Circuitos Integrados

LIFCL-40-9MG289C

LIFCL-40-9MG289C - CrossLink-NX 39K LUT FPGA, 289-TFBGA | Lattice

The Lattice LIFCL-40-9MG289C is a CrossLink-NX family field-programmable gate array (FPGA) built on the Lattice Nexus platform, delivering 39000 logic elements, 1548288 bits of embedded memory, and 180 user I/O in a 289-ball TFBGA (CSBGA) package. The part integrates 2.5 Gbps MIPI D-PHY hard IP cores targeting embedded vision bridging and processing applications, while a commercial temperature grade (-9) supports 0C to +85C operation. What is a CrossLink-NX FPGA? An FPGA (Field Programmable Gate Array) is a semiconductor device whose logic fabric, interconnect, and I/O can be reconfigured after manufacturing by the customer. The CrossLink-NX family belongs to the broader category of programmable logic devices (PLDs), which also includes CPLDs. FPGAs sit within the integrated circuit taxonomy as follows: FPGA -> programmable logic -> logic IC -> integrated circuit. CrossLink-NX specifically targets low-power embedded vision bridging, providing hard MIPI D-PHY/CSI-2 cores, hardened memory controllers, and a high-performance fabric for sensor aggregation. Key features include up to 75% lower power compared to similar FPGAs in its class, 2.5G MIPI D-PHY/CSI-2 hard cores enabling direct connection to image sensors and displays, embedded block RAM, distributed SRAM, and on-chip DSP slices. The Nexus platform also provides high reliability for mission-critical applications including automotive and industrial segments. The architecture combines a small-form-factor 289-ball TFBGA package with hardened I/O, allowing PCB designs to keep sensor and display trace lengths short. Designers benefit from Lattice Radiant software support and pre-built IP libraries for MIPI bridging, display controllers, and image signal processing pipelines. Typical applications include embedded vision bridging for camera sensors, AI inference at the edge, machine vision in industrial automation, AR/VR head-mounted displays, and video aggregation/duplication for surveillance and automotive infotainment. When designing with this part, ensure PCB layout follows the BGA escape pattern documented in the Lattice hardware manual and that decoupling capacitors are placed directly under the package balls for clean power delivery to the fabric. This page synthesizes distributor stock, drop-in same-family alternatives, and design notes not found in the manufacturer datasheet. All information reflects availability as of 2026-10-10.

Cotação Contato

LM-555N

LM-555N - Single 555 Timer, 8-PDIP | Texas Instruments

The Texas Instruments LM-555N is a single 555-type timer and oscillator integrated circuit packaged in an 8-pin PDIP. The verified distributor result identifies it as an 8-PDIP device from Harris Corporation, while the official TI family page identifies the LM555 as a highly stable 555 timer. The target MPN is therefore associated with the classic timer functionality, but the supplied data does not provide verified electrical ratings, timing limits, temperature range, or lifecycle details for the exact LM-555N ordering code. What is a 555 timer? A 555 timer is a programmable timer and oscillator integrated circuit used to generate delayed pulses, produce periodic waveforms, debounce inputs, or control relays and indicators. Its internal blocks typically include a voltage reference, comparators, a flip-flop, and a high-current output stage. In astable operation, external resistors and a capacitor set the oscillation period; in monostable operation, an external timing capacitor sets the output pulse width. The verified Harris product description identifies the LM555N for timing-delay and oscillator applications in commercial, industrial, and military equipment. The verified product listing calls it a “555 Type, Timer/Oscillator (Single) IC” and specifies an 8-PDIP package. The official TI product page describes the LM555 family as a highly stable 555 timer and provides family-level documentation, but the supplied material does not expose the exact LM-555N datasheet values. Because the target MPN includes a hyphen while the verified distributor listing uses LM555N, engineers should confirm the exact package, suffix, manufacturer, and electrical limits against the applicable manufacturer documentation before substituting or releasing a production design. The verified result also shows a distributor listing from Rochester Electronics under the Harris Corporation name; Harris Corporation is not in the supplied Manufacturer Reference, so the brand field follows the target context and the official TI source uses Texas Instruments. Typical uses include pulse generation, delay circuits, oscillators, indicator flashing, switch debouncing, and simple industrial control logic. Because the exact pinout, package details, and ratings were not included in the verified data, this page does not infer those values. Check the original LM-555N datasheet and the manufacturer’s current documentation before layout or purchase.

Cotação Contato

LM111

LM111 - High-Speed Differential Comparator | Texas Instruments

The Texas Instruments LM111 is a single high-speed differential voltage comparator with open-collector and open-emitter outputs, designed for operation from a single 5 V supply through dual ±15 V supplies. Its stated maximum input bias current is 300 nA, maximum input offset current is 70 nA, and the device includes strobe capability for controlled comparator operation. The LM111 is packaged in an 8-pin TO-99 style metal can package. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM111 belongs to the comparator category within analog and interface ICs, and its differential inputs make it useful for threshold detection, signal conditioning, timing, and control systems. Unlike an operational amplifier intended primarily for linear amplification, the comparator is optimized for rapid state changes and logic-level output compatibility. The LM111, LM211, and LM311 family is designed around a wide supply-voltage range, including ±15 V operational-amplifier supplies and 5 V logic systems. The output levels are compatible with many TTL and MOS circuits, allowing the LM111 to bridge analog sensing and digital control. Its differential input arrangement supports sensing a small difference between two voltages while presenting a logic result to downstream circuitry. The LM111 family also includes related temperature grades and device variants. Texas Instruments states that the LM111-N has the same pin configuration as the LM106 and LM710, while the LM211-N and LM311-N provide different specified temperature ranges. The exact LM111 pin configuration and electrical limits must be confirmed against the applicable manufacturer datasheet and package variant before production release. Typical applications include line and threshold comparators, pulse and window detection, level translation into TTL or MOS logic, industrial control interfaces, analog signal conditioning, and legacy instrumentation. Because the output is open collector or open emitter, a pull-up or pull-down load resistor is generally required at the output. This architecture can provide wired logic behavior and flexible output interfacing, but it also makes pull-device selection and output speed part of the system design. When selecting a replacement, verify the package, pinout, supply limits, input offset and bias behavior, response time, output topology, and temperature grade. The verified material supports the LM111 identity and family-level characteristics, but it does not provide enough verified information here to reproduce every electrical limit or package drawing. This page therefore distinguishes documented values from parameters requiring confirmation rather than guessing them.

Cotação Contato

LM111-LM211

LM111-LM211 - High-Speed Differential Comparator | Texas Instruments

The Texas Instruments LM111-LM211 is a family designation for single, high-speed differential voltage comparators designed to operate from wide power-supply ranges, including ±15 V operational-amplifier supplies and single +5 V logic supplies. The comparator combines low input current with an open-collector output whose logic levels are compatible with many TTL and MOS circuits. The available ordering variants include LM111, LM211, and LM311 devices documented by the manufacturer under the LM111, LM211, and LM311 differential comparator datasheet. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. In the broader electronics hierarchy, a differential comparator belongs to comparator ICs, analog-to-digital decision interfaces, and signal-conditioning semiconductors. It is commonly used where a sensor, reference voltage, timing ramp, or control signal must be translated into a logic-level event. The LM111, LM211, and LM311 devices are described by Texas Instruments as single high-speed voltage comparators. Their low input currents are useful when the driving source has high impedance or when input bias current could otherwise create measurement errors. The family supports conventional ±15 V supplies and +5 V logic-system operation, making it suitable for legacy analog, control, timing, and industrial interface circuits. Output levels are compatible with most TTL and MOS circuits, although the open-collector output requires an appropriate pull-up arrangement. The LM111, LM211, and LM311 differ primarily in their specified operating-temperature families: TI identifies the LM111-N as specified from −55°C to +125°C, the LM211-N from −25°C to +85°C, and the LM311-N from 0°C to +70°C. The target string LM111-LM211 is therefore a family or ordering designation rather than one uniquely specified package-and-temperature variant. The exact commercial suffix, package, pin configuration, and current availability must be confirmed against the selected manufacturer orderable part. Typical uses include precision voltage thresholding, zero-crossing detection, peak detection, window comparison, pulse timing, sensor interface conditioning, and control logic interfacing. The comparator is placed between a signal source and a downstream TTL or MOS input, with its output configured to drive the receiving device through a suitable pull-up or interface network. Engineers should verify supply polarity, input common-mode limits, output pull-up voltage, switching behavior, and input offset requirements in the manufacturer datasheet before layout release. The key design consideration is that an open-collector comparator is not a push-pull logic driver. The output node floats when the device is off, so the external pull-up resistor, pull-up voltage, load capacitance, and required logic rise time must be selected together. Input filtering and grounding are also important when the comparator is used near precision thresholds or noisy switching nodes. This page distinguishes verified family-level facts from parameters that require a specific package and orderable suffix. This page synthesizes the verified manufacturer and distributor references for the LM111-LM211 family, separates documented family-level capabilities from orderable-device requirements, and highlights the design decisions that determine whether an open-collector comparator is suitable in a given circuit. The alternatives listed here are limited to parts explicitly supported as same-family or comparator cross-reference candidates; exact replacement must be checked against the selected package and suffix.

Cotação Contato

LM111-MDE

LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments

Texas Instruments LM111-MDE is a single, high-speed voltage comparator die designed for operation from wide-range power supplies, including ±15 V operational-amplifier rails and 5 V logic systems. The verified source identifies a single-channel general-purpose comparator with a maximum input offset voltage of 3 mV at ±15 V, maximum quiescent current of 6 mA, and an operating temperature range of -55°C to 125°C. Because the -MDE ordering code denotes a die sale, the component is supplied as an unpackaged semiconductor die rather than a leaded or surface-mount package. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. Within the semiconductor hierarchy, the LM111 belongs to the comparator family, a functional class of analog and mixed-signal ICs used between sensors, transducers, amplifiers, and digital logic. The LM111 family is associated with high-speed decision-making and compatibility with common TTL and MOS output systems, while its open-collector-style output requires an appropriate pull-up arrangement for reliable digital interfacing. The LM111 family provides a single comparator channel and supports a broad supply-voltage range. The verified manufacturer description states that the LM111, LM211, and LM311 are single high-speed voltage comparators. Its output levels are compatible with most TTL and MOS circuits, making the device useful for threshold detection, pulse-width or timing decisions, signal conditioning, and control systems. The maximum input offset voltage of 3 mV at ±15 V defines the comparison accuracy limit, while the 6 mA maximum quiescent current provides a basis for power-supply budgeting. The die-sale format requires special assembly consideration. No package pinout, package dimensions, or exposed thermal pad can be inferred from the verified data because LM111-MDE is sold as a die. A designer must obtain the manufacturer die documentation and assembly requirements before bonding or packaging the device. In particular, do not assume that the die's bond-pad arrangement matches the LM111 leaded-package pinout. The verified source also identifies -55°C to 125°C as the operating temperature range for LM111-MDE, but no die-specific thermal resistance or power rating is provided. Typical uses include high-speed threshold detection, pulse and window comparisons, industrial control interfaces, analog signal conditioning, and logic-level decision circuits. Because the output is intended to interoperate with TTL and MOS systems, the external pull-up network, supply bypassing, input grounding, and output loading are critical. Compared with a finished package, the die-sale device offers sourcing and customization flexibility but requires wafer handling, die attach, wire bonding or other packaging, and application-specific qualification. This product page combines the verified manufacturer and distributor data with practical die-level design guidance, sourcing context, and strict handling of unavailable package information. It is intended to help engineers distinguish the LM111-MDE die sale from packaged LM111 variants and to plan assembly, testing, and supply-chain risk before committing the device to a production design.

Cotação Contato

LM111-MW8

LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments

The Texas Instruments LM111-MW8 is a single high-speed voltage comparator designed for operation from wide-range power supplies, including ±15 V operational-amplifier supplies and 5 V logic systems. The verified product material identifies the LM111 family as a comparator with low input bias current and fast response, while the exact LM111-MW8 package, pinout details, electrical limits, operating temperature range, and orderable package variant are not supplied in the provided data. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a defined threshold. The LM111 belongs to the comparator, analog IC, and signal-conditioning hierarchy rather than the operational-amplifier category, although it can be used in threshold detection, sensing, pulse-width, and control circuits. Its wide supply compatibility allows the same device family to interface with traditional analog rails and lower-voltage logic systems. The LM111 family is specified as a single high-speed voltage comparator. The verified material specifically cites maximum input bias current of 300 nA and maximum input offset current of 70 nA, along with operation from a single 5 V supply. These characteristics are relevant where low input loading and precise threshold behavior are important. The output levels are stated to be compatible with most TTL and MOS circuits, which supports use as a decision element between analog signals and digital control logic. Typical comparator applications include level crossing, overvoltage and undervoltage indication, signal translation, pulse generation, window detection, and interface conditioning. The fast-response description is useful when the comparator must resolve changing waveforms rather than merely provide static threshold monitoring. The published family material also mentions strobe capability, but the exact LM111-MW8 operating conditions and timing values require confirmation in the manufacturer datasheet before design release. Because the provided data does not specify the LM111-MW8 package dimensions, pin names, temperature grade, or exact electrical maximums, those values must be verified against the official Texas Instruments documentation. Do not assume that a similarly named LM111, LM211, or LM311 orderable part is mechanically interchangeable. In particular, LM211 and LM311 are distinct family variants and may have different supply, temperature, or output requirements. This page consolidates the verified Texas Instruments family description, distributor discovery information, and official datasheet references. It also separates confirmed facts from missing LM111-MW8-specific data so engineers can plan sourcing and schematic review without treating unverified package or performance details as specifications.

Cotação Contato

LM201AD

LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics

The STMicroelectronics LM201AD is a single general-purpose operational amplifier supplied in an 8-pin SOIC package. The device is listed as a non-compensated, single operational amplifier with a nominal gain-bandwidth product of 1 MHz, a slew rate of 0.5 V/us, and a dissipation rating of 300 mW. Its stated supply range is plus or minus 5 V to plus or minus 22 V, allowing operation from a 10 V minimum total supply to a 44 V maximum total supply. The LM201AD also provides push-pull output capability according to distributor listings. An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 family is positioned as a general-purpose amplifier rather than a precision micropower device or a high-speed rail-to-rail amplifier. Its non-compensated architecture requires the user to add external compensation when closed-loop stability is needed, making it most suitable for designs in which the engineer selects a specific gain, bandwidth, and phase-margin target. Verified distributor information identifies the LM201AD as a one-amplifier, 8-SOIC device. One distributor listing reports a 1 MHz gain-bandwidth product, while a separate Mouser listing identifies a 3.5 MHz gain-bandwidth figure. These values may reflect different source pages or gain and condition definitions, so the two figures should be confirmed against the exact STMicroelectronics datasheet revision before setting compensation networks or estimating closed-loop bandwidth. Typical uses include general analog signal conditioning, instrumentation interfaces, active filtering, and feedback control in industrial or test equipment where higher supply voltages are acceptable. Because this is a non-compensated amplifier, external compensation components and stability analysis are normally required. The wide plus or minus 22 V capability also makes rail-to-rail input and output operation unlikely, so input and output common-mode and swing limits must be respected. For PCB design, place the amplifier close to feedback and compensation components, keep input nodes away from switching nodes and high-current paths, and provide adequate ground return connectivity for the single-supply return terminal. Decoupling requirements should be confirmed from the manufacturer datasheet rather than inferred from the distributor listings. This page combines verified distributor specifications, package information, cross-reference results, and engineering guidance that are not consolidated in a single manufacturer product listing. Pricing, pin-level data, lifecycle details, and compensation requirements should be verified against the current STMicroelectronics datasheet before production release.

Cotação Contato

LM201AH

LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments

Texas Instruments LM201AH is a single-channel, general-purpose operational amplifier with 1 MHz gain-bandwidth product, 80 dB common-mode rejection ratio, 2 mV input offset voltage, and approximately 1.8 mA supply current, housed in an 8-pin TO-99 hermetic metal-can package. It is intended for instrumentation, analog measurement, filtering, buffering, current sensing, and precision-control circuits operating from -40 °C to +85 °C. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network determines its closed-loop behavior. The LM201AH belongs to the general-purpose operational-amplifier class within the broader amplifier IC and signal-conditioning hierarchy. Its TO-99-8 construction provides a through-hole package option for laboratory, industrial, and legacy instrumentation designs where surface-mount compatibility is not required. The principal performance features include a 1 MHz gain-bandwidth product, 80 dB CMRR, 2 mV input offset voltage, and approximately 1.8 mA operating current. The wide common-mode rejection specification helps reduce unwanted behavior when the amplifier handles small signals superimposed on larger voltage references or sensor outputs. The hermetic TO-99-8 package supports applications requiring a conventional metal-can outline and eight through-hole connections. The LM201A family uses advanced processing to reduce input bias current and temperature drift while retaining the general-purpose characteristics of the earlier LM101A architecture. The device can operate with conventional dual power supplies, making it suitable for signal paths centered around ground. Engineers should nevertheless verify supply-voltage limits, input common-mode range, output swing, compensation requirements, and electrical limits against the manufacturer datasheet before finalizing a design. Typical uses include laboratory instrumentation, analog measurement front ends, active filters, transducers, current-sensing amplifiers, and precision feedback loops. In a filter or amplifier, its 1 MHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected noise-gain configuration. For sensor interfaces, the 80 dB CMRR can help reject common-mode interference, while the 2 mV offset remains an important error term in precision measurements. When designing around the LM201AH, begin by checking the required output swing and input common-mode range at the actual supply voltage. Decoupling should be placed close to the power pins, and the circuit should avoid driving capacitive loads unless stability behavior has been evaluated. Because the exact pin names and electrical limits are not included in the supplied search excerpts, those details should be confirmed in the Texas Instruments LM201A-N documentation before PCB release. This page consolidates the supplied distributor and manufacturer listings with practical selection guidance, package-aware alternatives, comparison parameters, and design cautions. It distinguishes confirmed data from unavailable fields so engineers can verify critical specifications without relying on assumptions.

Cotação Contato

LM201AN

LM201AN - Single Non-Compensated Op Amp | STMicroelectronics

The STMicroelectronics LM201AN is a single, general-purpose, non-compensated bipolar operational amplifier supplied in an 8-pin PDIP package. The confirmed headline characteristics are one amplifier circuit per package, a maximum input offset current of 20 nA over the operating temperature range, and the ability to obtain a slew rate of 10 V/µs when compensated appropriately for the intended circuit. An operational amplifier is a high-gain, differential-input analog building block used to amplify voltage differences, buffer signals, and perform linear operations such as summation, integration, and filtering. The LM201 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Unlike a unity-gain-stable amplifier with internal compensation, the LM201AN is externally compensatable, allowing the circuit designer to select a compensation capacitor suited to the gain, bandwidth, and stability requirements of a particular application. Key features include a low input offset current, a maximum of 20 nA over temperature, and user-selectable compensation. These characteristics are especially relevant to precision analog circuits in which bias-current loading, input balance, and closed-loop stability can materially affect signal integrity. The device is offered as a single amplifier rather than a multi-amplifier package, simplifying board partitioning when separate analog channels require independent compensation or grounding. The non-compensated architecture gives designers control over stability-bandwidth tradeoffs. A compensation capacitor can be omitted or changed for unity-gain service, while larger values or added frequency compensation can improve stability in noise-gain configurations. With proper compensation, the manufacturer-reported capability includes a slew rate of up to 10 V/µs. This makes the LM201AN potentially useful where signal speed matters more than the compactness of a fixed-compensation amplifier. Typical applications include precision instrumentation amplifiers, logarithmic and summing amplifiers, active filters, transducers with relatively high source impedance, laboratory measurement systems, and low-frequency analog signal-conditioning chains. Its external compensation also permits optimization for different closed-loop gains rather than imposing one fixed stability profile across every application. When designing around the LM201AN, select the compensation network for the actual noise gain and verify closed-loop phase margin on the assembled board. Keep input and output return paths short, observe the device's specified supply and common-mode limits, and prototype compensation before high-volume production. External compensation makes the part flexible, but it also places a stability responsibility on the engineer. This page combines confirmed manufacturer-distributor data with clearly marked gaps, practical compensation guidance, package-aware replacement analysis, and procurement information. It distinguishes verified LM201AN characteristics from unverified specifications so engineers can make faster component-selection decisions without mistaking generic amplifier assumptions for device-specific facts.

Cotação Contato

LM211-LM311

LM211-LM311 - Single High-Speed Differential Comparator

The Texas Instruments LM211-LM311 is a family designation for the LM211 and LM311 single high-speed differential comparators, designed for wide supply ranges from single 5 V operation through ±15 V split supplies. The LM211 and LM311 provide low input currents and open-collector outputs intended for driving lamps, relays, and logic-compatible loads. Their differential inputs can accept voltages outside the supply rails, while the output polarity and output-current requirements determine the external pull-up arrangement. A voltage comparator is a semiconductor device that compares two input voltages and switches its output according to their relationship. In the broader IC hierarchy, a comparator belongs to the analog signal-conditioning and interface family, alongside op-amps and logic interfaces. The LM211-LM311 family is useful when a design needs a threshold decision, overvoltage indication, level translation, or relay-drive function rather than linear analog amplification. The verified manufacturer material identifies the devices as single high-speed comparators with low input current. According to the Texas Instruments datasheet material supplied, the output levels are compatible with most TTL and MOS circuits, and the devices are capable of driving lamps or relays. The onsemi material additionally states that the inputs can be isolated from system ground while the output can drive loads referenced to ground, VCC, or VEE. These features support industrial control, instrumentation, and legacy interface designs. The family includes temperature and sourcing differences between LM211 and LM311 variants. The supplied Mouser datasheet excerpt specifies LM211 operation from −25°C to +85°C and LM311 operation from 0°C to +70°C for the referenced comparison. The same excerpt states that offset voltage, offset current, and bias-current specifications apply from a single 5 V supply up to ±15 V supplies, and that the positive input voltage limit is 30 V above the negative supply. Exact ordering codes and package-specific electrical limits require the relevant manufacturer datasheet and suffix. Typical uses include sensing a control voltage against a reference, detecting an overvoltage condition, switching a relay when a sensor crosses a threshold, and interfacing an analog signal to TTL or MOS logic. Because the output is open collector, a pull-up resistor is generally required. The pull-up must be selected against the required sink current, output voltage, speed, and system supply constraints. The principal design consideration is ensuring that input common-mode voltage, supply voltage, output pull-up, and input/output isolation meet the particular LM211 or LM311 ordering variant. The family designation alone does not identify a unique package, suffix, temperature grade, or exact parameter set. Use the manufacturer datasheet linked on this page before committing a footprint or substituting a part. This page consolidates the verified manufacturer descriptions, practical comparator usage guidance, and the available cross-reference information. It distinguishes confirmed family-level facts from ordering-code-specific data that is not established by the supplied search results.

Cotação Contato

LM211D

LM211D - Single Differential Comparator with Strobe | Texas Instruments

The Texas Instruments LM211D is a single differential comparator with strobes that operates from wide-ranging power supplies, including ±15 V operational-amplifier rails and 5 V logic systems. Its open-collector output is compatible with most TTL and MOS circuits, and the device can drive lamps or relays. The LM211D is supplied in an 8-pin SOIC package, with an operating temperature range of -40°C to +85°C. A differential comparator is an integrated circuit that compares two input voltages and changes its output state according to their relative polarity. It belongs to the comparator hierarchy within analog and interface semiconductors: differential comparator → voltage comparator → analog interface IC → semiconductor. Unlike a general-purpose operational amplifier, the LM211D provides a saturated, logic-oriented output intended for threshold detection and switching rather than linear amplification. The LM211 family is described by Texas Instruments as a single high-speed voltage comparator. Its differential inputs allow a circuit to establish a switching threshold with an external reference, while the strobe function provides control over when the internal output participates in state changes. The open-collector architecture supports wired-interface and pull-up arrangements, although the required pull-up component and its implementation details are not included in the supplied source snippets. The LM211D uses logic-compatible output levels that can interface with TTL and MOS logic. This makes it suitable for translating an analog decision into a digital control signal. The manufacturer specifically identifies lamp and relay driving as supported applications, although the exact current limits, output sink-current ratings, response times, input common-mode limits, and input offset voltage were not present in the retrieved data and must be confirmed in the complete manufacturer datasheet before a final design is released. Typical uses include sensing a voltage crossing a reference level, detecting the state of a sensor or timing signal, driving digital control logic, and operating lamp or relay interfaces. In a practical circuit, the two inputs receive the signal and threshold voltages, the output uses an appropriate pull-up arrangement for open-collector operation, and the strobe pin is connected so the application can either enable or disable normal comparison behavior as required. The primary design consideration is to verify the complete electrical limits and pin functions from the official LM211 datasheet before layout sign-off. Designers should pay particular attention to input common-mode range, output current, supply sequencing, open-collector pull-up voltage, and strobe logic because these values were not included in the retrieved snippets. The 8-pin SOIC footprint also requires adequate spacing between adjacent pins for soldering and inspection. This page consolidates verified manufacturer and distributor information, cross-brand sourcing references, package details, selection guidance, and application-specific engineering considerations. It also clearly separates confirmed LM211D characteristics from parameters that still require datasheet verification, providing a useful basis for early component selection without replacing the authoritative manufacturer documentation.

Cotação Contato

LM211DG

LM211DG - 200 ns Single Comparator | onsemi | SOIC-8

onsemi LM211DG is a single high-speed voltage comparator with a 200 ns response time, 5 V to 30 V single-supply operation, and an open-collector output in an 8-pin SOIC package. It can also operate from split supplies, including ±15 V rails commonly used with operational amplifiers. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM211 belongs to the broader comparator, analog IC, and semiconductor hierarchy. Its open-collector output can interface with TTL, MOS, DTL, and RTL logic, while its ability to accept split supplies makes it useful in systems that do not share a common signal ground. Key features include one comparator channel, a 200 ns response time, and operation across a 5 V to 30 V single-supply range. The open-collector output provides a flexible way to drive compatible digital logic, lamps, or relays when an appropriate pull-up arrangement is used. The specified operating temperature range for LM211DG is -25°C to 85°C. The LM211 architecture is designed for high-speed threshold detection rather than precision amplification. Its input stage can operate independently of system ground, which helps when comparing signals referenced to a different potential. The open-collector output remains in a high-impedance state unless pulled down, allowing the output transition speed to depend partly on the external pull-up resistor and associated capacitance. Typical applications include industrial control interfaces, pulse-width and timing circuits, sensor threshold detection, relay or lamp drive, level translation between analog and digital systems, and general-purpose logic interfacing. The combination of a 200 ns response time and flexible supply options also suits pulse-width measurement and fast event detection circuits. When designing around the LM211DG, account for the open-collector output when calculating rise time and fanout. Keep input and output paths short, use a pull-up resistor appropriate for the driven logic family, and check input common-mode limits for the selected supply configuration before finalizing the schematic. This product summary combines the LM211DG electrical envelope, package information, sourcing context, pin-compatible alternatives, and practical interface guidance. It supports faster component selection by separating core operating characteristics from application-specific design considerations.

Cotação Contato

LM211DR

LM211DR - 115ns Differential Comparator | Texas Instruments

Texas Instruments LM211DR is a single high-speed differential comparator with a 115 ns response time, a 3.5 V to 30 V supply-voltage range, and an 8-pin SOIC package. Its open-collector or open-emitter output is compatible with common TTL and MOS logic levels, while its differential inputs support threshold and window comparisons. A voltage comparator is an analog signal-processing IC that compares two input voltages and changes its output state when the difference crosses a defined threshold. In the electronic-component hierarchy, an LM211 comparator belongs to the comparator category, then to analog interface ICs, and ultimately to integrated circuits. It provides a decision function between sensors, transducers, dividers, and digital control logic without converting the compared quantity into a coded data stream. The LM211 family operates from wide supply ranges, including positive 5 V logic systems and positive or negative 15 V analog supplies. Its high-speed response supports decisions that must occur quickly, while the open-collector output can interface with TTL and MOS circuits and drive loads such as lamps or relays. These characteristics make it useful when a logic system needs a fast threshold event rather than a continuous analog voltage. The differential input arrangement permits comparison of two changing voltages rather than one signal against ground alone. Input offset and common-mode limits remain important when selecting the input operating region, and the supply voltage must remain within the stated 3.5 V to 30 V range. Because the output stage is open-collector or open-emitter, an external pull-up resistor is generally required to establish a valid high output level in a wired logic interface. Typical LM211DR applications include sensor threshold detection, pulse-width and timing comparisons, industrial control interfaces, lamp or relay drive with suitable interface circuitry, and general-purpose logic conditioning. The 115 ns response time is especially useful where the comparator serves as a fast boundary detector between an analog node and a digital control system. In a practical circuit, place the comparator close to the signals being compared, route high-impedance input nodes carefully, and provide stable bypassing for the supply pins. Add the pull-up component required by the open-collector output stage and verify that relay, lamp, or other inductive loads are isolated or protected from transients. This product page combines manufacturer application guidance, package and timing details, orderable alternatives, and implementation-focused design notes. It also organizes the LM211DR for engineers who need to understand its logic compatibility, supply requirements, replacement choices, and PCB-level constraints before beginning a board design.

Cotação Contato

LM211DT

LM211DT - 200 ns Voltage Comparator | STMicroelectronics

STMicroelectronics LM211DT is a single general-purpose voltage comparator with a response time of 200 ns, low input current, and open-collector output. It is packaged in an 8-pin SOIC and operates from single 5 V supply to dual ±15 V supplies. The LM211 family is designed for precision threshold detection across industrial control, instrumentation, and logic-interface systems. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a selected threshold. In the broader semiconductor hierarchy, the LM211DT belongs to the comparator class, analog IC category, and power-management and signal-conditioning application ecosystem. Unlike an operational amplifier, the device is optimized for fast switching behavior and logic-compatible output drive rather than linear amplification. The principal features of the LM211DT include low input current, a 200 ns propagation delay, and an output compatible with TTL, DTL, RTL, MOS, and open-collector or open-emitter logic. Its open-collector output can sink logic-level current while the output transistor remains off, making pull-up placement and system-level bus design important. The wide supply-voltage range supports both traditional analog rails and modern single-supply logic systems. Internally, the comparator provides adjustable sensitivity because the output transition can be affected by the voltage difference between its non-inverting and inverting inputs. The STMicroelectronics datasheet also identifies a strobe control, allowing the designer to inhibit or enable output transitions according to system timing. Low input current is particularly useful when the comparator monitors high-impedance sensors, divider networks, or analog front ends where input bias current could shift the comparison threshold. Typical applications include industrial sensor threshold detection, overvoltage and undervoltage supervision, relay or solenoid drive, window-comparator circuits, level translation, and conditioning slow sensor signals into fast logic events. The open-collector output is useful in systems that require wired logic, pull-up-controlled buses, or a fail-safe output state when the device is unpowered. The primary design consideration is output topology. Place the required pull-up resistor from OUT to the positive logic rail, account for the maximum sink current, and use the STROBE pin according to the required timing. Check input common-mode range, supply polarity, output pull-up voltage, and propagation-delay requirements across the complete temperature range before treating a nominal 200 ns figure as sufficient for the application. This page combines the LM211DT electrical characteristics, package information, comparison options, and application guidance into an engineering-focused reference. It also highlights practical distinctions between the comparator's low-current inputs, wide supply range, strobe function, and open-collector output so that selection is based on circuit behavior rather than part number alone.

Cotação Contato

LM211N

LM211N - Wide-Supply Voltage Comparator | STMicroelectronics

The STMicroelectronics LM211N is a single, general-purpose voltage comparator supplied in an 8-pin DIP package. It is designed for operation from single +5 V logic supplies through ±15 V analog supplies, with compatible output levels for common TTL and MOS logic circuits. The verified distributor record identifies the LM211N as a standard comparator with DTL, MOS, open-collector, open-emitter, RTL, and TTL compatibility. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-oriented output indicating which input is higher. In the broader semiconductor hierarchy, the LM211N belongs to the comparator class within analog and mixed-signal ICs. Its open-collector output architecture is useful when the next stage needs a pull-up supply or when multiple devices must share a wired bus. The verified manufacturer-related results identify the LM111, LM211, and LM311 family as single high-speed voltage comparators designed for a wide range of supply voltages. The TI family description specifically highlights operation from ±15 V operational-amplifier supplies and 5 V logic supplies, while the ST result identifies low input currents and wide supply-voltage operation. The LM211N’s general-purpose comparator function supports threshold detection, sensing, switching, and control tasks. The STMicroelectronics result describes the device as usable with standard ±15 V operational-amplifier supplies and single +5 V logic supplies. Its output is compatible with many TTL and MOS circuits, and it is capable of driving lamps or relays according to the verified TI family description. The exact STMicroelectronics LM211N electrical limits, timing values, input-offset figures, output-current limits, and temperature-grade details were not included in the supplied source snippets and are marked for data completion. Typical applications include 5 V logic interfacing, relay or lamp drive, threshold crossing detection, industrial control, instrumentation, and systems where a comparator must operate across positive or split analog supplies. Because this product is an analog-to-logic decision element rather than a power device, SOA data is not applicable. The 8-DIP package is through-hole and is suited to legacy industrial, educational, prototype, and repair assemblies. The principal design consideration is confirming the complete pinout, supply limits, input common-mode range, output pull-up arrangement, and timing limits from the manufacturer datasheet before replacing another LM211-family device. The supplied web results confirm the functional family and package category, but do not provide enough numeric detail to claim a fully qualified cross-brand drop-in replacement. Compare the DIP footprint, pin numbering, open-collector output, input arrangement, supply range, and propagation delay before substitution. This page consolidates verified distributor and manufacturer-family information, identifies the LM211N’s comparator role and package category, and records missing technical values rather than guessing them. For a production replacement, use the official LM211N datasheet and validate every device-specific limit on the intended PCB.

Cotação Contato

LM211P

LM211P - High-Speed Voltage Comparator | Texas Instruments

The Texas Instruments LM211P is a single high-speed differential voltage comparator in an 8-PDIP package, operating from single 5 V supplies through split ±15 V supplies. It provides an open-collector output compatible with TTL and MOS logic and is capable of driving lamps and relays. The verified distributor data identifies a 115 ns response time, 3 mV input offset voltage, 100 nA input bias current, 6 µA typical input current, and a 106.02 dB gain-bandwidth figure. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM211P belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where it bridges precision analog sensing and digital logic control. Its differential inputs support sensing of a sensor signal relative to a reference, while its open-collector output provides a flexible interface to pull-up-based digital systems. The principal benefits are low input offset voltage, low input bias current, fast response, broad supply compatibility, and logic-level output compatibility. Its open-collector output can sink current from an external pull-up while remaining in an electrically inactive high-impedance state when turned off. This architecture is useful when the output must control a relay, lamp, indicator, or interface with a higher-voltage pull-up supply. The 8-PDIP through-hole package also simplifies prototyping, inspection, and repair in laboratory and industrial control systems. The LM211, LM111, and LM311 form a related high-speed comparator family. The LM211P is suitable for dual-supply operation around ±15 V and single-supply operation beginning at 5 V. Its inputs can be isolated from system ground, while the output can be referenced through its pull-up arrangement to ground, VCC, or another suitable rail. This flexibility is important when the sensed signal and logic interface use different voltage domains. Typical applications include overvoltage and undervoltage detection, sensor threshold conditioning, industrial control interfaces, relay activation, lamp indication, and conversion of analog events into logic-compatible signals. In such systems, the non-inverting input may receive a reference voltage and the inverting input may receive a feedback or sensor voltage, or the inputs may be reversed depending on the required switching polarity. The external pull-up resistor should be selected for the desired logic family and output current. A key design consideration is the strobe and output arrangement. The strobe pins are used for gating or inhibit control, while the open-collector output requires an external pull-up. Designers should verify input common-mode limits, supply polarity, pull-up voltage, output sink current, and logic thresholds for the specific system rather than relying only on nominal logic compatibility. This page consolidates verified manufacturer information, distributor pricing, pin-level guidance, application context, and strictly filtered drop-in alternatives. It distinguishes verified LM211 family options from mere functional equivalents and highlights the electrical checks required before replacing an original 8-pin comparator in an existing design.

Cotação Contato

LM211PW

LM211PW - Single Strobed Differential Comparator | Texas Instruments

The Texas Instruments LM211PW is a single strobed differential comparator with open-collector and open-emitter outputs, operating from wide supply voltages that include ±15 V and 5 V systems. It is packaged in an 8-pin TSSOP (PW) package. A differential comparator is an analog integrated circuit that compares two input voltages and produces a logic-oriented output indicating which input is higher. The LM211 belongs to the comparator and analog IC hierarchy, where it bridges an analog sensing function and downstream TTL, MOS, lamp, or relay control. Its strobe input allows the output state to be controlled for system timing, testing, or synchronization. The verified product information identifies the LM211PW as a single high-speed voltage comparator with strobe capability, open-collector and open-emitter outputs, and compatibility with most TTL and MOS circuits. Texas Instruments describes the LM111, LM211, and LM311 family as capable of driving lamps or relays and operating across a broad power-supply range. The PW package is identified as an 8-pin TSSOP. The open-collector and open-emitter outputs make output-state control and external pull-up or pull-down implementation important. The comparator is suitable for threshold detection, level translation, relay or lamp interfaces, industrial control logic, and mixed-signal systems where a decision is based on the relationship between two voltages. Its logic compatibility allows the output to interface with digital systems when appropriate external components are used. Typical applications include sensing a control voltage against a reference, detecting an overvoltage or undervoltage condition, generating a system enable signal, and switching a relay or lamp from a low-voltage control circuit. The LM211PW should be selected when a differential comparison function, wide supply-voltage support, strobe control, and an 8-pin TSSOP are required. Exact electrical ratings, pin behavior, output ratings, and recommended operating limits should be confirmed from the manufacturer datasheet before design release. The LM211PW datasheet is the authoritative source for pin assignments, voltage ranges, input common-mode behavior, output sink and source capabilities, timing characteristics, and application guidance. Verify the absolute maximum ratings, supply sequencing, input protection, output pull-up requirements, and external drive-current limits for the intended load. Do not assume that an open-collector output can source current without an appropriate pull-up or active external network. This product data combines the verified Texas Instruments product identity, distributor catalog information, package details, comparator function, and application-relevant guidance. It is intended to support component search, engineering selection, and design review while avoiding unverified electrical values that are not present in the supplied source material.

Cotação Contato

LM211QD

LM211QD - 115ns Differential Comparator | Texas Instruments

The Texas Instruments LM211QD is a single differential comparator with strobe capability, a 115 ns response time, and a supply-voltage range of 3.5 V to 30 V in an 8-pin SOIC package. It provides open-collector and open-emitter outputs suitable for TTL and MOS logic systems, lamp and relay drive, and analog signal-conditioning circuits. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a threshold. The LM211 belongs to the broader comparator hierarchy within analog and interface ICs, where it bridges the voltage-domain gap between analog sensors or signal chains and digital control logic. Its single-channel architecture provides a clear threshold decision while its wide supply range supports both 5 V logic and dual ±15 V analog systems. Key specifications include a maximum response time of 115 ns, maximum input bias current of 300 nA, and maximum input offset current of 70 nA. The device supports operation across -40°C to +125°C, making it suitable for industrial temperature ranges. Its open-collector and open-emitter output architecture supports wired logic and allows pull-up or pull-down networks to establish the desired output level. The LM211 architecture includes differential inputs and strobe control for coordinating comparator decisions in larger systems. The open-collector output can sink logic-level current, while the open-emitter structure provides complementary open-ended drive. Because open outputs do not establish a passive high level by themselves, external pull-up resistors are normally required when interfacing the collector output to TTL or MOS logic. Typical applications include pulse-width and timing circuits, zero-cross detection, sensor thresholding, overvoltage and undervoltage indication, industrial control interfaces, and relay or lamp activation. Its 115 ns response time supports decisions where propagation delay matters, while the 3.5 V to 30 V supply range permits use in both low-voltage logic systems and higher-voltage analog equipment. When designing a circuit around the LM211QD, begin with the output pull-up network and confirm that its resistor value satisfies the required sink current, rise time, and power dissipation. Keep comparator inputs away from switching nodes and high-current return paths, and use the strobe pin only according to the manufacturer timing and logic guidance. This page combines the LM211QD specifications, pin-compatible replacement information, application guidance, and selection criteria to support faster design decisions than a basic distributor listing. Use the Request a Quote form on this page for current commercial availability, price, and lead-time requirements.

Cotação Contato

LM218D

LM218D - 15MHz, 50V/us Operational Amplifier | TI

The Texas Instruments LM218D is a high-performance bipolar operational amplifier with 15 MHz typical small-signal bandwidth, 50 V/us minimum slew rate, and an 8-pin SOIC package. It is designed for precision, fast signal conditioning where wide bandwidth and high slew rate are required without abandoning direct DC performance. An operational amplifier is a high-gain, differential-input active device used in amplifier, comparator, filtering, summing, and feedback-control circuits. The LM218 belongs to the bipolar operational-amplifier hierarchy and combines a wide common-mode capability with internal frequency compensation. Its speed supports accurate reproduction of rapidly changing signals rather than only low-frequency voltage regulation or buffering. The verified LM218 data identifies bipolar technology, nominal voltage gain of 25,000, maximum supply voltage limit of 20 V, and a supply-voltage range extending to ±20 V. The LM218D is supplied in an 8-terminal gull-wing SOP package, with an 8-SOIC outline reported by Rochester Electronics. These characteristics suit instrumentation, waveform processing, and feedback systems requiring substantially more bandwidth than general-purpose single-supply amplifiers. Because the device is bipolar, input bias current and noise characteristics must be considered when the source impedance is high. The input network should also be checked against the common-mode input range at the actual supply voltages. Internal frequency compensation removes the need for an external compensation network in ordinary closed-loop use, although loop gain and stability still depend on the surrounding feedback network and load. Typical uses include low- and intermediate-frequency instrumentation, pulse and waveform conditioning, active filtering, servo control, and analog signal processing. The 15 MHz bandwidth and 50 V/us minimum slew rate are the principal selection criteria when signal edges must remain accurate. Applications requiring rail-to-rail input or output operation, single-supply operation near zero volts, or very low offset and bias current should use a different amplifier family. For a new PCB, preserve the verified eight-pin SOIC footprint and verify the complete manufacturer pinout before layout. Existing designs should check supply polarity, input common-mode range, output swing, decoupling, and stability across the intended load. This page combines the supplied distributor data, available cross-reference information, and engineering guidance without treating unverified performance values as facts.

Cotação Contato

LM219D

LM219D - High-Speed Dual Comparator, 5V-36V | STMicroelectronics

The STMicroelectronics LM219D is a precision high-speed dual voltage comparator in a 14-pin SOIC package, designed to operate over a wide range of supply voltages down to a single 5V logic supply and ground. The device delivers two independent comparators with low input bias current, high gain, and TTL-compatible open-collector / open-emitter outputs suitable for both single- and dual-supply operation from +5V to +/-15V. A voltage comparator is an analog building block that compares two input voltages and produces a digital output indicating which input is larger. The LM219 belongs to the comparator family within the broader amplifier and signal-conditioning category, sitting hierarchically between operational amplifiers (which drive linear output stages) and pure logic gates (which accept only digital inputs). The dual-channel configuration means two independent comparators share one package, optimizing board area and cost for parallel signal-monitoring tasks. Key specifications of the LM219D include response time in the hundreds of nanoseconds, input offset voltage in the millivolt range, and a wide common-mode input voltage range that extends to the negative supply rail. The open-collector / open-emitter output stage allows flexible interface to TTL, CMOS, and higher-voltage loads via an external pull-up resistor, enabling level shifting between the comparator supply domain and downstream logic. The architecture uses a precision input stage followed by a high-gain differential amplifier and an output stage designed for fast saturation recovery. According to the manufacturer datasheet, the device maintains its specified offset voltage, offset current, and bias current behavior over the entire supply range from a single +5V up to +/-15V, simplifying designs that must operate from multiple rails. The TTL-compatible strobe and latch inputs on the LM219 (versus the LM339/LM2901 family) add functionality for high-speed sampling applications. Typical applications include window comparators, zero-crossing detectors, line receivers, pulse-width modulators, A/D converters, and high-speed analog-to-digital front ends. The wide supply range makes the LM219D well-suited to industrial control, automotive, and instrumentation systems where both 5V logic and 15V analog rails coexist. When designing with the LM219D, ensure the output pull-up resistor is sized correctly for the target load and switching speed, and add hysteresis via positive feedback if input noise near the threshold could cause chatter. The SO-14 package offers standard 14-pin SOIC footprints that are pin-compatible with the LM319 family in the same package. This page synthesizes distributor pricing, drop-in alternatives in the same SOIC-14 footprint, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato

LM219DT

LM219DT - High-Speed Dual Comparator | STMicroelectronics

STMicroelectronics LM219DT is a high-speed dual voltage comparator designed for precision signal comparison over wide supply-voltage ranges. The device contains two independent comparators in a 14-pin SO surface-mount package, supports operation from a single 5 V logic supply to approximately ±15 V, and provides open-collector, open-emitter, TTL-compatible outputs. Its nominal propagation delay is approximately 80 ns, making it suitable for systems requiring faster decision-making than general-purpose comparator families. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM219DT belongs to the broader comparator and linear-comparator hierarchy within integrated circuits. Its dual architecture allows one package to perform two independent comparisons, while the wide operating-voltage range supports both low-voltage logic systems and bipolar industrial circuits. The principal features of the LM219DT include low input current, high gain, TTL-compatible outputs, and operation down to a single 5 V supply. These characteristics are useful when a sensing node has high source impedance, because the comparator must avoid loading the measured signal. The open-collector and open-emitter output structure also provides flexibility for level translation and wired-interface applications, although pull-up circuitry and output-state timing require careful review. The device is intended for applications in industrial control, power management, signal conditioning, threshold detection, and digital-interface conversion. Its approximately 80 ns response can support pulse-width measurement, timing supervision, fast overvoltage detection, and switching-control loops. Unlike an analog amplifier, the LM219DT is intended primarily to make a fast binary decision rather than provide a continuously scaled analog output. Designers should account for input common-mode range, output pull-up requirements, propagation-delay variation, and output sink-current capability before assigning the device. Because the outputs are open collector and open emitter, external pull-up or pull-down networks are normally required for conventional positive or negative logic levels. The manufacturer datasheet pin description and electrical characteristic tables should be used to verify each signal path and operating condition. This product overview combines the manufacturer datasheet information with practical engineering guidance for comparing LM219DT implementations, planning logic-interface circuitry, and selecting a replacement when package, pinout, supply range, output architecture, and timing requirements all matter.

Cotação Contato

LM219J

LM219J - High-Speed Dual Comparator | Texas Instruments

The Texas Instruments LM219J is a general-purpose, high-speed dual comparator with two independent comparison channels, a 5 V to 30 V supply range, and a 14-CDIP package. It is designed for applications requiring rapid logic-level decisions and compatibility with DTL, open-collector, open-emitter, RTL, and TTL interfaces. The device is supplied in a 0.300-inch, 7.62 mm ceramic dual-inline package. A comparator is an analog-to-digital decision component that compares two input voltages and produces a logic-oriented output indicating which input is higher. In the broader electronics hierarchy, the LM219J belongs to the comparator and linear IC families, alongside logic-compatible interface and signal-conditioning devices. Its two channels can be used independently for threshold detection, zero-crossing detection, pulse shaping, or basic control loops. The verified LM219J information identifies a dual general-purpose comparator, a 5 V to 30 V supply range, and DTL, open-collector, open-emitter, RTL, and TTL output compatibility. These characteristics make it useful in legacy industrial logic, control, test, and instrumentation systems where existing designs depend on high-voltage-compatible inputs and established logic interfaces. The dual-channel configuration also reduces the component count when two comparison functions are required. The LM219J family is described as a precision high-speed dual comparator fabricated on a single monolithic chip. The verified data does not provide a full electrical parameter table, propagation-delay value, input-offset specification, input-current limit, or output-current rating, so those values are not inferred here. Applications should be checked against the manufacturer datasheet before relying on timing, noise, input common-mode range, or output-drive limits. Typical uses include industrial control logic, digital threshold detection, pulse and signal monitoring, legacy computer interfaces, process-control instrumentation, and embedded systems using open-collector or TTL-compatible signaling. The 14-CDIP package favors through-hole legacy boards and repair or modernization projects rather than compact surface-mount assemblies. When upgrading a PCB, confirm pin numbering, supply polarity, input polarity, output pull-up requirements, and timing margins before substitution. For robust implementation, place the device close to the circuitry whose signals are being compared, maintain the required supply voltage, and observe the output-load requirements of the selected interface. Open-collector outputs generally need an external pull-up network, while TTL-compatible systems may use active drive. PCB layout should minimize long comparator input traces and provide adequate bypassing around the supply pins. This page combines verified distributor and cross-reference information with practical engineering guidance. It explicitly separates available facts from missing parameters so that procurement, replacement, and high-speed circuit decisions can be checked against the authoritative Texas Instruments documentation before design release.

USD $18,87 Em estoque

LM219N

LM219N - High-Speed Dual Comparator | STMicroelectronics

The STMicroelectronics LM219N is a high-speed dual voltage comparator supplied in a 14-pin PDIP package. The device operates from a single +5 V supply through ±15 V dual supplies, uses open-collector or open-emitter outputs, and provides separate comparator channels for precision threshold detection and fast switching. The verified product listing identifies it as a standard general-purpose comparator compatible with TTL logic. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. In the broader semiconductor hierarchy, a comparator belongs to the linear and mixed-signal IC family and supports systems built around logic ICs, power management, signal conditioning, and control electronics. The LM219N’s dual-channel architecture lets one package perform two threshold decisions or operate as a window comparator. Key verified features include low input currents, high gain, wide supply-voltage operation, and high-speed switching. The manufacturer's product page describes the LM219 family as precision high-speed dual comparators designed to operate from a single 5 V logic supply and ground. The distributor listing identifies the LM219N as having open-collector/open-emitter outputs and a 14-DIP package. Its comparator outputs can interface with TTL-compatible downstream logic when operated within the datasheet limits. The LM219N is suited to pulse-width shaping, level detection, zero-crossing detection, industrial control, test equipment, and signal conditioning. The two independent channels provide flexibility for comparing a sensor signal against a reference or detecting upper and lower thresholds. Because it is a through-hole PDIP device, it is particularly useful for prototype boards, educational systems, legacy industrial equipment, and repair applications that require a standard 14-pin socket or plated-through-hole footprint. Designers should verify supply polarity, input common-mode limits, output pull-up requirements, input overvoltage protection, and timing behavior against the manufacturer datasheet before applying the comparator. Open-collector outputs require an appropriate pull-up arrangement when a valid high-level output is needed. Input filtering and layout should minimize noise pickup around high-impedance comparison nodes, while bypassing supply pins close to the device helps preserve switching performance. This page synthesizes verified manufacturer and distributor information, package details, application guidance, replacement qualification limits, and design notes. Because the supplied data does not provide complete numeric timing, temperature, output-current, or price tables, those fields are explicitly marked as data needed rather than estimated.

Cotação Contato

LM2202M

LM2202M - 230 MHz Video Amplifier | Texas Instruments

The Texas Instruments LM2202M is a 230 MHz video amplifier system designed for high-resolution monochrome and RGB color monitor applications, packaged in a 20-pin SOIC. It integrates one standard general-purpose video amplifier with a gated differential-input black-level clamp comparator, a DC-controlled attenuator for contrast control, and a DC-controlled sub-contrast function. A video amplifier system is a specialized analog signal-processing IC used to condition composite or component video signals for display equipment. Within the broader product hierarchy, it belongs to video amplifiers, then amplifier ICs, then analog and mixed-signal semiconductors. The LM2202M combines wideband video amplification with display-oriented control functions, reducing the number of separate external signal-conditioning blocks needed in a monitor design. The primary headline specifications are a 230 MHz bandwidth rating, one video channel, and a 20-SOIC package with a stated body width of 7.50 mm. The SOIC package is a surface-mount plastic package compatible with conventional PCB assembly. Its long gull-wing leads provide inspection and rework access, while the 20-pin format gives the device separate connections for video processing, control, bypass, and supply functions. The integrated black-level clamp comparator provides a way to establish and control the video black level in a display signal chain. Its differential input architecture is intended to reject unwanted common-mode variation at the clamp input. The DC-controlled attenuator supports contrast adjustment, while the sub-contrast control permits a lower-level adjustment of the attenuation range. Together, these functions support display designs in which picture brightness and contrast require external operator adjustment. Typical applications include high-resolution monochrome CRT monitor front ends, RGB color monitor video channels, video projection equipment, and other display systems operating with wideband video signals. In these systems, the amplifier can process the incoming video waveform while the clamp and attenuation functions establish usable brightness and contrast behavior. Designers should preserve the recommended signal path topology because feedback, bypassing, and control-voltage routing materially affect bandwidth and stability. Use the pin-description and application-circuit sections in the National Semiconductor manufacturer datasheet when assigning traces and selecting bypass capacitors. The 230 MHz rating identifies the device as a high-frequency video part rather than a general-purpose op amp. Board layout should therefore minimize trace length around the video input and output, maintain a continuous ground return, and keep the clamp and contrast-control networks away from high-current switching paths. This page organizes the verified LM2202M package information, functional description, current sourcing path, and design guidance into a compact engineering reference. It also distinguishes exact drop-in replacements from suffix or packaging variants so that PCB reuse decisions are based on package, pinout, and function rather than part-number similarity alone.

Cotação Contato

Subcategorias

Produtos (39.000+)

LIFCL-40-9MG289C - CrossLink-NX 39K LUT FPGA, 289-TFBGA | Lattice

LM-555N - Single 555 Timer, 8-PDIP | Texas Instruments

LM111 - High-Speed Differential Comparator | Texas Instruments

LM111-LM211 - High-Speed Differential Comparator | Texas Instruments

LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments

LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments

LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics

LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments

LM201AN - Single Non-Compensated Op Amp | STMicroelectronics

LM211-LM311 - Single High-Speed Differential Comparator

LM211D - Single Differential Comparator with Strobe | Texas Instruments

LM211DG - 200 ns Single Comparator | onsemi | SOIC-8

LM211DR - 115ns Differential Comparator | Texas Instruments

LM211DT - 200 ns Voltage Comparator | STMicroelectronics

LM211N - Wide-Supply Voltage Comparator | STMicroelectronics

LM211P - High-Speed Voltage Comparator | Texas Instruments

LM211PW - Single Strobed Differential Comparator | Texas Instruments

LM211QD - 115ns Differential Comparator | Texas Instruments

LM218D - 15MHz, 50V/us Operational Amplifier | TI

LM219D - High-Speed Dual Comparator, 5V-36V | STMicroelectronics

LM219DT - High-Speed Dual Comparator | STMicroelectronics

LM219J - High-Speed Dual Comparator | Texas Instruments

LM219N - High-Speed Dual Comparator | STMicroelectronics

LM2202M - 230 MHz Video Amplifier | Texas Instruments