Microcontroladores

Produtos (18688)

ATSAM3S1CA-AU - 64MHz ARM Cortex-M3 MCU, 64KB Flash | Microchip
ATSAM3S1CA-AU

ATSAM3S1CA-AU - 64MHz ARM Cortex-M3 MCU, 64KB Flash | Microchip

The Microchip Technology ATSAM3S1CA-AU is a 32-bit ARM Cortex-M3 flash microcontroller in the SAM3S series, running at up to 64 MHz with 64 KB of embedded flash program memory and 16 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest tier of the embedded computing hierarchy (MCU -> embedded processor -> SoC -> application processor). The SAM3S family is based on the ARM Cortex-M3 RISC processor architecture, a widely adopted 32-bit core optimized for deterministic, low-power embedded control. Originally introduced by Atmel Corporation and now manufactured by Microchip Technology after its 2017 acquisition of Atmel, the SAM3S line targets cost-sensitive industrial and consumer designs. Key features include the 64 MHz Cortex-M3 core with nested vectored interrupt controller, 64 KB flash memory with in-system programming capability, and a rich peripheral set spanning EBI/EMI external bus interfaces, I2C (TWI), SPI, SSC (synchronous serial controller), UART/USART, USB 2.0 full-speed device, and memory card interfaces. The device provides 47 general-purpose I/O lines and operates from a 1.8V/3.3V supply domain, with the core supply specified at 1.08V to 1.32V according to distributor datasheet summaries. Industrial temperature grade options support demanding environments. Architecturally, the Cortex-M3 core uses a Harvard bus structure with a three-stage pipeline and Thumb-2 instruction set, delivering efficient code density and interrupt latency. The flash accelerator prefetches instructions to keep the 64 MHz core fed from single-cycle-access flash, while the multi-layer bus matrix allows peripheral DMA transfers without CPU intervention. Typical applications include industrial automation and control panels, USB-connected embedded devices and data loggers, and consumer appliance interfaces, where a balanced mix of serial connectivity, moderate compute performance, and flash expandability across the SAM3S family is required. A key design consideration is supply-domain management: the core runs from an on-chip regulator fed by the 3.3V I/O supply, so decoupling and sequencing must follow the manufacturer datasheet recommendations, and pin compatibility across SAM3S flash-size variants should be verified against the pin configuration section before PCB reuse. This page synthesizes distributor inventory data, datasheet summaries, and family drop-in alternatives not consolidated in any single manufacturer document.

Cotação Em estoque
ATSAM3S1CA-AUR - 32-bit Cortex-M3 MCU 64MHz 64KB Flash | Microchip
ATSAM3S1CA-AUR

ATSAM3S1CA-AUR - 32-bit Cortex-M3 MCU 64MHz 64KB Flash | Microchip

The Microchip Technology ATSAM3S1CA-AUR is a 32-bit ARM Cortex-M3 flash microcontroller operating at 64 MHz, with 64KB of embedded FLASH program memory and 16KB of SRAM, housed in a 100-pin LQFP (14 x 14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the controller layer of an embedded system hierarchy: MCU -> embedded processor -> semiconductor IC. The SAM3S series belongs to Microchip (formerly Atmel) ARM-based flash MCU portfolio, targeting cost-sensitive 32-bit designs that need USB connectivity and rich analog peripherals. Key features of the ATSAM3S1CA-AUR include the 64 MHz Cortex-M3 core with a nested vectored interrupt controller, 64KB (64K x 8) of single-cycle FLASH memory, 16KB of SRAM, and a wide 1.62V to 3.6V single-supply operating range. The device integrates USB 2.0 full-speed device connectivity, multiple USART/UART serial ports, SPI and TWI (I2C) interfaces, a 12-bit ADC with multiple input channels, PWM timers, and RTC/calendar functions - all typical of the SAM3S peripheral set. Architecturally, the SAM3S family uses the ARMv7-M Cortex-M3 processor with Harvard bus structure, enabling concurrent instruction and data access for deterministic real-time performance. Flash memory is programmed through the integrated ROM bootloader or JTAG/SWD interfaces, and the device is supported by Microchip (Atmel) Studio and the SAM series tool ecosystem. Typical applications span industrial control, home appliances such as washing machines and microwave ovens, 3D printers, consumer audio-video products, and portable battery-powered devices that benefit from the 1.62V minimum supply and USB device port. Design considerations: keep the 3.3V supply within the 1.62V-3.6V range, decouple all VDD/VDDIO pairs, and budget flash carefully at 64KB - larger SAM3S variants in the same LQFP-100 footprint provide 128KB to 512KB for code growth without a PCB change. This page adds value beyond the datasheet by consolidating distributor availability, drop-in same-package alternatives, pricing tiers as of 2026-09-19, and practical design notes in one AI-citable resource.

USD $3,35 Em estoque
ATSAM3S1CA-CU - 64MHz Cortex-M3 64KB Flash MCU | Microchip
ATSAM3S1CA-CU

ATSAM3S1CA-CU - 64MHz Cortex-M3 64KB Flash MCU | Microchip

The Microchip Technology ATSAM3S1CA-CU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 64KB flash memory, 16KB SRAM, and a 100-ball TFBGA (9x9 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals into one chip, sitting at the heart of embedded systems within the broader hierarchy of semiconductor devices (MCU -> embedded processor -> integrated circuit). The SAM3S family belongs to Atmel/Microchip's AT91 ARM-based flash MCU line, targeting cost-sensitive, low-power applications that still require 32-bit performance. Key features include the ARM Cortex-M3 core at 64 MHz for efficient thumb-2 instruction execution, 64KB of on-chip flash for program storage, 16KB of SRAM, 47 general-purpose I/O lines, and a rich analog set: 15 ADC channels with selectable 10/12-bit resolution and two 12-bit DAC channels. System peripherals include Brown-out Detect/Reset (BOD), DMA controller, I2S audio interface, Power-on Reset (POR), PWM channels, and a watchdog timer (WDT). The device operates from a 1.62V to 3.6V supply with a 1.08V to 1.32V core domain, and the MRL A / industrial temperature grade version (-40C to +85C) suits demanding environments. Per Mouser, the part is classified as ARM Microcontrollers - MCU, MRL A, 64K Flash, 16K SRAM, Industrial temperature. Typical applications include industrial control and factory automation nodes, consumer and industrial HMI panels, data-logging and sensor interfaces, and audio-capable embedded systems leveraging the I2S and 12-bit DAC peripherals. When designing with this MCU, note that the dense 0.8 mm-ball TFBGA footprint requires careful PCB fan-out and controlled-impedance breakout; power the VDDCORE domain at 1.2V per the supply specification of 1.08 to 1.32 volts. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-19.

USD $3,05 Em estoque
ATSAM3S1CB-AU - ARM Cortex-M3 64MHz 64KB Flash MCU | Microchip
ATSAM3S1CB-AU

ATSAM3S1CB-AU - ARM Cortex-M3 64MHz 64KB Flash MCU | Microchip

The Microchip Technology (Atmel) ATSAM3S1CB-AU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz with 64 KB embedded Flash and 16 KB SRAM, housed in a 100-pin LQFP (14 x 14 mm) surface-mount package. It operates from 1.62 V to 3.6 V and is pin-to-pin compatible with the SAM3N1C family. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy (MCU -> embedded processor -> system-on-chip -> semiconductor device). The SAM3S family sits within Microchip's ARM-based 32-bit MCU portfolio, positioned for cost-sensitive applications that still require the 32-bit performance and Thumb-2 instruction efficiency of the ARM Cortex-M3 architecture, revision 2.0. Key differentiating features include the Cortex-M3 Memory Protection Unit (MPU), a 128-bit-wide Flash access path feeding a memory accelerator that sustains near-zero-wait-state execution at 64 MHz, and a rich peripheral set including USB 2.0 Full-Speed Device port, USARTs, SPI, TWI (I2C), PWM channels, a 12-bit ADC, and a DMA controller that offloads data transfers from the CPU. These peripherals reduce external component count in human-interface and connectivity designs. Technically, the device integrates 16 KB of ROM for bootloader or code storage, a Power Management Controller (PMC) with multiple low-power modes, a Real-Time Timer, Watchdog, and an 8-channel DMA. Wide operating voltage tolerance (1.62 V to 3.6 V) allows direct battery operation in portable products. The industrial temperature variant (-40 C to +85 C) suits harsh environments. Typical applications include industrial control panels, building automation nodes, consumer appliances with touch or LCD interfaces, USB-connected instruments, battery-powered metering, and motor control sub-systems, where 64 KB of Flash and DMA-driven peripherals provide an efficient single-chip solution. A key design consideration is Flash density headroom: at 64 KB, the S1CB is the entry point of the SAM3S family, so pinning out the 100-pin footprint while choosing this smallest-memory variant is wise only if code size projections are comfortably below capacity; the pin-compatible S1CA/S4BA variants allow later upgrades without PCB rework. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.

USD $3,10 Em estoque
ATSAM3S1CB-AUR - 64MHz Cortex-M3 MCU, 64KB Flash | Microchip
ATSAM3S1CB-AUR

ATSAM3S1CB-AUR - 64MHz Cortex-M3 MCU, 64KB Flash | Microchip

The Microchip Technology ATSAM3S1CB-AUR is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz with 64 KB of embedded flash memory and 16 KB of SRAM, supplied in a 100-pin LQFP (14x14 mm) surface-mount package. It operates from a 1.62V to 3.6V single supply and is rated for the industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters. Within the embedded systems hierarchy, the SAM3S family sits in the 32-bit ARM-based microcontroller class, positioned above 8-bit MCUs like the PIC16 and ATmega families and below high-performance Cortex-M7 parts such as the SAMV71. Key features of the ATSAM3S1CB-AUR include the energy-efficient ARM Cortex-M3 RISC core with its three-stage pipeline and Thumb-2 instruction set, 64 KB of single-cycle flash for program storage, 16 KB of SRAM for data and stacks, and a rich peripheral set typical of the SAM3S series, including USB device support, USARTs, SPI, TWI (I2C), and a multi-channel ADC that suits sensor acquisition and human-interface designs. Architecturally, the Cortex-M3 core executes deterministic, low-latency interrupt handling through its Nested Vectored Interrupt Controller (NVIC), making the part well suited to real-time embedded control. The flash accelerator keeps the core fed at 64 MHz without wait-state penalties in typical code paths, while the SAM3S power architecture supports multiple low-power modes for battery-conscious designs. Typical applications include industrial automation and control nodes, consumer appliance interfaces, metering and sensor-integration products, and USB-connected handheld equipment where 64 KB of code space and 64 MHz throughput are sufficient. When designing with this device, plan decoupling capacitors close to each supply pin pair, budget the 64 KB flash carefully against bootloader and library overhead, and confirm industrial temperature requirements against the suffix code before layout freeze. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing comparative value beyond a standard catalog listing.

USD $4,05 Em estoque
ATSAM3S1CB-CU - 64MHz Cortex-M3 64KB MCU | Microchip
ATSAM3S1CB-CU

ATSAM3S1CB-CU - 64MHz Cortex-M3 64KB MCU | Microchip

The Microchip Technology ATSAM3S1CB-CU is a 32-bit ARM Cortex-M3 flash microcontroller operating at up to 64 MHz, with 64 KB (64K x 8) flash memory, 16 KB SRAM, and a 1.8V core supply, housed in a 100-ball TFBGA (9x9 mm) package for surface-mount assembly. A microcontroller (MCU) is an integrated circuit that combines a processor core, memory, and peripherals on a single die, forming the lowest layer of the embedded processing hierarchy (MCU -> embedded processor -> integrated circuit -> semiconductor). The SAM3S series belongs to the ARM Cortex-M3 class of 32-bit RISC microcontrollers, which occupy the mid-range performance tier between small 8-bit MCUs and high-performance Cortex-M7 applications processors. Key features of the ATSAM3S1CB-CU include the 64 MHz Cortex-M3 RISC core with Thumb-2 instruction set, 64 KB of embedded flash for code storage, 16 KB of SRAM for data and stack, and industrial temperature grade operation for harsh-environment deployment. The 100-terminal fine-pitch ball grid array (TFBGA, square 9x9 mm) provides high I/O density in a compact footprint, suitable for space-constrained boards. Architecturally, the device is part of the SAM3S family originally developed by Atmel (now Microchip Technology after the 2016 acquisition), sharing a common peripheral set with SAM3S1C, SAM3S4C, and SAM3S8C variants. Family members are software-compatible, so code written for the 64 KB flash grade migrates directly to higher-memory grades in the same package. Typical applications include industrial automation nodes, sensor data acquisition, consumer appliance control, and portable instrumentation where 32-bit processing at low power is required. When designing with this part, verify flash density headroom (64 KB is the smallest C-package grade) and confirm the TFBGA land pattern matches your PCB fabrication capability, as 0.8 mm ball pitch requires standard HDI-class assembly. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in alternatives, and engineering design notes in one citable reference.

USD $2,82 Em estoque
ATSAM3S1CB-CUR - 64MHz Cortex-M3 MCU 64KB Flash | Microchip
ATSAM3S1CB-CUR

ATSAM3S1CB-CUR - 64MHz Cortex-M3 MCU 64KB Flash | Microchip

The Microchip Technology ATSAM3S1CB-CUR is a 32-bit ARM Cortex-M3 flash microcontroller running at 64 MHz with 64 KB of Flash program memory and 16 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest tier of the embedded processing hierarchy (MCU -> embedded processor -> system-on-chip). The SAM3S family belongs to Microchip (formerly Atmel) ARM-based flash MCU portfolio, positioning it as a mid-range 32-bit solution between small 8-bit MCUs and application processors. Key features include the ARM Cortex-M3 core with a 3-stage pipeline and Harvard architecture, operation from a single 1.62V to 3.6V supply, and integrated analog peripherals including a 12-bit ADC (the family also offers 10-bit and 12-bit converter options per LCSC data). The -CUR suffix denotes the industrial temperature range in the lead-free TFBGA ball-grid-array package suitable for compact, high-density boards. From an architecture standpoint, the Cortex-M3 core delivers deterministic interrupt handling via the Nested Vectored Interrupt Controller and Thumb-2 instruction efficiency. A DMA controller offloads data transfers from the CPU, according to the Microchip SAM3S1C product page, improving real-time throughput for peripheral-heavy designs. Flash memory allows in-system reprogramming, and the wide 1.62V-3.6V supply range supports battery-powered operation. Typical applications include industrial control and automation nodes, consumer devices, and portable battery-powered instruments where 64 KB of code space and a dense 9x9 mm BGA footprint are sufficient. The 100-terminal TFBGA saves board area versus QFP alternatives. Design consideration: verify the flash density matches your code size headroom; the pin-compatible SAM3S2C and SAM3S4C family members double and quadruple flash if 64 KB proves tight. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Prices as of 2026-09-19.

USD $1,74 Em estoque
ATSAM3S2AA-AUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2AA-AUR

ATSAM3S2AA-AUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2AA-AUR is a 32-bit ARM Cortex-M3 flash microcontroller operating at up to 64 MHz, with 128 KB of embedded flash memory and 32 KB of SRAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package rated for industrial temperatures. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, sitting at the heart of embedded systems. Within the hierarchy of semiconductors, this device belongs to the flash microcontroller family, derived from the broader ARM Cortex-M processor architecture and Microchip's (formerly Atmel) SAM product line of 32-bit MCUs. Key features of the ATSAM3S2AA-AUR include the Thumb-2 instruction set for high code density, a rich peripheral set with multiple UARTs, SPI, I2C (TWI), I2S, and USB 2.0 Full-Speed connectivity, and DMA controllers that offload data movement from the CPU. The parallel data capture mode on the PIOs allows data collection from devices not compliant with standard memory read protocols, such as low-cost image sensors, with DMA transferring data to memory automatically. The device operates from a single 1.62V to 3.6V supply and is built on CMOS technology, balancing performance with power efficiency. According to Microchip, the SAM3S2A is pin-to-pin compatible with the SAM3N2A, giving designers a straightforward migration path between the SAM3N and SAM3S series when USB or additional analog peripherals are required. Typical applications include industrial control and automation nodes, consumer appliances with USB interfaces, battery-powered metering devices, and PC peripherals such as mice and keyboards where USB Full-Speed and low power are key requirements. The 64 MHz Cortex-M3 core provides ample headroom for control loops and communication stacks. When designing with this MCU, use the industrial temperature grade (-40C to +85C) margin carefully in sealed enclosures, and allocate the 128 KB flash budget with bootloader and firmware update overhead in mind. The Tape & Reel packaging (suffix AUR) supports automated pick-and-place assembly. This page synthesizes distributor inventory data, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

USD $2,66 Em estoque
ATSAM3S2AA-MU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2AA-MU

ATSAM3S2AA-MU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2AA-MU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 128 KB of embedded flash and 32 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package with exposed pad. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded systems hierarchy: microcontroller -> embedded processor -> system-on-chip. The SAM3S series belongs to Atmel (now Microchip) ARM-based flash MCU family and sits above 8-bit AVR and PIC16 parts in performance while retaining low power operation. Key features include the ARM Cortex-M3 revision 2.0 core with Memory Protection Unit (MPU) and Thumb-2 instruction set, a 128-bit-wide flash accelerator for zero-wait-state execution at full speed, USB 2.0 Full-Speed device port, and a rich peripheral set including a 12-bit ADC, 2-channel 16-bit PWM, USARTs, and a parallel capture mode on the PIOs for low-cost image sensors. The device operates from a 1.62V to 3.6V supply (1.8V/3.3V nominal rails), making it compatible with both Li-ion battery and standard 3.3V industrial power domains. DMA is available on all major peripherals, offloading data movement from the CPU and reducing active current consumption. The part is pin-to-pin compatible with the AT91SAM7S legacy family and the SAM3N series, enabling straightforward platform upgrades. Typical applications include industrial sensors and HMI panels, consumer appliances, battery-powered portable instruments, and USB-connected data acquisition devices where 64 MHz performance and USB connectivity are required without the cost of larger MCUs. Design consideration: minimize power by using the Flash Living Region and Sleep/Wait/BackUp modes; use wait-state-free code placement carefully as performance depends on the flash accelerator behavior. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3,60 Em estoque
ATSAM3S2AA-MUR - Cortex-M3 MCU 64MHz 128KB Flash | Microchip
ATSAM3S2AA-MUR

ATSAM3S2AA-MUR - Cortex-M3 MCU 64MHz 128KB Flash | Microchip

The Microchip Technology ATSAM3S2AA-MUR is a 32-bit ARM Cortex-M3 microcontroller from the SAM3S series, running at 64 MHz with 128KB (128K x 8) of embedded Flash memory, housed in a 48-pin VFQFN (7x7 mm) exposed-pad package and operating from a 1.62V to 3.6V supply. A microcontroller (MCU) is a single-chip embedded processor that integrates a CPU core, program memory, data memory, and peripherals such as timers, serial interfaces, and analog functions. Within the embedded systems hierarchy, the SAM3S sits in the medium-range general-purpose class of 32-bit MCUs, positioned above 8-bit devices like the PIC16 family and below high-performance Cortex-M4/M7 parts. The ARM Cortex-M3 architecture provides deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC) and efficient Thumb-2 instruction execution. Key features include 64 MHz core performance, 128KB of on-chip Flash for program storage, low-power operation across the industrial temperature range, and a peripheral set that Microchip describes as offering the best ratio of reduced power consumption, processing power, and peripherals in its class. The PIOs support a parallel data capture mode that collects data from non-standard sources such as low-cost image sensors, with DMA transfers offloading the CPU. The device integrates a Cortex-M3 core with configurable Flash and SRAM organization, and Microchip notes Flash is architected in dual banks on SAM3S family members, supporting ECC and flash-banking techniques. The exposed-pad QFN package provides low inductance power delivery and good thermal performance for compact industrial designs. Typical applications include industrial control panels, consumer appliances, metering systems, and sensor-hub designs that benefit from the parallel capture interface and DMA-driven data flow. When designing, ensure the 1.62V to 3.6V supply range is respected and decouple the VDDCORE and VDDIO domains per the manufacturer datasheet; the M suffix denotes tape-and-reel packaging for automated assembly. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $3,49 Em estoque
ATSAM3S2BA-AU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2BA-AU

ATSAM3S2BA-AU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2BA-AU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz with 128 KB embedded Flash and 32 KB SRAM, housed in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy above discrete logic and below application processors and systems-on-chip. The SAM3S family belongs to Microchip's SMART ARM-based MCU portfolio, targeting cost-sensitive 32-bit industrial and consumer designs. Key features of the ATSAM3S2BA-AU include the ARM Cortex-M3 revision 2.0 core with Thumb-2 instruction set and Memory Protection Unit (MPU), a 128-bit-wide Flash memory interface with an accelerator for efficient 64 MHz execution, and pin-to-pin compatibility with the earlier AT91SAM7S series in 48- and 64-pin versions, which simplifies migration of legacy designs. Technical depth: the device integrates typical SAM3S peripherals such as USARTs, SPI, TWI (I2C), PWM channels, an ADC, USB 2.0 full-speed device port, and a flexible clock tree with fast RC oscillators and crystal inputs. The suffix 'AU' identifies the 64-pin LQFP, industrial temperature range, and lead-free tray packaging, making the part suited to standard reflow assembly. Typical applications include industrial control panels, battery-charged portable instruments, consumer appliances, motor-control front ends, and USB-connected sensor interfaces, where 128 KB of Flash and rich connectivity cover mid-complexity firmware without external memory. Design consideration: verify supply-voltage decoupling on VDDCORE and VDDIO domains and confirm Flash capacity against growth headroom, since larger SAM3S variants such as the ATSAM3S4BA share the same footprint for upward migration. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet.

USD $4,66 Em estoque
ATSAM3S2BA-AUR - Cortex-M3 MCU 64MHz 128KB Flash | Microchip
ATSAM3S2BA-AUR

ATSAM3S2BA-AUR - Cortex-M3 MCU 64MHz 128KB Flash | Microchip

The Microchip Technology ATSAM3S2BA-AUR is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 128 KB of flash memory, 32 KB of SRAM, and a wide 1.62V to 3.6V operating supply, housed in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, non-volatile program memory, volatile data memory, and a rich set of peripherals on one die. Within the semiconductor hierarchy, the ATSAM3S2BA-AUR belongs to the Microchip (formerly Atmel) SAM3S family of ARM Cortex-M3 microcontrollers, which sit above simpler 8-bit MCUs in processing capability while retaining low-power operation for embedded control systems. Key features include the 64 MHz Cortex-M3 core with a 3-stage pipeline and Thumb-2 instruction set, 128 KB of on-chip flash for code storage, fast SRAM, and an extended industrial temperature rating. The peripheral set typical of the SAM3S series includes UART/USART serial ports, SPI, TWI (I2C), an ADC, PWM channels, and USB connectivity, enabling single-chip designs for communication-heavy applications. The device operates from a single 1.62V to 3.6V rail, supporting battery-powered designs. Architecturally, the ARM Cortex-M3 core integrates a Nested Vectored Interrupt Controller (NVIC) for deterministic low-latency interrupt handling and hardware divide support. Flash-based program memory with in-system programming allows firmware field updates, while the 10x10 mm LQFP-64 package provides sufficient I/O count for display, sensor, and actuator interfaces. Typical applications include industrial control and automation nodes, consumer appliances, battery-powered portable instruments, and USB-enabled embedded devices where a 32-bit core with ample flash is required without the cost of higher-memory parts. A key design consideration is supply decoupling: place low-ESR ceramic capacitors close to each VDD/VDDIO pin pair, and confirm 1.8V/3.3V domain separation per the SAM3S datasheet electrical characteristics before PCB routing. This page synthesizes distributor pricing, drop-in same-family alternatives, cross-reference candidates, and practical design notes not consolidated in the manufacturer datasheet.

USD $4,10 Em estoque
ATSAM3S2BA-MUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2BA-MUR

ATSAM3S2BA-MUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2BA-MUR is a 32-bit ARM Cortex-M3 microcontroller from the SAM3S family, running at up to 64 MHz with 128 KB of embedded Flash and 32 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A microcontroller (MCU) is a single-chip integrated circuit that combines a processor core, program memory, data memory, and a rich set of peripherals into one package. Within the embedded-systems hierarchy, the SAM3S sits in the mid-range 32-bit MCU class, positioned above 8-bit PIC and AVR devices and below high-performance Cortex-M4/M7 families, targeting cost-sensitive applications that still require 32-bit compute throughput and USB connectivity. Key features include the 64 MHz Cortex-M3 core with a 3-stage pipeline and Thumb-2 instruction set, 128 KB of self-programmable Flash with a dedicated flash controller, and an integrated USB 2.0 Full-Speed Device port. The device also integrates a 12-bit ADC with 16 channels, a 2-channel 12-bit DAC, a capacitive-touch support peripheral, PWM channels, USART/SPI/TWI serial interfaces, and an internal 1.8V/3.3V operating regime supplied from 1.62V to 3.6V. Technically, the SAM3S implements Microchip (Atmel) SMART ARM-based architecture with a multi-layer bus matrix, DMA-capable peripheral event system, and power management controller offering sleep, wait, and backup modes with low quiescent consumption for battery-powered designs. The exposed-pad QFN package improves thermal dissipation and ground return paths for mixed-signal performance. Typical applications include industrial control panels, consumer appliances, USB-connected sensors and dataloggers, and battery-powered metering products where the combination of Cortex-M3 performance, USB device connectivity, and integrated analog reduces total bill-of-materials cost. For design, plan the VDDCORE/VDDIO decoupling network per the manufacturer datasheet and use the exposed pad as the main ground connection; flash wait-state configuration relative to the 64 MHz clock also affects efficiency. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $4,10 Em estoque
ATSAM3S2CA-AU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2CA-AU

ATSAM3S2CA-AU - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2CA-AU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 128 KB of embedded Flash memory and 32 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. Formerly an Atmel AT91 SAM3S series device, it integrates an MPU, a Thumb-2 instruction set pipeline, and a rich peripheral set for embedded control. A 32-bit microcontroller (MCU) is an integrated circuit that executes application code and controls peripherals on a single chip; the Cortex-M3 core sits within the ARM MCU hierarchy beneath higher-performance Cortex-M4/M7 parts and above 8-bit architectures. The SAM3S family targets cost-sensitive, low-power embedded systems that still need 32-bit processing headroom. Key features include the ARM Cortex-M3 revision 2.0 core at 64 MHz with Memory Protection Unit (MPU), 128 KB single-cycle Flash and 32 KB SRAM, 47 general-purpose I/O lines on this 100-pin variant, and Flash-based program storage with in-system programming. The MRL/industrial temperature grade supports -40C to +85C operation per distributor data. The architecture combines the three-stage Harvard Cortex-M3 pipeline with an on-chip bus matrix, allowing Flash execution while peripherals such as UARTs, timers, and USB operate concurrently. Nested Vectored Interrupt Controller (NVIC) latency is deterministic, which suits real-time embedded automation and metering firmware. Core supply operates in the 1.08 V to 1.32 V domain with an integrated regulator from a 1.8 V/3.3 V IO supply. Typical applications include industrial control, IoT sensor nodes, motor control, metering, and low-power board designs, where the SAM3S balances cost, power, and processing throughput. Pin-to-pin compatibility with AT91SAM7S legacy parts (48- and 64-pin versions per datasheet notes) eases migration. When designing with this device, budget Flash carefully: 128 KB is adequate for most control firmware but tight for stacks with USB host plus file systems; consider ATSAM3S4CA (256 KB) if code size may grow. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,25 Em estoque
ATSAM3S2CA-AUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2CA-AUR

ATSAM3S2CA-AUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2CA-AUR is a 32-bit ARM Cortex-M3 microcontroller of the SAM3S series, running at up to 64 MHz with 128 KB of flash memory and a 100-pin LQFP (14x14 mm) surface-mount package. It operates from a 1.62V to 3.6V supply (1.8V/3.3V typical rails). A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory (flash), data memory (SRAM), and a rich set of peripherals such as timers, serial interfaces (USART, SPI, I2C/TWI), ADC channels, and general-purpose I/O. Within the semiconductor hierarchy, the ATSAM3S2CA-AUR belongs to the SAM3S family, the ARM Cortex-M3 core class, the 32-bit microcontroller category, and the broader embedded processor / power management system domain of a board design. Key differentiating features include the Thumb-2 instruction set of the Cortex-M3 core, which delivers high code density; 128 KB (128K x 8) of on-chip flash for program storage; fast SRAM for data; and a comprehensive peripheral set that allows a single MCU to handle sensing, control, and communication tasks simultaneously. Industrial temperature qualification and a green, RoHS-compliant LQFP package make the part suitable for long-lifecycle embedded products. Architecturally, the Cortex-M3 core uses a Harvard bus structure with separate instruction and data paths, a nested vectored interrupt controller (NVIC) for deterministic interrupt latency, and hardware multiply/divide support. The SAM3S series pairs this core with Microchip (formerly Atmel) peripheral infrastructure, including DMA-capable serial controllers that offload the CPU during data transfers. Typical applications include industrial control and automation nodes, consumer and medical devices, test instruments, and smart sensing modules. The 100-pin LQFP offers abundant GPIO for keypad, display, and peripheral interfacing, which is why this variant is popular for human-machine interface boards. When designing with this MCU, verify the flash density matches your firmware footprint before committing a footprint - larger SAM3S family members (ATSAM3S4CA, ATSAM3S8CA) are pin-compatible upgrades that require no PCB changes. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes beyond what the manufacturer datasheet provides, giving engineers a single citable reference for the ATSAM3S2CA-AUR.

Cotação Em estoque
ATSAM3S2CA-CU - 64MHz ARM Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2CA-CU

ATSAM3S2CA-CU - 64MHz ARM Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2CA-CU (formerly Atmel) is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 128 KB of flash memory and 32 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy above discrete logic and below application processors. The SAM3S family belongs to the ARM Cortex-M3 class of 32-bit MCUs, widely used where deterministic performance, low power, and rich analog/digital peripherals are required at moderate cost. Key features include the ARM Cortex-M3 core with Thumb-2 instruction set and nested vectored interrupt controller (NVIC), 1.62V to 3.6V single-supply operation, a USB 2.0 full-speed device port, multiple USART/SPI/TWI serial interfaces, a 12-bit ADC, and an internal RC oscillator option set (4/8/12 MHz plus 32 kHz) that can remove the need for an external crystal in cost-sensitive designs. Architecturally, the device integrates a multi-layer bus matrix and peripheral DMA channels, allowing peripherals such as the ADC and USARTs to transfer data without CPU intervention. The flash accelerator keeps effective execution close to the 64 MHz core speed, while power management controllers with multiple sleep and wait modes support battery-operated designs. Typical applications include industrial control panels, consumer appliances, data-logging and sensor-gateway products, and USB-connected portable equipment where the full-speed USB device controller and generous USART count (up to 7 UART-class ports) simplify connectivity. Design consideration: the TFBGA (9x9) ball-grid package demands controlled-impedance multilayer PCB layout and reflow assembly; teams requiring hand soldering or simpler inspection should evaluate the pin-compatible LQFP counterpart within the SAM3S family before committing to the BGA footprint. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in same-package alternatives across the SAM3S flash-density ladder, and practical design notes for BGA layout and power-supply decoupling.

USD $3,60 Em estoque
ATSAM3S2CA-CUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip
ATSAM3S2CA-CUR

ATSAM3S2CA-CUR - 64MHz Cortex-M3 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM3S2CA-CUR is a 32-bit ARM Cortex-M3 microcontroller with 128KB FLASH program memory, 32KB SRAM, and a 64MHz core, housed in a 100-ball TFBGA (9x9 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die, sitting at the center of the embedded-system hierarchy: MCU -> embedded processor -> semiconductor device. The SAM3S family from Microchip (originally Atmel) belongs to the 32-bit ARM Cortex-M class of flash microcontrollers, which are widely used where deterministic, energy-efficient control is required. Key features include a 1.62V to 3.6V supply range supporting both 1.8V and 3.3V rails, operation from -40C to +85C for industrial environments, and a rich peripheral set: 12-bit ADC, 12-bit DAC, UART, USART, TWI (I2C), SPI, SSC, I2S, HSMCI, IrDA, and USB Device. The 79 programmable I/O lines give designers substantial expansion flexibility in a compact 9x9 mm ball grid array. Technically, the Cortex-M3 core implements the ARMv7-M architecture with a 3-stage pipeline and Thumb-2 instruction set, delivering approximately 1.25 DMIPS/MHz. Flash acceleration logic allows full-speed 64MHz execution from embedded flash without wait-state penalties for most code. CMOS process technology keeps active power low, while the SAM3S power-management controller offers multiple sleep and wait modes for battery-conscious designs. Typical applications include consumer and industrial devices with TFT LCD or segmented displays, battery-powered portable instruments, USB-connected data loggers, and motor or sensor control nodes. The generous peripheral mix makes the SAM3S2 a single-chip solution that avoids external bridge ICs. A key design consideration: the 100-TFBGA package demands careful PCB stackup; plan for via-in-pad or dogbone fanout and follow the Microchip SAM3S hardware design guidelines for decoupling all VDDIO/VDDCORE ball pairs. This page adds value beyond the manufacturer datasheet by consolidating distributor pricing, drop-in family alternatives, and practical design notes in one structured reference.

USD $4,89 Em estoque
ATSAM3S4AA-AUR - 64MHz Cortex-M3 MCU, 256KB Flash | Microchip
ATSAM3S4AA-AUR

ATSAM3S4AA-AUR - 64MHz Cortex-M3 MCU, 256KB Flash | Microchip

The Microchip Technology ATSAM3S4AA-AUR is a 32-bit ARM Cortex-M3 flash microcontroller operating at up to 64 MHz, with 256 KB of Flash memory and up to 48 KB of SRAM, supplied in a 48-pin LQFP (7x7 mm) surface-mount package. It runs from a single 1.62V to 3.6V supply over an industrial temperature range of -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals on one die, sitting at the device level of the embedded-systems hierarchy (MCU -> embedded processor -> microcontroller -> system-on-chip). The SAM3S series belongs to the ARM Cortex-M3 class of 32-bit MCUs, which use a 3-stage pipeline Harvard architecture with Thumb-2 instruction set for high code density and deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC). Key features of the ATSAM3S4AA include a Full Speed USB 2.0 Device port with embedded transceiver, a High Speed Multimedia Card Interface (HSMCI) supporting SDIO/SD/MMC, I2C (TWI), SPI, UART and USART serial interfaces, PWM outputs, a 12-bit ADC and a 10-bit DAC, plus brown-out detection/reset and power-on reset for supply supervision. Parallel data capture on the PIO ports allows direct connection of non-standard devices such as low-cost image sensors, with DMA offloading transfers from the CPU. Technically, the device balances performance and power: the Cortex-M3 core executes from fast Flash with a prefetch buffer, and multiple power-management modes (including wait, sleep, and backup) let designers scale consumption in battery-operated products. The 1.62V minimum supply supports operation directly from single-cell Li-IO stacks via regulators, and the industrial grade rating suits harsh environments. Typical applications include industrial control panels, consumer appliances, USB-enabled data loggers, SD-card-based instrumentation, battery-powered metering, and touch or sensor front-ends using the on-chip ADC and PWM channels. A key design consideration: the SAM3S4A is pin-to-pin compatible with the SAM3N4A, so boards can be migrated between series without PCB rework, but USB availability differs between the families - verify the peripheral set before second-sourcing. This page adds value beyond the manufacturer datasheet by consolidating distributor pricing, verified drop-in alternatives, design notes, and an AEO-optimized FAQ in one place.

USD $5,42 Em estoque
ATSAM3S4AA-MU - 64MHz Cortex-M3 256KB Flash MCU | Microchip
ATSAM3S4AA-MU

ATSAM3S4AA-MU - 64MHz Cortex-M3 256KB Flash MCU | Microchip

The Microchip Technology (Atmel) ATSAM3S4AA-MU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 256 KB of embedded flash memory and 48 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package with exposed pad. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die, sitting at the lowest level of the embedded-systems hierarchy: microcontroller -> embedded processor -> SoC. The SAM3S series belongs to Atmel/Microchip's SMART ARM-based MCU family and is pin-to-pin compatible with the legacy AT91SAM7S products in 48- and 64-pin versions, easing migration from older designs. Key features include an ARM Cortex-M3 revision 2.0 core with a Thumb-2 instruction set, a Memory Protection Unit (MPU), a 128-bit-wide flash access with a memory accelerator for efficient 64 MHz execution, and an internal 1.62V-3.6V single-supply operating range. Peripherals include USB 2.0 device, USARTs, SPI, TWI (I2C), 12-bit ADC, PWM channels, and a real-time clock, enabling compact single-chip designs. The Cortex-M3 architecture provides deterministic interrupt handling via the Nested Vectored Interrupt Controller (NVIC) and hardware division, making the device well suited for real-time control loops. The embedded flash controller allows in-system programming and the device supports SWD debug through the serial wire debug port. Typical applications include industrial sensing nodes, consumer HMI devices, USB accessories, battery-powered portable instruments, and legacy AT91SAM7S upgrades where a drop-in performance boost is desired. A key design consideration: the exposed pad of the QFN-48 package must be soldered to a ground plane for both thermal dissipation and signal-integrity reasons; do not treat it as a no-connect. This page adds value beyond the datasheet by compiling verified distributor pricing, same-package drop-in alternatives, application guidance, and cross-reference data not found in the manufacturer documentation.

USD $3,85 Em estoque
ATSAM3S4AA-MUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip
ATSAM3S4AA-MUR

ATSAM3S4AA-MUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM3S4AA-MUR is a 32-bit ARM Cortex-M3 flash microcontroller running at 64 MHz with 256 KB of embedded flash memory and 48 KB of SRAM, housed in a 48-pin QFN (7x7 mm) package with exposed pad. The MUR suffix indicates Tape & Reel packing for automated assembly. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals on one die, sitting at the heart of the embedded-system hierarchy between simple logic devices and full application processors. The SAM3S series is Microchip's (formerly Atmel) medium-range general-purpose MCU family, positioned for designs balancing low power consumption, processing power, and peripheral integration. Key features include the 64 MHz Cortex-M3 core with a 3-stage pipeline and Thumb-2 instruction set, 256 KB (256K x 8) of zero-wait-state flash, and an operating supply range of 1.62 V to 3.6 V. The device integrates a fast 12-bit ADC, an on-chip 1.8 V LDO regulator (VDDOUT), USB 2.0 full-speed device port on SAM3S A-variant peripherals, and parallel data capture mode on the PIOs that collects data from non-standard sources such as low-cost image sensors, with DMA offloading the CPU. Technical depth: the SAM3S architecture pairs the Harvard-architecture Cortex-M3 with an on-chip ARC bus, nested vectored interrupt controller, and 12-channel DMA, enabling peripheral-to-memory transfers without CPU intervention. Flash memory is organized to permit simultaneous read-while-write operation for EEPROM emulation. Power management modes include backup, wait, and sleep, supporting battery-operated designs. Typical applications include industrial sensing and control nodes, consumer appliances, battery-powered portable instruments, USB-connected devices, and image-sensor front ends leveraging the parallel capture mode. Design consideration: operate within the 1.62 V to 3.6 V supply window and decouple VDDIN with the LDO output VDDOUT per the manufacturer datasheet to preserve ADC accuracy and EMC performance. This page synthesizes distributor pricing, verified drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,85 Em estoque
ATSAM3S4BA-AUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip
ATSAM3S4BA-AUR

ATSAM3S4BA-AUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM3S4BA-AUR is a 32-bit ARM Cortex-M3 RISC microcontroller from the SAM3S series, delivering 64 MHz maximum core speed, 256KB (256K x 8) Flash program memory, and 49KB SRAM in a 64-pin LQFP (10x10 mm) surface-mount package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the heart of embedded systems. Within the product hierarchy, the SAM3S sits under ARM Cortex-M3 based flash microcontrollers -> 32-bit MCUs -> embedded processors. The ATSAM3S4BA is a member of Microchip's (formerly Atmel) SAM3S series, a cost-optimized Cortex-M3 family targeting industrial and consumer embedded designs. Key features include the 64 MHz ARM Cortex-M3 RISC core, 256KB of on-chip Flash, 49KB of SRAM, and a rich peripheral set covering HSMCI (high-speed multi-media card interface), I2C, I2S, IrDA, SPI, SSC (synchronous serial controller), TWI, UART, USART, and USB device connectivity. A DMA controller offloads the CPU by moving data directly to memory, improving real-time throughput. Technically, the device operates from a single 1.62V to 3.6V supply (typical 1.8V/3.3V rails), and Microchip documents that it is pin-to-pin compatible with the SAM3N4B and SAM7S64, allowing footprint reuse and BOM migration across the family. The 10x10 mm 64-LQFP with 0.5 mm pitch is hand-solderable and suitable for two-layer and four-layer industrial boards. Typical applications include industrial control nodes, consumer appliances, battery-powered portable instruments, and USB-connected sensor interfaces, where the Cortex-M3 performance, USB device port, and DMA-driven peripherals fit well. When designing with this MCU, budget Flash and SRAM conservatively: 256KB Flash and 49KB SRAM are ample for bare-metal or RTOS-based control firmware, but leave headroom for OTA-style field updates. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3,44 Em estoque
ATSAM3S4BA-MU - Cortex-M3 64MHz MCU 256KB Flash | Microchip
ATSAM3S4BA-MU

ATSAM3S4BA-MU - Cortex-M3 64MHz MCU 256KB Flash | Microchip

The Microchip Technology ATSAM3S4BA-MU is a 32-bit ARM Cortex-M3 flash microcontroller running at up to 64 MHz, with 256KB of embedded Flash and 48KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A flash microcontroller is a single-chip computing device that integrates a processor core, program memory, data memory, and peripherals such as UART, SPI, I2C, ADC, and timers onto one silicon die. Microcontrollers sit at the device level of the embedded-system hierarchy, below SoCs and application processors, and the SAM3S series belongs to the broader ARM Cortex-M MCU family alongside SAM3N, SAM4S, and SAMD product lines from Microchip. Key features include the ARM Cortex-M3 revision 2.0 core with Memory Protection Unit (MPU) and Thumb-2 instruction set, 128-bit wide Flash access with a memory accelerator for near-zero-wait-state execution, and pin-to-pin compatibility with the AT91SAM7S series in 48- and 64-pin versions, which simplifies migration for designs needing more performance. Operating supply is 1.62V to 3.6V with core operation at 1.08V to 1.32V, and the part is rated for industrial temperature ranges. Technically, the SAM3S integrates a multilayer bus matrix, 12-channel DMA controller (PDC), USB 2.0 full-speed device port, and a rich peripheral set including USART, SPI, TWI, PWM, and a 12-bit ADC, allowing deterministic real-time control with low interrupt latency. Typical applications include industrial control and automation, battery-powered portable instruments, and human-machine interface nodes, where the combination of 64 MHz performance, DMA offload, and 1.62V low-voltage operation fits power-conscious designs. A key design consideration is that peripheral-to-pin mapping on the 64-QFN requires careful pin multiplexing review; confirm ADC channel assignments and USB D+/D- routing before locking the PCB footprint. This page synthesizes distributor pricing, drop-in alternatives, design notes, and parametric comparisons not found in the manufacturer datasheet.

USD $5,12 Em estoque
ATSAM3S4BA-MUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip
ATSAM3S4BA-MUR

ATSAM3S4BA-MUR - 64MHz Cortex-M3 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM3S4BA-MUR is a 32-bit ARM Cortex-M3 flash microcontroller in the SAM3S series, running at up to 64 MHz with 256 KB of Flash memory and 48 KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-systems hierarchy: microcontroller unit -> embedded processor -> semiconductor IC. The SAM3S family belongs to Microchip's (formerly Atmel) 32-bit ARM-based MCU portfolio, positioned for cost-sensitive industrial and consumer designs that need more performance than 8-bit parts without the complexity of application processors. Key features of the ATSAM3S4BA-MUR include the 64 MHz Cortex-M3 RISC core with Thumb-2 instruction set, 256 KB (256K x 8) of on-chip Flash for code storage, 48 KB of SRAM, and operation over a wide 1.62V to 3.6V single-supply range. The device is fabricated as a green, RoHS-compliant part, supplied in Tape & Reel (the -R suffix), and rated for industrial temperature ranges. From a technical standpoint, the Cortex-M3 core integrates a nested vectored interrupt controller (NVIC) and offers deterministic interrupt latency, while the SAM3S peripheral set includes DMA that transfers data to memory and offloads the CPU, reducing real-time burden. According to Microchip's product page, the device is pin-to-pin compatible with the SAM3N4B and SAM7S64, enabling easy migration between performance tiers on the same PCB footprint. Typical applications include industrial control panels, consumer appliances, battery-powered metering, and USB-connected embedded devices, where 64 MHz Cortex-M3 throughput, integrated DMA, and low-power operation fit well. A key design consideration: verify Flash size headroom, since pin-compatible SAM3N4B alternatives may offer different peripheral sets even on the same footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotação Em estoque
ATSAM3S4CA-CU - 64MHz Cortex-M3 MCU 256KB Flash | Microchip
ATSAM3S4CA-CU

ATSAM3S4CA-CU - 64MHz Cortex-M3 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM3S4CA-CU is a 32-bit ARM Cortex-M3 flash microcontroller operating at up to 64 MHz with 256 KB of embedded Flash and 48 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package. It belongs to the SAM3S series of Atmel-origin (now Microchip) ARM-based Flash MCUs for low-power embedded systems. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory (Flash for program storage and SRAM for data), and peripherals on one die, forming the lowest layer of the embedded processing hierarchy: ARM Cortex-M3 core -> 32-bit MCU -> embedded processor -> semiconductor. MCUs execute dedicated control tasks in everything from consumer appliances to industrial automation, replacing multi-chip solutions with lower cost and power. Key features of the ATSAM3S4CA-CU include the 64 MHz ARM Cortex-M3 RISC core with Thumb-2 instruction set, 256 KB (256K x 8) of Flash program memory, 48 KB of SRAM, and a wide supply range of 1.62 V to 3.6 V. The device integrates a DMA controller that offloads the CPU for peripheral-to-memory transfers, and it is packaged as a 100-TFBGA (9x9) ball grid array for compact, high-density PCB layouts. Mouser lists it as industrial temperature range with MRL A packing classification. Technically, the SAM3S family implements the Cortex-M3 pipeline with nested vectored interrupt controller (NVIC), and per the Microchip product page for the related ATSAM3S4C variant, the family is pin-to-pin compatible with the SAM3N4C series, giving designers a migration path between entry-level and feature-rich parts. The core runs from an internal supply domain of roughly 1.08 V to 1.32 V (1.2 V typical regulator output) per published parametric data. Typical applications include industrial control and factory automation nodes, battery-powered portable instruments leveraging the low-voltage operating range, and consumer appliances requiring 32-bit processing headroom with USB or serial connectivity. When designing with this device, budget the 256 KB Flash and 48 KB SRAM early: projects that grow past these limits require migration to ATSAM3S8-class devices in the same footprint family. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,95 Em estoque