ADC/DAC
Produtos (2518)
ADC1410S105HN/C1:5 - 14-Bit 105MSPS Pipelined ADC | NXP
NXP ADC1410S105HN/C1:5 is a single-channel 14-bit pipelined Analog-to-Digital Converter sampling at 105 Msps, packaged in a 40-pin HVQFN (6x6 mm) with exposed thermal pad. The device offers CMOS or LVDS DDR digital outputs, one differential/single-ended analog input, and a serial SPI configuration interface. According to the NXP datasheet, the ADC1410S105HN/C1:5 is optimized for high dynamic performance at low power while supporting a -40°C to +85°C industrial temperature range. What is a pipelined ADC? A pipelined Analog-to-Digital Converter is a multi-stage converter architecture that uses cascaded low-resolution sub-ADCs to digitize analog signals at high sample rates (tens to hundreds of Msps) while maintaining low latency per conversion cycle. Pipelined ADCs sit in the broader hierarchy of Nyquist-rate ADCs (SAR, pipeline, flash), distinguishing them from oversampling delta-sigma converters; in a signal chain they follow the analog front end (AFE) and feed FPGAs, DSPs, or processors that perform demodulation, FFT, or digital filtering. Key features of the ADC1410S105HN/C1:5 include 14-bit resolution, 105 Msps maximum sampling rate, selectable CMOS or LVDS DDR digital outputs, serial SPI control interface, integrated input buffering, and 40-pin HVQFN package with thermally efficient exposed pad. The pipelined architecture provides consistent SNR/SFDR performance across the supported 65/80/105/125 Msps family sample rates. Typical applications for this ADC include communications infrastructure (base stations, IF sampling), industrial imaging (medical ultrasound, machine vision), test and measurement (oscilloscopes, spectrum analyzers), high-speed data acquisition systems, and radar/LIDAR front-ends. The industrial temperature range suits outdoor or harsh-environment deployments. When designing with the ADC1410S105HN/C1:5, decouple the AVDD pins with 10µF tantalum plus 0.1µF ceramic capacitors placed as close to the pins as possible, and tie the exposed pad to a clean analog ground plane to achieve datasheet thermal resistance. For best SFDR, drive the input in differential mode and use a bandwidth-matched transformer or differential amplifier such as the ADA4937. This page synthesizes distributor pricing, drop-in alternatives (including 80 Msps, 125 Msps same-family variants and qualified cross-brand pin-compatible parts), and practical design notes not found in the manufacturer datasheet alone.
ADC1410S125HN-C1 - 14-bit 125 MSPS ADC, LVDS/CMOS | Renesas
The Renesas ADC1410S125HN-C1 is a single-channel 14-bit pipelined Analog-to-Digital Converter sampling at 125 MSPS with selectable CMOS or LVDS DDR digital outputs, housed in a 40-pin HVQFN (6 x 6 mm) exposed-pad package. It is optimized for high dynamic performance and low power consumption, integrating an input PGA and a serial SPI control interface for flexible configuration. The part belongs to Renesas's (formerly IDT) ADC1410S family, which also offers 65, 80, and 105 MSPS speed grades sharing the same pinout and package. An ADC (Analog-to-Digital Converter) is a data-converter integrated circuit that transforms a continuous-time, continuous-amplitude analog signal into a discrete-time, discrete-amplitude digital word. Within the broader semiconductor hierarchy, an ADC belongs to the data-converter IC family, which sits under mixed-signal ICs, which in turn sit under integrated circuits. Pipelined ADCs such as the ADC1410S125HN-C1 use a multi-stage switched-capacitor architecture to deliver high sample rates (tens to hundreds of MSPS) while maintaining low power and small die area, making them the dominant topology for communications, instrumentation, and imaging applications that need 10-16 bit resolution at high speed. Key specifications include 14-bit resolution, 125 MSPS maximum sample rate, 40-pin HVQFN package (6 x 6 mm, 0.85 mm height, MO-220 / SOT618-6), industrial temperature grade (-40 C to +85 C), serial SPI configuration interface, and selectable CMOS or LVDS DDR output modes. The LVDS DDR option delivers the digital word on both clock edges, halving the output clock frequency and simplifying board-level routing at 125 MSPS. Architecturally, the device uses a multi-bit pipelined core preceded by a sample-and-hold and input PGA, allowing the full-scale input range to be programmed via the SPI port. Output data is delivered through either parallel CMOS pins or LVDS DDR pairs, with the mode selected through the serial configuration interface. The integrated input buffer and on-chip reference simplify external BOM and shorten design-in time for multi-channel systems. Typical applications include wireless communications baseband and IF digitizers, medical imaging front-ends, portable test and measurement instruments, radar and lidar signal acquisition, and high-speed industrial data acquisition cards. Designers value the family for its consistent pinout across 65/80/105/125 MSPS grades, which lets one PCB accommodate multiple speed options without rework. When designing with this ADC, allocate adequate copper area beneath the exposed pad to keep junction temperature within the industrial range, and route the LVDS DDR pairs as 100 ohm differential lines with length matching. Decouple each supply pin with 100 nF plus 10 uF bulk capacitance placed as close as possible to the package. The SPI port operates at logic levels compatible with 1.8 V to 3.3 V host controllers. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes that are not collected in a single place on the manufacturer datasheet.
ADC1411S125HN/C1 - 14-Bit 125MSPS Single-Channel ADC | NXP
The NXP ADC1411S125HN/C1,5 is a 14-bit, single-channel, 125 MSPS analog-to-digital converter housed in a 32-pin HVQFN (SOT617-3) package with an exposed thermal pad for low thermal resistance. It is specified to function in industrial commercial and communication environments and supports sampling rates up to 125 MHz with the 1-channel input configuration that defines this 'C1' part variant. The converter integrates an input buffer and operates from a single 3.3 V supply rail. An analog-to-digital converter (ADC) is a mixed-signal data acquisition IC whose role is to translate continuous analog voltages into discrete digital codes at a defined sample rate. Within the broader IC taxonomy, the ADC1411S125HN/C1 is a successive-approximation is out, ADC is out, pipelined ADC is out, data converter is out, mixed-signal IC is out, integrated circuit is out, semiconductor. The 125 MSPS class of ADC bridges precision measurement and high-speed signal acquisition, supporting communications, instrumentation, and defense signal-processing designs. Key features include 14-bit resolution, 125 MSPS sample rate, single-channel analog input with on-chip input buffer, LVDS DDR and CMOS digital output interfaces, integrated clock duty cycle, false-to stabilize sample timing, SPI-compatible serial control interface for gain and offset trim, and a wide input bandwidth. The 32-pin HVQFN package provides an exposed thermal pad that reduces junction-to-themal resistance to 25 C/W, enabling reliable operation at the maximum 125 MSPS sample rate with no external heatsink required. The ADC1411S125HN/C1,5 is built on a low-power CMOS process and uses a pipelined architecture with on-chip input buffering. The pipeline stages are calibrated at power-up to provide low integral non-linearity and low differential non-linearity. The integrated input buffer presents high impedance to the analog source, simplifying front-end driver design. The internal reference voltage and duty-cycle stabilise functions further reduce board-level component count. The device is qualified per the NXP commercial-grade reliability flow and supports the -3 to +85C industrial temperature range. Typical applications include communications base-station receivers, industrial digitizers, medical imaging front ends, defense signal-intelligence systems, and high-end instrumentation. In base-station receivers, the 14-bit resolution at 125 MSPS provides sufficient dynamic range for IF sampling of multicarrier signals. When designing with this part, ensure the analog input is driven from a low-impedance, low-distortion source and that the LVDS outputs are terminated per the JESD8-2 LVDS specification. A 100 ohm differential termination at the receiver end is mandatory to minimize reflections. Differential gain on this device is 1.7 V FS, and the input is configured for 50 ohm matching. The digital supply AVDD should be decoupled with 100 nF and 10 uF capacitors placed within 2 inches of the supply pins.
ADC1411S125HN/C1:5 - 14-Bit 125MSPS ADC | NXP HVQFN-32
The NXP ADC1411S125HN/C1:5 is a 14-bit pipelined analog-to-digital converter (ADC) with a maximum sampling rate of 125 MSPS, supplied in a 32-pin HVQFN exposed-pad package. It uses a single 1.8 V analog supply and a separate 1.8 V to 3.3 V digital output supply, with a typical power dissipation of 250 mW at 125 MSPS full rate. The part provides LVCMOS digital outputs and supports both binary and two's-complement output coding for easy interface to FPGAs or microcontrollers. An ADC (analog-to-digital converter) is a data-acquisition component that samples continuous analog input signals and converts each sample into a binary code. Pipeline ADCs such as the ADC1411S125HN/C1:5 achieve high conversion rates (>100 MSPS) by distributing the conversion work over multiple low-resolution stages, making them the standard choice for IF undersampling, multi-carrier communications, medical imaging, and digital oscilloscope front-ends. Within the wider taxonomy, this part belongs to the data-converter IC family, which sits under the signal-chain category of mixed-signal semiconductors. Key features of the ADC1411S125HN/C1:5 include 14-bit resolution, 125 MSPS maximum conversion rate, a 73 dB SNR at 30 MHz input, and an effective-number-of-bits (ENOB) better than 11.5 bits. The device integrates an internal 1.0 V reference, internal input termination, and a programmable full-scale input range, eliminating several discrete components from the BOM. Built-in digital error correction within the pipeline architecture removes residual stage errors and improves linearity across the full clock range. Architecturally, the converter comprises a front-end differential Track-and-Hold amplifier, a multi-stage switched-capacitor pipeline, internal bandgap reference, and LVCMOS output drivers. The exposed thermal pad provides a low-thermal-resistance path to the PCB, allowing the converter to sustain 125 MSPS operation with only modest copper-area heatsinking on a standard 4-layer FR-4 board. Typical applications include wireless infrastructure IF sampling, multi-channel cellular base-station receivers, medical ultrasound beamformers, portable test and measurement instruments, and industrial data-acquisition systems. The wide input bandwidth (>500 MHz) also allows direct IF undersampling of intermediate-frequency signals in zero-IF and low-IF radio architectures. When designing the PCB, place the input traces in a tightly-coupled differential pair, decouple the AVCC pin with 100 nF plus 10 µF ceramic capacitors, and stitch the thermal pad with an array of thermal vias to the internal ground plane. Avoid routing digital LVCMOS outputs across the analog input region to maintain harmonic distortion (SFDR/THD) performance. This page consolidates distributor pricing for the ADC1411S125HN/C1:5, drop-in replacement candidates in the same HVQFN-32 footprint, and lab-validated design notes that go beyond the manufacturer datasheet summary.
ADC1412D065HN-C1 - Dual 14-bit 65 Msps ADC, 64-HVQFN | Renesas
The Renesas ADC1412D065HN-C1 is a dual-channel, 14-bit pipelined Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 65 Msps. The device integrates two simultaneously-sampling 14-bit ADC cores into a single 64-pin HVQFN (also referred to as 64-VFQFPN) package measuring 9x9 mm with an exposed thermal pad. What is a dual-channel pipelined ADC? A pipelined ADC is a high-speed analog-to-digital architecture that uses cascaded low-resolution flash stages with sample-and-hold and digital error correction to achieve 12-16 bits of resolution at tens to hundreds of Msps. A dual-channel ADC integrates two such converter cores with shared reference and clocking infrastructure, allowing simultaneous sampling of two input signals - critical for I/Q demodulation, multi-antenna receivers, and medical imaging. The ADC1412D065HN-C1 sits in the converter hierarchy as: ADC -> pipelined ADC -> dual-channel ADC -> data acquisition IC -> signal chain IC -> semiconductor. Key specifications include 14-bit resolution, a maximum sample rate of 65 Msps (with family variants at 80, 105, and 125 Msps), configurable CMOS or LVDS DDR digital outputs, an SPI configuration interface, and operation from a single 1.8V supply. The device accepts differential analog inputs and provides a serial SPI port for register access. The architecture targets communications infrastructure such as LTE base stations, multi-standard software-defined radios, and industrial ultrasound beamformers where two coherent channels must be captured at once. Design considerations include the need for a low-jitter differential clock source, a clean analog supply plane decoupled close to the AVDD pin, and a stable external reference. The LVDS DDR output mode (Double Data Rate, i.e., one sample per clock edge) reduces the number of required output lanes for glueless connection to an FPGA. Unlike consumer-tier single-channel ADCs such as the ADC12048, the dual-channel integration reduces board area and channel-matching error in I/Q paths. Ensure thermal pad soldering follows JEDEC J-STD-020 reflow profiles and that the exposed pad is soldered to the PCB ground plane for rated thermal performance.
ADC1412D065HN-C18 - Dual 14-bit 65Msps ADC | Renesas
The Renesas ADC1412D065HN-C18 is a dual-channel, 14-bit pipelined analog-to-digital converter sampling up to 65 Msps with selectable CMOS or LVDS DDR digital outputs, housed in a 64-pin VFQFPN (9x9 mm) package. Key specifications include 14-bit resolution, 2 input channels, 65 Msps maximum sample rate, and dual pipelined architecture with on-chip sample-and-hold. The integrated digital output formatter supports both parallel CMOS and LVDS DDR modes for flexible FPGA or ASIC interface. An analog-to-digital converter (ADC) is a data-acquisition component that converts continuous analog voltage signals into discrete digital codes for downstream processing by microcontrollers, DSPs, FPGAs, or ASICs. Within the broader taxonomy, pipelined ADCs occupy the high-speed tier of the converter family (above SAR and below flash), balancing sample rate, resolution, and power dissipation. The ADC1412D065HN-C18 is a member of the high-speed pipelined sub-category, optimized for communications, instrumentation, and medical imaging front ends. The ADC1412D065HN-C18 features dual simultaneously-sampling channels enabling coherent I/Q or differential acquisition, internal reference, and a low-jitter clock input. The selectable CMOS or LVDS DDR output interface simplifies board routing and reduces the number of digital traces required, particularly valuable in densely-populated baseband designs where signal integrity is critical. The pipelined architecture provides low-latency conversion, internal gain and offset calibration, and per-channel data alignment. Operating from a single analog supply (typically 3.3 V) and a separate digital supply (1.8 V or 3.3 V), the device supports flexible power-tree integration. Per Renesas, the part targets communications receivers, radar digitizers, ultrasound front-ends, and general-purpose high-speed data acquisition. Typical applications include wireless base-station receive chains, software-defined radio front-ends, medical ultrasound beamforming, and portable instrumentation. The 9x9 mm QFN footprint balances thermal dissipation and PCB area for multi-channel systems. When designing with this ADC, ensure the analog input network presents a low-jitter differential drive and that the LVDS outputs are length-matched to within the FPGA setup/hold window. Decouple AVDD and DVDD separately with bulk and ceramic capacitors placed close to the supply pins. This page synthesizes distributor pricing, drop-in alternatives from the Renesas and cross-brand product family, and practical design notes that are not duplicated on the manufacturer datasheet.
ADC1412D080HN-C1 - Dual 14-bit 80MSPS ADC | Renesas
The Renesas ADC1412D080HN-C1 is a dual 14-bit pipelined analog-to-digital converter sampling at 80 MSPS, housed in a 64-pin HVQFN (9x9 mm) package. According to the manufacturer datasheet, it supports 2 input channels per device with selectable CMOS or LVDS DDR digital outputs, making it suitable for high-density multi-channel signal acquisition systems. The device targets communications, instrumentation, and baseband digitization use cases that require simultaneous sampling of two correlated analog inputs. An ADC (Analog-to-Digital Converter) is a data acquisition integrated circuit that converts continuous-time analog signals into discrete digital codes, enabling downstream processing by microcontrollers, FPGAs, or DSPs. In the broader taxonomy, the ADC1412D080HN-C1 belongs to the class of pipeline ADCs, which interleave sub-ADCs and DACs to achieve high sample rates (the pipeline architecture -> successive-approximation/pipelined/sigma-delta ADC -> data converter -> data acquisition IC -> analog mixed-signal IC hierarchy). This topology delivers the best throughput-to-power trade-off in the 50-200 MSPS range. Key features include 14-bit resolution, 80 MSPS sampling rate, dual-channel simultaneous sampling, configurable CMOS or LVDS DDR output interface, and an industrial temperature range of -40C to +85C. The device supports a 3-wire SPI-compatible serial interface for configuration. The HVQFN-64 (9x9 mm) package has low thermal resistance and is suitable for high-density PCB layouts common in communications infrastructure equipment. The pipelined architecture uses a switched-capacitor front-end and digital error-correction logic, achieving low latency and high spurious-free dynamic range. The device requires an external reference and an external analog input driver, and the LVDS DDR mode minimizes the digital output bus width while preserving the 80 MSPS throughput, simplifying board-level routing between the ADC and the downstream FPGA receiver. Typical applications include multi-carrier cellular base stations, radar and lidar receiver front-ends, medical imaging digitizers, and high-end oscilloscopes or spectrum analyzers. The Renesas ADC1412D125HN-C1 (125 MSPS) and ADC1412D065HN-C1 (65 MSPS) variants cover the same application space at different sampling rates, all sharing the HVQFN-64 (9x9) footprint for design scalability. When designing with this device, prioritize proper grounding and power-rail decoupling; Renesas application briefs recommend a clean analog supply with a ferrite bead plus a 10uF/0.1uF capacitor stack on the AVDD pin. Note that the manufacturer marks this part Obsolete per Renesas documentation, so procurement should plan long lead times or evaluate current production parts from the ADC1412D family. This page consolidates distributor pricing, same-package drop-in alternatives, and design guidance beyond what is in the standalone Renesas datasheet, helping engineers source and integrate the ADC1412D080HN-C1 efficiently.
ADC1412D080HN-C18 - Dual 14-bit 80MSPS ADC, LVDS DDR | Renesas
The Renesas ADC1412D080HN-C18 is a dual-channel, 14-bit pipelined Analog-to-Digital Converter (ADC) sampling at 80 Msps with selectable CMOS or LVDS DDR digital outputs, housed in a 64-pin HVQFN (9x9 mm) package. The part is part of Renesas's ADC1412D SER family and provides two independent ADC channels optimized for high dynamic performance and low power consumption. Each channel features a 14-bit resolution with sample rates up to 80 Msps, making it well-suited for multi-channel receive paths where board density is constrained. A pipelined ADC is a multi-stage converter architecture that uses cascaded low-resolution stages with digital error correction to achieve high sampling rates while maintaining 12-16 bit resolution; this design pattern sits between successive-approximation (SAR) converters (which trade speed for resolution) and flash converters (which trade resolution for speed). The ADC1412D080 specifically targets mid-bandwidth communications, medical imaging front-ends, and industrial digitizer applications where dual-channel simultaneous sampling is required. Key differentiating features of the ADC1412D080HN-C18 include a dual 14-bit pipeline architecture, configurable CMOS or LVDS DDR output interfaces for system flexibility, sample rates of 80 Msps per channel, and a 64-pin HVQFN (9x9 mm) package with exposed thermal pad. According to the Renesas product page, the part supports pipelined operation optimized for high dynamic performance and low power, suitable for dense multi-channel PCB layouts. The wide sample-rate range of the family (65/80/105/125 Msps variants) lets designers scale performance across product tiers without changing PCB layout. The ADC1412D080HN-C18 is suited for communications receiver IF digitizers, multi-channel medical imaging systems, ultrasound front-ends, industrial test and measurement instrumentation, and broadband data acquisition systems. Its dual-channel architecture reduces component count versus two discrete ADCs, simplifying board layout and improving channel-to-channel matching for differential or I/Q signal acquisition. When designing with this device, ensure the input common-mode voltage is set within the specified range and that the LVDS DDR output traces are length-matched and 100-ohm differential terminated. The exposed pad must be soldered to a continuous ground plane for thermal dissipation and electrical performance. The part is listed as obsolete on the Renesas product page, so designers should verify last-time-buy status and qualified stock via authorized distributors before committing to new production designs.
ADC1412D105HN-C1 - Dual 14-bit 105MSPS ADC | Renesas/NXP
The Renesas (formerly Integrated Device Technology / NXP) ADC1412D105HN-C1 is a dual-channel 14-bit pipelined Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sampling rates up to 105 MSPS per channel, housed in a 64-pin HVQFN (SOT804-6) 9x9 mm package with an exposed thermal pad. The part supports CMOS or LVDS DDR digital outputs, two independently sampled input channels, and an SPI-compatible serial control interface for mode configuration. It is qualified to industrial temperature range (-40C to +85C). A pipelined ADC is a high-speed successive-approximation-style converter that splits the conversion into multiple low-resolution stages with a digital error-correction backend, achieving sample rates in the tens-to-hundreds of MSPS while keeping power dissipation modest. In the broader taxonomy it sits under ADC -> data converter -> signal-chain IC -> mixed-signal semiconductor. Pipelined ADCs are the workhorse of IF/RF digitisation, communications baseband, medical imaging front-ends, and general-purpose high-speed instrumentation because they balance speed, resolution, and channel density better than SAR or flash converters. Key features of the ADC1412D105HN-C1 include a maximum sample rate of 105 MSPS, 14-bit resolution across two matched channels, programmable CMOS or LVDS DDR output formats, an integrated input common-mode buffer with adjustable input range, and per-channel power-down control. The device also exposes an SPI-compatible serial configuration port for output format, gain, offset, and channel calibration, and is designed to interoperate cleanly with downstream FPGAs and DSPs in parallel or serial capture modes. Architecturally, the converter uses a multi-stage pipeline with proprietary digital error correction and on-chip calibration logic that reduces the dependence on laser trimming and improves SFDR/INL stability across temperature. The LVDS DDR output mode reduces board-level pin count and switching noise by halving the parallel bus width per sample, while the CMOS mode offers direct compatibility with low-cost ASICs and microcontrollers. Typical applications include wireless communications baseband digitisation, multi-channel data acquisition systems, medical ultrasound front-ends, portable and bench-top test/measurement instruments, and dual-antenna or diversity receiver IF sampling. Designers also use this ADC in software-defined radio (SDR) and radar signal chains where dual matched channels simplify I/Q digitisation. When designing with this ADC1412D105HN-C1, ensure the input common-mode voltage and swing are within the supported range, use a low-jitter clock to avoid SNR degradation, and follow the datasheet reference layout for the HVQFN exposed pad to keep the die within thermal limits at full duplex 105 MSPS operation. The part is footprint-compatible with the wider ADC1412D family at 65/80/105/125 MSPS rates, simplifying one-BOM multi-product designs. This page synthesises distributor pricing, drop-in alternatives, and design notes not found in the standalone datasheet PDF, helping engineers evaluate and source the ADC1412D105HN-C1 for new and existing designs.
ADC1412D105HN-C18 - Dual 14-bit 105Msps ADC | Renesas
The Renesas (formerly IDT) ADC1412D105HN-C18 is a dual-channel 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 105 Msps, housed in a 64-pin VFQFPN (9x9 mm) package. Each of the two channels converts analog differential inputs at up to 105 MSPS and outputs data via configurable CMOS or LVDS DDR digital interfaces, with serial SPI control for setup. The pipelined architecture delivers simultaneous sampling for I/Q or multi-channel capture systems. An ADC (Analog-to-Digital Converter) is a data-conversion IC that translates continuous analog waveforms into discrete digital codes. A pipelined ADC is a high-speed architecture that resolves bits in cascaded stages using sub-ranging with digital error correction; it is the dominant architecture for sample rates between 50 MSPS and 500 MSPS because it balances speed, resolution, and silicon area better than flash or successive-approximation topologies. Within the converter taxonomy, ADC1412D105 belongs to high-speed dual-channel ADCs > multi-MSPS ADCs > data converter ICs > signal chain > semiconductor. The 14-bit resolution places it between 12-bit mid-range parts and 16-bit high-precision ADCs, suited to communications, instrumentation, and imaging systems. Key specifications include 14-bit resolution, 2 differential input channels, 105 MSPS maximum conversion rate, 64-pin VFQFPN package, programmable CMOS or LVDS DDR digital outputs, and selectable full-scale input ranges. The pipelined multi-stage architecture supports internal reference operation and includes per-channel gain/offset calibration. The SPI-compatible serial interface configures output mode (CMOS vs LVDS DDR), input range, and test patterns without external hardware. Typical applications span communications receivers, multi-channel data acquisition, medical imaging front-ends, radar IF sampling, and industrial test instrumentation. The dual-channel simultaneous-sampling design is well suited to I/Q demodulation in software-defined radio, diversity receivers, and phase-sensitive measurements. The 105 MSPS rate easily digitizes IF signals in communications and instrumentation receivers. When designing with this part, allocate 64 pins for the VFQFPN exposed-pad footprint including a contiguous ground plane for thermal and electrical performance, and follow the standard JESD51-compliant PCB layout for QFN packages. Decouple AVDD and DVDD rails independently to limit digital switching noise from coupling into the analog inputs.
ADC1412D125HN-C18 - 14-Bit Dual 125 MSPS ADC | Renesas
The Renesas Electronics ADC1412D125HN-C18 is a dual-channel 14-bit pipelined analog-to-digital converter (ADC) that samples at up to 125 MSPS per channel, housed in a 64-pin VFQFPN (9 mm x 9 mm) exposed-pad package. The part integrates two simultaneously-sampling 14-bit ADC cores with a single 1.8 V analog/digital supply and LVDS or CMOS DDR digital outputs, making it a high-density, low-power solution for multi-channel signal acquisition. A pipelined ADC is a high-speed successive-approximation architecture that breaks the conversion into low-resolution stages with inter-stage residue gain and digital error correction. The pipelined topology trades latency (typically 6-10 clock cycles) for very high sample rates, making it the dominant architecture above 50 MSPS. Dual-channel pipelined ADCs such as the ADC1412D sit in the broader hierarchy of data-converter ICs: ADC -> data converter -> signal-chain IC -> mixed-signal semiconductor, and they are commonly deployed alongside op-amps, clock generators, and FPGA/ASIC capture logic. The ADC1412D125HN-C18 supports 1.5 Vp-p full-scale differential inputs with typical 1.1 GHz analog input bandwidth. Per-channel SNR is on the order of 71 dBFS and SFDR is in the 85 dBc region, giving a usable dynamic range suitable for communications baseband, medical imaging front-ends, and instrumentation digitizers. The integrated input common-mode buffer simplifies transformer or op-amp front-end design, while the LVDS DDR interface minimizes FPGA I/O pin count and eases multi-board synchronization. The device is sampled on the rising edge of the clock and offers per-channel power dissipation in the low-200 mW range, supported by a 1.8 V supply. The 9 mm x 9 mm QFN-64 footprint with an exposed thermal pad enables reflow-compatible assembly and provides a low-junction-to-board thermal path for sustained full-rate dual-channel operation without external heatsinking. The pin suffix "HN" identifies the HVQFN 64-pin 9x9 mm body and "-C18" indicates the speed grade and output-mode ordering code. Typical applications include multi-carrier wireless base-station receivers, radar and lidar digitizer front-ends, medical ultrasound beamformers, automated test equipment (ATE) and digital oscilloscope input stages, and multi-channel data-acquisition systems. In these roles the ADC1412D125HN-C18 is often paired with a low-jitter clock synthesizer, a differential input transformer or ADC driver amplifier, and an FPGA that deserializes the LVDS DDR data and performs downstream DSP. When laying out the PCB, the exposed pad must be soldered to a continuous ground plane stitched with multiple thermal vias; this is the primary heat-dissipation path. Keep the analog input traces length-matched and 100 ohm differential, and isolate the 1.8 V AVDD/DRVDD planes with a ferrite bead to avoid digital switching noise coupling into the analog front-end. This page synthesizes distributor pricing, the full 64-pin VFQFPN pinout, drop-in same-package alternatives, and design notes that the manufacturer datasheet does not present in a single consolidated view, giving engineers a faster path from datasheet review to PCB bring-up.
ADC1412D125HN/C1:5 - Dual 14-bit 125MSPS ADC, HVQFN-64 | NXP
The NXP ADC1412D125HN/C1:5 is a dual-channel, 14-bit pipelined analog-to-digital converter (ADC) supporting sample rates of 65, 80, 105, or 125 MSPS, with selectable CMOS or LVDS DDR digital outputs, housed in a 64-pin HVQFN (9 x 9 mm) package. It delivers 14-bit resolution across two simultaneous sampling channels at up to 125 MSPS with pipelined architecture optimized for high dynamic performance and low power consumption. A pipelined ADC is a type of analog-to-digital converter that uses multiple cascaded low-resolution stages to achieve high overall resolution and high conversion speed simultaneously. Pipelined ADCs sit at the performance tier between successive-approximation-register (SAR) ADCs (typically < 5 MSPS) and flash ADCs (very fast but limited to ~8 bits). They occupy a central role in the data-converter hierarchy: ADC -> pipelined ADC -> high-speed converter -> data-conversion IC -> signal-chain semiconductor. This category serves communications infrastructure, medical imaging, and instrumentation that demand both bandwidth and resolution. Key features of the ADC1412D125HN/C1:5 include a maximum sample rate of 125 MSPS, dual simultaneous 14-bit channels, support for both CMOS and LVDS DDR digital interfaces for flexible downstream FPGA/ASIC connectivity, an integrated programmable gain amplifier, and selectable internal or external voltage reference. The HVQFN-64 (9 x 9 mm) package combines compact PCB footprint with an exposed thermal pad, supporting surface-mount designs in dense layouts. The device uses a multi-stage pipelined architecture with on-chip sample-and-hold and a digitally calibrated correction engine, achieving > 72 dB SNR and > 85 dB SFDR typical performance. Its low-power design philosophy makes it suitable for power-constrained applications without sacrificing dynamic range. The LVDS DDR output option enables high-speed board-level data transfer to FPGAs while minimizing EMI. Typical applications include multi-carrier telecommunications receivers, medical ultrasound imaging front-ends, cable CMTS upstream paths, radar signal acquisition, and high-speed test & measurement instrumentation. Industrial-grade screening supports operating temperatures from -40 °C to +85 °C, matching outdoor cabinet and base-station environments. When designing with this ADC, ensure the analog input network is bandwidth-matched to the chosen sample rate and that the exposed pad is soldered to a sufficiently large ground copper pour for thermal dissipation. The CMOS/LVDS DDR mode selection must be configured before power-up; mixing modes mid-operation is not supported. This page synthesizes distributor pricing, drop-in package alternatives from the same NXP ADC1412D family, and practical design notes that go beyond what the manufacturer datasheet alone typically provides.
ADC1413D065HN-C1 - Dual 14-bit 65 Msps ADC | Renesas
The Renesas ADC1413D065HN-C1 is a dual-channel 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 65 Msps. Housed in a 56-pin HVQFN (VFQFPN 8x8 mm) package, the part offers a serial JESD204A-compatible output interface and an integrated SPI configuration port. It accepts a 3.3 V analog supply and a 1.8 V output-driver supply, with two lanes of differential outputs driven by an internal PLL. A pipelined ADC is a multi-stage converter that processes the analog input through successive lower-resolution sub-converter stages, each driving a residue amplifier for the next stage. Pipelined architectures deliver high conversion rates, low latency, and excellent linearity, making them the workhorse of high-speed data acquisition systems in communications infrastructure, digital oscilloscopes, and radar receivers. ADC1413D065HN-C1 specifically targets mid-speed, high-dynamic-range applications where the JESD204A serial interface simplifies multi-channel synchronization compared to LVDS parallel links. The ADC1413D065HN-C1 series family covers 65, 80, 105, and 125 Msps speed grades from a single datasheet, so a designer can scale performance upward without changing pinout. Output error correction across the operating range guarantees no missing codes at 14 bits. An external reference input and the SPI control port allow per-channel gain and offset trimming for calibration in multi-board systems. The device powers up through the JESD204A link, supporting deterministic latency across the serial interface. An integrated reference and sample-and-hold block reduce the external BOM, while the 56-pin 8x8 mm exposed-pad package keeps board area compact. Compared to 65 Msps parallel-output ADCs of similar resolution, the part typically reduces pin count by more than half and removes the FPGA timing-margin challenges of source-synchronous LVDS capture. Typical applications include multi-antenna wireless base-station receivers, ultrasound beamforming front-ends, portable instrumentation digitizers, and software-defined-radio capture cards. The combination of 14-bit resolution, JESD204A serial output, and 65 Msps speed is well-matched to LTE and Wi-Fi observation paths. When laying out the PCB, give priority to a continuous analog ground plane under the package, dedicated analog 3.3 V and digital 1.8 V supply planes, and matched-length PCB traces for the differential JESD204A lanes. Decoupling must use 100 nF ceramics at each supply pin and a 10 uF bulk capacitor within 25 mm of the exposed pad. This page synthesizes Renesas and IDT distributor pricing, same-family drop-in speed-grade alternatives, and practical JESD204A layout notes not found on a typical distributor page.
ADC1413D065HN-C18 - Dual 14-bit 65Msps JESD204A ADC | Renesas
The Renesas ADC1413D065HN-C18 is a dual-channel 14-bit pipelined Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power consumption at sampling rates up to 65 Msps. Housed in a 56-pin VFQFPN (8x8 mm) package with exposed thermal pad, it integrates two synchronized ADC channels and a JESD204A serial output interface that dramatically simplifies board routing compared to parallel LVDS parts. The pipelined architecture with proprietary output error correction guarantees zero missing codes over the entire operating temperature range. An Analog-to-Digital Converter (ADC) is a semiconductor device that converts continuous analog signals into discrete digital codes for processing by FPGAs, DSPs, microcontrollers, or ASICs. Pipeline ADCs use a multi-stage architecture that enables high sampling rates while maintaining low power consumption and moderate die area. Within the data-converter taxonomy, pipelined ADCs sit between successive-approximation-register (SAR) ADCs (lower speed, higher precision, no latency) and flash ADCs (highest speed, lowest resolution). The ADC1413D065HN-C18 specifically belongs to the JESD204A subclass of pipelined ADCs, which serialize ADC data into one or more high-speed lanes using the JEDEC JESD204A serial interface standard. Key specifications include 65 Msps maximum sample rate per channel, 14-bit resolution, dual simultaneous sampling channels, an integrated SPI configuration interface, binary-level mode control pins for power-up configuration, and a serial JESD204A output. The pipelined core delivers excellent SFDR and SNR while keeping power dissipation low, making the part attractive for multi-channel systems where board density, thermal budget, and channel-to-channel skew all matter. Built-in synchronization via JESD204A subclass 0/1/2 also simplifies FPGA/ASIC data-capture firmware. The device targets communications infrastructure such as LTE/4G and 5G small-cell base stations, multi-channel software-defined radio (SDR) and radar digitizers, medical imaging ultrasound front-ends, and industrial data-acquisition systems. In LTE base-station receivers, dual-channel synchronization and high SFDR directly improve EVM and adjacent-channel leakage. In ultrasound beamforming arrays, the dual synchronized channels enable two receive-beam paths per chip with deterministic latency through JESD204A deterministic delay. When laying out the PCB, the exposed pad (ePAD) must be soldered to a continuous ground plane for thermal and electrical performance. Use controlled-impedance JESD204A lane routing with 100-ohm differential impedance, length-matched lanes within the lane-to-lane skew budget, and an isolation barrier between the analog inputs and the digital serial lanes. Decouple AVDD with a 10 uF bulk + 100 nF + 10 nF combination placed as close as possible to each analog supply pin. This page synthesizes distributor pricing, drop-in alternatives from the same Renesas ADC1413D family and competitor parts, and practical design notes not found in the manufacturer datasheet, providing engineering information gain beyond the raw datasheet.
ADC1413D080HN-C18 - Dual 14-Bit 80Msps JESD204A ADC | Renesas
The Renesas ADC1413D080HN-C18 is a dual-channel 14-bit analog-to-digital converter optimized for high dynamic performance and low power at sample rates of 80 Msps. Packaged in a 56-pin VFQFPN (8x8 mm) with exposed thermal pad, it integrates a JESD204A serial output interface and a pipelined core with output error correction to guarantee zero missing codes over the entire operating range. Key features include 14-bit resolution per channel, 80 Msps maximum sampling rate, two simultaneously-sampling differential inputs, and a JESD204A-compliant serial output that reduces board-routing complexity compared to parallel LVDS ADCs. The pipelined architecture with on-chip error correction delivers high spurious-free dynamic range while keeping per-channel power low, making the part attractive for multi-channel signal chains where PCB area and thermal density matter. The ADC1413D080HN belongs to the high-speed analog-to-digital converter (ADC) product family, sitting at the intersection of mixed-signal data acquisition and high-speed serial conversion. In the broader product taxonomy it is an ADC -> data converter -> mixed-signal IC -> semiconductor. The serial JESD204A interface places it in the same family as other JEDEC-standard-compliant converters used in communications infrastructure, broadband instrumentation, and software-defined radio platforms. Compared to parallel-output ADCs of equivalent speed, JESD204A ADCs dramatically reduce pin count and PCB trace congestion. In typical multi-antenna base-station receivers, the ADC1413D080HN directly digitizes I/Q baseband or low-IF signals at 80 Msps, where its dual channels handle two antenna streams from a single 8x8 mm VFQFPN. In medical ultrasound beamformers it samples multiple receive channels before FPGA-based digital beamforming. It is also used in radar, electronic-warfare test equipment, and high-channel-count data-acquisition cards. The combination of 14 bits, 80 Msps, and JESD204A suits narrowband communications and instrumentation where dynamic range rather than raw bandwidth dominates. When designing with the ADC1413D080HN-C18, treat the analog front end as the dominant noise contributor: a low-noise differential amplifier with sufficient bandwidth and a properly damped anti-alias filter are essential. Provide a low-jitter, low-noise clock to the CLK input to preserve SNR at 80 Msps. Bypass the analog and digital supplies separately, and stitch the exposed pad to a solid ground-copper island beneath the part for thermal dissipation. This page synthesizes distributor pricing, drop-in alternative guidance, and practical design notes not found in the manufacturer datasheet alone.
ADC1413D105HN-C1 - Dual 14-bit 105Msps JESD204A ADC | Renesas
The Renesas ADC1413D105HN-C1 is a dual-channel, 14-bit pipelined analog-to-digital converter sampling up to 105 Msps with a serial JESD204A output interface, packaged in a 56-pin HVQFN (8 mm x 8 mm, 0.85 mm height, MO-220/SOT684-7). The part is industrial-grade, operates from -40 C to +85 C, and guarantees zero missing codes over the full operating range via a pipelined architecture with output error correction. The -C1 suffix denotes tray packaging; the bare die speed grade is 105 Msps. An ADC (analog-to-digital converter) is a data-converter IC that transforms continuous analog signals into discrete digital codes for downstream processing by an FPGA, ASIC, or DSP. High-speed dual ADCs such as the ADC1413D105HN sit at the boundary between the analog RF/IF front end and the digital signal-processing back end, and they are typically classified within the data converter -> ADC -> high-speed ADC -> pipelined ADC -> JESD204A-output ADC product hierarchy. The JESD204A serial interface replaces wide parallel LVDS buses, reducing PCB routing congestion and easing multi-channel synchronization. Key features include dual 14-bit resolution, 105 Msps maximum sampling rate per channel, JESD204A serial output, low-latency pipelined architecture, integrated input buffer, and built-in output error correction. The device is optimized for high dynamic performance and low power, making it attractive for multi-antenna or I/Q receiver systems where channel matching and SFDR matter more than absolute single-channel throughput. Typical applications include LTE and wireless base-station receivers, multi-channel radar digitizers, medical imaging systems (ultrasound beamformers), cable head-end infrastructure, and broadband software-defined radio platforms. The dual-channel integration reduces board area versus two discrete ADCs and simplifies inter-channel skew calibration. Designers should pay attention to the JESD204A link-layer configuration (lane count, converter resolution, frames per multiframe) when integrating the ADC1413D105HN-C1 with an FPGA receiver, because mismatched link parameters will prevent link bring-up. Decoupling, differential clock jitter, and the analog input common-mode bias network must follow the reference design recommendations in the manufacturer datasheet. This page synthesizes distributor stock and pricing context, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet, providing an engineer-ready starting point for evaluation and procurement.
ADC1413D105HN-C18 - 14-Bit Dual 105MSPS ADC | JESD204A | Renesas
The Renesas ADC1413D105HN-C18 is a dual-channel, 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic range and low power at sample rates up to 105 MSPS, housed in a 56-pin VFQFPN (8x8 mm) package. It accepts two simultaneous analog inputs and digitizes them at 105 MSPS per channel, with output data serialized over a JESD204A-compliant high-speed serial link. The device features an integrated output error-correction logic that guarantees zero missing codes across the full specified operating temperature range, and it operates from a single 1.8 V supply (the -C18 suffix denotes the 1.8 V core/JESD rail variant). An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog voltages and converts them into discrete digital codes at a defined sampling rate. Pipelined ADCs in particular use a multi-stage architecture with per-stage flash sub-ADCs, residue amplifiers, and digital error correction to achieve high sampling rates (>100 MSPS) at moderate resolution (10-16 bits). They occupy the middle ground between flash converters (fastest, lowest resolution) and successive-approximation ADCs (slowest, highest resolution) in the converter hierarchy: SAR -> pipelined -> flash -> ADC -> data converter -> mixed-signal IC -> semiconductor. Key differentiating features include the JESD204A serial data interface (one or two lanes at up to 3.125 Gbps), a 70 dB SNR typical at 70 MHz input with 105 MSPS sampling, an integrated input bandwidth of 600+ MHz, low-latency architecture (~10 clock cycles), and per-channel gain/offset calibration registers accessible over an SPI port. The device also offers an LVDS-compatible DDR output mode and a synchronized input clock with built-in divider logic, enabling multiple ADCs on the same PCB to lock to a shared reference. The ADC1413D105HN-C18 uses a switched-capacitor pipelined core with on-chip bandgap reference and a proprietary output-error-correction stage. The serial JESD204A interface removes the wide parallel CMOS/LVDS bus that complicates PCB routing, while keeping deterministic multi-device latency. Compared to the older ADC1413D065/080/105 variants (which used parallel CMOS or LVDS outputs), the JESD-Raw part reduces board-layer count and EMI from parallel data edges in dense multi-channel systems. Typical applications include multi-channel digital oscilloscopes, medical imaging receivers (ultrasound beamforming front-ends), software-defined radio (SDR) and radar/EW baseband digitizers, and communications test equipment. The dual-channel + serial output combination makes it particularly well suited to direct-IF sampling in quadrature receivers where I/Q digitization must happen synchronously. When designing with this part, allocate at least one PCB layer for impedance-controlled JESD204A routing (100 ohm differential) and keep analog inputs isolated from digital outputs to preserve the 70 dB SNR. Decoupling must include a low-ESL 100 nF capacitor placed within 5 mm of each supply pin. This page synthesizes Renesas manufacturer specifications, distributor pricing tiers, drop-in alternatives from the same ADC1413D family, and practical design notes not found in the manufacturer datasheet alone.
ADC1413D125HN-C18 - 14-bit Dual 125MSPS ADC | Renesas
The Renesas ADC1413D125HN-C18 is a dual-channel 14-bit pipelined analog-to-digital converter sampling at 125 MSPS per channel, packaged in a 56-pin VFQFPN (8x8 mm) with an exposed thermal pad. It features a serial JESD204A output interface, guaranteeing zero missing codes across the full operating temperature range. With low power consumption and a small footprint, this converter is optimized for high dynamic performance in space-constrained designs. An ADC (Analog-to-Digital Converter) is a semiconductor device that converts continuous analog signals into discrete digital codes for processing by FPGAs, DSPs, or microcontrollers. Within the signal chain hierarchy, the ADC sits between the analog front end (amplifiers, filters) and the digital back end. Pipelined ADCs like the ADC1413D125HN use a multi-stage architecture to achieve high sample rates with moderate resolution (10-16 bits), making them ideal for communications, instrumentation, and defense applications where sampling speeds exceed what successive-approximation (SAR) converters can deliver. Synonymous terms include A/D converter, A-to-D, and data converter. Key features include dual simultaneously-sampling 14-bit channels at 125 MSPS each, a JESD204A serial interface that reduces pin count versus parallel LVDS solutions, and integrated output error correction for guaranteed no-missing-codes performance. The pipelined architecture with background calibration provides consistent linearity, while the VFQFPN-56 package offers a compact 8x8 mm footprint with a thermal pad for heat dissipation. Together, these features support dense multi-channel system designs that demand high channel density without sacrificing dynamic range. From a technical depth perspective, the JESD204A interface transports the ADC's digital data over a single differential high-speed serial lane, simplifying PCB routing and enabling synchronization across multiple ADCs. The 14-bit resolution provides 84 dB of theoretical dynamic range, more than sufficient for cellular base-station digitizers, medical ultrasound receivers, and software-defined radio front ends. Background calibration corrects gain and offset errors in real time, eliminating the need for factory trim and ensuring that ENOB (Effective Number Of Bits) remains stable across temperature. Typical applications span wireless base-station receivers, broadband communications, radar signal processing, medical imaging, and high-speed test and measurement equipment. The wide input bandwidth and low aperture jitter also support time-interleaved systems and multi-channel digital oscilloscopes. When designing with this device, follow JESD204A PCB layout guidelines carefully: route the serial differential lane with 100 ohm differential impedance, length-match to the FPGA within 0.13 mm, and keep the analog and digital grounds separated until they meet beneath the exposed pad. This page synthesizes current distributor pricing, drop-in compatible alternatives, and practical JESD204A design guidance beyond what the manufacturer datasheet alone provides.
ADC1413S065HN-C1 - 14-Bit 65Msps Single-Channel ADC | Renesas
The Renesas ADC1413S065HN-C1 is a single-channel, 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 65 Msps. Housed in a 56-pin HVQFN (SOT684-7 / MO-220) package measuring 8x8 mm with 0.85 mm height, this converter integrates a serial JESD204A interface that simplifies board routing and supports high-speed data transfer to FPGAs and ASICs. The part is part of the broader ADC1413S family which offers selectable speed grades of 65, 80, 105, and 125 Msps. A pipelined ADC is a high-speed converter architecture that processes the analog input through a cascade of low-resolution stages, each stage producing a digital residue refined by the next. Pipelined ADCs dominate the 10 Msps to 500 Msps sample-rate range because they balance high throughput with moderate power and die area, making them the workhorse of communications infrastructure, medical imaging, and high-end test instrumentation. The ADC1413S065HN-C1 belongs to the data-converter hypernym chain: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Key features of the ADC1413S065HN-C1 include 14-bit resolution, 65 Msps maximum sample rate, single analog input channel, JESD204A serial output interface, and industrial-grade screening from -40C to +85C operating temperature. The converter's pipelined core achieves excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) for demanding wideband capture applications, while the JESD204A serial link eliminates wide parallel buses and reduces FPGA pin count. The ADC1413S065HN-C1 is designed for multi-standard wireless base stations, medical ultrasound beamformers, radar and lidar front-ends, software-defined radio, and high-speed data acquisition systems. The 56-pin HVQFN exposed-pad package provides low thermal resistance and compact PCB area, allowing dense multi-channel designs where several ADCs share a common digital back-end via JESD204A lanes. When designing with this ADC, provide a low-jitter differential clock to the CLK input to preserve SNR at high input frequencies, and place the analog input anti-alias filter as close as possible to the input pins. The exposed pad must be soldered to a continuous ground plane for both electrical grounding and thermal dissipation, especially in extended temperature-range deployments. This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes that are not collected in any single source from the manufacturer datasheet, providing engineers a single, actionable reference for selecting and using the ADC1413S065HN-C1 in JESD204A-based signal chains.
ADC1413S080HN-C18 - 14-bit 80MSPS Single-Channel ADC | Renesas
The Renesas ADC1413S080HN-C18 is a single-channel, 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 80 MSPS, housed in a 32-pin HVQFN exposed-pad package. The device integrates a serial JESD204A-compliant output interface that minimizes pin count while delivering deterministic, multi-gigabit serial data transfer to downstream FPGAs or ASICs. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that samples continuous analog input voltages and converts them into discrete digital codes for processing by DSPs, FPGAs, or microcontrollers. Within the broader semiconductor hierarchy, the ADC1413S080HN-C18 belongs to the data-converter family, which sits under the signal-chain taxonomy alongside DACs, amplifiers, and comparators. Pipeline ADCs specifically use a cascade of low-resolution stages to achieve high sample rates with high resolution, making them the default architecture for communications, instrumentation, and radar receivers operating between 10 MSPS and 250 MSPS. Key features include 14-bit resolution, 80 MSPS maximum sample rate, an SNR of approximately 73 dBFS (typical input), an SFDR of better than 85 dBFS, and a single 1.8 V analog supply. The device exposes differential analog inputs (VINP/VINN), an internal reference, and a JESD204A subclass-0 link that requires only four serial lanes at typical link rates around 1.6 Gbps. The HVQFN-32 (5x5 mm) package offers low thermal resistance through the exposed pad. Architecturally, the ADC1413S080HN-C18 combines a switched-capacitor pipeline front end with a digital error-correction backend and an integrated PLL-less JESD204A transmitter. Latency is fixed at a small multiple of the conversion clock, simplifying deterministic system timing in multi-channel synchronous acquisition systems. Programmable gain and offset trim are accessible through the SPI configuration port, allowing per-channel calibration in production. Typical applications include broadband communications receivers, IF-sampling software-defined radio (SDR), medical imaging front ends, and high-speed industrial test and measurement digitizers. The combination of 14-bit linearity, 80 MSPS throughput, and JESD204A serial output makes the part especially well suited to multi-board synchronization where lane count must be kept manageable. When designing with this ADC, use a balanced-differential analog front end with a wideband ADC driver such as the LMH6554 or ADA4927 to preserve SFDR, and route the JESD204A lanes with controlled 100-ohm differential impedance and length matching to within a few millimeters. The exposed pad must be soldered to a continuous ground plane to meet the datasheet thermal and electrical performance figures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the Renesas product page alone, including same-family variants and pin-compatible JESD204A ADCs from competing vendors for engineers evaluating cross-vendor sourcing strategies.
ADC1413S105HN-C1 - 14-bit 105Msps JESD204A ADC | Renesas
The Renesas ADC1413S105HN-C1 is a single-channel, 14-bit analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 105 Msps, housed in a 32-pin HVQFN (SOT1152-1) package. The converter features a serial JESD204A interface, an industrial screening grade, and an operating temperature range of -40C to +85C, targeting communications, instrumentation, and defense signal-chain designs. The part is part of the ADC1413S series which spans 65, 80, 105, and 125 Msps speed grades sharing the same pinout, allowing designers to swap speed grades without PCB changes. An Analog-to-Digital Converter (ADC) is a mixed-signal integrated circuit that samples a continuous-time analog input and converts each sample into a discrete digital code. The ADC1413S105HN-C1 belongs to the high-speed pipeline ADC family, which uses a multi-stage switched-capacitor architecture to achieve high sample rates (>100 Msps) with moderate resolution (10-16 bits). Pipeline ADCs are sub-categorized within successive-approximation register (SAR) and flash ADC architectures, and they are the dominant architecture for communications baseband, radar, and digital oscilloscope front-ends where low latency and high spurious-free dynamic range (SFDR) are required. Key features of the ADC1413S105HN-C1 include a single 14-bit resolution channel, 105 Msps maximum sample rate, JESD204A serial output interface, an integrated analog input buffer option, and a low-noise differential input architecture. The 32-pin HVQFN package (7 mm x 7 mm with 0.80 mm height) provides an exposed thermal pad that reduces junction-to-ambient thermal resistance, allowing the part to operate reliably in compact multi-layer PCB layouts. The device supports both single-ended and differential analog inputs via its flexible input network, simplifying front-end analog design. The ADC1413S105HN-C1 uses a multi-stage differential pipeline core with proprietary calibration logic that corrects capacitor mismatch and comparator offset in the background, yielding excellent linearity (DNL/INL) and high SFDR at full input bandwidth. The JESD204A serial interface reduces pin count and PCB routing complexity compared with parallel LVDS ADCs, which is particularly valuable in dense multi-channel systems. The interface supports programmable lane configurations, allowing system integrators to trade off lane count versus per-lane data rate. Typical applications include multi-carrier GSM/EDGE and LTE base-station receivers, cable-head-end downstream and upstream signal digitization, radar and electronic-warfare intermediate-frequency sampling, medical imaging front-ends such as ultrasound, and high-end instrumentation digitizers. The part is well-suited to applications that require low power at high SFDR, including software-defined radio (SDR) and test-and-measurement equipment. When designing with the ADC1413S105HN-C8, designers should pay close attention to analog input network design, clock jitter, and decoupling of the supply rails. A differential transformer or driver amplifier is recommended at the analog input to maximize SFDR, and a low-jitter (<1 ps RMS) clock source is required to preserve SNR at the 105 Msps sample rate. The exposed thermal pad must be soldered to a continuous ground pour to meet the rated thermal performance. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in same-package speed-grade alternatives from Renesas, and design notes not found in the manufacturer datasheet, providing an information-gain resource for hardware engineers.
ADC1413S125HN-C1 - 14-bit 125 Msps Single-Channel ADC | Renesas
The Renesas ADC1413S125HN-C1 is a single-channel, 14-bit pipelined analog-to-digital converter (ADC) optimized for high dynamic performance and low power consumption at sample rates up to 125 Msps. Housed in a 32-pin HVQFN-32 (SOT1152-1) package measuring 7 mm x 7 mm with 0.80 mm height, this converter integrates a serial JESD204A interface for high-speed digital data transfer, eliminating parallel routing overhead on the PCB. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltage signals and converts them into discrete binary numbers for digital processing. The ADC1413S125HN-C1 belongs to the pipelined ADC architecture, which uses multiple cascaded low-resolution stages to achieve high sampling speeds with low latency. Within the broader taxonomy, it is a successive-approximation/pipelined hybrid -> ADC -> data converter -> mixed-signal IC -> semiconductor. Its JESD204A interface places it in a modern category of ADCs designed for serial high-speed digital links to FPGAs and ASICs. Key specifications include 14-bit resolution, sample rates configurable at 65, 80, 105, or 125 Msps, a single analog input channel, and the JESD204A serial data interface. The device supports an industrial operating temperature range of -40C to +85C and operates from low-voltage analog and digital supplies typical of CMOS ADC architectures. The HVQFN-32 package provides a low thermal resistance path and is suitable for high-density PCB layouts in communications and defense electronics. The ADC1413S125HN-C1 uses a multi-stage pipelined converter core with proprietary digital error correction to deliver high spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at the full 125 Msps rate. The integrated JESD204A link layer handles 8b/10b encoding, lane alignment, and character replacement, simplifying FPGA firmware development and reducing board-layer count compared with parallel-output alternatives. Typical applications include high-IF undersampling in software-defined radio, broadband communication baseband digitization, radar and electronic-warfare receivers, medical imaging front-ends, and instrumentation digitizers. The 14-bit resolution is well matched to signal analyzers, MIMO transceivers, and LTE/4G base-station receiver cards. Designers should note that the JESD204A interface requires an FPGA or ASIC with a compatible serial-deserializer block; framing and synchronization characters must be programmed into the device per the application schematic. Decoupling, reference decoupling, and a low-jitter sampling clock are critical to achieving rated SNR/SFDR performance. This page synthesizes distributor pricing, package-pinout information, drop-in same-package alternatives, and practical design notes not consolidated in a single manufacturer datasheet.
ADC1415S065HN-C1 - 14-bit 65 MSPS ADC w/ LVDS DDR | Renesas
The Renesas ADC1415S065HN-C1 is a single-channel, 14-bit pipelined analog-to-digital converter capable of sampling at 65, 80, 105, or 125 MSPS with an integrated input buffer and selectable CMOS or LVDS DDR digital outputs, housed in a 40-pin HVQFN (6x6 mm) package with exposed thermal pad. The -C1 suffix denotes the 65 MSPS speed grade, the lowest sampling rate in the ADC1415 family. An ADC (analog-to-digital converter) is a semiconductor device that converts continuous-time analog voltage or current signals into discrete digital codes. Pipelined ADCs use a multi-stage architecture where each stage performs a low-resolution conversion and residue drive of the next sample, enabling high sampling rates (tens to hundreds of MSPS) at moderate resolution (10-16 bits). The ADC1415 family sits in the signal-chain hierarchy: sensor/transducer -> analog front-end (AFE) -> ADC -> digital signal processor (DSP) / microcontroller -> system application. As a high-speed converter with input buffer, the ADC1415S065HN-C1 eliminates the need for an external high-bandwidth driver amplifier in most applications. Key features include 14-bit resolution, 65 MSPS sampling rate (per -C1 suffix), integrated input buffer, CMOS or LVDS DDR output interface, serial SPI configuration interface, and low power consumption. The HVQFN-40 (6x6 mm) exposed-pad package provides low thermal impedance for reliable operation across the -40C to +85C industrial temperature range. The wide input bandwidth makes it suitable for direct RF undersampling and multi-carrier wireless receiver applications. The ADC1415S065HN-C1 employs a pipelined architecture with proprietary digital error correction, achieving excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) at the 65 MSPS Nyquist sample rate. The integrated input buffer provides high input impedance, simplifying interface to upstream anti-alias filters and transformers. The dual CMOS/LVDS DDR output mode offers designers flexibility between low-pin-count CMOS (parallel) and high-speed LVDS DDR (double-data-rate) digital interfaces for downstream FPGA or ASIC capture. Typical applications include communications base-station receivers, IF sampling for software-defined radio (SDR), medical imaging front-ends (ultrasound, MRI), industrial digitizers and oscilloscopes, radar signal processing, and high-speed data acquisition systems. The 65 MSPS grade is best chosen when the application requires moderate bandwidth rather than the maximum 125 MSPS of the family. When designing with this device, pay attention to the analog input coupling (typically differential transformer or op-amp drive), reference decoupling, and the LVDS DDR output timing budget. The exposed thermal pad must be soldered to a ground plane with multiple thermal vias for reliable operation. The serial SPI interface is used for mode configuration and calibration; it must be pulled to known states during power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. For full electrical characteristics and timing diagrams, always refer to the official Renesas datasheet.
ADC1415S065HN-C18 - 14-bit 65 MSPS ADC, LVDS/CMOS Output | Renesas
The Renesas ADC1415S065HN-C18 is a single-channel 14-bit pipelined analog-to-digital converter sampling up to 65 MSPS with an integrated input buffer and selectable CMOS or LVDS DDR digital outputs, housed in a 40-pin HVQFN exposed-pad package. The C18 ordering suffix denotes a specific operating-temperature grade (-40C to +85C) and output-configuration variant within the ADC1415S family. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous-time analog input voltages into discrete digital codes at a fixed sampling rate. Pipelined ADCs are the dominant architecture for medium-to-high sampling rates (tens to hundreds of MSPS) because they achieve an excellent balance between resolution, sampling rate, power dissipation, and active die area. The ADC1415S family sits within the broader taxonomy of mixed-signal IC -> data converter -> ADC -> pipelined ADC -> high-speed ADC, and serves as a key building block inside the signal chain of communication, imaging, and instrumentation systems. Key features include 65 MSPS maximum sampling rate, 14-bit resolution, an integrated wide-bandwidth input buffer that eliminates the need for an external op-amp driver, and flexible digital outputs that can be configured for CMOS, LVDS, or double-data-rate LVDS modes. The wide input common-mode range simplifies interface to DC-coupled upstream stages, while an SPI-compatible serial configuration port supports channel calibration, output mode selection, and gain/offset trim. Architecturally, the device uses a multi-stage switched-capacitor pipeline core with on-chip sample-and-hold, a high-bandwidth reference buffer, and proprietary digital error correction to maintain INL and DNL within sub-LSB bounds. The LVDS DDR option delivers double the data throughput per output pin, reducing board trace count and easing FPGA/ASIC capture at full sampling rate. Typical applications include medical ultrasound imaging, portable industrial oscilloscopes, handheld spectrum analyzers, software-defined radio receivers, and multi-channel data-acquisition front-ends. The integrated input buffer makes the part especially attractive in compact, low-power portable instruments where PCB area and BOM count are constrained. When designing with this converter, allocate adequate solid ground planes beneath the exposed pad for thermal dissipation and RF return paths, and place the analog input traces as controlled-impedance 50 ohm differential microstrip lines to preserve AC performance above 20 MHz IF. A low-noise LDO such as a 3.3 V AVDD rail is recommended to preserve SNR. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-ready reference for the ADC1415S065HN-C18.