Texas Instruments

OPA705PA - 12V 1MHz Rail-to-Rail Op Amp | Texas Instruments

부품 번호: OPA705PA ✓ 활성
12 V Vdss 160 µA Id 8-pin PDIP Package
MOQ: 1 |

OPA705PA 개요

Texas Instruments OPA705PA is a single, low-cost CMOS operational amplifier with a 12 V nominal supply, 1 MHz gain-bandwidth product, rail-to-rail input and output operation, and an 8-pin PDIP package. It is designed for general-purpose instrumentation, buffering, and low-power signal-conditioning applications. The amplifier operates from 4 V to 12 V on a single supply or from ±2 V to ±6 V on dual supplies, with low quiescent current of 160 µA and typical input offset voltage of 0.5 mV.

An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. The op-amp category belongs to the broader amplifier IC hierarchy, where it supports signal conditioning, feedback control, impedance conversion, and precision analog measurement. OPA705 is a CMOS, rail-to-Rail I/O amplifier: its input and output stages can operate close to the supply rails, which is useful in systems where conventional non-rail-to-rail amplifiers would clip or distort signals.

The OPA705 family combines a 1 MHz gain-bandwidth product with a typical slew rate of 0.6 V/µs. Its common-mode rejection is 96 dB, while low input bias current supports high-impedance sensing stages. The 160 µA quiescent current makes the device suitable for portable, battery-powered, and low-power instrumentation. The manufacturer also identifies low offset, low noise, and broad supply-voltage operation as key benefits of the family.

OPA705PA is the through-hole PDIP-8 ordering option of the single OPA705 amplifier. The same family is also offered in SOT23-5 and standard SO-8 surface-mount packages, while the dual OPA2705 family covers MSOP-8, SO-8, and DIP-8 configurations. Package selection therefore depends on whether the design prioritizes manual assembly and PCB prototyping, compact surface-mount area, or production volume.

Typical uses include sensor interfaces, low-frequency filter stages, buffer amplifiers, portable measurement equipment, and general analog signal chains. Designers should preserve adequate input and output headroom, check the required output current against the device limits, and verify the common-mode and output-swing conditions in the datasheet. Decoupling capacitors should be placed close to the supply pins to reduce supply impedance and improve transient response.

This page compares the OPA705PA with verified same-family and cross-reference candidates, summarizes the manufacturer specifications, and provides application-focused design guidance. It also distinguishes the PDIP-8 through-hole package from similarly specified surface-mount versions, helping engineers determine whether a candidate is truly pin-compatible before making a board-level substitution.

드롭인 대체품: OPA705PA — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

OPA705PA 최대 정격 & 전기적 특성

Amplifier Type Single operational amplifier
Architecture CMOS
Number of Circuits 1 circuit
Nominal Supply Voltage 12 V
Single-Supply Operating Range 4 V to 12 V
Dual-Supply Operating Range ±2 V to ±6 V
Gain-Bandwidth Product 1 MHz
Slew Rate 0.6 V/µs
Input Offset Voltage 0.5 mV typical
Common-Mode Rejection Ratio 96 dB
대기 전류 160 µA
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
패키지 8-pin PDIP
실장 유형 Through-hole
Application Class General-purpose instrumentation and buffer amplifier

OPA705PA 8-pin pdip 핀 구성 가이드

OPA705PA(8-pin pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

OPA705PA의 8-pin pdip 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: OPA705PA.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

OPA705PA 적합 용도: 6 애플리케이션s: Portable Sensor Signal Conditioning, General-Purpose Instrumentation Buffer, Portable Medical Sensor Interface, Industrial Control Signal Amplification, Low-Power Voltage Buffer, Low-Frequency Active Filter Stage.

🧩

Portable Sensor Signal Conditioning

The OPA705PA fits low-power sensor front ends that require a rail-to-rail input and an amplifier with only 160 µA of quiescent current. Place the device in a non-inverting or inverting configuration close to the sensor to limit noise pickup and provide impedance buffering. Its 1 MHz gain-bandwidth product supports closed-loop gains below unity at low frequencies, while the 0.5 mV typical offset and 96 dB common-mode rejection help preserve small sensor signals. Because the amplifier is supplied from a single 4 V to 12 V rail, verify that the sensor signal remains inside the common-mode range and that the required output amplitude does not clip the rail-to-rail output limits.

🔧

General-Purpose Instrumentation Buffer

OPA705PA is suitable for buffering instrument signals where high input impedance prevents the source from being loaded. Its low input bias current is valuable when driving the amplifier from a high-impedance sensor or resistive divider, and its 96 dB common-mode rejection reduces unwanted common-mode conversion. The 1 MHz gain-bandwidth product is appropriate for low-frequency measurement channels rather than wideband signal capture. In a unity-gain buffer, confirm output stability, capacitive-load limits, and available output current for the attached instrumentation or ADC input.

💊

Portable Medical Sensor Interface

The OPA705PA can support compact biomedical sensor interfaces when its electrical characteristics fit the sensing topology. Its low 160 µA quiescent current reduces the standing burden of battery-powered equipment, while rail-to-rail input operation helps retain signal range in low-voltage systems. Low offset and 96 dB common-mode rejection are useful for amplifying small differential signals near the center of the supply range. Medical designs must additionally verify applicable safety, leakage, isolation, qualification, and operating-temperature requirements; the amplifier itself does not establish compliance for the finished instrument.

🏭

Industrial Control Signal Amplification

OPA705PA can amplify low-frequency control and diagnostic signals in industrial equipment operating from a single 4 V to 12 V supply. Its 1 MHz gain-bandwidth product provides useful closed-loop bandwidth for servo, conditioning, and status-detection stages, while the 0.6 V/µs slew rate determines large-signal response. The amplifier’s rail-to-rail I/O capability improves utilization of the available supply voltage. Designers should still account for industrial temperature limits, noise from switching power stages, grounding around the signal source, and the output drive required by the next circuit stage.

⚡

Low-Power Voltage Buffer

OPA705PA can buffer a reference or low-current voltage node while drawing only 160 µA quiescent current in typical operation. Rail-to-rail input and output characteristics make it useful when the buffered level occupies much of the 4 V to 12 V supply range. The device’s 0.5 mV typical input offset can matter in precision divider applications, so resistor accuracy, input bias effects, and the resulting closed-loop error should be calculated. Confirm the load current and capacitive loading because the low-power design is intended primarily for modest drive requirements.

📡

Low-Frequency Active Filter Stage

OPA705PA is appropriate for active-filter stages operating at low or moderate frequencies because its 1 MHz gain-bandwidth product leaves bandwidth above the intended filter corner in many designs. The 0.6 V/µs slew rate helps preserve large-signal response when the stage operates with modest output amplitudes. Its rail-to-rail input and output behavior supports signal swings close to the supply rails, and 96 dB common-mode rejection can reduce disturbance coupled into the filter from surrounding circuitry. Component tolerances and amplifier open-loop gain must be included in the frequency-response calculation, and stability must be checked with the selected feedback and load configuration.

What is the operating voltage range of OPA705PA?
The OPA705PA operates from 4 V to 12 V on a single supply or from ±2 V to ±6 V on dual supplies. According to the Texas Instruments OPA705 manufacturer datasheet, the broad range allows the same amplifier topology to support both low-voltage portable systems and higher-voltage industrial instrumentation. Designers should still verify output swing, input common-mode range, and power dissipation at the selected supply voltage.
What are the key specifications of OPA705PA that engineers should know?
The OPA705PA is a single CMOS operational amplifier with 1 MHz gain-bandwidth product, 0.6 V/µs typical slew rate, 160 µA quiescent current, 0.5 mV typical input offset voltage, and 96 dB common-mode rejection. It provides rail-to-rail input and output operation in an 8-pin PDIP package. According to the manufacturer datasheet, these characteristics suit low-power instrumentation, buffering, and general-purpose analog signal conditioning.
Is OPA705PA suitable for low-voltage battery-powered applications?
The OPA705PA is suitable for many low-voltage battery-powered signal chains because it supports a 4 V to 12 V single supply and consumes 160 µA quiescent current. Its rail-to-rail inputs help preserve dynamic range in compact systems, although the actual battery run time also depends on load current, leakage, regulator efficiency, and the duty cycle. Confirm the output-swing limits at the lowest battery voltage.
Where can I download the OPA705PA datasheet PDF?
The OPA705PA datasheet PDF is available from the Texas Instruments product documentation and the verified manufacturer-linked datasheet listing on this page. The document describes the OPA705 family’s electrical characteristics, rail-to-rail behavior, supply ranges, package options, and ordering information. Use the Texas Instruments OPA705 product page as the starting point for the current manufacturer documentation and package variants.
Where can I find the OPA705PA pinout?
The OPA705PA pin assignment is shown in the pin-configuration section of the Texas Instruments OPA705 manufacturer datasheet. The component is an 8-pin PDIP single-amplifier package, so its schematic symbol and PCB footprint must use the datasheet’s exact power, input, and output pin positions. Do not assume that the PDIP-8 assignment is interchangeable with every single-op-amp SOIC-8 or dual-amplifier DIP-8 device.
What is the bandwidth and slew rate of OPA705PA?
The OPA705PA has a 1 MHz gain-bandwidth product and a typical slew rate of 0.6 V/µs. According to the Texas Instruments OPA705 datasheet, these are the primary dynamic-performance figures for this low-power CMOS amplifier. A 1 MHz gain-bandwidth product supports useful closed-loop gain at low frequencies, while the 0.6 V/µs slew rate limits large-signal response and should be checked against waveform rise-time requirements.
Does OPA705PA have rail-to-rail input and output?
The OPA705PA has rail-to-rail input and output characteristics. Rail-to-rail input operation allows the input common-mode voltage to extend close to the supply rails, while rail-to-rail output operation expands the available output-voltage range. These features are particularly useful in low-supply systems where the signal occupies much of the available voltage range. Actual output swing under load remains subject to the datasheet limits.
How does OPA705PA compare with OPA705UA?
OPA705PA and OPA705UA belong to the same Texas Instruments OPA705 family, but their mechanical packages differ. OPA705PA is the 8-pin PDIP through-hole option, while OPA705UA is associated with the standard SO-8 surface-mount option. Their electrical function is closely related, but they are not pin-to-pin drop-ins for PCB interchange because the package dimensions, mounting method, and land pattern differ.
What is the difference between OPA705 and OPA2705?
OPA705 is the single-amplifier version, while OPA2705 is the dual-amplifier version of the related family. The verified Texas Instruments ordering information lists OPA705 in SOT23-5, SO-8, and PDIP configurations and OPA2705 in MSOP-8, SO-8, and DIP-8 configurations. A single-versus-dual device is therefore not a package-compatible substitution unless the PCB footprint and circuit requirements have been specifically designed for that change.
When should I choose OPA705PA over a surface-mount OPA705 option?
Choose OPA705PA when through-hole assembly, manual prototyping, breadboard-friendly mechanical access, or a straightforward PDIP-8 footprint is more important than minimum board area. Choose a surface-mount OPA705 option when the PCB needs higher routing density or automated assembly. Both approaches require the same core signal-path review: confirm supply range, common-mode limits, output swing, stability with the selected feedback network, and available operating temperature range.
What is the best drop-in replacement for OPA705PA?
The best replacement is the part with the same PDIP-8 footprint, pin assignments, supply range, input and output architecture, and acceptable dynamic performance. The verified cross-reference results do not identify five or more confirmed pin-compatible replacements for OPA705PA. Treat the Texas Instruments OPA705 family as the primary source of alternatives, and validate any proposed substitute against the manufacturer pin configuration, electrical characteristics, and application-specific stability requirements.
Can a cross-brand single op amp replace OPA705PA without PCB changes?
A cross-brand amplifier can replace OPA705PA only after its PDIP-8 pinout, power polarity, input bias and offset behavior, common-mode range, output swing, gain-bandwidth product, slew rate, stability, and package dimensions have been verified. The available cross-reference results do not confirm a specific cross-brand pin-compatible part. Avoid selecting a replacement solely by matching the 1 MHz bandwidth because input and output architecture differences can alter system behavior.
Where can I buy OPA705PA and check current price and lead time?
Use the Request a Quote form on this page to request current OPA705PA pricing, stock status, lead time, and order quantities. The manufacturer product page and part-details page identify OPA705PA as the PDIP-8 ordering option of the single OPA705 family. Commercial terms can change with quantity and market conditions, so a quotation response is more reliable than a static product-page price.
Is OPA705PA in stock?
Current OPA705PA inventory should be confirmed through the Request a Quote form on this page because stock levels and lead times vary by package, order quantity, and market conditions. The verified product information identifies the device as an active Texas Instruments ordering option and lists an 8-PDIP package. Submit the required quantity, target date, and shipment location to obtain a current availability response.
How is OPA705PA used in sensor signal-conditioning circuits?
OPA705PA can serve as the input buffer or gain stage of a sensor interface because it offers rail-to-rail input behavior, 96 dB common-mode rejection, low offset voltage, and low input bias current. In a typical non-inverting amplifier, the feedback network determines the closed-loop gain, while the 1 MHz gain-bandwidth product limits usable bandwidth. Check sensor output impedance, common-mode range, noise requirements, and output loading before finalizing the stage.

엔지니어링 참조 데이터: OPA705PA — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose OPA705PA when the design needs a single, low-power CMOS operational amplifier with rail-to-rail input and output behavior, a 4 V to 12 V single-supply range, 1 MHz gain-bandwidth product, and a through-hole PDIP-8 footprint. It is particularly useful for prototypes, low-frequency instrumentation, sensor buffering, and compact single-supply signal-conditioning stages where manual assembly or simple DIP construction is valuable. OPA705UA may be preferable when a surface-mount SO-8 layout is required, but it is not a package-compatible drop-in for a board designed around OPA705PA. Before approving any other substitute, verify the exact eight-pin assignment, package dimensions, common-mode range, output swing, offset, bias current, bandwidth, slew rate, stability, and operating-temperature requirements. Do not select a dual amplifier merely because it offers two channels, and do not assume that a 1 MHz bandwidth match guarantees equivalent low-noise, rail-to-rail, or power-consumption behavior.

대체품과의 비교

파라미터 이 제품
Brand Texas Instruments
Package 8-pin PDIP
Amplifier Type Single operational amplifier
Architecture CMOS
Nominal Supply Voltage 12 V
Single-Supply Operating Range 4 V to 12 V
Dual-Supply Operating Range ±2 V to ±6 V
Gain-Bandwidth Product 1 MHz
Slew Rate 0.6 V/µs
Quiescent Current 160 µA
Input Offset Voltage 0.5 mV typical
Common-Mode Rejection Ratio 96 dB
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail

설계 노트

Place the OPA705PA close to the source and load to minimize parasitic pickup and feedback-loop delay. Connect the supply bypass capacitor directly between the V+ and V− pins, with a short ground return to the signal reference. Keep the input traces away from switching nodes and high-current return paths. Because this is an 8-pin PDIP package, provide adequate through-hole spacing and mechanical clearance for the socket or board.

Do not interpret the rail-to-rail designation as zero output resistance or unlimited output swing. Check the output voltage limits over the required supply range, temperature interval, and load current. Similarly, confirm that the sensor or source voltage remains within the common-mode range at startup and during transients. A single-supply circuit must also account for the ground reference when calculating the full-scale input range.

Use the 1 MHz gain-bandwidth product and 0.6 V/µs slew-rate figures to establish a practical bandwidth and rise-time limit for each gain stage. Check feedback-network impedance, capacitive loading, and noise gain because they can affect closed-loop response and stability. For sensor interfaces, favor a short, guarded input route and place any filtering resistor or capacitor directly at the amplifier input.

Calculate amplifier dissipation from the actual supply voltage, output voltage, and load current using the difference between input and output voltage multiplied by output current. The 160 µA figure describes quiescent current and does not include load-dependent output current. Ensure the 12 V maximum operating condition, package temperature rise, and adjacent component tolerances remain acceptable under worst-case supply and load.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the verified product information. Confirm current compliance documents from Texas Instruments before procurement.

관련 검색

OPA705PA datasheet OPA705PA datasheet pdf OPA705PA pinout OPA705PA specifications OPA705PA equivalent OPA705PA replacement OPA705PA cross reference OPA705PA schematic OPA705PA footprint Texas Instruments OPA705PA OPA705PA price OPA705PA stock

관련 부품 & 용어

Texas Instruments OPA705 OPA705PA OPA705UA OPA2705 operational amplifier op amp amplifier IC CMOS rail-to-rail input rail-to-rail output gain-bandwidth product slew rate common-mode rejection ratio quiescent current input offset voltage PDIP-8 SO-8 SOT23-5 surface mount through-hole package sensor signal conditioning active filter voltage buffer
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기