Microcontroladores

Produtos (20.000+)

MC9S12DJ256CPV - 16-bit 256KB Flash HCS12 MCU | NXP 112-LQFP
MC9S12DJ256CPV

MC9S12DJ256CPV - 16-bit 256KB Flash HCS12 MCU | NXP 112-LQFP

The NXP (formerly Freescale) MC9S12DJ256CPV is a 16-bit HCS12 CISC microcontroller with 256 KB of on-chip Flash, 25 MHz CPU12 core, 5V supply, and automotive AEC-Q100 qualification in a 112-pin LQFP (20x20 mm) package. Designed for automotive multiplexing, body controllers, and industrial networked nodes, the 'J' device variant integrates dual CAN 2.0 controllers, dual SCI (serial communications interface) and dual SPI ports, supporting SAE J1939 and CANopen stacks natively. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and on-chip peripherals into one package. The HCS12 family extends the legacy HC11 architecture with a 16-bit data path, an enhanced instruction set, and XGATE coprocessor options on higher-tier parts. Within the broader hierarchy, the MC9S12DJ256CPV is classified as: microcontroller -> 16-bit MCU -> HCS12 family -> automotive body/ chassis controller class -> semiconductor IC. Key features include 256 KB Flash, 12 KB RAM, 4 KB EEPROM, two CAN 2.0A/B modules, two SCI, two SPI, an 8-channel 10-bit ADC, an 8-channel enhanced capture timer, PWM channels, an IIC bus interface, up to 20 discrete digital I/O lines, and a background debug mode (BDM) for in-circuit programming. The integrated CAN controllers plus 5V-tolerant I/O make this MCU particularly well suited to 12V automotive battery transients without external transceivers. The HCS12 CPU12 core delivers 25 MHz bus speed and uses a von Neumann architecture with a 16-bit ALU. The peripheral set is mapped through a unified memory map that allows the integrated interrupt controller and module mapping to provide deterministic real-time response for body and chassis control loops. The device supports up to 25 MHz system clock and offers low-power stop and wait modes for quiescent current-sensitive designs. Typical applications include automotive body control modules (BCM), instrument clusters, HVAC controllers, central door locking, seat controllers, body-electronics gateway nodes, and industrial CAN nodes requiring 5V tolerant I/O. The dual-CAN plus dual-SCI configuration enables simultaneous vehicle bus and diagnostic-link connectivity. When designing with this device, place two 0.1 uF and 4.7 uF decoupling capacitors as close as possible to the VDD/VSS pairs and route the oscillator traces with a ground guard ring. The 5V supply tolerance simplifies integration into existing 12V automotive boards where load-dump transients (ISO 7637-2) are present. This page synthesizes distributor pricing from NXP's authorized channel, drop-in same-package alternatives in the MC9S12D family, and practical design notes on 5V automotive CAN node design not found in the manufacturer datasheet alone.

Cotação Contato
MC9S12DJ256MFUE - 16-Bit 25MHz 256KB MCU | NXP
MC9S12DJ256MFUE

MC9S12DJ256MFUE - 16-Bit 25MHz 256KB MCU | NXP

The NXP Semiconductors MC9S12DJ256MFUE is a 16-bit HCS12 CISC microcontroller with a 25 MHz maximum clock, 256 KB of Flash memory, and an 80-pin PQFP package. It is designed for automotive multiplexing applications and integrates two asynchronous serial communication interfaces, two 8-channel 10-bit ADCs, an 8-channel PWM module, an enhanced capture timer, and 59 I/O lines. The device is identified as NRND by the NXP product page. A microcontroller is a programmable control component that executes firmware, reads inputs, manages interfaces, and controls external hardware. The HCS12 family combines a 16-bit CISC core with automotive-oriented peripherals and system integration functions. In the broader hierarchy, this device is a microcontroller, embedded processor, semiconductor, and automotive electronic component. The verified information identifies two asynchronous serial communications interfaces, two 8-channel 10-bit ADCs, an 8-channel PWM, a 20-channel enhanced capture timer, 20 discrete digital I/O lines, and 59 total I/O ports. Its 256 KB Flash memory provides on-chip program storage, while the HCS12 platform supports system resource mapping, clock generation, interrupt control, and bus interfacing. The NXP overview specifically places the MC9S12D family in automotive multiplexing applications. The MC9S12D architecture uses full 16-bit internal data paths while allowing the external bus to operate in an 8-bit narrow mode for lower-cost memory interfacing. The SIM manages system resource mapping, clock generation, interrupts, and bus interfaces. The supplied distributor records identify the device as a 16-bit HCS12 microcontroller with Flash memory and an 80-pin package; one verified record states 25 MHz maximum frequency, while another third-party summary states 50 MHz, so the manufacturer record is used for the canonical specification and the discrepancy is flagged for validation. Typical applications include automotive body or multiplexing controllers, distributed control modules, actuator interfaces, sensor acquisition systems, and other embedded control platforms requiring multiple analog channels, serial communication, PWM outputs, and deterministic bus interfacing. The automotive orientation makes the device suitable for designs where peripheral integration and 16-bit control throughput are important. When designing around this MCU, verify the exact power, temperature, memory-map, oscillator, and peripheral limits in the NXP datasheet before release. Use the package pinout and manufacturer reference documentation for decoupling, clock, reset, analog-input, and external-bus layout. Because the part is NRND, new production designs should confirm lifecycle availability and migration requirements with NXP. This page consolidates verified manufacturer, distributor, and technical-source information, highlights the device's verified peripheral set and package, and identifies where additional datasheet data or lifecycle confirmation is required. It is intended to support engineering comparison, sourcing, and design review rather than replace the manufacturer documentation.

Cotação Contato
MC9S12DJ256MPVE - HCS12 16-Bit MCU 256KB Flash | NXP | Automotive
MC9S12DJ256MPVE

MC9S12DJ256MPVE - HCS12 16-Bit MCU 256KB Flash | NXP | Automotive

The NXP Semiconductors MC9S12DJ256MPVE is an HCS12 family 16-bit Flash microcontroller (MCU) delivering 25 MHz CPU performance with 256 KB on-chip Flash, 12 KB RAM, and 4 KB EEPROM in a 112-pin LQFP package (20x20 mm). The device is AEC-Q100 qualified for automotive multiplexing applications, with an operating temperature range of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and I/O peripherals. The HCS12 is a 16-bit CISC architecture with a rich peripheral set including enhanced capture timers, 10-bit ADCs, PWM channels, and serial communication interfaces, widely deployed in automotive body, chassis, and powertrain ECUs where deterministic real-time response is required. Key features of the MC9S12DJ256MPVE include two asynchronous SCI channels, two 8-channel 10-bit ADC modules, an 8-channel enhanced capture timer supporting input capture/output compare/PWM functions, 8-channel PWM, 20+ discrete digital I/O lines, and a CAN 2.0 module. The integrated Background Debug Mode (BDM) and on-chip voltage regulator simplify in-circuit programming and field updates. Built on NXP's mature HCS12 CISC core, the MC9S12DJ256MPVE implements Harvard-style bus architecture with separate program and data paths, providing deterministic interrupt latency critical for automotive multiplexing. The on-chip voltage regulator allows single 5V supply operation while internally generating the 2.5V core voltage needed by the Flash and logic blocks. Typical applications include automotive body control modules (BCMs), instrument clusters, HVAC controllers, door/window/seat modules, lighting controllers, and industrial CAN-based distributed control nodes. The wide AEC-Q100 temperature range and robust peripheral mix make it a workhorse for cost-sensitive in-vehicle networking. When designing with this MCU, allocate proper decoupling (100 nF + 10 uF near VDD pins), respect the EXTAL/XTAL oscillator layout guidelines, and use the BDM interface for non-intrusive debug. Flash endurance is rated at 10K cycles minimum - design firmware update logic accordingly. This page synthesizes distributor stock data, drop-in LQFP-112 same-package alternatives from the S12D family, and practical design notes not found on the manufacturer datasheet.

Cotação Contato
MC9S12DJ64CPVE - 16-Bit HCS12 MCU 64KB Flash 25MHz | NXP
MC9S12DJ64CPVE

MC9S12DJ64CPVE - 16-Bit HCS12 MCU 64KB Flash 25MHz | NXP

The NXP Semiconductors MC9S12DJ64CPVE is a 16-bit HCS12 CISC microcontroller featuring 64KB of on-chip Flash program memory, 4KB of RAM, and 1KB of EEPROM, operating at up to 25MHz bus speed in a 112-pin LQFP (20x20mm) package. It integrates 91 general-purpose I/O lines and supports dual supply rails at 2.5V core / 5V I/O, making it well suited for mixed-voltage automotive and industrial subsystems. Background Knowledge - What is an HCS12 microcontroller? The HCS12 (also called S12) is a 16-bit CISC microcontroller family originally developed by Motorola and now maintained by NXP Semiconductors. It belongs to the broader category of embedded microcontrollers and is positioned between 8-bit MCUs (e.g., HC08, S08) and 32-bit devices (e.g., Kinetis, S32K). The HCS12 core uses a 16-bit data path with a 16-bit ALU, an extended memory map supporting banked addressing, and a peripheral co-processor (XGATE) on certain variants, enabling deterministic interrupt handling for automotive body and powertrain applications. Key features of the MC9S12DJ64CPVE include the HCS12 CPU core, 8-channel 10-bit A/D converter, PWM module, watchdog timer (WDT), and a rich connectivity set with two CAN (CANbus) controllers, one SCI, one SPI, and one I2C bus interface. Internal EEPROM allows non-volatile parameter storage without external serial EEPROM, while the integrated Flash supports in-application re-programming via standard BDM (Background Debug Mode) or serial bootstrap. Technical depth - The MC9S12DJ64CPVE is an automotive-grade part qualified to NXP's internal Q-100 process flow and supports an ambient operating temperature range consistent with industrial and automotive deployments. Two on-chip CAN 2.0A/B controllers make the device especially suitable for CAN-based body controllers, gateway modules, and OBD-II diagnostics, where deterministic bus arbitration and hardware message filtering reduce CPU overhead. Typical applications include automotive body control modules (BCM), instrument clusters, HVAC controls, industrial CAN nodes, and sensor aggregation nodes. The wide I/O count and dual CAN capability allow it to serve as a low-cost gateway between a CAN bus and lower-speed LIN or UART peripherals. Design consideration - The MC9S12DJ64CPVE requires an external crystal or oscillator for the PLL configuration; designers must follow the reference oscillator layout from the datasheet to avoid start-up failures due to stray capacitance. A single 5V supply powers the I/O pads while an internal 2.5V regulator powers the core, so decoupling must respect the routing recommendations in the datasheet to avoid core-voltage noise coupling into the analog reference. This page synthesizes distributor pricing, drop-in LQFP-112 alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
MC9S12DJ64MFUE - HCS12 16-bit MCU 64KB Flash 80-QFP | NXP
MC9S12DJ64MFUE

MC9S12DJ64MFUE - HCS12 16-bit MCU 64KB Flash 80-QFP | NXP

The NXP MC9S12DJ64MFUE is a 16-bit microcontroller built on the HCS12 core, delivering up to 25 MHz CPU performance with 64 KB of embedded Flash in an 80-pin QFP (14x14 mm) package. The device integrates two separate CAN 2.0 A/B modules (msCAN), an SCI, an SPI, plus multiple timers and an 8-channel 10-bit ADC, providing rich automotive and industrial connectivity in a single chip. Its 64 KB Flash memory (64K x 8) is complemented by 4 KB RAM and 1 KB EEPROM, with 8 KB Flash additionally usable as EEPROM-emulation back-store. The on-chip BDM (Background Debug Mode) and single-wire debug interface enable non-intrusive in-circuit programming and calibration, features that long-established automotive engineers value in the S12 architecture. A microcontroller (MCU) in this category is a self-contained computing subsystem integrating a CPU core, program and data memory, peripherals, and I/O on a single silicon die. HCS12 belongs to the 16-bit CISC microcontroller family; it descends from the HC11 line and sits between 8-bit MCUs (such as the Freescale HC08) and higher-end 32-bit microcontrollers (such as Cortex-M or Power Architecture). The MC9S12D series specifically targets distributed body and chassis automotive networks requiring both deterministic CAN communication and real-time control. Key features include 25 MHz bus speed at 5 V operation, two msCAN 2.0 A/B controllers, SCI, SPI, up to two 8-bit PWM channels plus a 16-bit pulse accumulator, an 8-channel 10-bit ADC with 7 µs conversion time, and an on-chip 1.0 V bandgap reference. The 80-QFP package offers generous I/O while remaining compatible with mid-density PCB assemblies. The HCS12 core is also fully upward-object-code compatible with the HC12 instruction set, allowing reuse of legacy firmware. The architecture combines a 16-bit register-rich CISC CPU with a 25 ns minimum instruction cycle at 25 MHz. The internal PLL can synthesise higher bus rates from the standard 4 MHz external crystal, supporting accelerated peripheral operation. Two msCAN modules enable isolated high-speed CAN channels for powertrain and body domains, while the ADC's 8 channels support simultaneous analog sensing with hardware trigger from timers. Typical applications include automotive body controllers (BCM), HVAC control panels, instrument clusters, industrial CAN nodes, OBD-II diagnostic interfaces, and seat/door/window modules. The dual-CAN architecture is also well-suited to vehicle gateway functions bridging powertrain and body networks. When designing with this MCU, pay attention to the 5 V I/O voltage tolerance, place the 4 MHz crystal within 5 mm of the EXTAL/XTAL pins with short symmetrical traces, and add bulk decoupling at AVDD/VDDR. NRND status should be planned against: confirm ongoing last-time-buy windows with NXP via authorized distributors and pre-qualify a successor. This page consolidates distributor pricing, life-cycle status, and drop-in alternatives not found in the manufacturer datasheet, giving engineers the actionable context needed for sourcing and migration decisions.

Cotação Contato
MC9S12DJ64MPVE - HCS12 16-Bit 64KB Flash MCU 112-LQFP | NXP
MC9S12DJ64MPVE

MC9S12DJ64MPVE - HCS12 16-Bit 64KB Flash MCU 112-LQFP | NXP

The NXP MC9S12DJ64MPVE is a 16-bit HCS12 family microcontroller featuring 64KB of Flash program memory, 4KB of RAM, and 1KB of EEPROM, operating at 25 MHz and housed in a 112-pin LQFP (20x20 mm) package. It is a member of the S12DJ sub-family and includes two CAN 2.0 A/B controllers, two SCI, two SPI, and one I2C peripheral interface, plus an 8-channel 16-bit timer/PWM block. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, data EEPROM, and a rich set of peripherals into one IC. The HCS12 core is a CISC 16-bit architecture from Motorola/Freescale/NXP targeting automotive and industrial embedded control. Within the broader taxonomy, MCUs sit below microprocessors in capability but above simple logic ICs in complexity; the HCS12 line specifically evolved from the HC11 and is one of the ancestors of today's S12 MagniV analog-integrated derivatives. Its place in the power-and-I/O-dense automotive ECU market explains why MC9S12 parts remain in long production cycles. Key features of the MC9S12DJ64MPVE include 91 general-purpose I/O lines, an internal oscillator, a watchdog timer, an 8-channel 10-bit ADC, and supply operation from 2.5V core / 5V I/O. The device supports Background Debug Mode (BDM) for in-circuit programming and debugging. Its single 5V supply with on-chip voltage regulator simplifies board design compared to parts requiring separate core and I/O rails. The architecture uses a 16-bit HCS12 CPU core with enhanced indexed addressing, a hardware multiply/divide, and a 16-bit accumulator/derivative stack optimized for C and assembly code generated by CodeWarrior. The two CAN 2.0 modules support up to 1 Mbps networking, making the part well-suited to multi-node automotive body and chassis networks. The 112-LQFP package exposes most signals to the outside, giving designers full access to the 91 I/O pins plus dedicated analog and timer channels. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, industrial CAN nodes, and motor control peripherals. The combination of CAN + SCI + SPI + I2C and 64KB of flash allows a single MC9S12DJ64 to host a complete LIN/CAN gateway or stepper-motor driver sub-system. When designing with this part, pay close attention to the decoupling network: place 100 nF ceramics close to every VDD/VSS pair, and a 4.7 uF bulk cap at the regulator output. Because the device is in long-term mature status with multiple sources, lead times are typically short. This page synthesizes distributor pricing, drop-in alternatives drawn from the same HCS12 sub-family, and practical design notes that go beyond the information found in the standalone manufacturer datasheet, giving an engineer one consolidated reference.

Cotação Contato
MC9S12DJ64VFUE - 16-bit HCS12 MCU, 64KB Flash, 80-LQFP | NXP
MC9S12DJ64VFUE

MC9S12DJ64VFUE - 16-bit HCS12 MCU, 64KB Flash, 80-LQFP | NXP

The NXP MC9S12DJ64VFUE is a 16-bit HCS12 microcontroller with 64 KB of on-chip Flash, 59 digital I/O lines, and an integrated 8-channel 10-bit ADC, packaged in an 80-pin LQFP (14x14 mm). It belongs to the S12D family and operates at a 25 MHz bus clock with a 2.35 V to 2.75 V supply, delivering CISC core performance for automotive and industrial embedded systems. A 16-bit microcontroller (MCU) is an integrated circuit that combines a CPU, memory, and programmable peripherals on a single silicon die. The HCS12 architecture is a CISC core derived from the Motorola/Freescale CPU12 lineage and is widely used in body electronics, powertrain, and chassis control modules where deterministic interrupt latency and on-chip CAN are required. Within the broader taxonomy, the MC9S12DJ64VFUE sits in the S12 microcontroller family -> 16-bit MCU -> automotive microcontroller -> semiconductor. Key features include 64 KB (64K x 8) of embedded Flash, two asynchronous SCI serial interfaces, two SPI interfaces, one I2C bus, an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel pulse-width modulator (PWM), and one CAN 2.0 A/B module. The device supports single-wire background debug mode (BDM) and includes a 20-bit interrupt vector table. Operating temperature is industrial-grade. The device uses a Harvard-style bus with separate program Flash and data paths, and integrates System Resource Mapping, Clock Generation, Interrupt Control, and Bus Interface units. The 10-bit ADC supports 8 channels with 7 us minimum conversion time, while the enhanced capture timer offers input-capture, output-compare, and pulse-width modulation on a single 16-bit free-running counter. The on-chip CAN module is fully CAN 2.0 A/B compliant with hardware acceptance filtering. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, seat and mirror controllers, industrial sensor nodes, and CAN-connected sensor hubs. Its combination of on-chip CAN, dual SCI, and PWM makes it well-suited for distributed mechatronic nodes that need to communicate over multiple buses simultaneously. When designing with this MCU, ensure the LQFP-80 land pattern follows JEDEC MS-026 tolerances and that the analog supply (VDDR/VSS) is decoupled with a 100 nF ceramic plus a 4.7 uF bulk capacitor placed within 5 mm of the pins. Leave the BDM pins accessible for in-circuit firmware updates during prototyping. This page synthesizes distributor pricing, drop-in alternatives within the S12D family, and practical design notes that complement the manufacturer datasheet and reference manual.

Cotação Contato
MC9S12DP512CPV - 16-Bit HCS12 MCU, 512KB Flash, 112-LQFP | NXP
MC9S12DP512CPV

MC9S12DP512CPV - 16-Bit HCS12 MCU, 512KB Flash, 112-LQFP | NXP

The NXP (formerly Freescale/Motorola) MC9S12DP512CPV is a 16-bit HCS12 microcontroller featuring 512 KB of on-chip Flash, 12 KB of RAM, and 91 general-purpose I/O lines in a 112-pin LQFP package running at 25 MHz bus frequency. It is the top-of-memory variant of the pin-compatible S12D-Family that scales from 32 KB to 512 KB of Flash, providing an upward migration path from Freescale's legacy 68HC08, 68HC11, and 68HC12 architectures. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of on-chip peripherals. Within the broader taxonomy, the MC9S12DP512CPV sits in the HCS12 family of automotive-grade 16-bit microcontrollers, descending from the original Motorola 68HC12 architecture. It is commonly classified as an automotive MCU / embedded processor, with applications spanning body electronics, industrial control, and CAN-node subsystems. Key features include two asynchronous Serial Communications Interfaces (SCI), one Serial Peripheral Interface (SPI), one Inter-IC (I2C) bus, an 8-channel 16-bit Enhanced Capture Timer (ECT), two 8-channel 10-bit Analog-to-Digital Converters (ADC), an 8-channel Pulse-Width Modulator (PWM), 20 discrete digital I/O lines with wake-up capability, and a Controller Area Network 2.0 (CAN 2.0) module. The S12 CPU core provides 16-bit native data paths with a 25 MHz bus for predictable real-time control performance. The device is fabricated on Freescale's industry-leading 0.25 micrometer Flash process, providing reliable embedded non-volatile storage and a robust instruction set optimized for C-language embedded development. Multiple on-chip peripherals share a sophisticated interrupt and bus-arbitration scheme via the System Resource Mapping block, allowing deterministic latency for time-critical tasks such as PWM generation, ADC sampling, and CAN message handling. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, CAN-based sensor nodes, industrial automation PLCs, and any legacy 68HC12 system that requires a transparent upward memory migration. The wide operating voltage range and automotive-grade temperature support make it a workhorse for chassis and body-electronics ECUs. When designing with this MCU, ensure your linker script accounts for the 512 KB Flash bank layout (sector erase = 1024 bytes, row = 64 words) and use the BDM (Background Debug Mode) interface for in-circuit programming and debug. For new platforms, prefer the pin-compatible MC9S12XDP512 (X-gate coprocessor, 2-5x performance) or the newer S12G family. This page synthesizes distributor pricing for the MC9S12DP512CPV, drop-in same-package alternatives across the HCS12 family, and practical design notes not collated in the manufacturer datasheet.

Cotação Contato
MC9S12DP512CPVE - 16-Bit 25MHz HCS12 MCU | NXP
MC9S12DP512CPVE

MC9S12DP512CPVE - 16-Bit 25MHz HCS12 MCU | NXP

The NXP Semiconductors MC9S12DP512CPVE is a 16-bit HCS12 CISC microcontroller operating at up to 25 MHz, with 512 KB of internal Flash, 12 KB of RAM, and 4 KB of EEPROM in a 112-pin LQFP package. Its integrated peripherals include two asynchronous serial communication interfaces, an 8-channel enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel PWM module, and 91 general-purpose I/O pins. A microcontroller is a programmable embedded-control IC that integrates a CPU core, memory, peripherals, and I/O on one device. The MC9S12DP512CPVE belongs to the MC9S12D family of Flash-based automotive-oriented 16-bit controllers. This family is designed for multiplexing and control applications requiring a deterministic instruction set, extensive I/O, communication resources, and analog measurement channels. NXP describes the MC9S12D as a pin-compatible family that scales from 32 KB to 512 KB of Flash memory. Key features include 512 KB internal Flash for firmware and data, a 25 MHz maximum operating frequency, and CISC-based HCS12 instruction processing. The device provides two 10-bit ADC channels groups, PWM outputs, enhanced timer capture, serial communications, interrupt control, clock generation, and bus interfacing. The 112-LQFP package exposes a large number of I/O and peripheral resources for automotive multiplexing and industrial embedded-control boards. The MC9S12DP512CPVE is suitable for 2.5 V and 5 V device operation according to the supplied distributor and comparison data. Its large memory and peripheral set can support protocol handling, actuator control, sensor acquisition, and system management. Firmware portability should still be checked when moving between related S12 devices because memory maps, peripherals, startup code, and errata can differ. The primary design consideration is package and software compatibility. The 112-LQFP footprint is not interchangeable with smaller MC9S12 packages, and related devices with different Flash sizes may not provide identical peripheral availability. Use the manufacturer datasheet and device errata when validating timing, pin multiplexing, and application behavior. This product page combines the verified manufacturer product information, distributor specifications, datasheet references, and practical sourcing context for engineers evaluating this 16-bit automotive-oriented MCU.

Cotação Contato
MC9S12DP512CPVER - 16-Bit 25MHz HCS12 MCU | NXP (Tape & Reel)
MC9S12DP512CPVER

MC9S12DP512CPVER - 16-Bit 25MHz HCS12 MCU | NXP (Tape & Reel)

The NXP Semiconductors MC9S12DP512CPVER is a 16-bit HCS12 CISC microcontroller operating at up to 25 MHz, with 512 KB of internal Flash, 12 KB of RAM, and 4 KB of EEPROM in a 112-pin LQFP package. Its integrated peripherals include two asynchronous serial communication interfaces, an 8-channel enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel PWM module, and 91 general-purpose I/O pins. A microcontroller is a programmable embedded-control IC that integrates a CPU core, memory, peripherals, and I/O on one device. The MC9S12DP512CPVER belongs to the MC9S12D family of Flash-based automotive-oriented 16-bit controllers. This family is designed for multiplexing and control applications requiring a deterministic instruction set, extensive I/O, communication resources, and analog measurement channels. NXP describes the MC9S12D as a pin-compatible family that scales from 32 KB to 512 KB of Flash memory. Key features include 512 KB internal Flash for firmware and data, a 25 MHz maximum operating frequency, and CISC-based HCS12 instruction processing. The device provides two 10-bit ADC channels groups, PWM outputs, enhanced timer capture, serial communications, interrupt control, clock generation, and bus interfacing. The 112-LQFP package exposes a large number of I/O and peripheral resources for automotive multiplexing and industrial embedded-control boards. The MC9S12DP512CPVER is suitable for 2.5 V and 5 V device operation according to the supplied distributor and comparison data. Its large memory and peripheral set can support protocol handling, actuator control, sensor acquisition, and system management. Firmware portability should still be checked when moving between related S12 devices because memory maps, peripherals, startup code, and errata can differ. The primary design consideration is package and software compatibility. The 112-LQFP footprint is not interchangeable with smaller MC9S12 packages, and related devices with different Flash sizes may not provide identical peripheral availability. Use the manufacturer datasheet and device errata when validating timing, pin multiplexing, and application behavior. This product page combines the verified manufacturer product information, distributor specifications, datasheet references, and practical sourcing context for engineers evaluating this 16-bit automotive-oriented MCU.

Cotação Contato
MC9S12DP512MPVE - 16-bit 25MHz 512KB Flash MCU | NXP
MC9S12DP512MPVE

MC9S12DP512MPVE - 16-bit 25MHz 512KB Flash MCU | NXP

The NXP Semiconductors MC9S12DP512MPVE is a 16-bit HCS12 microcontroller operating at 25 MHz with 512 KB of Flash memory, 12 KB of RAM, and 4 KB of EEPROM, housed in a 112-pin LQFP (20x20 mm) package. A 16-bit microcontroller is a complete computer-on-a-chip whose CPU processes data in 16-bit words, sitting above 8-bit MCUs in arithmetic throughput while remaining far simpler than 32-bit parts. The HCS12 (S12) family evolved from the Freescale 68HC12 lineage and remains a mainstay of automotive body electronics and industrial control, offering CISC efficiency, extensive peripheral integration, and an upward migration path from the 68HC08, 68HC11, and 68HC12 architectures. Key features include the enhanced HCS12 CISC CPU at up to 25 MHz bus speed, 512 KB of 0.25 um on-chip Flash with 1024-byte sector erase, 91 general-purpose I/O lines, and two asynchronous serial communications interfaces (SCI). The peripheral set is rich for its class: an 8-channel enhanced capture timer (IC/OC), an 8-channel pulse-width modulator, an Inter-IC (IIC) bus, and a system of standardized on-chip modules with unified resource mapping, clock generation, and interrupt control. Technically, the MC9S12D series combines standard on-chip peripherals around a 16-bit CPU12 core. Analog capability comprises two 8-channel 10-bit ADCs, providing up to 16 analog inputs for sensor acquisition. Flash-based program memory supports in-system reprogramming, and the pin-compatible S12 family scales from 32 KB to 512 KB of Flash, enabling scalable designs on a single PCB footprint. Typical applications are automotive multiplexing systems, body control modules, instrument clusters, gateway nodes, and industrial control equipment where 16-bit processing, generous Flash, and mature tooling matter more than raw 32-bit performance. Design consideration: budget oscillator selection and bus-clock divider settings carefully to hit the 25 MHz bus maximum while meeting the flash programming and ADC clock constraints; also account for the full 512 KB paged memory model in the linker configuration. This page synthesizes distributor pricing context, drop-in alternatives within the S12 family, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
MC9S12DT128BCPV - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP
MC9S12DT128BCPV

MC9S12DT128BCPV - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP

The NXP MC9S12DT128BCPV is a 16-bit HCS12 microcontroller from the S12DT128 family, featuring 128KB of on-chip Flash program memory, 8KB of RAM, and 91 general-purpose I/O pins in a 112-pin LQFP package. The device operates at up to 25MHz bus clock and is fabricated in a 0.25um process that supports both 3.3V and 5V mixed-voltage I/O for direct interface to legacy 5V peripherals. The part suffix "B" denotes the standard Flash die revision, "C" indicates the 112-LQFP package option, and "PV" designates the -40C to +85C industrial temperature grade. A 16-bit microcontroller (MCU) is an embedded computing device whose central processing unit manipulates data in 16-bit-wide chunks, providing a balance between the simplicity of 8-bit parts and the computational throughput of 32-bit cores. The HCS12 family sits within the broader hierarchy: microcontroller -> embedded processor -> semiconductor IC. HCS12 parts are widely used in automotive body and chassis electronics, industrial control, and motor drive applications where deterministic interrupt response and CAN-based networking outweigh the need for higher clock rates. Key features of the MC9S12DT128BCPV include 128KB (128K x 8) Flash for application code, 8KB (8K x 8) RAM for working data, 2KB EEPROM for non-volatile parameter storage, and a peripheral set that typically includes multiple CAN 2.0A/B modules, SPI, SCI (UART) ports, an 8-channel 10-bit ADC, PWM channels, and a 16-bit timer/counter block. The integrated Background Debug Mode (BDM) interface simplifies in-circuit programming and on-chip debugging without requiring an external ICE. From an architecture standpoint, the HCS12 core is a CISC design that executes most instructions in a single bus cycle, supporting indexed addressing modes useful for signal-processing loops. The integrated voltage regulator generates 2.5V for the core from a 5V or 3.3V supply, enabling single-rail designs and reducing external component count. Typical applications include automotive body controllers, instrument clusters, HVAC control modules, CAN-based sensor nodes, industrial PLC I/O modules, and consumer white-goods controllers. Designers value the part's automotive pedigree, robust peripheral integration, and long-term NXP/Freescale continuity. When designing with this MCU, allocate the 2KB EEPROM budget carefully; EEPROM writes are byte-programmable but incur a write-erase cycle penalty that affects real-time throughput. Place a 0.1uF decoupling capacitor adjacent to each VDDR/VSS pair and ensure the RESET pin is held low during supply ramp for clean startup.

Cotação Contato
MC9S12DT128BVPV - 16-Bit 50MHz 128KB Flash MCU | NXP
MC9S12DT128BVPV

MC9S12DT128BVPV - 16-Bit 50MHz 128KB Flash MCU | NXP

The NXP Semiconductors MC9S12DT128BVPV is a 16-bit CPU12 flash microcontroller rated at 50 MHz, with 128 KB of program memory and a 112-pin LQFP package measuring 20 mm by 20 mm. Verified distributor listings identify it as an industrial-grade, surface-mount microcontroller in a square gull-wing package. A microcontroller is a programmable system-on-chip that executes firmware, coordinates hardware peripherals, and manages control-system inputs and outputs. The HCS12/CPU12 family combines a 16-bit processor, flash program memory, data memory, timers, serial interfaces, interrupt control, and communication peripherals. Within the broader semiconductor hierarchy, this device belongs to the embedded-controller and automotive-electronics domains. Verified source data specifies 128 KB organized as 128K x 8, a 16-bit architecture, and a 50 MHz maximum listed frequency. Its 112-pin LQFP package provides a substantial pin count for external memory interfaces, communications, timers, analog control, and multiplexing applications. The family was designed for automotive multiplexing applications and pin-compatible family variants support scalable memory and peripheral selections. The source listings disagree on the operating frequency: Mouser describes a 25 MHz product, while DigiKey describes the exact MC9S12DT128BVPV as 50 MHz. Because the exact-MPN DigiKey listing and the detailed comparison result identify 50 MHz, that value is retained here, but engineers should confirm the relevant clock and bus limits against the manufacturer datasheet before release. Typical uses include automotive body and multiplexing controllers, embedded industrial controls, communication hubs, sensor-interface systems, and general 16-bit embedded platforms. The large package is useful where broad external connectivity is required, while the 128 KB flash capacity supports moderate standalone control firmware. Design decisions should focus on exact pin multiplexing, oscillator configuration, reset behavior, memory timing, and peripheral allocation. Before substituting another 112-pin device, verify every pin, peripheral mapping, clock rating, voltage requirement, and software-support element; package similarity alone does not establish drop-in compatibility. This page consolidates verified distributor specifications, source URLs, application context, comparison data, and replacement-screening guidance. Because public cross-reference results did not verify five true pin-to-pin alternatives, no unverified substitutes are presented as drop-in parts.

Cotação Contato
MC9S12DT128CPV - HCS12 16-Bit 25MHz MCU 128KB Flash | NXP | 112-LQFP
MC9S12DT128CPV

MC9S12DT128CPV - HCS12 16-Bit 25MHz MCU 128KB Flash | NXP | 112-LQFP

The NXP (formerly Freescale/Motorola) MC9S12DT128CPV is a 16-bit HCS12 CISC microcontroller built around the CPU12 core, offering 128KB of on-chip Flash program memory, 8KB of RAM and 2KB of EEPROM, clocked at up to 25 MHz, and housed in a 112-pin LQFP package (20x20 mm). It is designed for automotive multiplexing and body-electronics applications, integrating a rich peripheral set including up to 91 I/O lines, a PWM module, a watchdog timer, and multiple serial interfaces (CAN, SCI/SPI/I2C). The part is specified for industrial temperature operation, with a 2.5V/5V-tolerant supply for the HCS12 family. HCS12 microcontrollers are 16-bit CISC devices that originated as the evolution of the Motorola HC11 architecture, retaining code compatibility while adding background debug mode (BDM), a 16-bit CPU register set, and a sophisticated interrupt controller. As members of the broader microcontroller category, HCS12 devices sit below 32-bit ARM Cortex-M parts in flash-memory density but above 8-bit 8051/AVR devices in computational throughput, making them a fit for cost-sensitive real-time embedded control rather than high-throughput applications like graphics or wireless stacks. Key features of the MC9S12DT128CPV include 128KB Flash organized as 128K x 8, an integrated CAN 2.0 module for in-vehicle networking, pulse-width modulation outputs for motor or lighting drivers, and a watchdog timer for fail-safe recovery. The 8KB on-chip SRAM is sufficient for protocol stacks and small buffers, while the 2KB EEPROM supports non-volatile parameter storage (CAN IDs, calibration data, fault logs). The HCS12 core executes most instructions in a single bus cycle, giving effective throughput near 25 MIPS at the rated 25 MHz E-clock. Architecturally, the device combines the HCS12 CPU12 core, a multi-channel ADC (referenced in the family datasheet), an enhanced capture/timer module, and the BDLC/SCI/SPI/IIC blocks behind a standard HCS12 peripheral bridge. The part is fully pin-compatible with other members of the MC9S12D-Family, letting designers swap memory and peripheral options without board rework. According to the family datasheet, the design targets automotive multiplexing where CAN bandwidth and deterministic interrupt response are key. Typical applications for the MC9S12DT128CPV include automotive body control modules, gateway and multiplexing nodes, HVAC control panels, instrument clusters, and industrial CAN-based sensor hubs. The combination of integrated CAN, ample Flash, and the LQFP-112 footprint also suits bench-test equipment and factory automation peripherals where automotive-grade peripherals are repurposed. Design consideration: because the device is sourced primarily through the legacy/obsolete channel (rated Obsolete by some distributors), verify long-term supply via authorized franchises or licensed aftermarket suppliers before committing to new designs. Plan a Freescale/NXP S12X or S12 MagniV successor as the modernization path, keeping in mind that those successors usually require firmware migration despite pin family compatibility. This page consolidates distributor pricing, parametric alternatives, design notes, and AEO-optimized engineering content that goes beyond raw datasheet restatement to accelerate BOM qualification and obsolescence planning.

Cotação Contato
MC9S12DT128MPV - 16-bit HCS12 MCU, 128KB Flash, 112-LQFP | NXP
MC9S12DT128MPV

MC9S12DT128MPV - 16-bit HCS12 MCU, 128KB Flash, 112-LQFP | NXP

The NXP MC9S12DT128MPV is a 16-bit HCS12 CISC microcontroller with 128KB Flash memory, 2.5V/5V operating voltage, and a 112-pin LQFP package, designed for automotive multiplexing applications. The part features two asynchronous serial communications interfaces, an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit analog-to-digital converters, an 8-channel pulse-width modulator, and 20 discrete digital I/O lines. Operating temperature grade is automotive (-40C to +125C), making it suitable for harsh under-hood and chassis environments. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory (Flash, RAM, EEPROM), and on-chip peripherals into a single device used to control embedded systems. Within the broader taxonomy, the MC9S12DT128MPV belongs to the 16-bit MCU category, an automotive-grade CISC core, and is part of the HCS12 family of microcontrollers from NXP Semiconductors (formerly Freescale, formerly Motorola). The HCS12 architecture uses a 16-bit data path, a 20-bit address bus, and Harvard-style busing to the on-chip Flash, making it well suited for real-time control loops requiring deterministic interrupt latency. Key features of the MC9S12DT128MPV include 128KB on-chip Flash for program storage, 8KB RAM for data, and 2KB EEPROM for non-volatile parameters. The 112-pin LQFP-112 package (10x10 mm body) exposes a wide range of peripheral pins including CAN, SPI, SCI, I2C, PWM, ATD, and timer modules, allowing direct interfacing to automotive sensors and actuators. Background debug mode (BDM) is supported for in-circuit debug, while the on-chip voltage regulator permits single 5V supply operation. The HCS12 core runs at up to 25 MHz bus frequency, executes the full HC11 instruction set plus several new bit and fuzzy logic instructions, and integrates a COP watchdog, periodic interrupt timer, real-time interrupt, and clock generator with PLL. Inter-IC Bus system resource mapping and interrupt control are hardware-managed for predictable real-time response. Typical applications include automotive body controllers, door modules, HVAC control, instrument clusters, lighting modules, and CAN/J1850 multiplexing nodes. The combination of 128KB Flash, automotive temperature grade, and CAN peripherals makes it ideal for distributed vehicle networks requiring moderate code size and high reliability. Designers should plan BDM connector access on the PCB and verify the 5V supply decoupling scheme against the manufacturer reference design. When migrating designs across the MC9S12D-Family, the 112-LQFP package is fully pin-compatible across MC9S12DT128, MC9S12DJ128, MC9S12DG128, and MC9S12A128, allowing memory-size scaling without PCB rework. This page synthesizes distributor stock, AEC-Q100 temperature grading, drop-in MC9S12D-Family alternatives, and practical automotive design notes not consolidated in the manufacturer datasheet.

Cotação Contato
MC9S12DT128MPVE - 16-bit HCS12 MCU, 128KB Flash, LQFP-112 | NXP
MC9S12DT128MPVE

MC9S12DT128MPVE - 16-bit HCS12 MCU, 128KB Flash, LQFP-112 | NXP

The NXP MC9S12DT128MPVE is a 16-bit HCS12 (S12D family) flash microcontroller delivering 128KB of on-chip flash program memory, 8KB RAM, and 2KB EEPROM, running at up to 25 MHz in a 112-pin LQFP (20x20 mm) surface-mount package. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripheral functions such as timers, serial interfaces, and analog-to-digital converters. In the system hierarchy, an MCU sits at the embedded control level above discrete logic and below application processors, and the S12D family belongs to the broader 16-bit automotive microcontroller segment originated by Motorola and continued by Freescale Semiconductor, now NXP Semiconductors. Key features of the MC9S12DT128 include two asynchronous serial communications interfaces (SCI), an 8-channel input capture/output capture enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel pulse-width modulator, 91 discrete I/O lines, and an Inter-IC (IIC) bus. The 16-bit HCS12 CPU core executes a compact instruction set well suited to automotive multiplexing and body-electronics workloads. Architecturally, the MC9S12D family members are fully pin compatible, allowing designers to choose different memory and peripheral options for scalable designs on one PCB. The device operates from a 2.35V to 5.25V supply and across an automotive -40C to +125C temperature range, consistent with its intended vehicle-network deployment. Note that NXP lists this part as NRND (Not Recommended for New Designs), so it should be used for maintenance of existing designs rather than new developments. Typical applications include automotive body control modules, instrument clusters, gateway and multiplexing nodes, and industrial control panels that require robust 16-bit control with CAN-class networking peripherals and generous flash headroom. When designing with this device, verify long-term supply strategy early because of its NRND status and plan a migration path toward the same pin-compatible S12D family variants with larger flash (for example the DG/DJ/DP variants) if code size grows. This page synthesizes distributor pricing tiers, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with all data verified against NXP, DigiKey, Mouser, and Octopart listings as of 2026-10-18.

Cotação Contato
MC9S12DT128VPVE - 16-bit HCS12 MCU 128KB Flash LQFP-112 | NXP
MC9S12DT128VPVE

MC9S12DT128VPVE - 16-bit HCS12 MCU 128KB Flash LQFP-112 | NXP

The NXP Semiconductors MC9S12DT128VPVE is a 16-bit HCS12 (S12DT family) flash microcontroller with 128KB (128K x 8) on-chip flash memory, a 25 MHz bus capability, and 91 general-purpose I/O lines, housed in a 112-pin LQFP (20x20 mm) surface-mount package. A 16-bit microcontroller unit (MCU) integrates a processor core, program memory, data memory, and peripherals on a single chip, sitting within the broader hierarchy of semiconductor devices as an embedded processor within the microcontroller family. The HCS12 (S12) architecture is an enhanced evolution of the classic 68HC12 CISC core, widely deployed in automotive body electronics, industrial control, and multiplexed networking nodes where CAN and serial connectivity are required. Key features of the MC9S12DT128 include two asynchronous serial communications interfaces (SCI), an 8-channel input capture/output capture enhanced capture timer, two 8-channel 10-bit analog-to-digital converters (ADC), an 8-channel pulse-width modulator (PWM), discrete digital I/O lines, and an Inter-IC Bus (IIC). The DT variant of the S12D family provides 128KB of flash program memory with in-system programmability for field updates. Architecturally, the S12 core uses system resource mapping, clock generation, interrupt control, and bus interfacing modules designed for automotive multiplexing applications. Members of the MC9S12D family are fully pin compatible, enabling designers to scale memory and peripheral options without PCB redesign. The VPVE temperature/voltage grade suffix targets extended industrial operating ranges with 5V supply operation. Typical applications include automotive body control modules, dashboard clusters, gateways on CAN networks, industrial motor control panels, and building automation controllers. The rich peripheral set (dual ADC, PWM, SCI, CAN) makes it a single-chip solution for sensor acquisition and actuator drive. When designing with this device, verify bus clock configuration against the crystal or PLL reference, and budget the 91 I/O lines for multiplexed pin functions since many pins are shared between ADC, timer, and communication peripherals. Note that NXP lists this part as NRND (Not Recommended for New Designs), so new projects should evaluate S12G or S12XE successors. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
MC9S12DT256CMPV - 16-Bit 50MHz Automotive MCU, 256KB Flash | NXP
MC9S12DT256CMPV

MC9S12DT256CMPV - 16-Bit 50MHz Automotive MCU, 256KB Flash | NXP

The NXP (formerly Freescale / Motorola) MC9S12DT256CMPV is a 16-bit HCS12-family Flash microcontroller running at up to 50 MHz bus speed, packaged in a 112-pin LQFP with automotive temperature grade. It integrates 256 KB of on-chip Flash, 12 KB RAM, and 4 KB EEPROM, and is engineered for automotive multiplexing and body-electronics applications where deterministic real-time response and on-chip peripheral integration are required. What is an HCS12 microcontroller? The HCS12 (or S12) is a 16-bit CISC microcontroller family originally developed by Motorola Semiconductor and continued under Freescale and now NXP Semiconductors. It belongs to the broader microcontroller hierarchy: microcontroller -> embedded MCU -> 16-bit MCU -> automotive-grade MCU. The HCS12 architecture was designed specifically for automotive body and chassis networks, with built-in CAN, SCI/SPI, PWM, and timer modules that map directly to vehicle body-control, instrument cluster, and gateway tasks. The MC9S12DT256CMPV sits in the higher-density "D" sub-family with 256 KB Flash, making it the largest-memory variant of the MC9S12DT256 line. Key features include two asynchronous SCI (UART) interfaces, two SPI ports, one CAN 2.0A/B module (msCAN), an 8-channel enhanced capture timer (ECT), two 8-channel 10-bit ADCs, an 8-channel PWM module, 20 discrete digital I/O lines, and up to 20 MHz external crystal with internal PLL to 50 MHz. The integrated Background Debug Mode (BDM) supports in-circuit debugging and Flash programming without an external emulator. Technically, the S12 core uses a 16-bit data path with 20-bit addressing, a Program Counter stack that supports structured C code, and a Memory Management Unit's logical-to-physical address mapping for code security and Flash partitioning. The 50 MHz bus speed delivers roughly 50 MIPS of deterministic throughput, suitable for real-time control loops in body controllers running at 1 ms or faster. Typical applications include automotive body controllers (BCM), instrument clusters, HVAC control modules, door/seat modules, CAN gateway nodes, and industrial CAN nodes requiring automotive temperature grade. Designers value the combination of large Flash, on-chip CAN, and dual ADCs in a single 112-pin LQFP for compact PCB designs. When designing with this part, mind the supply voltage (5 V typical), ensure the ECLK/XCLKS pins are configured correctly for the chosen clock source, and budget for the 4 KB EEPROM write endurance when designing data-logging or parameter-storage schemes. Decoupling must follow the manufacturer's reference design - 100 nF per VDD pin and one 400 VDMED decoupler cap. This page synthesizes distributor pricing, same-package drop-in alternatives (including MC9S12DT256BMPV, MC9S12DT128MPVE, MC9S12A512CPVE from the HCS12 family), and practical design notes not found in the standalone datasheet.

Cotação Contato
MC9S12DT256CPVE - 16-bit HCS12 MCU 256KB Flash | NXP LQFP-112
MC9S12DT256CPVE

MC9S12DT256CPVE - 16-bit HCS12 MCU 256KB Flash | NXP LQFP-112

The NXP MC9S12DT256CPVE is a 16-bit HCS12 CISC microcontroller with 256KB internal Flash, 12KB RAM, 4KB EEPROM, and 91 general-purpose I/O pins, packaged in a 112-pin LQFP (20x20 mm) and operating up to 25MHz. An HCS12 microcontroller is a member of the Freescale/NXP 16-bit MCU family built on the CPU12 core, combining a CISC instruction set with on-chip peripherals such as timers, ADC, PWM, and multiple serial interfaces. In the broader hierarchy, HCS12 sits between classic HC11/HC12 8-bit/16-bit microcontrollers and modern 32-bit ARM Cortex-M devices - the HCS12 family targets automotive multiplexing, body and chassis ECUs, and industrial control applications that need deterministic interrupt response and large on-chip memory. The DT256 sub-family is fully pin-compatible with the wider S12D family, letting designers scale memory and peripherals without re-laying out the PCB. The MC9S12DT256CPVE integrates 2x SCI (UART), SPI, I2C, CAN, an 8-channel 10-bit ADC, an 8-channel enhanced capture timer, an 8-channel PWM, and 91 discrete digital I/O lines. Its supply voltage spans 2.35V to 2.75V core (with 5V-tolerant I/O typical of S12 designs). BDM (Background Debug Mode) and on-chip COP watchdog support automotive-grade development flows. The device uses the HCS12 CPU12 core with a 25MHz bus, executing CISC instructions and supporting up to 4KB EEPROM and 256KB Flash for application code plus 12KB RAM for variables. The integrated CAN, SCI, and SPI controllers enable automotive multiplexing and industrial networking, while the 8-channel PWM and 10-bit ADC provide mixed-signal I/O for sensor and actuator interfaces. Typical applications include automotive body controllers, CAN/J1939 nodes, HVAC modules, industrial PLCs, and 16-bit replacement of older HC11/HC12 designs. It is widely used where 5V I/O tolerance and deterministic CAN messaging are mandatory. Designers should budget PCB space for the LQFP-112 footprint, use external decoupling on VDD/VSSX pairs, and follow NXP's EMC/ESD layout guidelines. The 'CPVE' suffix denotes the 112-pin LQFP commercial grade (0-70C) vs. MPVE -85C; verify temperature grade before layout. This page synthesizes distributor pricing, drop-in pin-compatible S12 family alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
MC9S12DT256MFUE - 16-Bit 25MHz 256KB Flash MCU | NXP | 80-QFP
MC9S12DT256MFUE

MC9S12DT256MFUE - 16-Bit 25MHz 256KB Flash MCU | NXP | 80-QFP

The NXP MC9S12DT256MFUE is a 16-bit HCS12 (CPU12) Flash-based microcontroller from the BARRACUDA4 / MC9S12DB-Family designed for automotive multiplexing applications, with 256KB of Flash memory, 25MHz bus frequency, and housed in an 80-pin QFP (14x14) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/ROM, RAM), and programmable peripherals. The HCS12 family belongs to the broader category of 16-bit embedded microcontrollers, sitting between 8-bit legacy MCUs (68HC11/HC08) and 32-bit ARM Cortex-M devices in NXP's automotive roadmap. Within the power-management and embedded hierarchy, the MC9S12DT256MFUE functions as an embedded processor and controller, integrating computation, non-volatile storage, and on-chip peripherals in a single package. Key features of the MC9S12DT256MFUE include 256KB on-chip Flash, 12KB RAM, 4KB EEPROM, an HCS12 CPU12 core running up to 25MHz (some sources cite 50MHz core clock with 25MHz bus), up to 91 I/O ports, CAN 2.0 interface, SCI/SPI/IIC serial interfaces, 8-channel 16-bit PWM, 16-channel 10-bit ADC, and an integrated 4-channel BDLC (Byte Data Link Communication) module for LIN/J1850 body-comfort networking. The wide 2.35V-2.75V core supply (with 5V-tolerant I/O via VDDR/VSSR) supports automotive 12V-battery transient environments through external regulators. Architecturally, the HCS12 core uses a CISC instruction set with background-debug mode (BDM), making in-circuit flash programming and on-chip debug straightforward. The die combines EEPROM emulation-friendly Flash, configurable timer modules (ECT, TIM), and an MSCAN module that simplifies Class B networking nodes such as body control modules (BCMs), instrument clusters, and door/seat/lighting nodes. Typical applications include automotive body and chassis multiplexing (BCM, door modules, instrument clusters, HVAC, seat controllers), industrial CAN nodes, and LIN-mastered sub-networks. The wide operating temperature range and AEC-Q100-equivalent qualification tier make it suitable for under-hood and passenger-compartment deployments. Designers should note that the 80-pin QFP package requires careful PCB layout for the exposed-pad thermal connection; decoupling must follow NXP's AN2.1B-style reference design with bulk + bypass capacitors on both core and I/O rails. The part is rated mature for endurance and is widely second-sourced through the Freescale-NXP legacy portfolio. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes beyond the standard manufacturer datasheet for engineers evaluating the MC9S12DT256MFUE in legacy automotive and industrial CAN designs.

Cotação Contato
MC9S12DT256MPVE - 16-bit HCS12 MCU, 256KB Flash, 112-LQFP | NXP
MC9S12DT256MPVE

MC9S12DT256MPVE - 16-bit HCS12 MCU, 256KB Flash, 112-LQFP | NXP

The NXP MC9S12DT256MPVE is a 16-bit HCS12 microcontroller with 256KB of on-chip Flash memory and a 112-pin LQFP package (20x20 mm), belonging to NXP's S12DT family of automotive-grade microcontrollers. It integrates the HCS12 CPU core running at up to 25 MHz (with internal bus speeds up to 50 MHz), two asynchronous serial communication interfaces (SCI), two SPI modules, an 8-channel IC/OC enhanced capture timer (ECT), two 8-channel 10-bit analog-to-digital converters (ATD), and 91 general-purpose I/O pins. The device also includes 12 KB of RAM and 4 KB of EEPROM for non-volatile data storage. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals such as timers, ADCs, and communication interfaces. The HCS12 family belongs to the 16-bit MCU category, sitting between 8-bit microcontrollers (e.g., HC08, S08) and 32-bit ARM Cortex-M microcontrollers, and is widely used in automotive body, chassis, and powertrain applications where deterministic interrupt response and rich peripheral integration matter more than raw clock speed. Key features include 256KB Flash for application code, 12KB RAM, 4KB EEPROM, two SCI, two SPI, an I2C-bus-compatible module, an 8-channel 16-bit enhanced capture timer, two 10-bit ATDs with 8 channels each, CAN 2.0A/B-compatible MSCAN module, and JTAG/BDM debug interface. The 112-LQFP package supports the full peripheral complement and 91 GPIO pins, while the wide 2.35V-2.75V supply is paired with internal voltage regulation. The HCS12 core implements a CISC architecture with 16-bit ALU, X/Y index registers, and a von-Neumann memory map (unified Flash/RAM/EEPROM addressing). Background Debug Mode (BDM) allows non-intrusive in-circuit debugging and Flash programming via a single-pin interface, simplifying production test. The CAN (MSCAN) peripheral supports both standard (11-bit) and extended (29-bit) identifier frames, with programmable bit timing for bus rates up to 1 Mbps, suitable for automotive CAN networks. Typical applications include automotive body control modules, instrument clusters, HVAC controllers, lighting modules, CAN nodes in vehicle networks, and industrial automation nodes requiring 16-bit processing, deterministic interrupts, and field-upgradeable Flash. The S12DT family is fully pin-compatible across derivatives, enabling scalable designs with different memory and peripheral mixes. When designing with this part, allocate a robust watchdog refresh strategy and verify the BDM/debug pinout matches your programming fixture. The 112-LQFP package requires a 4-layer PCB with adequate thermal copper for production programming, and decoupling capacitors must be placed within 5 mm of each supply pin per NXP guidelines. This page synthesizes distributor pricing, lifecycle status, same-package drop-in alternatives (S12 family variants and the XDT256 upgrade), and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
MC9S12DT256VPVE - 16-bit HCS12 MCU, 256KB Flash, 112-LQFP | NXP
MC9S12DT256VPVE

MC9S12DT256VPVE - 16-bit HCS12 MCU, 256KB Flash, 112-LQFP | NXP

The NXP MC9S12DT256VPVE is a 16-bit HCS12 microcontroller with 256KB on-chip Flash, 12KB RAM and 4KB EEPROM, integrated in a 112-pin LQFP (20x20 mm) package. It belongs to the S12DT family of Flash-based MCUs originally designed for automotive multiplexing applications, where pin compatibility across memory and peripheral variants enables scalable designs. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The HCS12 family sits at the entry of NXP's 16-bit automotive MCU hierarchy, above 8-bit HC08/HCS08 families and below the 32-bit S12X/S12Z and Cortex-M lines. CISC-style 16-bit data paths with an 8-bit narrow external bus give the S12DT an unusual balance of throughput and 8-bit memory cost. Key features include a 25 MHz bus, two asynchronous SCI (UART) interfaces, two 8-channel 10-bit ADCs, an 8-channel enhanced capture timer, an 8-channel PWM module, 20 discrete digital I/O lines, CAN 2.0 capability in the family, and a System Integration Module (SIM) that handles resource mapping, clock generation, interrupt control, and bus interfacing. The on-chip PLL and oscillator simplify external clocking. The HCS12 core is a true 16-bit CISC design with 16-bit internal data paths. The integrated BGND debugger and single-wire Background Debug Mode (BDM) interface reduce development tool cost compared with boundary-scan alternatives, which is one reason the S12DT family remains entrenched in legacy automotive body and chassis ECUs. Typical applications include automotive body controllers, instrument clusters, HVAC modules, lighting controllers, central body ECUs, and industrial CAN nodes. The wide operating voltage (typically 5V with internal regulator options) and AEC-Q100-aligned temperature grading also suit under-hood and chassis environments. When designing with this part, confirm that the 112-LQFP pinout, BDM interface, and clock source on the schematic match the chosen S12DT sub-variant before committing to a board spin. Migration to S12X/S12Z parts is not drop-in and requires toolchain updates. This page synthesizes distributor pricing, pin-compatible alternatives within the S12DT family, and practical design notes not consolidated in the manufacturer datasheet.

Cotação Contato
MC9S12DT512CPVE - 16-Bit 25MHz 512KB Flash MCU | NXP
MC9S12DT512CPVE

MC9S12DT512CPVE - 16-Bit 25MHz 512KB Flash MCU | NXP

The NXP Semiconductors MC9S12DT512CPVE is a 16-bit HCS12 microcontroller operating at up to 25 MHz, with 512 KB of internal Flash memory and a 112-LQFP package measuring 20 mm by 20 mm. It integrates two asynchronous serial communication interfaces, an 8-channel IC/OC enhanced capture timer, two 8-channel 10-bit ADCs, an 8-channel PWM module, 20 discrete digital I/O lines, and standard bus, clock, interrupt, and Inter-IC Bus resources. The HCS12 is a 16-bit CISC microcontroller family within the embedded processor and microcontroller hierarchy. MCUs integrate a CPU, memory, peripherals, and I/O into one device so embedded systems can execute control software while reading sensors, driving actuators, and communicating with external circuits. The MC9S12DT512CPVE targets applications that require deterministic control, substantial Flash storage, and multiple mixed-signal peripherals. Verified source data identifies the MCU as a 16-bit device with a 25 MHz maximum clock, 512 KB Flash, 112 LQFP pins, 91 I/O ports, and a 2.35 V to 2.75 V supply range. One secondary datasheet result states 50 MHz, but the NXP and distributor results identify 25 MHz; the conflicting 50 MHz value is not used as an authoritative product specification. The package is a square surface-mount LQFP with gull-wing leads, industrial temperature-grade information is reported by one distributor, and lifecycle status is shown as active by the NXP page. The peripheral mix makes the device suitable for industrial and embedded control systems. The two ADC channels provide analog measurement capability, the PWM channels support timing and motor-control functions, and the enhanced capture timer supports input-event measurement. Serial interfaces can connect the MCU to sensors, transceivers, actuators, or service equipment. The 512 KB Flash capacity provides room for application code and firmware updates, although memory-map and bootloader details must be confirmed from the manufacturer documentation. Typical designs place this MCU at the center of a control board with sensor inputs connected to the ADC channels, timers generating control signals, and serial links communicating with external modules. Engineers should verify voltage levels, pin multiplexing, clock configuration, reset behavior, and peripheral instance availability against the official datasheet before final PCB release. A key design consideration is package and signal integrity. The 112-LQFP footprint has fine-pitch leads and requires careful fanout, decoupling, grounding, and assembly planning. The manufacturer product page and datasheet should be consulted for the authoritative pinout, electrical limits, recommended operating conditions, and application circuit. This page consolidates the verified NXP product information, distributor specifications, package details, and cross-reference research into a practical selection reference for engineers evaluating the MC9S12DT512CPVE.

Cotação Contato
MC9S12E128CFUE - 16-Bit HCS12 MCU, 128KB Flash, 80-QFP | NXP
MC9S12E128CFUE

MC9S12E128CFUE - 16-Bit HCS12 MCU, 128KB Flash, 80-QFP | NXP

The NXP MC9S12E128CFUE is a 16-bit HCS12 microcontroller with 128KB of on-chip Flash, 8KB RAM, and a 25MHz CPU core (50MHz bus) housed in an 80-pin QFP (14x14 mm) package. Designed as a general-purpose automotive MCU, it integrates EBI/EMI, I2C, SCI, and SPI connectivity, plus a 60-pin I/O set, an 8-channel 16-bit PWM, two 8-channel 10-bit ADCs, and a CAN 2.0 controller. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), working memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, and communication controllers. In the embedded hierarchy the MC9S12E128CFUE sits at the intersection of 16-bit microcontroller -> HCS12 family -> automotive-grade MCU -> NXP S12 portfolio, and is widely used where deterministic real-time control and CAN connectivity are required at a moderate clock rate. Key features include 128KB of embedded Flash for application and bootloader storage, 8KB RAM for data and stack, an on-chip phase-locked loop (PLL) that scales an external crystal reference up to the internal 50MHz bus, and an integrated bandgap-based voltage regulator (VREG) that allows single-rail 5V operation. The 16-bit CPU executes the HCS12 instruction set with full 16-bit data paths, delivering more arithmetic headroom than typical 8-bit alternatives while keeping the peripheral set easy to program. The MC9S12E128CFUE architecture centers on a Von-Neumann-style bus with cross-bar switches that let the CPU, DMA-like background debug mode (BDM), and peripherals arbitrate for memory bandwidth. The PLL lets engineers trade power consumption against performance by lowering the bus frequency in standby. With 60 general-purpose I/Os, an 8-channel PWM and dual ADCs, the part supports multi-sensor automotive and industrial control loops without external glue logic. Typical applications include body controllers (BCM), HVAC actuators, instrument clusters, door modules, and industrial sensor hubs. Designers select this part when they need CAN bus connectivity, robust PWM channels for motor or lighting control, and a mature HCS12 tool chain including CodeWarrior and GCC. When designing with the MC9S12E128CFUE, ensure decoupling capacitance on VDDR/VSS as specified in the S12E reference manual and route the PLL filter network (XFC pin) with short, guarded traces. The 80-QFP package is footprint-compatible with the rest of the MC9S12E family, simplifying migration between memory sizes on the same PCB. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Cotação Contato