digital or switching circuitry.
Inirekomenda
Industrial Measurement Front Ends
The MCP6009-E/ST provides four channels of general-purpose amplification for industrial measurement systems requiring low supply voltage and compact analog conditioning. According to the Microchip manufacturer data sheet, the device has a 1 MHz typical gain-bandwidth product, ±1.6 mV maximum input offset, and rail-to-rail input/output operation. These characteristics fit low-level pressure, temperature, and position interfaces when their bandwidth requirements remain well below 1 MHz. The 14-pin TSSOP reduces board area compared with four separate amplifiers, while the -40°C to +125°C rating supports a broad range of industrial environments. Grounding and EMI control remain essential around long sensor cables.
Inirekomenda
Portable Medical Monitoring
The MCP6009-E/ST can provide low-power analog conditioning in portable medical-monitoring equipment operating from a 1.8 V to 5.5 V source. According to the Microchip manufacturer data sheet, the low 50 µA typical quiescent current per amplifier helps limit battery consumption, while four amplifiers in one package provide amplification, buffering, and active filtering functions. Rail-to-rail input and output operation can improve signal utilization within a restricted supply range. The 1 MHz bandwidth is appropriate for many low-frequency physiological sensors but should not be assumed adequate for higher-bandwidth diagnostic signals. Medical designs must also evaluate application-specific safety, accuracy, and isolation requirements.
Inirekomenda
Audio Preamplification
The MCP6009-E/ST is suitable for modest audio preamplification, line-level buffering, and active filtering because it combines four rail-to-rail input/output amplifiers with a 1 MHz gain-bandwidth product. According to the Microchip manufacturer data sheet, the device has 22 nV/√Hz input-voltage noise at 10 kHz and integrated EMI filtering. These characteristics can support low-impedance microphone or line inputs when the required bandwidth is below the amplifier's capability and the input source impedance is appropriate. The 1.9 V/µs typical slew rate helps with small-signal waveform reproduction. Designers should verify output headroom, load impedance, distortion, and stability at the selected closed-loop gain.
Inirekomenda
Transducer Signal Buffering
The MCP6009-E/ST can buffer high-impedance transducers when the source requires low input current and the signal bandwidth is modest. According to the Microchip product information, the amplifier family provides 1 pA typical input bias current, rail-to-rail input operation, and a 1 MHz typical gain-bandwidth product. The four channels can implement source buffering, differential amplification, gain stages, and active filters. Its low 50 µA typical quiescent current per amplifier also suits compact instrumentation. Source capacitance, noise gain, output loading, and common-mode limits must be evaluated because a unity-gain-stable device still requires suitable passive compensation and stable operating conditions.
Inirekomenda
Low-Voltage Control Systems
The MCP6009-E/ST is applicable to low-voltage control and monitoring circuits that require four op amps in a compact package. According to the Microchip manufacturer data sheet, it operates from 1.8 V to 5.5 V, provides rail-to-rail input/output behavior, and is unity-gain stable. The four channels can implement error amplifiers, comparators with hysteresis, current-to-voltage conversion, active filtering, and actuator-signal conditioning. The approximately 50 µA per-amplifier quiescent current reduces the supply burden in embedded systems, while the 14-pin TSSOP supports surface-mount assembly. Timing and output-current requirements should be checked against the 1 MHz bandwidth and 30 mA typical output-current specification.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for MCP6009-E/ST — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MCP6009T-E/ST |
|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP |
| Brand | Microchip Technology | Microchip Technology |
| Number of Amplifiers | 4 | 4 |
| Gain-Bandwidth Product | 1 MHz typical | 1 MHz typical |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Rail-to-Rail Input | Yes | Yes |
| Rail-to-Rail Output | Yes | Yes |
Pangunahing mga Pagkakaiba
- Four low-power amplifiers in one package (kumpara saMCP6009T-E/ST)
- Rail-to-rail operation over a low-voltage supply range (kumpara saMCP6009T-E/ST)
- Integrated EMI filtering and RF suppression (kumpara saMCP6009T-E/ST)
Talaan ng Disenyo
Route each inverting-input feedback trace directly between the amplifier output and its inverting-input pin, and keep the non-inverting input away from supply, clock, and switching traces. The MCP6009 family includes 76 dB EMI filtering and RF suppression, but that feature cannot compensate for a long antenna-like input route. Use a continuous ground plane and place the positive and negative supply bypass capacitors close to their respective pins.
Do not treat rail-to-rail input and output as unlimited. Verify the allowable input common-mode range and output swing across supply voltage, temperature, output frequency, and load. For stability, include the recommended source and feedback impedances and compensation shown in the manufacturer data sheet. The device is unity-gain stable, but noise gain and load capacitance can still affect closed-loop behavior.
Estimated: four amplifiers at 50 µA typical each draw approximately 200 µA of quiescent supply current before load current is included. This estimate uses the 50 µA per-amplifier typical value and does not include input bias current, output-current demand, leakage, or power-supply tolerance. Add the calculated worst-case supply current to the load budget when sizing a low-power rail.
For sensor interfaces, minimize input-node capacitance and keep sensitive traces short to reduce noise gain and sensitivity to injected RF energy. Place passive anti-alias or anti-interference components close to the input when their filtering requirements are known. A common-mode or differential filter should be validated against the intended signal bandwidth rather than selected solely from the amplifier's 1 MHz gain-bandwidth product.
Impormasyon ng Pagsunod sa Kautusan
The JLCPCB component listing identifies the MCP6009-E/ST as RoHS compliant. No specific REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the available manufacturer and distributor information.