SP3232EBET-L/TR - 2/2 RS-232 Transceiver | MaxLinear
MPN: SP3232EBET-L/TR ✗ End of LifeSP3232EBET-L/TR Overview
An RS-232 transceiver is an interface IC that combines line drivers and receivers for communicating between computers, embedded controllers, instruments, and other equipment using the EIA/TIA-232-F physical layer. The SP3232EB belongs to the interface-IC hierarchy, combining RS-232 drivers and receivers with a charge-pump power supply. According to the MaxLinear product page, its high-efficiency charge-pump design permits true RS-232 operation from a single 3.3 V supply while using only 0.1 uF capacitors in 3.3 V operation.
The primary specifications include two drivers, two receivers, a 3 V to 5.5 V supply range, and a maximum transmission rate of 250 kbps under load. The series is intended to meet true EIA/TIA-232-F standards. Its two-driver, two-receiver arrangement supports full-duplex serial links where each direction can carry data independently, while its low-voltage supply operation simplifies integration with modern 3.3 V digital systems.
The SP3222EB and SP3232EB families use an on-chip charge-pump network to generate the positive and negative voltage levels required by RS-232. This approach eliminates a separate negative supply and reduces the number of external storage capacitors compared with older discrete RS-232 implementations. The SP3232EB configuration adds a second driver and receiver relative to the SP3222EB family, making it appropriate for links requiring two channels or a full-duplex interface.
Typical uses include portable computers and palmtop computers, serial-port adapters, industrial control interfaces, point-of-sale equipment, test and measurement instruments, and embedded systems that exchange data with RS-232 peripherals. In a typical design, the logic-side TXD and RXD pins connect to a microcontroller UART, while R1OUT and R2OUT drive the external RS-232 line through the required protection and signal-integrity network.
Designers should follow the manufacturer datasheet for the exact capacitor values, charge-pump connections, driver output levels, receiver thresholds, and layout guidance. Place the charge-pump capacitors close to their specified pins, maintain the required RS-232 line impedance, and validate both driver and receiver behavior over the full system voltage and temperature range. Because SP3232EBET-L/TR is listed as obsolete and no longer manufactured, production availability should be confirmed before committing a new design.
Drop-in alternatives for SP3232EBET-L/TR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
ST3232EBWR
✅ Drop-In📋 Reference alternative (not in catalog)
SP3232EBET-L/TR Specifications
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2/2 full RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Transmission Rate | 250 kbps under load |
| Interface Standard | EIA/TIA-232-F |
| Package | 16-SOIC |
| Package Width | 7.50 mm |
| Package Body Width | 0.295 inch |
| Packaging | Tape and reel |
| Power Supply Architecture | High-efficiency charge-pump power supply |
| Charge-Pump Capacitor Value | 0.1 uF in 3.3 V operation |
| Single-Supply Operation | 3.3 V |
| Lifecycle Status | Obsolete and no longer manufactured |
SP3232EBET-L/TR 0.295 inch Pin Configuration Guide
Pin configuration for SP3232EBET-L/TR (0.295 inch package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for SP3232EBET-L/TR.
Refer to the datasheet for full pin configuration.
Typical Applications
SP3232EBET-L/TR is suitable for 6 applications: Portable Computer Serial Interface, Industrial Serial Control Interface, Point-of-Sale Equipment Interface, Test and Measurement Instrument, Embedded Controller Communication, Serial Port Adapter.
Portable Computer Serial Interface
The SP3232EBET-L/TR fits legacy RS-232 ports in portable and hand-held computers because its 3 V to 5.5 V supply range supports modern low-voltage system rails while the internal charge-pump creates the bipolar levels required by the RS-232 interface. The two-driver, two-receiver arrangement supports two communications channels or full-duplex traffic. At up to 250 kbps under load, it can serve both configuration links and higher-rate peripheral connections. The manufacturer identifies portable computers and palmtops as primary applications for the SP3222EB/SP3232EB family.
Recommended
Industrial Serial Control Interface
The SP3232EBET-L/TR can connect a controller or test fixture to an RS-232 device when the system operates from a 3.3 V or 5 V rail. Its 2/2 driver-receiver configuration supports bidirectional command and response paths, while the 250 kbps under-load rating provides more bandwidth than a basic legacy UART port. The single-supply charge-pump implementation avoids requiring a separate negative rail. For new industrial equipment, verify the operating-temperature rating, ESD protection level, and current lifecycle status before adopting this obsolete ordering code.
Recommended
Point-of-Sale Equipment Interface
Point-of-sale terminals and peripheral equipment often retain RS-232 connectors despite the prevalence of USB. The SP3232EBET-L/TR provides two drivers and two receivers for connecting a host UART to receipt printers, scanners, scales, or service interfaces. Its 3 V to 5.5 V operating range allows use with embedded 3.3 V logic, and the charge-pump output removes the need for an external negative supply. The 250 kbps under-load rate supports fast command exchanges, although cable capacitance and grounding must be checked for each installation.
Recommended
Test and Measurement Instrument
The SP3232EBET-L/TR is suitable for RS-232 control and data connections in portable test and measurement equipment where a compact 16-SOIC interface and single-supply operation are valuable. Two channels can support separate transmit and receive paths or two instrument links, while the 250 kbps under-load specification accommodates instrument-control traffic. Use the manufacturer application guidance to select the required charge-pump capacitors, and place those capacitors close to the IC to minimize supply noise and ensure stable charge-pump operation.
Recommended
Embedded Controller Communication
The SP3232EBET-L/TR bridges a 3.3 V microcontroller UART and a physical RS-232 network. The MCU connects to the transceiver through standard logic-side driver-input and receiver-output signals, while the external side connects to the line drivers and receiver inputs through the application network. A 3.3 V supply allows operation without a negative rail, and the 0.1 uF capacitor configuration identified for 3.3 V operation simplifies board design. Keep logic and RS-232 nets separated appropriately and include the required line protection.
Recommended
Serial Port Adapter
A compact serial-port adapter can use the SP3232EBET-L/TR to add two RS-232 channels to a low-voltage embedded controller. Its 16-SOIC package provides a practical surface-mount implementation, and its 3 V to 5.5 V range covers common 3.3 V and 5 V designs. The two drivers and receivers permit simultaneous bidirectional operation, while the 250 kbps under-load rate supports higher-speed legacy links. Connector protection, ground continuity, cable length, and surge handling must be designed separately from the transceiver itself.
Recommended
Recommended Products Summary
Engineering reference data for SP3232EBET-L/TR — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ST3232EBWR |
|---|---|---|
| Package | 16-SOIC | 16-SOIC |
| Brand | MaxLinear, Inc. | STMicroelectronics |
Key Differentiators
- Documented two-channel RS-232 configuration (vs ST3232EBWR)
- Single low-voltage supply operation (vs ST3232EBWR)
- Explicit under-load throughput rating (vs ST3232EBWR)
Design Notes
Place the charge-pump capacitors directly beside the pins and connections identified in the MaxLinear SP3232EB family datasheet. The manufacturer states that 0.1 uF capacitors support 3.3 V operation; use that value only with the corresponding application configuration. Short capacitor paths reduce loop area and switching-node coupling, which helps prevent charge-pump noise from disturbing the logic-side UART signals.
Do not treat SP3232EBET-L and SP3232EBET-L/TR as interchangeable lifecycle choices without checking the suffix. Both identify 2/2 full-RS-232 devices in 16-SOIC technology, but /TR specifies tape-and-reel packing, and the /TR listing explicitly states that the part is obsolete and no longer manufactured. For new production, qualify an available replacement against the complete pinout, supply range, timing, and thermal requirements.
Design the external RS-232 network separately from the transceiver logic connections. Use the manufacturer-recommended driver and receiver interface components, preserve the intended signal-return path, and account for connector protection, cable capacitance, and ground noise. The stated 250 kbps under-load rating does not guarantee end-to-end performance over an arbitrary cable; verify rise time, reflections, and receiver thresholds in the assembled system.
Compliance Information
The manufacturer product page and distributor snippets do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this exact ordering code. AEC-Q100 qualification is not stated and is not applicable to the stated general-purpose RS-232 interface application.