STM32L011F3P6 - 32MHz Cortex-M0+ 8KB Flash MCU | ST
MPN: STM32L011F3P6 ✓ ActiveSTM32L011F3P6 Overview
An ultra-low-power microcontroller is a semiconductor designed to execute application software while minimizing active energy consumption and sleep-state leakage. The STM32L0 family combines an Arm Cortex-M0+ processor, embedded memory, low-power peripherals, and reset and supply-management functions within one device. This places the MCU in the wider hierarchy of embedded processing components: Arm Cortex-M0+ core, 32-bit microcontroller, integrated circuit, and embedded semiconductor.
The STM32L011F3P6 provides a 32 MHz maximum CPU frequency and 8 KB of Flash program memory in the STM32L011x3 access-line family. The manufacturer describes the family as ultra-low-power and includes reset and supply-management functions. Its 1.8 V, 2.5 V, and 3.3 V operating-voltage options allow operation from common low-voltage rails. The 20-pin TSSOP format supports surface-mount assembly while reducing PCB footprint requirements compared with larger leaded packages.
The Arm Cortex-M0+ architecture provides a compact instruction set suited to control tasks, peripheral configuration, communication, and simple signal processing. The STM32L011F3P6 integrates the processor and application resources into a small device, reducing the number of external components needed for basic embedded systems. Firmware development can use the STM32 family ecosystem, while designers must confirm peripheral availability, pin multiplexing, and electrical limits against the manufacturer documentation before assigning a function to each package pin.
Typical applications include low-power sensor nodes, battery-operated measurement instruments, compact motor and actuator controllers, appliance controls, and small industrial control modules. The MCU is particularly relevant when a design needs more processing capability than a basic logic device but must retain a small package and low-voltage operation. For connected products, peripheral availability and communication requirements should be checked against the exact device variant before schematic capture.
PCB planning should reserve the manufacturer-specified decoupling capacitors, oscillator components when required, programming access, and exposed ground connections for the selected 20-pin TSSOP footprint. Power rails must remain within the supported voltage range, and unused inputs should be configured appropriately to avoid unintended current consumption. Firmware should exercise the low-power modes only after clocks, peripherals, and wake sources have been validated.
This product page organizes the key STM32L011F3P6 characteristics, sourcing information, package considerations, application guidance, and documented substitute constraints. It also distinguishes the target device from related STM32 variants so engineers can assess memory, package, voltage, and peripheral differences before committing a design to production.
Drop-in alternatives for STM32L011F3P6 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with STM32L011F3P6 (same form factor and footprint) — differing in Flash Memory, Package.
STM32L011F4P6TR
✅ Drop-In📋 Reference alternative (not in catalog)
STM32L010F4P6TR
✅ Drop-In📋 Reference alternative (not in catalog)
STM32L011F3P6 Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit ultra-low-power microcontroller |
| Manufacturer | STMicroelectronics |
| CPU Core | Arm Cortex-M0+ |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 8 KB (8K x 8) |
| Operating Voltage | 1.8 V, 2.5 V, or 3.3 V |
| Package | 20-pin TSSOP |
| Mounting Type | Surface mount |
| Product Family | STM32L011x3/4 access line |
| Power Class | Ultra-low-power |
| Supply Management | Integrated reset and supply management |
STM32L011F3P6 20-pin tssop Pin Configuration Guide
Pin configuration for STM32L011F3P6 (20-pin tssop package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for STM32L011F3P6.
Refer to the datasheet for full pin configuration.
Typical Applications
STM32L011F3P6 is suitable for 6 applications: Battery-Powered Sensor Nodes, Battery-Operated Measurement Instruments, Compact Appliance Controls, Small Motor and Actuator Controllers, Low-Power IoT Endpoint Controllers, Programmable Embedded Control Modules.
Battery-Powered Sensor Nodes
The STM32L011F3P6 fits compact sensor nodes because its Arm Cortex-M0+ core operates at up to 32 MHz while the STM32L011x3/4 family is positioned for ultra-low-power operation. The 8 KB of Flash can hold a focused acquisition and communication routine, while operation from 1.8 V, 2.5 V, or 3.3 V supports common energy-harvesting and battery rails. Place the MCU beside the sensor interface, route the ground plane beneath the device, and validate the sleep-mode current, wake sources, and duty-cycle budget on the assembled board.
Recommended
Battery-Operated Measurement Instruments
A portable meter or simple data logger can use the STM32L011F3P6 for control, scaling, local status handling, and measurement-system supervision. Its 32-bit Cortex-M0+ processor provides more general-purpose capability than a basic logic controller, while 8 KB of Flash supports a deliberately compact firmware image. The 20-pin TSSOP package reduces board width in handheld products. Engineering teams should confirm that the selected pin assignments expose the required ADC, timer, serial interface, and reset functions before freezing the enclosure and PCB design.
Recommended
Compact Appliance Controls
The STM32L011F3P6 is appropriate for appliance subassemblies that coordinate buttons, indicators, sensors, and small actuators. Its 32 MHz Cortex-M0+ core can handle a real-time control loop and peripheral interrupts, while the low-power family positioning supports battery or efficient line-powered operation. The three listed operating voltages permit integration with mixed-voltage control boards. Keep high-current switching devices away from the MCU area, provide local supply decoupling, and define a safe firmware state for every input and output during reset or firmware faults.
Recommended
Small Motor and Actuator Controllers
For compact motor or actuator modules, the STM32L011F3P6 can manage command decoding, limit sensing, timing, and status reporting through its embedded control resources. The 32-bit Cortex-M0+ architecture is suitable for deterministic supervisory tasks, and the 20-pin TSSOP package can be mounted close to the controlled mechanism. The design must verify the exact timer outputs, capture inputs, and alternate functions in the package pin table. Use transistor drivers and protection networks rather than driving inductive loads directly from MCU pins.
Recommended
Low-Power IoT Endpoint Controllers
The STM32L011F3P6 can serve as the local endpoint controller in a small IoT product when the radio or network module handles high-bandwidth communication and the MCU manages sensing, configuration, and power management. Its 1.8 V, 2.5 V, and 3.3 V operation supports common interface levels, and the 32-pin-independent TSSOP-20 footprint simplifies compact board assembly. Confirm UART, SPI, or I2C availability and pin multiplexing in the manufacturer documentation. Synchronization and wake latency should be measured with the complete radio, regulator, and sensor load.
Recommended
Programmable Embedded Control Modules
The STM32L011F3P6 fits small programmable modules that consolidate sensing, control, and serial configuration into one board. Its 8 KB of Flash and 32 MHz Cortex-M0+ execution support focused embedded firmware, and the 20-pin TSSOP package allows a compact module outline. Designers should reserve the documented programming interface, decoupling positions, and all power pins. Validate boot behavior, reset thresholds, and firmware update workflows on production hardware because package pin assignment and memory configuration determine whether an existing module can be reused without modification.
Recommended
Recommended Products Summary
Engineering reference data for STM32L011F3P6 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | STM32L011F4P6TR | STM32L010F4P6TR |
|---|---|---|---|
| Package | TSSOP-20 | TSSOP-20 | TSSOP-20 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Product Family | STM32L011x3/4 access line | STM32L011x3/4 family | STM32L010 family |
| Delivery Format | Tube | Tape and reel | Tape and reel |
Key Differentiators
- Exact 8 KB target configuration (vs STM32L011F4P6TR)
- Targeted STM32L011 access-line positioning (vs STM32L010F4P6TR)
- Compact 20-pin surface-mount implementation (vs STM32L011F4P6TR)
Design Notes
Use the manufacturer STM32L011x3/4 package drawing and land pattern when laying out the 20-pin TSSOP footprint. Verify pin-1 orientation against the PCB library, maintain the specified power and ground connections, and place the required decoupling capacitors immediately adjacent to their corresponding pins. Keep the analog or sensitive signal path away from switching nodes and provide a continuous ground reference beneath the device.
Design the supply network for the STM32L011F3P6's supported 1.8 V, 2.5 V, and 3.3 V operating conditions. Select the rail used by the complete board rather than assuming every peripheral shares the same voltage. Check startup, reset thresholds, brownout behavior, and regulator quiescent current against the power budget. For battery applications, include the MCU sleep current and peripheral leakage in the calculated operating life rather than using active-current figures alone.
Do not infer pin compatibility from the Cortex-M0+ core name alone. A substitution can differ in Flash size, memory map, peripheral availability, alternate functions, and startup behavior. When evaluating STM32L011F4P6TR or STM32L010F4P6TR, compare the exact ordering code, package drawing, pin-definition table, device features, and firmware assumptions. Rebuild and test the production PCB whenever a component change affects the BOM.
Keep oscillator and timing-sensitive routes short, and avoid routing high-current switching paths beneath or immediately beside the MCU. Separate sensitive analog inputs from digital control signals where practical, provide a low-impedance ground return, and use test points for supply, reset, programming, and selected communication interfaces. If the application relies on low-power operation, inspect leakage paths from external pull-ups, LEDs, level shifters, and connected peripherals.
Compliance Information
The cited product descriptions do not state a specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements using the current manufacturer product documentation and applicable customer qualification records.