Microcontroladores

Produtos (20.000+)

MPC8313CZQAFFB - PowerQUICC II Pro MPU, 333MHz, 516-TEPBGA | NXP
MPC8313CZQAFFB

MPC8313CZQAFFB - PowerQUICC II Pro MPU, 333MHz, 516-TEPBGA | NXP

The NXP MPC8313CZQAFFB is a PowerPC e300c3 microprocessor from the MPC83xx family, integrating a single 32-bit core running at 333 MHz in a 516-pin TEPBGA package measuring 27 x 27 mm. This Rev 2.1 silicon variant is offered without encryption and combines a cost-effective host processor architecture with low-power operation and highly integrated peripherals for embedded networking and industrial control. An MPU (Microprocessor Unit) is a system-on-chip that integrates one or more processor cores, cache, memory controllers, and peripheral interfaces into a single device. The PowerQUICC II Pro family belongs to the broader PowerPC/e300 hierarchy and is positioned between general-purpose microcontrollers and high-performance application processors, providing deterministic performance for communications and storage infrastructure. The MPC8313 specifically targets cost-sensitive designs where the integrated QUICC Engine RISC communications accelerator offloads protocol processing from the host core. Key features of the MPC8313CZQAFFB include the e300c3 core with 16 KB instruction and 8 KB data L1 caches, a 32-bit DDR1/DDR2 memory controller supporting up to 333 MHz operation, dual 10/100/1000 Mbps Ethernet controllers with SGMII and TBI interfaces, a PCI Express interface, USB 2.0 with PHY, local bus, and DUART. Security accelerators and the encryption block are intentionally omitted in the 'C' (non-E) part number suffix, reducing BOM cost versus the 'E' variants. Architecturally, the MPC8313 uses a hierarchical bus structure connecting the e300c3 core to L2 cache, the system bus, and the QUICC Engine subsystem. The QUICC Engine RISC controller handles serial protocols including HDLC, ATM, and Ethernet, allowing the host CPU to focus on application and control-plane processing. This hardware-based protocol offload yields deterministic throughput without consuming host MIPS. Typical applications include industrial control gateways, low-density routers and switches, network-attached storage controllers, factory automation nodes, and print/image processing controllers where the device's combination of Ethernet, PCI Express, and DDR2 memory support reduces overall system BOM. The 27 x 27 mm 516-ball TEPBGA package requires multilayer PCB design with controlled-impedance routing and proper thermal management under sustained load. When designing with the MPC8313CZQAFFB, verify that the power supply rails (1.0 V core, 1.8 V/2.5 V DDR, 3.3 V I/O) are sequenced correctly per the hardware specification and that the thermal solution can dissipate the typical 2 W to 4 W power envelope in the target enclosure. The non-encryption variant is recommended for cost-sensitive designs that do not require IPSec or other cryptographic acceleration. This page synthesizes distributor pricing, drop-in Rev 2.1 same-family alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Cotação Contato
MPC8313CZQAFFC - PowerQUICC II Pro 333MHz SoC MPU | NXP
MPC8313CZQAFFC

MPC8313CZQAFFC - PowerQUICC II Pro 333MHz SoC MPU | NXP

The NXP MPC8313CZQAFFC is a PowerQUICC II Pro integrated communications processor featuring a 32-bit Power Architecture e300c3 core running up to 333 MHz, integrated DDR1/DDR2 memory controller, PCI interface, Gigabit Ethernet, and USB 2.0 connectivity, packaged in a 516-ball TE-PBGA II (27 x 27 mm, 1 mm pitch). It combines a cost-effective, low-power, highly integrated system-on-chip (SoC) architecture with the classic PowerQUICC peripheral set, targeting wired communications and embedded control applications. An MPU (Microprocessor Unit) is a system-on-chip that integrates a CPU core, memory controller, and a rich peripheral set into a single package. PowerQUICC II Pro is part of NXP's PowerQUICC family — a hierarchy that spans communications processors -> SoC -> microprocessor -> integrated circuit. The MPC8313 specifically targets cost-sensitive networking and industrial designs that require GbE and USB without the cost of a full PowerQUICC III device. Key features include the e300c3 32-bit Power Architecture core with MMU and FPU, hardware acceleration for common networking tasks, dual 10/100/1000 Ethernet MACs (one RGMII/RTBI + one SGMII capable), USB 2.0 high-speed host/device, 32-bit PCI 2.3 bus interface, DDR1/DDR2 SDRAM controller up to 266 MHz, and four DMA channels. Operating temperature range is -40C to +105C (industrial), making the part suitable for harsh-environment deployments. Architecture depth: the MPC8313 integrates the e300c3 core with a 16 KB I-cache and 16 KB D-cache, plus a unified 256 KB internal SRAM block used by the QUICC Engine for protocol acceleration. The QUICC Engine technology offloads frame processing from the core, allowing line-rate Gigabit Ethernet forwarding with minimal CPU loading. The device uses a 1 V core supply with 1.5 V/1.8 V DDR memory I/O. Typical applications include integrated services routers, industrial gateways, networked printers, VoIP/ATA adapters, and factory automation controllers. The combination of GbE, USB, and PCI bridges a wide variety of embedded networking scenarios. Design consideration: the 516-ball TE-PBGA II package requires careful PCB layout with controlled-impedance traces for DDR memory and RGMII Ethernet. Designers should follow NXP's reference design guidance for power sequencing and thermal management — the device can dissipate 3-5 W under full load and benefits from thermal vias under the exposed die pad. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone, enabling engineers to evaluate fit, supply risk, and second-source options for the MPC8313CZQAFFC.

Cotação Contato
MPC8313CZQAGDC - 400MHz PowerQUICC II Pro MPU, 516-BGA | NXP
MPC8313CZQAGDC

MPC8313CZQAGDC - 400MHz PowerQUICC II Pro MPU, 516-BGA | NXP

The NXP MPC8313CZQAGDC is a PowerQUICC II Pro MPC83xx microprocessor built on the PowerPC e300c3 core, running at 400MHz with a 32-bit RISC architecture and fabricated in a 0.09-micron CMOS process. The device operates across 1.8V/2.5V/3.3V mixed-voltage rails and is housed in a 516-pin TEPBGA (27mm x 27mm) exposed-pad package rated for the -40C to +105C extended industrial temperature range. What is an MPU (Microprocessor Unit)? An MPU is a CPU-centric processor that requires external memory and peripherals, distinguishing it from a microcontroller (MCU) that integrates memory and I/O on-chip. The MPC8313CZQAGDC belongs to the broader hierarchy of MPU -> embedded processor -> application-specific SoC -> semiconductor IC. PowerQUICC II Pro devices integrate a PowerPC core with a Communication Processor Module (CPM) for high-bandwidth I/O offload, targeting routers, switches, and industrial gateways where deterministic networking is mandatory. Key features include DDR1/DDR2 memory controller support, integrated Gigabit Ethernet MAC, USB 2.0 (full-speed), PCI 2.3 interface, and dual I2C. The 400MHz core delivers approximately 600 MIPS while the CPM offloads packet processing, frame management, and serial protocol handling. The device supports the QUICC Engine for HDLC, ATM, and Ethernet bridging typical of telecom infrastructure. The MPC8313CZQAGDC uses a superscalar PowerPC core with dual-issue execution, 16KB instruction cache and 16KB data cache, MMU for full virtual memory support, and dedicated CPM peripherals connected via on-chip bus. The 0.09-micron process reduces core power versus prior 0.13-micron designs while preserving the legacy PowerQUICC software ecosystem, enabling easy migration from MPC8247/MPC8250 designs. Typical applications include industrial routers, residential gateways, networked print servers, factory automation controllers, and low-end wireless base stations. The integrated GbE and PCI make it a single-chip control-plane solution for branch-office networking and embedded NAS appliances. AEC-Q100 grade is not offered - the part targets industrial and commercial systems. When designing with this device, allocate a 4-layer PCB with continuous ground and power planes to manage the 516-ball BGA fan-out. Decouple the 1.8V, 2.5V, and 3.3V rails independently and follow NXP hardware design guidelines for DDR2 trace-length matching. Boot configuration pins must be pulled correctly before RESET deassertion. This page synthesizes distributor pricing, cross-brand drop-in equivalents, and practical design notes not consolidated in the manufacturer datasheet, helping procurement and engineering teams evaluate the MPC8313CZQAGDC against available alternatives.

Cotação Contato
MPC8313ECVRADDB - PowerQUICC II Pro MPU, 267MHz, 516-TEPBGA | NXP
MPC8313ECVRADDB

MPC8313ECVRADDB - PowerQUICC II Pro MPU, 267MHz, 516-TEPBGA | NXP

The NXP MPC8313ECVRADDB is a PowerQUICC II Pro microprocessor (MPU) based on the PowerPC e300c3 core, delivering 267 MHz performance in a 516-ball TEPBGA (27x27 mm) package. It integrates a 32-bit RISC CPU with a built-in security accelerator (SEC 2.x) for hardware-accelerated encryption, making it suitable for secure networking and edge applications. The device supports multiple power domains at 1.8V/2.5V/3.3V I/O and operates across an industrial temperature range. An MPU (microprocessor unit) in the PowerQUICC family is an integrated communications processor that combines a CPU core with peripheral controllers such as Ethernet MACs, UARTs, I2C, SPI, and DDR memory controllers. The MPC8313E belongs to the PowerQUICC II Pro hierarchy: MPU -> communications processor -> embedded processor -> integrated circuit. This places it firmly in the networking-infrastructure tier of NXP's portfolio, optimized for low-cost, low-power secure routers, NAS appliances, and industrial gateways. Key features include a 16 KB instruction cache and 16 KB data cache with Harvard architecture, hardware encryption (DES, 3DES, AES, SHA-1/MD5, ARC4), dual 10/100/1000 Ethernet MACs via the TSEC interface, DDR1/DDR2 memory controller, PCI Express and PCI interfaces, plus USB 2.0 (host/device). The on-chip security engine offloads crypto from the e300c3 core, freeing CPU cycles for protocol processing. Architecturally, the MPC8313E uses a 90 nm CMOS process and pairs the e300c3 core with a high-bandwidth internal bus (the coherency module) that ties together the SEC, Ethernet, DDR, and local-bus peripherals. The integrated QUICC Engine technology (inherited from the PowerQUICC lineage) handles common serial protocols including HDLC, TDM, and ATM. Compared with discrete CPU-plus-ASIC designs, the MPC8313E reduces BOM cost and PCB area while maintaining deterministic real-time behavior. Typical applications include home gateways and SOHO routers with VPN/IPsec, networked attached storage (NAS) controllers, secure industrial control gateways, factory-floor protocol converters (Modbus/TCP, PROFINET), and embedded firewalls. The encryption accelerator is particularly valuable for any application that must terminate IPsec, SSL/TLS, or MACsec tunnels at line rate without burdening the application CPU. Designers should plan thermal dissipation for the 27x27 mm BGA using a 4-6 layer board with a continuous ground plane under the package. The DDR reference clock and Ethernet MII/RGMII traces require controlled impedance routing (50 ohm single-ended, 100 ohm differential). Bootstrap configuration pins sampled at POR determine boot source, CPU-to-bus clock ratio, and endian mode and must be pulled high or low through 4.7 kohm resistors. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes beyond what is presented in the NXP hardware datasheet, giving procurement and design engineers a single source for part selection.

Cotação Contato
MPC8313ECVRADDC - PowerQUICC II Pro SoC 267MHz | NXP
MPC8313ECVRADDC

MPC8313ECVRADDC - PowerQUICC II Pro SoC 267MHz | NXP

The NXP MPC8313ECVRADDC is a PowerQUICC II Pro Power Architecture system-on-chip integrating an e300c3 core running at 267 MHz with 32-bit RISC performance, DDR1/DDR2 memory controller, PCI interface, Gigabit Ethernet, USB 2.0, and security engine (SEC) acceleration in a 516-pin TEPBGA package (27x27 mm) operating from -40C to +105C. The part belongs to NXP's MPC8313E family (Rev 3.0 silicon) and is qualified for industrial temperature ranges. A PowerQUICC II Pro SoC (System-on-Chip) is a communications-centric processor that combines a Power Architecture CPU with dedicated networking and security peripherals on a single die. The MPC83xx family hierarchy places MPC8313E below higher-end MPC8323/MPC8349 devices while above the MPC8314/MPC8315 cost-down variants, all targeting SOHO/SMB routers, industrial gateways, and secure print/imaging equipment. The integrated security engine offloads DES, 3DES, AES, SHA-1/MD5 hashing, and public-key arithmetic from the host CPU, enabling wire-speed VPN termination and IPsec acceleration. Key features include a 32-bit PowerPC e300c3 core with MMU and unified L1 caches, hardware encryption engine, dual 10/100/1000 Ethernet MACs with integrated SerDes, USB 2.0 High-Speed host/device/OTG, 32-bit PCI 2.3 interface, DDR1/DDR2 SDRAM controller with ECC support up to 266 MHz, local bus controller, four DMA channels, and dual I2C, SPI, and UART peripherals. Power consumption is typically below 5 W at full CPU and I/O load. Architecturally, the device pairs a single-issue, dual-issue capable PowerPC core with a coherent system bus connecting the DDR controller, DMA engine, and peripheral bridges. The security engine runs on a dedicated coprocessor interface, allowing cryptographic operations to occur in parallel with packet processing on the QUICC Engine subsystem. This partitioning delivers deterministic networking throughput independent of application-level CPU load. Typical applications include SOHO routers, VPN/IPsec gateways, industrial Ethernet switches, secure print controllers, network-attached storage (NAS), and factory automation controllers. The wide industrial temperature range and integrated encryption make it particularly suitable for hardened networking equipment deployed in outdoor enclosures or factory floors. When designing with this device, follow the NXP reference design for PCB layout: allocate a 4-layer stackup with dedicated ground planes under the BGA, place 100 nF decoupling on every power pin, and route DDR traces with matched lengths within 25 mils. Use the internal PHY only for copper connections below 100 m; for fiber uplinks, route through the SGMII interface to an external SerDes. This page synthesizes authorized distributor pricing, drop-in alternative listings, and PCB layout guidance beyond the manufacturer datasheet to accelerate your bring-up.

Cotação Contato
MPC8313ECVRAFF - PowerQUICC II Pro MPU, 333 MHz, 516-TEPBGA | NXP
MPC8313ECVRAFF

MPC8313ECVRAFF - PowerQUICC II Pro MPU, 333 MHz, 516-TEPBGA | NXP

The NXP MPC8313ECVRAFF is a PowerQUICC II Pro host processor built around the PowerPC e300c3 core, delivering 333 MHz of 32-bit processing performance in a 516-TEPBGA (27x27 mm) package. It integrates a DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs (one with security acceleration), USB 2.0, four UARTs, two I2C, SPI, local bus, PCI Express, and a programmable interrupt controller, providing a complete system-on-chip solution for cost-sensitive networking and industrial control applications. The integrated security engine (SEC 2.3) accelerates IPSec, SSL, and other cryptographic protocols without external crypto hardware, while dual Gigabit Ethernet controllers enable line-rate packet processing for SOHO/SMB routers, switches, and industrial gateways. What is a PowerQUICC II Pro processor? PowerQUICC II Pro is NXP's family of PowerPC-based communications processors that evolved from the original PowerQUICC architecture. The PowerQUICC II Pro platform sits within the broader MPU (microprocessor unit) hierarchy: MPU -> embedded processor -> PowerPC architecture -> PowerQUICC II Pro family. These MPUs are specifically architected for protocol processing, packet routing, and secure networking termination, making them distinct from general-purpose ARM Cortex MPUs. Key features include a 333 MHz e300c3 core with 16 KB I-cache and 16 KB D-cache, integrated 32-bit DDR1/DDR2 SDRAM controller up to 333 MHz, hardware cryptography accelerator, dual 10/100/1000 Ethernet MACs, USB 2.0 device/host with on-chip PHY, four DMA channels, and PCI Express endpoint support. The 516-TEPBGA package provides ample I/O with 27 mm x 27 mm body dimensions and 1 mm pitch, supporting high-density networking designs. The e300c3 core is a superset of the PowerPC Book-E architecture with signal processing extensions and core-complex break-point debug support. The integrated security engine delivers up to 1 Gbps IPSec throughput, enabling secure VPN termination without off-chip accelerator silicon. Multi-port Ethernet switching fabric with QoS support makes it suitable for managed switch and router designs. Typical applications include SOHO/SMB routers and gateways, secure VPN concentrators, industrial control with Ethernet connectivity, network-attached storage (NAS), and IP-PBX/media gateways. Designers choose the MPC8313E for its favorable cost-per-port ratio when Gigabit Ethernet and security processing are required without external coprocessors. When designing with this device, ensure the four-layer PCB stack-up meets DDR2 SI requirements and that the JTAG debugging interface is accessible in production units. The BGA package requires X-ray inspection post-reflow and the device thermal envelope (junction 0 to 105 C) requires adequate airflow in enclosed networking enclosures. This page synthesizes NXP datasheet parameters, drop-in alternatives within the PowerQUICC II Pro family, and practical design notes not found in the manufacturer datasheet.

Cotação Contato
MPC8313ECZQAFFB - 333MHz PowerQUICC II Pro MPU | NXP
MPC8313ECZQAFFB

MPC8313ECZQAFFB - 333MHz PowerQUICC II Pro MPU | NXP

The NXP MPC8313ECZQAFFB is a cost-effective, low-power PowerQUICC II Pro host processor built on the PowerPC e300c3 core, operating at up to 333 MHz with a 32-bit data bus. Housed in a 516-ball TE-PBGA package (27x27 mm) with exposed pad, the device integrates a hardware security engine for encrypted communications alongside the standard MPC83xx peripherals, making it well suited for secure networking and industrial gateway designs. A microprocessor (MPU) is a single-chip CPU that integrates core, cache, memory controller and I/O peripherals. The e300c3 core executes the PowerPC instruction set with a 32-Kbyte L1 instruction cache and a 32-Kbyte L1 data cache, and the MPC8313E adds on-chip encryption acceleration - a feature not present on the non-E variant. Key features of the MPC8313E include a 333 MHz core, a DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs (one RGMII and one SGMII interface selectable), a USB 2.0 (Full/Low Speed) controller, a local bus controller, dual I2C, SPI, dual UART, GPIOs, and a NAND flash controller (FCM). The dedicated security engine accelerates DES, 3DES, AES, and public-key algorithms, offloading cryptographic load from the core. The architecture combines an e300c3 superscalar core with on-chip accelerated engines and the well-known QUICC Engine subsystem for protocol handling. Multiple power domains (1.0 V core plus selectable 1.8 V / 2.5 V / 3.3 V I/O) reduce total system power, and four GMII-style Ethernet paths support line-rate switching or routing duties at gigabit speeds when used with an external PHY. Typical applications include secure industrial gateways, networked printers, SOHO routers and VPN access concentrators, NAS controllers, and small-form-factor NAS or print servers. The combined dual GbE + USB 2.0 + NAND support enables a complete wired networking appliance on a single chip. When designing with this device, allocate the 27x27 mm TE-PBGA footprint with sufficient PCB layers (typically 6-8) for power, ground, and the matched-impedance DDR2 traces. Thermal management relies on the exposed pad soldered to a continuous ground plane; without this, junction-to-ambient resistance rises dramatically and the security accelerator duty cycle must be derated. This page synthesizes distributor pricing, drop-in alternatives from the same MPC8313 family, and practical design notes not found on a single manufacturer product page.

Cotação Contato
MPC8313ECZQAFFC - PowerQUICC II Pro 333MHz SoC MPU | NXP
MPC8313ECZQAFFC

MPC8313ECZQAFFC - PowerQUICC II Pro 333MHz SoC MPU | NXP

The NXP MPC8313ECZQAFFC is a PowerQUICC II Pro integrated communications processor that combines a PowerPC e300c3 core running at 333 MHz with a 516-TEPBGA (27x27 mm) package. It integrates DDR1/DDR2 memory support, PCI, Gigabit Ethernet, USB 2.0, and a Security Engine (SEC) for embedded networking applications in a single -45 GHz processing device. What is an MPU (Microprocessor Unit)? An MPU is an integrated circuit that contains a CPU core and integrated peripherals such as memory controllers and communications interfaces. The PowerQUICC family is a hierarchy of Power Architecture SoCs from NXP (formerly Freescale), descended from the original PowerQUICC I and PowerQUICC II communications processors used widely in routers, switches, and industrial gateways. The MPC8313 specifically belongs to the MPC83xx sub-family, integrating more peripherals than its predecessors while keeping the classic PowerQUICC architecture for software reuse. Key features include a single e300c3 core at 333 MHz, 16 KB I-cache and 16 KB D-cache, integrated DDR1/DDR2 memory controller supporting up to 256 MB, dual 10/100/1000 Ethernet MACs with TCP/IP acceleration, USB 2.0 high-speed host/device, PCI 2.3 interface, and a hardware Security Engine for DES, 3DES, AES, and MD5/SHA-1 hashing. The 0.95 V to 1.05 V core supply and -40C to +105C industrial temperature range suit industrial and rugged environments. Technical depth: The MPC8313 uses a 90 nm process and replaces an external Northbridge by integrating the DDR controller, three Fast Ethernet controllers, a PCI controller, and the Security Engine. The QUICC Engine multi-protocol block handles TDM, HDLC, and ATM, making the device well-suited for legacy telecom and industrial control applications. The integrated SEC block offloads cryptographic work from the host CPU. Typical applications include industrial gateways, wireless LAN access points, multi-function printers, network attached storage, and telecom DSL line cards. The integrated GbE switch fabric and Security Engine make it suitable for VPN, IPsec, and SSL/TLS acceleration in routers and firewalls. When designing with this device, ensure the 0.95-1.05 V core supply is sequenced before the 1.8 V/2.5 V DDR I/O supply, use impedance-controlled PCB traces for DDR and Gigabit Ethernet, and provide adequate decoupling near the BGA balls. Software reuse from the PowerQUICC II Pro family (U-Boot, Linux 2.6, VxWorks BSPs) accelerates development. This page synthesizes distributor pricing, parametric comparisons, drop-in alternatives, and design considerations not found in the manufacturer datasheet alone.

Cotação Contato
MPC8313EVRADDB - PowerPC e300c3 MPU 267MHz 516-BGA | NXP
MPC8313EVRADDB

MPC8313EVRADDB - PowerPC e300c3 MPU 267MHz 516-BGA | NXP

The NXP MPC8313EVRADDB is a PowerPC e300c3 microprocessor IC from the MPC83xx family with a single 32-bit core running at 267 MHz, housed in a 516-ball TEPBGA (27x27 mm) package. The part integrates an integrated security engine (indicated by the "E" in the part number), a DDR1/DDR2 memory controller, dual Gigabit Ethernet controllers with SGMII support, USB 2.0 high-speed interface, and a local bus controller. It is designed for cost-sensitive networking, industrial control, and secure connected applications where board real-estate and power budget are key constraints. Background: An MPU (Microprocessor Unit, also called microprocessor IC) is a standalone processor IC, distinct from a microcontroller (MCU), which typically includes on-chip flash memory and peripherals. The MPC83xx line sits at the intersection of networking-grade processing and Power Architecture, originally developed by Freescale and now part of NXP's Power Architecture (e.Power) portfolio. The e300c3 core implements the Power Architecture Book-E instruction set with hardware cryptography acceleration, positioning the MPC8313 family as a secure platform for embedded routers, NAS systems, and industrial gateways. Key differentiators include integrated encryption acceleration (SEC 2.3+), dual Gigabit Ethernet MACs, USB 2.0 high-speed (480 Mbps), and DDR1/DDR2 memory support up to 256 MB. The MPC8313EVRADDB operates from a 1.0 V core supply and 1.8/2.5 V for DDR, supporting industrial temperature ranges. The 27x27 mm 516-TEPBGA package features an exposed thermal pad enabling efficient heat dissipation in space-constrained designs. Typical applications include secure routers, network attached storage (NAS), industrial automation controllers, secure point-of-sale terminals, and embedded gateways. The SGMII-capable Gigabit Ethernet ports and hardware encryption acceleration make it particularly suitable for managed switches and VPN appliances. Design consideration: Power-rail sequencing (1.0 V core before 1.8/2.5 V I/O) is required during power-up to prevent latch-up. PCB designers must allocate at least 6 layers with dedicated power planes and follow the NXP layout guidelines for DDR trace matching within 50 ps. This page synthesizes distributor pricing, same-family alternatives, and applied design considerations curated for embedded engineers evaluating the MPC8313 platform - context not available in a single distributor listing.

Cotação Contato
MPC8313EVRAFF - PowerPC e300c3 MPU 333MHz 516-TEPBGA | NXP
MPC8313EVRAFF

MPC8313EVRAFF - PowerPC e300c3 MPU 333MHz 516-TEPBGA | NXP

The NXP MPC8313EVRAFF is a PowerPC e300c3 microprocessor from the PowerQUICC II Pro family, delivering 333 MHz core performance with security/encryption acceleration in a 516-ball TEPBGA package (27x27 mm). It integrates a 32-bit PowerPC core, dual 10/100/1000 Ethernet MACs, a DDR1/DDR2 memory controller, 16-bit local bus, and an integrated security engine (SEC 2.3) for IPSec, SSL/TLS, SRTP, 3GPP, IEEE 802.11i, and other cryptographic protocols. What is a PowerQUICC II Pro processor? PowerQUICC II Pro is NXP/Freescale's family of integrated communications processors that combine a PowerPC host core with dedicated communication peripherals. These devices sit within the broader taxonomy of embedded microprocessors (MPU) -> communications processors -> networking SoCs. They are designed for cost-sensitive networking, industrial, and storage applications where deterministic data-plane performance and rich I/O integration eliminate the need for external bridges and ASICs. Key features include 333 MHz e300c3 core, 16 KB I-cache and 16 KB D-cache, 32-bit DDR1/DDR2 memory controller with ECC, dual Gigabit Ethernet MACs with QoS, USB 2.0 (full/low speed), two Enhanced Local Bus controllers, 4-channel DMA, IEEE 1588 timestamp support, and an integrated security accelerator that off-loads DES/3DES/AES/SHA-1/MD5/RSA/ECC operations from the host CPU. The architecture pairs a classic Book-E PowerPC core with a system-on-chip peripheral set, allowing OEMs to build single-BOM designs that route gigabit traffic, terminate IPSec tunnels, and run Linux or VxWorks without external coprocessors. The integrated RGMII interfaces simplify PHY connection, while the SEC engine sustains multi-hundred-megabit encrypted throughput that a software-only stack on the e300c3 core cannot match. Typical applications include industrial Ethernet routers and gateways, low-end branch-office VPN routers, secure access points, networked industrial controllers, SOHO NAS heads, and protocol converters in automation and smart-grid infrastructure. The crypto block also makes it suitable for payment terminals and embedded security appliances. When designing with this MPU, allocate one PCB layer to the 27 mm BGA breakout fanout, supply 1.0 V core (0.95 V to 1.05 V tolerance) with bulk decoupling near the ball grid, and use impedance-controlled traces for RGMII and DDR. Avoid routing switching nodes beneath the BGA to keep the noise floor on the sensitive analog PLL supply low. This page synthesizes distributor pricing, same-family drop-in alternatives within the PowerQUICC II Pro line, and practical design notes not found in the manufacturer datasheet alone.

Cotação Contato
MPC8313EVRAFFB - PowerQUICC II Pro e300c3 MPU 333MHz | NXP
MPC8313EVRAFFB

MPC8313EVRAFFB - PowerQUICC II Pro e300c3 MPU 333MHz | NXP

The NXP MPC8313EVRAFFB is a PowerQUICC II Pro integrated host processor built on the PowerPC e300c3 core, delivering 333 MHz of 32-bit processing performance in a 516-ball TE-PBGA (27 mm x 27 mm) package with exposed die pad. It is part of NXP's cost-effective, low-power, highly integrated MPC83xx family targeting networking, industrial control, and secure embedded applications. As a microprocessor (MPU), the MPC8313EVRAFFB sits within the broader taxonomy of: MPU -> embedded processor -> system-on-chip class device -> semiconductor. The PowerQUICC II Pro architecture integrates a CPU core, memory controller, communications peripherals, and optional security engine on a single die, eliminating the need for a separate companion chip. This integration reduces BOM cost, board space, and power consumption versus discrete multi-chip implementations for similar workloads. Key differentiating features include hardware-accelerated encryption (the trailing 'E' designation indicates the integrated security engine supporting DES, 3DES, AES, and IPsec), dual 10/100/1000 Mbps Ethernet controllers with built-in MAC, a DDR1/DDR2 memory controller supporting up to 256 MB of addressable memory, PCI Express interface, USB 2.0 high-speed host/device, and a comprehensive set of timers, GPIO, and serial interfaces. The 516-TEPBGA package combines high I/O density with a thermal pad that enables efficient heat removal. Typical applications include SOHO/SMB routers, switches, network-attached storage (NAS), industrial gateways, secure VPN appliances, and print/image processing controllers. The integrated encryption engine makes the 'E' variant particularly well suited to IPsec VPN gateways and SSL/TLS termination in low-to-mid throughput embedded networking equipment. When designing with this MPU, designers must provision a 1.0 V core supply, 1.8 V or 2.5 V DDR2 reference, 3.3 V I/O supply, and a 33.33 MHz system reference clock; a JTAG debug header for boundary-scan and code development is also recommended. The exposed die pad requires a well-designed thermal via array under the package to ensure junction temperature stays within the operating range at full 333 MHz operation. This page synthesizes distributor availability, drop-in alternatives within the same MPC8313E family, application contexts, and practical layout notes not found in a single manufacturer datasheet view.

Cotação Contato
MPC8313EVRAGDB - PowerQUICC II Pro 400MHz MPU | NXP Semiconductors
MPC8313EVRAGDB

MPC8313EVRAGDB - PowerQUICC II Pro 400MHz MPU | NXP Semiconductors

The NXP Semiconductors MPC8313EVRAGDB is a PowerQUICC II Pro microprocessor (MPU) built on the PowerPC e300c3 core, delivering 400 MHz of processing performance in a 516-ball TEPBGA (27x27 mm) package with security/encryption enabled. The MPC8313E integrates a CPU, a DDR memory controller, dual Gigabit Ethernet MACs, PCI Express, and a security engine, providing a complete system-on-chip solution for networking and industrial applications. Key specifications include a 32-bit data bus, 0.09 um process technology, 1.8V/2.5V/3.3V I/O voltage support, 400 MHz core clock, and a 516-TEPBGA exposed-pad package with thermal management via the die-attach paddle. The device also integrates hardware-accelerated IPsec, DES, 3DES, AES, and Kasumi crypto engines for secure communications. An MPU (Microprocessing Unit) is a microprocessor that integrates a CPU core with system-level peripherals such as memory controllers, bus interfaces, and I/O subsystems. The MPC8313E belongs to the PowerQUICC II Pro family: an embedded PowerPC processor family that combines a RISC CPU subsystem with a high-bandwidth communication subsystem. It sits within the hierarchy: microprocessor -> MPU -> networking/communications processor -> embedded system-on-chip. Architecturally, the MPC8313E uses the e300c3 core with separate 32 KB instruction and data caches, a DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs (eTSECs), a USB 2.0 host/device controller, four UARTs, two I2C controllers, dual PCI Express interfaces, and a local bus controller. The integrated security engine accelerates IPsec, AES, DES/3DES, and Kasumi, offloading CPU-intensive crypto workloads from the e300c3 core. Typical applications include industrial routers and gateways, secure VPN concentrators, networked industrial control systems, factory automation controllers, networked storage (NAS) controllers, and security appliances requiring hardware-accelerated encryption. When designing with this MPU, ensure proper decoupling of the 1.8V core, 2.5V DDR reference, and 3.3V I/O rails, and provide adequate thermal relief through PCB thermal vias beneath the exposed die-attach paddle of the 516-TEPBGA package.

Cotação Contato
MPC8313EVRAGDC - PowerQUICC II Pro SoC 400MHz | NXP
MPC8313EVRAGDC

MPC8313EVRAGDC - PowerQUICC II Pro SoC 400MHz | NXP

The NXP MPC8313EVRAGDC is a PowerQUICC II Pro system-on-chip (SoC) integrating a 32-bit e300 core running up to 400 MHz with on-chip DDR1/DDR2 memory controllers, a Gigabit Ethernet MAC, USB 2.0, PCI, and an integrated security engine (SEC). It is supplied in a 516-ball TEBGA (Tape Enhanced Ball Grid Array) package and operates from a 1.0 V core / 2.5 V / 3.3 V I/O supply set, supporting commercial and industrial 0 to 105 C thermal envelopes. A PowerQUICC SoC is a family of integrated communications processors from NXP (formerly Freescale) that combine one or more Power Architecture processor cores with networking and I/O peripherals, deriving from the classic PowerQUICC II Pro product line. The MPC8313E sits in the lower-power, lower-cost tier of that family, optimized for entry-level networking, residential gateways, and industrial control applications where deterministic Ethernet throughput and a small footprint matter more than multi-gigabit switching fabric. Key features include the 32-bit e300c4 processor core, a 32-bit DDR1/DDR2 memory controller with ECC support, dual GMII/TBI/RGMII Gigabit Ethernet interfaces, two USB 2.0 ports (host/device/OTG), a 32-bit/66 MHz PCI controller, an integrated security engine (SEC 3.x) for DES/3DES/AES/SHA/RSA acceleration, and 16 KB I-cache plus 16 KB D-cache. The device supports JTAG debug and COP for in-system emulation, and exposes flexible interrupt routing via the SIU. Architecturally, the MPC8313E uses a 90 nm CMOS process and an internal SoC platform bus with dedicated DMA channels to offload packet processing from the e300 core. The SEC coprocessor executes cryptographic operations independently, freeing the host CPU for control-plane tasks. The result is a highly-integrated single-chip solution that replaces discrete CPU + Ethernet MAC + crypto + memory controller designs. Typical applications include residential gateways and SOHO routers, set-top box and IPTV edge nodes, industrial control and factory automation controllers, networked printers and multifunction devices, and secure access points. The combination of GbE, USB, PCI, and SEC in one package targets cost-sensitive connected-product designs. When designing with this device, use at least four layers with continuous ground/power planes for the BGA breakout, and follow NXP's reference design for DDR2 termination. Verify thermal management because 516-ball BGAs require thermal vias under the die to keep junction below 105 C in enclosed chassis. PCB layout must respect length-matched DDR and GMII/PCI traces per the hardware specification manual. This page synthesizes distributor pricing, drop-in NXP replacements, and practical design notes not found in the NXP datasheet alone, enabling rapid sourcing decisions for the legacy MPC8313E platform.

Cotação Contato
MPC8313EZQAFF - PowerQUICC II Pro MPU, 333MHz, 516-BGA | NXP
MPC8313EZQAFF

MPC8313EZQAFF - PowerQUICC II Pro MPU, 333MHz, 516-BGA | NXP

The NXP (formerly Freescale) MPC8313EZQAFF is a PowerQUICC II Pro integrated host processor featuring a PowerPC e300c3 core running at 333 MHz in a 516-ball TEPBGA (27x27 mm) package. It integrates DDR1/DDR2 memory controller, 16-bit local bus, PCI 2.3, USB 2.0 (host/device), Gigabit Ethernet, and security/encryption acceleration (SEC 2.0) on a single die with a 0.95 V to 1.05 V core voltage. What is an MPU (Microprocessor Unit)? An MPU is a processor IC that integrates CPU cores, memory controllers, and a wide range of I/O peripherals on a single chip for embedded applications. MPUs sit in the system hierarchy: MPU -> microprocessor -> processor IC -> integrated circuit -> semiconductor. Unlike microcontrollers (MCUs) which include on-chip flash and SRAM, MPUs typically require external memory and boot ROM, providing higher performance and scalability for applications such as networking routers, industrial gateways, and networked printers. Key features of the MPC8313E include its e300c3 PowerPC core with 16 KB I-cache and 16 KB D-cache, integrated DDR1/DDR2 SDRAM controller with ECC, two 10/100/1000 Mbps Ethernet MACs, USB 2.0 host and device controllers (with on-chip PHY), PCI 2.3 interface (32-bit, up to 66 MHz), four UARTs, two I2C controllers, and security engine supporting DES, 3DES, AES, RC4, MD5, SHA-1, and public key acceleration. The integrated Security Engine is a key differentiator for IPsec, SSL/TLS, and secure boot applications. The MPC8313E PowerQUICC II Pro processor architecture combines dual issue, out-of-order execution capable, superscalar e300c3 core with a comprehensive set of system peripherals. Its AMBA-style internal bus connects the core to DDR memory controller, local bus controller (LBC), DMA engine, and peripheral bridges. This integration drastically reduces system BOM for cost-sensitive designs while delivering throughput sufficient for entry-level routers and NAS systems. Typical applications include residential gateways, xDSL/cable modems, Wi-Fi access points, networked printers and MFPs, industrial control with security, IP cameras, NAS appliances, and small-office/home-office routers. The on-chip encryption engine makes it especially attractive for IPsec VPN and secure communications applications. When designing with this part, careful PCB layout for 27x27 mm 1.27 mm-pitch BGA is mandatory; use at least 6 layers with dedicated power planes for the 1.0 V core and 3.3 V I/O rails. Boot configuration is selected via reset configuration word driven on the local bus; designers must consider pull-up/pull-down values during PCB bring-up. This page synthesizes distributor pricing, NXP reference design platform documentation, and practical design notes for engineers evaluating the MPC8313E for cost-optimized networking and printing platforms, building on the official NXP datasheet and Freescale hardware specifications documentation.

Cotação Contato
MPC8313EZQAFFB - 333MHz PowerQUICC II Pro MPU, 516-TEPBGA | NXP
MPC8313EZQAFFB

MPC8313EZQAFFB - 333MHz PowerQUICC II Pro MPU, 516-TEPBGA | NXP

The NXP MPC8313EZQAFFB is a PowerPC e300c3 microprocessor from the PowerQUICC II Pro family, integrating a single 32-bit core running up to 333 MHz into a 516-ball TEPBGA (27x27 mm) package. It is designed as a cost-optimized communication processor that combines a high-performance CPU subsystem with on-chip peripherals targeting embedded networking, industrial control, and storage applications. A PowerQUICC II Pro processor is a PowerPC-based system-on-chip designed by NXP (originally Freescale) that integrates one or more e300 cores with a Communications Processor Module (CPM), security engines, DDR memory controllers, and multiple peripheral interfaces. Within the broader taxonomy, the part belongs to the MPC83xx family -> PowerQUICC II Pro -> embedded MPU -> microprocessor -> integrated circuit. The MPC83xx series is widely deployed in routers, switches, WLAN access points, and industrial gateways where deterministic I/O handling and proven PowerPC software ecosystems remain valuable. Key features include a 32-bit e300c3 core with 16 KB instruction and 16 KB data L1 caches, a DDR1/DDR2 memory controller, dual 10/100/1000 Mbps Ethernet MACs, USB 2.0 (full-speed), PCI / PCI-X controller, four UARTs, I2C, SPI, local bus, and a hardware encryption accelerator for DES, 3DES, AES, and SHA-1/MD5. The part supports encryption-accelerated security offload and integrates a security engine, distinguishing it from lower-tier MPC8313E siblings. Industrial temperature range of -40C to +105C (TAFFB suffix) and 1.0 V core supply with 3.3 V I/O make it suitable for thermally constrained embedded designs. Typical applications include SOHO and SMB routers, network attached storage (NAS), industrial control and human-machine interface (HMI) gateways, print and imaging controllers, and secure access equipment. The integrated gigabit Ethernet and security accelerator make it a strong fit for VPN termination points and IPsec/SSL gateways where dedicated crypto offload is required. When designing with this device, ensure proper power sequencing (1.0 V core before 3.3 V I/O), use impedance-controlled DDR2 routing, and provide adequate thermal relief; the 516-TEPBGA package requires a multi-layer PCB with controlled-impedance layers and a sufficient ground plane to maintain signal integrity on the parallel DDR bus. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations not found in the manufacturer datasheet, with sources traceable to DigiKey, Mouser, Octopart, and the Freescale/NXP hardware specifications document.

Cotação Contato
MPC8313EZQAFFC - PowerPC e300c3 MPU, 333MHz, 516-TEPBGA | NXP
MPC8313EZQAFFC

MPC8313EZQAFFC - PowerPC e300c3 MPU, 333MHz, 516-TEPBGA | NXP

The NXP MPC8313EZQAFFC is a PowerPC e300c3 microprocessor IC from the MPC83xx PowerQUICC II Pro family, integrating a single 32-bit core running at 333 MHz in a 516-TEPBGA (27x27 mm) package with exposed pad. The device targets cost-effective, feature-rich networking and digital-home applications with on-chip DDR1/DDR2 memory controllers, PCI, Gigabit Ethernet, USB, and a security engine (SEC). It operates from a 1 V core supply with 3.3 V I/O, suiting typical PowerQUICC embedded board designs. What is a PowerQUICC MPU? A PowerQUICC (pronounced 'power-quick') microprocessor is a family of Power-Architecture system-on-chip (SoC) processors from Freescale/NXP that integrate a PowerPC CPU core with communications peripherals such as Ethernet MACs, PCI, USB, and security accelerators. Within that hierarchy, the MPC8313E belongs to the PowerQUICC II Pro sub-family, which adds DDR2 support and a Gigabit Ethernet interface, sitting between the simpler PowerQUICC I (MPC8xx) and the higher-end PowerQUICC III (MPC85xx). The 'E' suffix indicates hardware-enabled encryption (SEC 2.x), and 'Z' denotes the 516-TEPBGA package option. Key features include a 333 MHz e300c3 core with 16 KB I-cache and 16 KB D-cache, dual DDR1/DDR2 memory controllers up to 333 MHz data rate, integrated Gigabit Ethernet MAC, two 10/100 Ethernet MACs, PCI 2.3 interface, USB 2.0 (Full/Low Speed) and a SEC 2.0 crypto accelerator. The 516-TEPBGA exposed-pad package provides the thermal headroom required for industrial 0 C to 105 C operation. Typical applications include broadband gateways, xDSL Integrated Access Devices, wireless LAN access points, industrial control, and printing/imaging platforms where integrated comms peripherals and Power-Architecture software compatibility reduce BOM and design time. The on-chip SEC engine offloads IPsec and SSL crypto from the CPU. When designing with this MPU, allocate sufficient PCB area for the 27x27 mm BGA and route DDR2 address/command signals with matched impedance and length matching per NXP's hardware design checklist; ensure the exposed pad has a contiguous ground plane for thermal dissipation.

Cotação Contato
MPC8313VRADDB - PowerPC e300c3 MPU 267MHz 516-BGA | NXP
MPC8313VRADDB

MPC8313VRADDB - PowerPC e300c3 MPU 267MHz 516-BGA | NXP

The NXP (formerly Freescale) MPC8313VRADDB is a PowerPC e300c3 based microprocessor IC from the MPC83xx family, featuring a single 32-bit core running at 267MHz, integrated in a 516-pin TEPBGA package measuring 27x27 mm. The device targets cost-sensitive networking and embedded applications with integrated peripherals and a PowerPC instruction set. What is an MPU (Microprocessor Unit)? An MPU is an integrated circuit that contains the central processing unit of a computer system. The MPC83xx family from NXP extends the PowerPC architecture into communications and embedded control, occupying the hierarchy: PowerPC -> RISC processor -> 32-bit MPU -> embedded microprocessor -> semiconductor. PowerPC, originally developed by IBM and Freescale (now NXP), is widely used in routers, storage, and aerospace due to its deterministic performance and mature toolchain. Key features include a single e300c3 core with 32-bit data path, 267MHz core clock, integrated dual Gigabit Ethernet MACs (via the QUICC Engine), DDR1/DDR2 memory controller, PCI Express interface, and a 516-TEPBGA package. The 'VR' designator in the part number denotes a specific speed grade (266-333 MHz) and feature set within the MPC8313 family. The 'ADDB' suffix indicates the temperature grade (typically -40C to +105C extended industrial) and encryption-disabled variant per NXP's ordering scheme. The MPC8313 architecture combines a PowerPC e300c3 core with NXP's QUICC Engine technology, providing hardware-accelerated networking protocol handling. This heterogeneous approach offloads packet processing from the CPU, enabling wire-speed routing and bridging without external co-processors. The device integrates a high-bandwidth DDR memory controller, multiple serial interfaces, USB 2.0, and security engines, allowing designers to build complete networking appliances from a single chip. Typical applications include industrial routers, network attached storage (NAS), DSL/cable modems, smart grid gateways, and embedded industrial control. The integrated QUICC Engine and dual Gigabit Ethernet make it particularly suited for branch-office routers and managed switches requiring wire-speed packet processing. When designing with this device, ensure the 27x27 mm BGA footprint has adequate PCB layer count (typically 8+ layers) and that thermal vias are placed beneath the exposed die area. Power sequencing of the core and I/O voltage rails must follow NXP's reference design; failure to do so can cause latch-up. Programming the QUICC Engine firmware requires NXP's SDK or third-party RTOS support. This page synthesizes distributor availability, drop-in alternatives from the same MPC8313 family, and PCB thermal guidance not found in the standalone datasheet.

Cotação Contato
MPC8313VRAFF - 333MHz PowerPC e300c3 MPU | NXP | Networking
MPC8313VRAFF

MPC8313VRAFF - 333MHz PowerPC e300c3 MPU | NXP | Networking

The NXP MPC8313VRAFF is a PowerPC e300c3 microprocessor in the PowerQUICC family operating at 333MHz, housed in a 516-TEPBGA (27x27 mm) package with exposed thermal pad. This MPC83xx-series device integrates one 32-bit core and is offered in a non-encrypted (non-E) configuration. A PowerQUICC II Pro MPU is a PowerPC-based microprocessor optimized for embedded networking and communications. It belongs to the broader taxonomy: microprocessor (MPU) -> processor -> integrated circuit -> semiconductor. PowerQUICC II Pro derivatives integrate communication peripherals and memory controllers, reducing bill of materials in routers, gateways, and industrial control platforms. Key features of the MPC8313VRAFF include a 333MHz core clock, 32-bit PowerPC e300c3 architecture, integrated DDR memory controller, dual 10/100/1000 Ethernet MACs, USB 2.0 host/device, local bus, PCI express, and security engines. The 516-TEPBGA package provides robust thermal dissipation suitable for industrial networking designs with sustained computational load. The architecture combines a high-performance e300c3 core with the QUICC Engine subsystem, which offloads packet processing tasks from the core. This heterogeneous design allows line-rate handling of common networking protocols while leaving headroom for application-level processing. Typical applications cover industrial routers, secure gateways, network attached storage (NAS), VoIP platforms, and print/imaging controllers. The part targets cost-sensitive embedded networking that still requires deterministic protocol handling. When designing with this device, validate the DDR2 memory topology against the MPC8313 reference manual and ensure thermal management on the exposed pad. Production designs should verify current supply against the latest NXP hardware specifications document, as revisions can affect power sequencing. This page synthesizes distributor inventory, drop-in alternative analysis, and engineering design notes not aggregated in the manufacturer hardware specification document.

Cotação Contato
MPC8313VRAFFB - PowerQUICC II Pro MPU 333MHz | NXP | Networking
MPC8313VRAFFB

MPC8313VRAFFB - PowerQUICC II Pro MPU 333MHz | NXP | Networking

The NXP MPC8313VRAFFB is a PowerPC e300c3-based microprocessor from the PowerQUICC II Pro family, integrating a single 32-bit core running at 333 MHz, a DDR memory controller, and a 516-ball TEPBGA package at 27x27 mm with no security/encryption engine. The VR suffix denotes the 333 MHz core speed grade, AFFB encodes the 516-TEPBGA package and the -40C to +125C extended-temperature screening. Core, system logic and I/O are supplied from separate rails: 1.0 V, 1.8 V, 2.5 V and 3.3 V, all required for proper operation. A microprocessor (MPU) is the central computational unit of an embedded computing system - an integrated circuit that fetches, decodes and executes instructions while coordinating memory, I/O and on-chip peripherals. The MPC8313 sits in the broader taxonomy MPU -> embedded processor -> communications processor -> PowerQUICC II Pro -> NXP/Freescale Power architecture. Unlike a microcontroller (MCU), which integrates flash and modest analog peripherals, the MPC8313 relies on external DDR memory and external boot ROM, giving designers headroom for high-throughput networking, industrial control and storage applications. Key features of the MPC8313VRAFFB include a hardware encryption engine option on the MPC8313E variant (this VRAFFB is the non-EAES version without encryption), two 10/100/1000 Ethernet MACs with integrated PHYs supported through SGMII/RGMII, a USB 2.0 full-/low-speed controller, PCI Express endpoint support on some derivatives, and an enhanced local bus controller for glue-less connection to NAND/NOR flash, FPGAs and ASICs. The integrated DDR1/DDR2 memory controller sustains high-throughput packet flows typical of small office/home office routers, DSLAM line cards and industrial gateways. Architecturally the device pairs the e300c3 PowerPC core with a coherent system bus that fans out to dual Gigabit Ethernet, security acceleration (on E variants), USB and a flexible peripheral set, fabricated in a 0.09 um process. Hardware power management with multiple low-power states, JTAG/COP debugging, and a TEPBGA package that allows efficient multilayer PCB escape make it well suited to long-life industrial designs. Typical uses include industrial networking routers, secure VPN gateways, factory automation controllers, line cards in access equipment, and embedded Linux/u-boot development platforms. The wide I/O supply range (1.8 V / 2.5 V / 3.3 V) eases interfacing to legacy 3.3 V peripherals common in telecom cards. When designing with this part, allocate a contiguous 27x27 mm PCB land pattern and respect the TEPBGA escape rules - microvia or via-in-pad is recommended for inner-row balls. Validate DDR2 IBIS models against the chosen DIMM and keep impedance-controlled differential pairs (SERDES) within the manufacturer's routing guidelines. This page synthesizes distributor pricing, same-package drop-in alternatives (including MPC8313VRAFFB variants and the closely related MPC8313E/MPC8321E family), and practical design notes not collected on any single distributor page.

Cotação Contato
MPC8313VRAGDB - PowerPC e300c3 MPU 400MHz 516-TEPBGA | NXP
MPC8313VRAGDB

MPC8313VRAGDB - PowerPC e300c3 MPU 400MHz 516-TEPBGA | NXP

The NXP MPC8313VRAGDB is a PowerPC e300c3 microprocessor unit (MPU) from the MPC83xx family, featuring a single 32-bit core running at 400MHz in a 516-pin TEPBGA package (27x27 mm). It targets cost-sensitive networking and embedded applications requiring deterministic performance, hardware encryption offload options, and rich peripheral integration. A microprocessor (MPU) is a single-chip processor that integrates the central processing unit, memory management unit, and a wide range of peripheral controllers on a single die, forming the compute heart of an embedded system. Within the broader taxonomy, the MPC8313 belongs to MPU -> 32-bit embedded processor -> application-specific SoC -> semiconductor device category, and it sits at the network-edge/branch-office tier of NXP's PowerQUICC II Pro lineup, optimized for low-power, low-cost gateway designs. Key features of the MPC8313VRAGDB include the e300c3 core with 16KB instruction and 16KB data L1 caches, a 32-bit DDR1/DDR2 memory controller supporting up to 256MB of addressable memory, dual 10/100/1000 Ethernet MACs, dual PCI interfaces, USB 2.0 host/device, and a security engine (SEC 2.3) for hardware-accelerated cryptography on select part numbers. The integrated peripherals reduce external chip count in gateway and WiFi access point designs. The architecture combines a high-performance e300 core with a flexible peripheral set, enabling simultaneous line-rate packet processing and host-side application workloads. DDR1/DDR2 support allows designers to use cost-effective legacy memories, while the dual GbE MACs simplify multi-port networking gear without an external switch. The silicon is fabricated in a 130nm CMOS technology and is designed for fanless operation in industrial environments. Typical applications include SOHO routers, WiFi access points, VoIP gateways, industrial control boards, and print/imaging controllers. It is also found in network-attached storage (NAS) entry-level platforms, set-top box auxiliary processors, and secure terminal equipment requiring the optional security engine. When designing with the MPC8313, allocate the bottom layer of the PCB as a continuous ground pour for thermal dissipation and signal integrity. The TEPBGA package uses lead-free SnAgCu solder balls with 1.27mm pitch; surface-mount assembly requires precise reflow profile control per J-STD-020 moisture sensitivity level handling guidelines. This page synthesizes distributor pricing, parametric context, and cross-reference alternatives that are not consolidated in the manufacturer datasheet, helping engineers verify compatibility and shorten the sourcing cycle.

Cotação Contato
MPC8313VRAGDC - PowerQUICC II Pro MPU 400MHz | NXP
MPC8313VRAGDC

MPC8313VRAGDC - PowerQUICC II Pro MPU 400MHz | NXP

The NXP MPC8313VRAGDC is a PowerQUICC II Pro microprocessor built on the e300c3 core, delivering 400 MHz of 32-bit Power Architecture performance in a 516-pin TEPBGA (27x27 mm) package with exposed pad. It integrates a DDR1/DDR2 memory controller, PCI interface, Gigabit Ethernet (SGMII), high-speed USB 2.0, and a hardware encryption acceleration block, while operating from a multi-rail supply of 1.0 V / 1.8 V / 2.5 V / 3.3 V across a 0 C to 105 C temperature range (Rev 3 silicon). A PowerQUICC II Pro SoC belongs to the broader family of communications processors that combine a general-purpose CPU with integrated peripherals for networking and storage. Within the taxonomy, the device sits at the intersection of microprocessor, system-on-chip (SoC), and communications processor - bridging MPU and ASIC-style integration. It was specifically designed to address demand for higher CPU performance, faster I/O, and lower system cost than earlier PowerQUICC generations, while remaining software-compatible with the e300 family. Key features include a 32-bit 400 MHz e300c3 core with MMU and on-chip L1 caches, a 16/32-bit DDR1/DDR2 memory controller up to 333 MHz, a 32-bit PCI 2.3 bus interface, two Gigabit Ethernet MACs (one via SGMII), a USB 2.0 high-speed controller, four UARTs, two I2C controllers, and an integrated security engine (SEC 2.0) supporting DES, 3DES, AES, and public-key algorithms. The 516-TEPBGA package with exposed pad provides low thermal resistance for fanless embedded designs. Architecturally the MPC8313 combines a superscalar e300 core with the QUICC Engine UCC block for serial protocol termination, allowing wire-speed processing of TDM, Ethernet, and USB traffic without starving the CPU. Compared with switch-based designs, this reduces BOM cost, board area, and power while enabling deterministic throughput for industrial gateways and small-office routers. Typical applications include residential and SMB gateways, DSL/Cable routers, industrial Ethernet switches, networked printers, secure access points, and industrial control nodes. The integrated security engine also makes it well-suited for VPN concentrators and IPsec-aware edge devices that need hardware offload of encryption. When designing with the MPC8313VRAGDC, ensure a minimum 4-layer PCB with a continuous ground plane under the exposed pad. Use 1.0 V VDD_core decoupling at the recommended 33 uF bulk plus 0.1 uF high-frequency caps within 5 mm of every supply pin. Confirm DDR2 trace lengths meet the 25-50 ohm impedance target and that all I/O rails ramp within 50 ms to avoid POR sequencing faults. This page synthesizes distributor pricing, drop-in MPC8313 family variants, and practical PCB/thermal design notes not found in the manufacturer datasheet alone.

Cotação Contato
MPC8313ZQADDB - PowerPC e300c3 MPU 267MHz 516-TEPBGA | NXP
MPC8313ZQADDB

MPC8313ZQADDB - PowerPC e300c3 MPU 267MHz 516-TEPBGA | NXP

The NXP MPC8313ZQADDB is a PowerPC e300c3-based microprocessor IC from the MPC83xx family with a single 32-bit core running at 267 MHz, packaged in a 516-TEPBGA (27x27 mm). This revision 2.1 variant is offered without encryption (W/O ENCR), making it suitable for cost-sensitive networking and embedded applications where crypto accelerators are not required. A microprocessor (MPU) is a single-chip CPU that integrates the central processing unit, cache, memory controller, and frequently peripheral I/O into one device. The PowerPC e300c3 core is a descendant of IBM's Power Architecture, optimized for embedded control and communications; it sits within the broader MPU taxonomy (microprocessor -> processor -> semiconductor -> integrated circuit). MPUs in the MPC83xx family target routers, switches, and wireless base stations where deterministic performance and rich I/O are required. Key features of the MPC8313ZQADDB include a 32-bit PowerPC e300c3 core at 267 MHz, integrated DDR/DDR2 memory controller, dual Gigabit Ethernet MACs, PCI Express interface, USB 2.0, and flexible peripheral support. The 516-TEPBGA package exposes the full I/O set, while the device's power management and low-power modes suit thermally constrained designs. The MPC8313 integrates a system-on-chip architecture combining the CPU, northbridge logic, and peripheral IP. The on-chip unified L2 cache reduces external memory traffic, and the integrated security engine (disabled in this variant) can be left unpopulated in software for lower BOM cost and slightly lower quiescent power. Typical applications include wired and wireless routers, network attached storage (NAS), industrial gateways, and print imaging platforms. The device's gigabit Ethernet and PCI Express make it well-suited for line-rate packet processing at the network edge. When designing with this MPU, ensure the PCB layout provides sufficient thermal copper under the 516-TEPBGA to dissipate 5-8 W typical power, and verify DDR2 signal integrity per the NXP hardware design guide for the MPC8313E. This page synthesizes distributor pricing, drop-in MPC83xx family alternatives, and practical design considerations not found in the manufacturer datasheet, giving engineers a single-source reference for sourcing and selection.

Cotação Contato
MPC8313ZQADDC - PowerQUICC II Pro 266MHz MPU 516-TEPBGA | NXP
MPC8313ZQADDC

MPC8313ZQADDC - PowerQUICC II Pro 266MHz MPU 516-TEPBGA | NXP

The NXP Semiconductors / Freescale MPC8313ZQADDC is a PowerQUICC II Pro communications processor featuring a PowerPC e300c3 core running at up to 267 MHz, packaged in a 516-ball TEPBGA (27x27 mm). It integrates DDR1/DDR2 memory controller, PCI, Gigabit Ethernet, and USB 2.0 interfaces into a single system-on-chip aimed at cost-sensitive embedded networking and industrial control applications. A PowerQUICC (pronounced "power-quick") processor is a family of Power Architecture-based communications SoCs originally developed by Motorola and Freescale (now NXP). Positioned between the higher-end PowerQUICC III MPC85xx and the lower-cost ColdFire families, MPC83xx parts target SOHO routers, wired/wireless gateways, industrial Ethernet switches, and print/image platforms where deterministic I/O and low system cost outweigh peak CPU throughput. Key specifications include a 32-bit PowerPC e300c3 core with 16 KB I-cache and 16 KB D-cache, an integrated 10/100/1000 Mbps Ethernet MAC, USB 2.0 high-speed host/device, two PCI controllers (one 32-bit/66 MHz, one mini-PCI capable), a 32-bit DDR1/DDR2 memory controller up to 266 MHz, and a security engine for AES, DES, and 3DES. Operating voltages of 1.8 V, 2.5 V, and 3.3 V feed core, DDR, and I/O rails respectively, while the industrial temperature grade of 0 to 105 C supports extended thermal envelopes. The MPC8313ZQADDC is fabricated in a 0.09 µm CMOS process for an optimal power/performance balance. Typical applications include SOHO routers, integrated access devices, IP set-top boxes, industrial automation controllers, and point-of-sale terminals. The combination of GbE, PCI, USB, and DDR2 in a single BGA package simplifies board layout compared to multi-chip implementations. When designing with the MPC8313ZQADDC, allocate the largest PCB layers for the DDR2 routing group (matched length within 50 mils) and follow NXP's reference manual for SERDES termination to avoid GbE link-up failures. Verify JTAG/BDM probe placement early to keep debug access available after enclosure integration. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

Cotação Contato
MPC8314CVRADDA - PowerQUICC II Pro SoC, 266MHz e300, 620-HBGA | NXP
MPC8314CVRADDA

MPC8314CVRADDA - PowerQUICC II Pro SoC, 266MHz e300, 620-HBGA | NXP

The NXP MPC8314CVRADDA is a PowerQUICC II Pro integrated communications processor that combines a Power Architecture e300c3 core running at up to 266 MHz with an extensive peripheral set, including DDR1/DDR2 memory controllers, PCI/PCI Express interfaces, Gigabit Ethernet, USB 2.0, and TDM. Packaged in a 620-pin high-density BGA at 29x29 mm, this device targets converged voice, video and data applications. The part is identified as NON-ENCRYPT, meaning security acceleration engines are not enabled in this silicon revision. A PowerQUICC II Pro processor is a system-on-chip (SoC) in the power management and communications processor family. It belongs to the broader category of microprocessors (MPU) and embedded processors, which sit at the top of the system hierarchy: MPU -> embedded processor -> SoC -> communications processor -> PowerQUICC family. These devices integrate a CPU core, memory controller, and multiple high-speed serial interfaces into a single package, enabling designers to build networking, industrial, and consumer gateway products without an external chipset. Key features include the e300c3 core with 32-bit Power Architecture ISA, dual DDR1/DDR2 memory controllers with ECC support, a 32-bit PCI controller plus a single-lane PCI Express endpoint/root-complex interface, dual 10/100/1000 Ethernet MACs with integrated PHY interfaces, USB 2.0 high-speed host/device, and a multi-channel TDM interface for legacy telecom and HDLC. On-chip peripherals also include I2C, SPI, UART, local bus, and NAND/NOR flash controllers, reducing external component count. Typical applications include digital home gateways, SOHO routers, IP set-top boxes, industrial control and factory automation controllers, networked printers, and security/surveillance DVRs. The combination of Gigabit Ethernet, PCI Express, and TDM specifically targets hybrid IP/PSTN gateways where legacy time-division-multiplexed links must coexist with packet-based traffic. Designers should note that BGA-620 packages require controlled-assembly processes (X-ray inspection, multi-layer PCB stack-up) and thermal management based on the 105 °C industrial temperature window. The device is migration-compatible with the MPC8314E variant when encryption (SEC) engines are required, since both share the same die and pinout.

Cotação Contato