OPA705PA - 12V 1MHz Rail-to-Rail Op Amp | Texas Instruments
MPN: OPA705PA ✓ ActiveOPA705PA Overview
An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. The op-amp category belongs to the broader amplifier IC hierarchy, where it supports signal conditioning, feedback control, impedance conversion, and precision analog measurement. OPA705 is a CMOS, rail-to-Rail I/O amplifier: its input and output stages can operate close to the supply rails, which is useful in systems where conventional non-rail-to-rail amplifiers would clip or distort signals.
The OPA705 family combines a 1 MHz gain-bandwidth product with a typical slew rate of 0.6 V/µs. Its common-mode rejection is 96 dB, while low input bias current supports high-impedance sensing stages. The 160 µA quiescent current makes the device suitable for portable, battery-powered, and low-power instrumentation. The manufacturer also identifies low offset, low noise, and broad supply-voltage operation as key benefits of the family.
OPA705PA is the through-hole PDIP-8 ordering option of the single OPA705 amplifier. The same family is also offered in SOT23-5 and standard SO-8 surface-mount packages, while the dual OPA2705 family covers MSOP-8, SO-8, and DIP-8 configurations. Package selection therefore depends on whether the design prioritizes manual assembly and PCB prototyping, compact surface-mount area, or production volume.
Typical uses include sensor interfaces, low-frequency filter stages, buffer amplifiers, portable measurement equipment, and general analog signal chains. Designers should preserve adequate input and output headroom, check the required output current against the device limits, and verify the common-mode and output-swing conditions in the datasheet. Decoupling capacitors should be placed close to the supply pins to reduce supply impedance and improve transient response.
This page compares the OPA705PA with verified same-family and cross-reference candidates, summarizes the manufacturer specifications, and provides application-focused design guidance. It also distinguishes the PDIP-8 through-hole package from similarly specified surface-mount versions, helping engineers determine whether a candidate is truly pin-compatible before making a board-level substitution.
Drop-in alternatives for OPA705PA — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesOPA705PA Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Architecture | CMOS |
| Number of Circuits | 1 circuit |
| Nominal Supply Voltage | 12 V |
| Single-Supply Operating Range | 4 V to 12 V |
| Dual-Supply Operating Range | ±2 V to ±6 V |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Input Offset Voltage | 0.5 mV typical |
| Common-Mode Rejection Ratio | 96 dB |
| Quiescent Current | 160 µA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Package | 8-pin PDIP |
| Mounting Type | Through-hole |
| Application Class | General-purpose instrumentation and buffer amplifier |
OPA705PA 8-pin pdip Pin Configuration Guide
Pin configuration for OPA705PA (8-pin pdip package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for OPA705PA.
Refer to the datasheet for full pin configuration.
Typical Applications
OPA705PA is suitable for 6 applications: Portable Sensor Signal Conditioning, General-Purpose Instrumentation Buffer, Portable Medical Sensor Interface, Industrial Control Signal Amplification, Low-Power Voltage Buffer, Low-Frequency Active Filter Stage.
Portable Sensor Signal Conditioning
The OPA705PA fits low-power sensor front ends that require a rail-to-rail input and an amplifier with only 160 µA of quiescent current. Place the device in a non-inverting or inverting configuration close to the sensor to limit noise pickup and provide impedance buffering. Its 1 MHz gain-bandwidth product supports closed-loop gains below unity at low frequencies, while the 0.5 mV typical offset and 96 dB common-mode rejection help preserve small sensor signals. Because the amplifier is supplied from a single 4 V to 12 V rail, verify that the sensor signal remains inside the common-mode range and that the required output amplitude does not clip the rail-to-rail output limits.
Recommended
General-Purpose Instrumentation Buffer
OPA705PA is suitable for buffering instrument signals where high input impedance prevents the source from being loaded. Its low input bias current is valuable when driving the amplifier from a high-impedance sensor or resistive divider, and its 96 dB common-mode rejection reduces unwanted common-mode conversion. The 1 MHz gain-bandwidth product is appropriate for low-frequency measurement channels rather than wideband signal capture. In a unity-gain buffer, confirm output stability, capacitive-load limits, and available output current for the attached instrumentation or ADC input.
Recommended
Portable Medical Sensor Interface
The OPA705PA can support compact biomedical sensor interfaces when its electrical characteristics fit the sensing topology. Its low 160 µA quiescent current reduces the standing burden of battery-powered equipment, while rail-to-rail input operation helps retain signal range in low-voltage systems. Low offset and 96 dB common-mode rejection are useful for amplifying small differential signals near the center of the supply range. Medical designs must additionally verify applicable safety, leakage, isolation, qualification, and operating-temperature requirements; the amplifier itself does not establish compliance for the finished instrument.
Recommended
Industrial Control Signal Amplification
OPA705PA can amplify low-frequency control and diagnostic signals in industrial equipment operating from a single 4 V to 12 V supply. Its 1 MHz gain-bandwidth product provides useful closed-loop bandwidth for servo, conditioning, and status-detection stages, while the 0.6 V/µs slew rate determines large-signal response. The amplifier’s rail-to-rail I/O capability improves utilization of the available supply voltage. Designers should still account for industrial temperature limits, noise from switching power stages, grounding around the signal source, and the output drive required by the next circuit stage.
Recommended
Low-Power Voltage Buffer
OPA705PA can buffer a reference or low-current voltage node while drawing only 160 µA quiescent current in typical operation. Rail-to-rail input and output characteristics make it useful when the buffered level occupies much of the 4 V to 12 V supply range. The device’s 0.5 mV typical input offset can matter in precision divider applications, so resistor accuracy, input bias effects, and the resulting closed-loop error should be calculated. Confirm the load current and capacitive loading because the low-power design is intended primarily for modest drive requirements.
Recommended
Low-Frequency Active Filter Stage
OPA705PA is appropriate for active-filter stages operating at low or moderate frequencies because its 1 MHz gain-bandwidth product leaves bandwidth above the intended filter corner in many designs. The 0.6 V/µs slew rate helps preserve large-signal response when the stage operates with modest output amplitudes. Its rail-to-rail input and output behavior supports signal swings close to the supply rails, and 96 dB common-mode rejection can reduce disturbance coupled into the filter from surrounding circuitry. Component tolerances and amplifier open-loop gain must be included in the frequency-response calculation, and stability must be checked with the selected feedback and load configuration.
Recommended
Engineering reference data for OPA705PA — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP |
| Amplifier Type | Single operational amplifier |
| Architecture | CMOS |
| Nominal Supply Voltage | 12 V |
| Single-Supply Operating Range | 4 V to 12 V |
| Dual-Supply Operating Range | ±2 V to ±6 V |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Quiescent Current | 160 µA |
| Input Offset Voltage | 0.5 mV typical |
| Common-Mode Rejection Ratio | 96 dB |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
Design Notes
Place the OPA705PA close to the source and load to minimize parasitic pickup and feedback-loop delay. Connect the supply bypass capacitor directly between the V+ and V− pins, with a short ground return to the signal reference. Keep the input traces away from switching nodes and high-current return paths. Because this is an 8-pin PDIP package, provide adequate through-hole spacing and mechanical clearance for the socket or board.
Do not interpret the rail-to-rail designation as zero output resistance or unlimited output swing. Check the output voltage limits over the required supply range, temperature interval, and load current. Similarly, confirm that the sensor or source voltage remains within the common-mode range at startup and during transients. A single-supply circuit must also account for the ground reference when calculating the full-scale input range.
Use the 1 MHz gain-bandwidth product and 0.6 V/µs slew-rate figures to establish a practical bandwidth and rise-time limit for each gain stage. Check feedback-network impedance, capacitive loading, and noise gain because they can affect closed-loop response and stability. For sensor interfaces, favor a short, guarded input route and place any filtering resistor or capacitor directly at the amplifier input.
Calculate amplifier dissipation from the actual supply voltage, output voltage, and load current using the difference between input and output voltage multiplied by output current. The 160 µA figure describes quiescent current and does not include load-dependent output current. Ensure the 12 V maximum operating condition, package temperature rise, and adjacent component tolerances remain acceptable under worst-case supply and load.
Compliance Information
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the verified product information. Confirm current compliance documents from Texas Instruments before procurement.