PIC16F19175-E/PT - 8-bit 32MHz 14KB Flash LCD MCU | Microchip
MPN: PIC16F19175-E/PT ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $2.85 | $2.85 |
| 10 | $2.62 | $26.20 |
| 100 | $2.21 | $221.00 |
| 500 | $1.95 | $975.00 |
| 1,000 | $1.72 | $1,720.00 |
PIC16F19175-E/PT Overview
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as ADCs, timers, communication interfaces, and I/O pins. PIC® microcontrollers use a RISC architecture with a fixed instruction set optimized for deterministic real-time control, placing them in the broader hierarchy of microcontrollers -> embedded controllers -> semiconductor ICs. The XLP™ (eXtreme Low-Power) family is specifically tuned for battery-powered applications where sleep current is critical.
Key features include the integrated LCD charge pump that generates VLCD from the main supply without external boost components, 12-bit ADC2 with computation, dual low-power comparators with programmable reference, and Core Independent Peripherals (CIPs) that operate without CPU intervention. The device supports 1.8V-5.5V operation across the PIC16F19175 (F) variant with on-chip voltage regulator and brown-out reset. Intelligent Analog peripherals include the 12-bit ADC, 5/8-bit DAC, and zero-cross detect (ZCD) for TRIAC control.
The PIC16F19175 uses Microchip's enhanced mid-range 8-bit core running at 32 MHz with 8 MIPS throughput, supported by 14 KB self-programmable Flash, 1024 bytes SRAM, and 256 bytes high-endurance EEPROM (100k erase/write cycles). Hardware CIPs include the SMT (Signal Measurement Timer), CWG (Complementary Waveform Generator), and Configurable Logic Cell, enabling complex timing and signal generation tasks without software overhead.
Typical applications include battery-powered glucose meters and blood pressure monitors with LCD readout, smart thermostats and HVAC controllers, industrial sensor transmitters with LCD display, electronic shelf labels (ESL), utility metering endpoints with LCD, and remote control units with status display. The integrated LCD driver supporting up to 357 segments eliminates external display drivers.
When designing with this device, pay attention to VLCD charge pump capacitor selection and consider the 5x8 font ROM for ASCII character generation. The PPS (Peripheral Pin Select) provides flexible I/O mapping, but designers must still respect analog/digital pin separation to avoid injection current issues.
Drop-in alternatives for PIC16F19175-E/PT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with PIC16F19175-E/PT (same form factor and footprint) — differing in ADC, Package, Comparators, Core, I/O Pins.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
PIC16F19175-I/PT
✅ Drop-In📋 Reference alternative (not in catalog)
PIC16F19176-I/PT
✅ Drop-In✓ In Stock
$1.85 / Unit
View Datasheet →PIC16F19175-E/MV
✅ Drop-In✓ In Stock
$1.78 / Unit
View Datasheet →PIC16F18875-E/PT
✅ Drop-In✓ In Stock
$1.42 / Unit
View Datasheet →PIC16F18877-I/PT
✅ Drop-In✓ In Stock
$2.18 / Unit
View Datasheet →PIC16F19175-E/PT Maximum Ratings & Electrical Characteristics
| Series | PIC® XLP™ 16F |
| Core | 8-bit PIC RISC (enhanced mid-range) |
| Program Memory Size | 14 KB (8K x 14 words) Flash |
| RAM Size | 1024 bytes |
| EEPROM Size | 256 bytes |
| Maximum CPU Frequency | 32 MHz |
| Instruction Throughput | 8 MIPS |
| Operating Voltage Range | 2.3 V to 5.5 V |
| I/O Pins | 36 |
| Package | 44-pin TQFP (10x10 mm) |
| Mounting Type | Surface Mount |
| Operating Temperature | -40C to +125C (E = Extended) |
| LCD Driver | Integrated with charge pump (up to 357 segments) |
| ADC | 12-bit ADC2 with computation |
| DAC | 5-bit / 8-bit DAC |
| Comparators | Low-power comparators with programmable reference |
| Timers | SMT, PWM, CCP, CWG |
| Communication | I2C, SPI, UART, EUSART |
| MSL Level | 3 (168 hours) |
| RoHS Status | Compliant |
PIC16F19175-E/PT Pin Configuration
| Pin 1 | RA5 — Digital I/O / analog input / LCD segment |
| Pin 2 | RA4 — Digital I/O / analog input / LCD segment |
| Pin 3 | RA3 — Digital I/O / analog input / LCD segment |
| Pin 4 | RA2 — Digital I/O / analog input / DAC output |
| Pin 5 | RA1 — Digital I/O / analog input / DAC reference |
| Pin 6 | RA0 — Digital I/O / analog input |
| Pin 7 | VDD — Positive supply voltage |
| Pin 8 | VSS — Ground reference |
| Pin 9 | OSC1/CLKIN — Crystal oscillator input / external clock |
| Pin 10 | OSC2/CLKOUT — Crystal oscillator output |
| Pin 11 | RC0 — Digital I/O / LCD segment |
| Pin 12 | RC1 — Digital I/O / LCD segment |
| Pin 13 | RC2 — Digital I/O / LCD segment |
| Pin 14 | RC3 — Digital I/O / LCD segment |
| Pin 15 | RC4 — Digital I/O / LCD segment |
| Pin 16 | RC5 — Digital I/O / LCD segment |
| Pin 17 | RC6 — Digital I/O / TX/CK |
| Pin 18 | RC7 — Digital I/O / RX/DT |
| Pin 19 | VSS — Ground reference |
| Pin 20 | VDD — Positive supply voltage |
| Pin 21 | RB0 — Digital I/O / interrupt-on-change / LCD segment |
| Pin 22 | RB1 — Digital I/O / LCD segment |
| Pin 23 | RB2 — Digital I/O / LCD segment |
| Pin 24 | RB3 — Digital I/O / LCD segment |
| Pin 25 | RB4 — Digital I/O / LCD segment |
| Pin 26 | RB5 — Digital I/O / LCD segment |
| Pin 27 | RB6 — Digital I/O / ICD clock |
| Pin 28 | RB7 — Digital I/O / ICD data |
| Pin 29 | RD0 — Digital I/O / LCD segment |
| Pin 30 | RD1 — Digital I/O / LCD segment |
| Pin 31 | RD2 — Digital I/O / LCD segment |
| Pin 32 | RD3 — Digital I/O / LCD segment |
| Pin 33 | RD4 — Digital I/O / LCD segment |
| Pin 34 | RD5 — Digital I/O / LCD segment |
| Pin 35 | RD6 — Digital I/O / LCD segment |
| Pin 36 | RD7 — Digital I/O / LCD segment |
| Pin 37 | RE0 — Digital I/O / LCD segment |
| Pin 38 | RE1 — Digital I/O / LCD segment |
| Pin 39 | RE2 — Digital I/O / LCD segment |
| Pin 40 | RE3 — Digital I/O / MCLR (if configured) |
| Pin 41 | VLCD — LCD bias voltage (charge pump output) |
| Pin 42 | COM0 — LCD common line 0 |
| Pin 43 | COM1 — LCD common line 1 |
| Pin 44 | MCLR — Master clear reset (active low) |
Typical Applications
PIC16F19175-E/PT is suitable for 6 applications: Battery-Powered Glucose Meter with LCD, Smart Thermostat with Segment LCD, Electronic Shelf Label (ESL) Display, Industrial Sensor Transmitter with LCD, Remote Control with Status LCD, Utility Meter Endpoint with LCD.
Battery-Powered Glucose Meter with LCD
The PIC16F19175-E/PT is ideal for battery-powered glucose meters requiring a long-life segment LCD readout. Its integrated LCD driver with charge pump eliminates the external boost converter, while 14 KB Flash stores the measurement algorithm and 256-byte EEPROM retains calibration constants across power cycles. The 12-bit ADC2 with computation directly interfaces with the electrochemical test strip, providing ratiometric readings without CPU overhead. Typical quiescent current below 1 uA in sleep with LCD refresh active enables 5+ year battery life on two AAA cells.
Recommended
Smart Thermostat with Segment LCD
The PIC16F19175-E/PT powers the smart thermostat mainboard, driving a 4x40 segment LCD that displays temperature, setpoint, and humidity. The integrated charge pump generates VLCD from 3.3V main supply, avoiding external DC-DC converters and reducing BOM cost. The SMT (Signal Measurement Timer) accurately captures zero-cross timing for TRIAC-based heater control via the CWG peripheral and ZCD. Core Independent Peripherals (CIPs) handle the temperature sensor polling without CPU wake-up, enabling sub-1 uA idle current.
Recommended
Electronic Shelf Label (ESL) Display
The PIC16F19175-E/PT drives electronic shelf label displays in retail environments where battery life over 5 years is required. Its XLP features including 30 nA sleep current and integrated LCD charge pump enable coin-cell operation that would otherwise require bulky battery packs. The 12-bit ADC2 monitors battery voltage for low-battery warnings, while the UART handles RF module wake-up for price updates. The 256-byte EEPROM stores the last-displayed price during battery replacement.
Recommended
Industrial Sensor Transmitter with LCD
The PIC16F19175-E/PT powers 4-20 mA loop-powered industrial sensor transmitters with local LCD readout for pressure, flow, or temperature measurements. The integrated LCD driver shows process variables in real time without external components, while the 12-bit ADC2 digitizes sensor outputs with computation averaging built in. The extended -40C to +125C temperature range and high-immunity analog front-end suit harsh industrial environments. The low-power comparators detect loop current for HART-compatible modulation.
Recommended
Remote Control with Status LCD
The PIC16F19175-E/PT powers handheld remote controls with a small segment LCD that displays battery status, channel, and menu. The integrated LCD driver and charge pump allow direct battery connection without boost circuitry. The CWG and PWM peripherals generate IR carrier frequencies while the SMT timer precisely measures incoming IR pulses. Sleep current below 1 uA extends battery life to multi-year operation even with frequent button presses waking the CPU.
Recommended
Utility Meter Endpoint with LCD
The PIC16F19175-E/PT serves as the MCU in smart utility meter endpoints (gas, water, electric) where an LCD displays cumulative consumption. The XLP features extend battery life to 10+ years on the meter's primary cell, while the integrated LCD driver with charge pump operates the display directly from 3.6V lithium thionyl chloride. The UART/I2C/SPI interfaces connect to wireless M-Bus or LoRaWAN modules for AMI backhaul. The 256-byte EEPROM logs hourly consumption profiles for offline diagnostics.
Recommended
Recommended Products Summary
Engineering reference data for PIC16F19175-E/PT — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | PIC16F19175-I/PT | PIC16F19176-I/PT | PIC16F18875-E/PT | PIC16F18877-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin TQFP (10x10 mm) | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same |
| Flash Memory | 14 KB | 14 KB | 28 KB | 28 KB | 56 KB |
| RAM | 1024 bytes | 1024 bytes | 2048 bytes | 2048 bytes | 4096 bytes |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Integrated LCD Driver | Yes (with charge pump) | Yes (with charge pump) | Yes (with charge pump) | No | No |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Temperature | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +85C (Industrial) |
| Unit Price @ 1000 pcs (USD) | 1.72 | 1.62 | 1.82 | 1.92 | 2.35 |
Key Differentiators
- Integrated LCD driver with charge pump (vs PIC16F18875-E/PT)
- XLP sleep current below 1 uA with LCD active (vs PIC16F19175-I/PT)
- Core Independent Peripherals (CIPs) (vs DSPIC30F3014-30I/PT)
Design Notes
The PIC16F19175-E/PT supports multiple low-power modes including SLEEP, IDLE, and DOZE. Sleep current with LCD charge pump active is typically below 1 uA, making the device ideal for battery-powered applications. Use the LCD charge pump in sleep mode to maintain display refresh without CPU intervention. Configure unused peripherals to their lowest power state via the PMDx registers and disable the ADC and comparators when not in use to achieve minimum quiescent current.
Place decoupling capacitors (100 nF ceramic plus 1 uF bulk) within 5 mm of each VDD/VSS pair on the 44-pin TQFP package. Connect all VSS pins to a single ground plane, and place the VLCD charge pump capacitors (typically 1 nF to 10 nF ceramic) close to the VLCD pin to minimize ripple. The crystal oscillator traces must be short and surrounded by ground pour; avoid routing digital signals under the crystal or charge pump capacitors to prevent noise injection into the LCD bias.
Do not exceed the absolute maximum ratings of 6.5V on VDD or inject current into analog pins when the device is unpowered. Always configure the PPS (Peripheral Pin Select) carefully - some peripheral functions are only available on specific pins. Verify the MCLR pin configuration: by default MCLR is enabled and requires a pull-up resistor; if unused, configure as a digital input to avoid unwanted resets. The LCD segment pins have specific drive strength limitations when used at high segment counts.
When routing the 32 MHz HFINTOSC clock output (CLKOUT), keep the trace under 25 mm and avoid parallel runs with analog signals. The SMT (Signal Measurement Timer) input pins require a clean signal - add a 1k series resistor at the source if driving from an external noisy source. For UART communication with wireless modules, add 100 ohm series resistors at TX/RX to dampen reflections on long traces. The 12-bit ADC2 achieves best results with an input bandwidth filter below 10 kHz.
Compliance Information
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - the standard -E/PT grade is extended industrial; automotive variants carry -VAO suffix.