Gerenciamento de Energia
Subcategorias
Produtos (2819)
ISL80410IBEZ - 40V 150mA Low-Iq LDO | Renesas Electronics
The Renesas Electronics ISL80410IBEZ is a high-voltage, adjustable, low-quiescent-current linear regulator with a 40 V input rating, 150 mA output capability, and an 8-lead SOIC exposed-pad package. It is designed for always-on and keep-alive power paths where low standby current is important. Under normal operating conditions, the ISL80410 accepts a +6 V to +40 V input and consumes only 18 µA at no load. Its positive adjustable output, EN control, and low-quiescent-current behavior suit industrial, communications, instrumentation, and embedded systems that must maintain a local rail while minimizing standby consumption. What is an LDO? A low-dropout regulator, or LDO, is a linear voltage regulator that maintains a stable output voltage using a pass transistor operating near its dropout region. The LDO is part of the linear-regulator, voltage-regulator, and power-management-IC hierarchy. Compared with a switching regulator, an LDO offers a simple topology and typically low output ripple, but its efficiency depends directly on the difference between input and output voltage and the load current. Key features of the ISL80410IBEZ include its adjustable output, 150 mA rated output current, 18 µA no-load quiescent current, and +6 V to +40 V normal input range. The EN pin places the device into a low-quiescent-current state when shutdown behavior is required. The exposed pad in the 8-SOIC-EP package provides a thermal connection to the PCB, which is important because linear-regulator dissipation increases as input-to-output voltage difference and load current increase. The ISL80410 is intended for applications that remain connected to a higher-voltage source but need a controlled local supply. Its low quiescent current helps preserve battery or standby power when the regulated rail is lightly loaded. The adjustable output allows the design to select the required rail voltage with external resistors, while the EN input supports controlled enable and disable sequencing in multi-supply systems. Typical uses include industrial control and automation equipment, communications and networking equipment, test and measurement instruments, automotive or transportation electronics, and low-power embedded systems. The 40 V input capability is useful for 24 V industrial rails and other protected high-voltage systems, provided the regulator’s dropout, thermal, and output-voltage limits are respected. A key design consideration is power dissipation. Estimated linear-regulator dissipation equals the input-to-output voltage difference multiplied by load current; for example, 12 V difference at 100 mA is approximately 1.2 W. Use the exposed pad as a thermal pad and provide adequate copper area according to the manufacturer’s thermal guidance. This page combines verified manufacturer and distributor information with application guidance, parameter comparisons, and practical design notes to help engineers evaluate the ISL80410IBEZ for low-quiescent high-voltage regulation.
ISL8200MIRZ - 10A Current-Share DC/DC Power Module | Renesas
The Renesas ISL8200MIRZ is a complete, stand-alone 10A step-down DC/DC switching power module integrating the PWM controller, power MOSFETs, inductor, and passive components into a single QFN-style surface-mount package. It accepts a 4.5V to 20V input and delivers an adjustable output from 0.6V to 6V at up to 10A continuous load current, with patented current-share architecture that allows multiple modules to be paralleled for higher currents. **Background - What is a DC/DC Power Module?** A DC/DC power module is a complete switch-mode power supply (SMPS) miniaturized into a single IC-style package. Unlike a discrete buck converter, which requires the engineer to select and lay out external MOSFETs, an inductor, and compensation components, a power module embeds all these building blocks inside the device, leaving only input/output bulk capacitors and a feedback resistor divider external. Power modules belong to the broader category of point-of-load (PoL) converters, which sit on the PCB next to the load they power (FPGA core rail, ASIC, SoC). Within the SMPS family tree, a power module sits below the buck converter hierarchy: buck converter -> step-down regulator -> PoL converter -> power module -> integrated power management IC. **Key features** of the ISL8200MIRZ include 10A continuous output current, current-share pin for parallel operation up to 60A (six modules), internal 4.5V/20V MOSFETs, internal inductor, internal feedback compensation, adjustable soft-start, power-good indicator, and over-current/over-voltage/thermal protection. The high level of integration eliminates the design and manufacturing risks associated with discrete buck implementations. **Technical architecture**: The ISL8200MIRZ uses a voltage-mode PWM controller with internal loop compensation. The internal MOSFETs and inductor are co-packaged to minimize parasitic loop inductance, achieving high efficiency (typically >90% at 5V input to 3.3V output at moderate loads) and reduced EMI. The current-share bus allows multiple ISL8200M modules to operate in master-slave configuration with ±10% current matching. **Typical applications** include datacom/telecom equipment (48V-to-PoL), FPGA/ASIC core and auxiliary rails, servers and storage area networks, and industrial point-of-load regulation. Designers favor it where PCB real estate is constrained or where rapid time-to-market outweighs the per-ampere cost of a discrete design. **Design consideration**: Place input bulk capacitors within 5 mm of the module's VIN pins to minimize parasitic inductance, and use the exposed thermal pad for both thermal dissipation and the electrical ground return. The current-share pin must be tied together on all paralleled modules; floating it disables parallel operation. **Unique value**: This page combines distributor pricing, EOL/last-time-buy status, same-family pin-compatible alternatives, and practical parallel-operation notes - information not consolidated on the manufacturer datasheet or distributor product pages.
ISL8200MIRZ-T - 10A DC/DC Power Module, 4.5-20V Input | Renesas
The Renesas ISL8200MIRZ-T is a complete 10 A current-sharing DC/DC power module that integrates a synchronous buck controller, power MOSFETs, and passives into a single 15 mm x 15 mm surface-mount QFN package. Per the manufacturer datasheet, it accepts a 4.5 V to 20 V input range and supplies an adjustable 0.6 V to 6 V output at up to 10 A continuous load current, with parallel current-share capability extending to 60 A using multiple modules. The integrated 26.5 microohm/V high-side FET achieves peak efficiencies of approximately 95% at 12 V input to 3.3 V output at moderate loads. A DC/DC power module is a fully integrated point-of-load (PoL) switching regulator that places the controller, power stage, and most passive components inside one package. Compared with discrete buck regulator designs, modules simplify PCB layout, shrink the BOM, shorten time-to-market, and provide validated thermal performance with a defined exposed thermal pad. ISL8200MIRZ-T sits within the broader taxonomy of DC/DC switching converters > switching voltage regulators > power management ICs > semiconductors. Key features include 4.5 V to 20 V wide VIN range, 0.6 V to 6 V adjustable VOUT (single resistor-set), 10 A continuous output, current-share mode for parallel operation up to 60 A, internal soft-start, thermal protection, and a PGOOD indicator. Programmable switching frequency (200 kHz to 600 kHz) supports efficiency and component-size optimization per design target. The architecture is a voltage-mode synchronous buck converter with adaptive drivers and a current-share loop. The exposed-pad QFN package provides a thermal resistance around 17 C/W (per datasheet), supporting convection-cooled operation up to ~7 W dissipation on a 4-layer JEDEC JESD51 board. Internal compensation simplifies the external BOM to a few ceramic capacitors, a single VOUT setting resistor, and an enable pull-up. Typical applications include FPGA/CPLD core and I/O voltage rails, datacom and telecom PoL supplies, baseband and DSP power, high-current ASIC rails, and industrial controller 3.3 V/5 V/6 V rails. The current-share feature also makes the part suitable for compute boards that need 30 A or more with N+1 redundancy. When designing with the ISL8200MIRZ-T, place input/output ceramic capacitors close to the module's bond-pad islands and solder the exposed pad to at least 1 square inch of 2 oz copper to keep junction temperatures within the datasheet thermal envelope. Always validate ripple at the load using actual bulk capacitors, not the minimum values shown in the schematic. This page integrates distributor pricing, pin-compatible alternatives, application guidance, and design notes not provided on the manufacturer datasheet summary, giving engineers a single source for both sourcing and design decisions.
ISL8282MFRZ - 15A PMBus Step-Down Power Module | Renesas
The Renesas ISL8282MFRZ is a PMBus-enabled 15A hybrid digital step-down DC/DC power module with a 4.5V to 16.5V input voltage range, a 0.5V to 5V adjustable output range, and up to 95% conversion efficiency, housed in a compact HDA-83 (11x12 mm) power module package. A DC/DC step-down (buck) power module is a voltage regulator that integrates the controller, power MOSFETs, gate drivers, and inductor into a single packaged unit. Within the power management IC hierarchy, power modules sit above discrete controllers because they eliminate the most difficult part of buck converter design - power stage layout and magnetics selection - delivering a verified reference design in one solderable component. Key features include 15A continuous output current from a single channel, PMBus/SMBus digital control and telemetry for remote configuration and monitoring, proprietary Renesas R4 Technology control architecture for fast transient response, and integrated LDOs that supply clean internal bias rails and simplify external power tree design. The wide 0.5V to 5V output range covers core rails, I/O rails, and DDR memory VTT-adjacent supplies. Technically, the hybrid digital architecture combines the accuracy of a digital control loop with the power density of an integrated power stage, achieving up to 95% peak efficiency while minimizing the external component count. Digital telemetry enables output voltage, current, temperature, and fault-status readback over PMBus, supporting system health monitoring in server and networking platforms. Typical applications include data center server CPU and ASIC power, networking switch line cards, storage systems, and industrial baseboards where a compact, monitored 15A rail is required. The high power density suits space-constrained boards that would otherwise need multi-component discrete buck stages. Design consideration: verify thermal derating at full 15A load - power modules concentrate dissipation in one footprint, so PCB copper pour area and airflow per the manufacturer thermal application guidance are essential for reliable junction temperatures. This page synthesizes distributor availability data, PMBus feature analysis, and drop-in replacement guidance not found in the manufacturer datasheet.
ISL8282MFRZ-T - 15A PMBus Digital Step-Down Power Module | Renesas
The Renesas ISL8282MFRZ-T is a 15A high-efficiency hybrid digital step-down power module with PMBus interface, supporting a wide 4.5V to 16.5V input voltage range, an adjustable 0.5V to 5V output range, and up to 95% conversion efficiency in a compact board-mount LGA-style package. A digital step-down power module is a non-isolated point-of-load (PoL) DC/DC converter that integrates the power stage, controller, and compensation into a single surface-mount unit. Within the power-management hierarchy it sits above discrete controllers-plus-MOSFET solutions, belonging to the family of voltage regulators, specifically digital switching regulators, and is programmed and monitored over the industry-standard PMBus serial bus. Key features include single-channel 15A continuous output current, PMBus/SMBus telemetry for voltage, current, temperature and fault monitoring, and proprietary Renesas R4 Technology control architecture that enables fast transient response with high power density. Integrated LDOs supply the internal controller circuitry, reducing external component count and simplifying bill-of-materials. The module is optimized for high-density designs where board space and thermal performance are critical. Technically, the hybrid digital architecture combines a digital loop controller with an integrated power stage. The R4 Technology control loop provides fast, stable transient response without external compensation design, and digital telemetry enables real-time margining, sequencing, and fault management. Output voltage can be set through PMBus commands or external configuration, supporting flexible rail deployment across multiple designs. Typical applications include FPGA and ASIC core power rails in networking switches, storage and data-center equipment, industrial automation systems, and optical modules, where 15A continuous current at sub-5V rail voltages with PMBus manageability is required. A key design consideration is thermal management: at 15A and low output voltages, conduction losses dominate, so adequate PCB copper area and airflow must be provided, and input/output capacitor selection should follow the manufacturer datasheet recommendations to maintain stability. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-10-19.
ISL8282MFRZ-T1 - 15A PMBus Step-Down Power Module | Renesas
The Renesas ISL8282MFRZ-T1 is a PMBus-enabled, single-channel hybrid digital step-down DC/DC power module delivering up to 15A of continuous output current from a 4.5V to 16.5V input rail, with an adjustable output range of 0.5V to 5V, packaged in a thermally enhanced 12 mm x 11 mm x 5.3 mm fully encapsulated HDA-83 module. A point-of-load (PoL) DC/DC power module is a device that integrates a switching regulator controller, power MOSFETs, inductor, and most passive components into a single encapsulated package. Within the power management hierarchy, it sits above discrete converters and below complete power supplies, dramatically reducing external component count, design complexity, and board area while guaranteeing optimized internal layout for switching performance. Key features of the ISL8282M include up to 95% peak conversion efficiency, digital PMBus/SMBus control and telemetry for output voltage adjustment, sequencing, margining, and monitoring, plus integrated LDOs that power internal circuitry. The proprietary Renesas R4 Technology control architecture provides fast transient response and stable operation across the full 0.5V to 5V output range. Technically, the hybrid digital architecture combines a digital control loop with integrated power stage magnetics in the HDA package, achieving high power density suitable for space-constrained boards. Fully encapsulated construction protects against moisture and mechanical stress, and the thermally enhanced substrate conducts heat to the PCB for convection cooling without a heatsink at moderate loads. Typical applications include FPGA and ASIC core power rails in networking switches, data-center and server line cards, industrial automation controllers, and wireless infrastructure equipment where digital power telemetry via PMBus is required. For design, ensure adequate copper area under the module thermal pad to keep junction temperature within limits at high load, and follow the datasheet-recommended external capacitor values for input and output stability. This page synthesizes distributor pricing, verified alternatives, and practical design guidance not found in the manufacturer datasheet alone.
ISL854102FRZ-T - 40V 1.2A Sync Buck Regulator | Renesas
The Renesas ISL854102FRZ-T is a wide-input 1.2 A synchronous buck (step-down) DC/DC regulator housed in a 12-pin DFN-12 EP (4x3 mm) package with exposed thermal pad. It accepts a 3 V to 40 V input range, integrates both high-side and low-side NMOS FETs, and supports an adjustable output from 0.6 V up to 34 V. Default switching frequency is 500 kHz, programmable from 300 kHz to 2 MHz via an external resistor. The regulator provides a low-BOM-count, easy-to-use solution for distributed 24 V industrial buses, 12 V/24 V automotive, and general-purpose point-of-load conversion. A synchronous buck regulator (also called a step-down switching converter) is a type of DC-DC converter that uses pulse-width modulation with an integrated or external MOSFET pair to reduce a higher DC input voltage to a lower, regulated DC output voltage. Buck regulators sit inside the broader power management IC (PMIC) hierarchy: switching regulator -> DC-DC converter -> power management IC -> semiconductor. Synchronous variants replace the external Schottky diode with a low-side MOSFET, improving efficiency (typically 90 % to 95 %) and reducing conduction loss compared with asynchronous buck designs. Key features of the ISL854102FRZ-T include internal compensation that eliminates external loop components, PFM mode for improved light-load efficiency, a forced-PWM option for noise-sensitive applications, internal/external soft-start control, and a PGOOD (power-good) output. Protection features include overcurrent protection (OCP), overvoltage protection (OVP), undervoltage lockout (UVLO), and thermal shutdown. The wide 40 V input tolerance makes the part robust against load-dump transients common on 12 V/24 V automotive rails. The ISL854102 uses peak-current-mode control with a fixed internal compensation network, simplifying design-in and reducing external component count to typically one inductor, input/output capacitors, and feedback resistors. The adjustable frequency (300 kHz to 2 MHz) allows designers to trade efficiency against solution size or to avoid AM-band interference. Typical applications include industrial 24 V distributed power systems, 12 V/24 V automotive electronics, telecom point-of-load rails, general-purpose 5 V/3.3 V/1.8 V/1.0 V conversion, battery-powered equipment, and FPGA/MCU supply rails. The combination of 40 V input tolerance, 1.2 A output current, and a small DFN-12 EP footprint makes it particularly attractive for compact industrial designs where space is at a premium. When designing with this device, derate output current versus ambient temperature using the package's thermal resistance; pair the exposed pad with sufficient PCB copper (at least 1 square inch top-side copper). For noise-sensitive loads, disable PFM mode by tying the MODE pin to VIN to force continuous PWM operation. Ensure that the feedback divider uses 1 % resistors and that input capacitance is rated for the full 40 V stress with adequate ripple-current rating. This page synthesizes distributor pricing (DigiKey, Mouser, LCSC, Octopart as of 2026-10-05), drop-in alternatives drawn from same-package same-family Renesas parts, and practical design notes not found in the manufacturer datasheet.
ISL9103AIRUCZ-T - 500mA 2.4MHz Sync Buck 1.8V Fixed | Renesas
The Renesas ISL9103AIRUCZ-T is a 500 mA synchronous step-down (buck) DC/DC converter switching at 2.4 MHz, with a fixed 1.8 V output, supplied from a 2.7 V to 6 V input rail. Housed in a 6-pin UTDFN (UFDFN) 1.6 x 1.6 mm package, it integrates a pair of low-on-resistance P-channel and N-channel MOSFETs to maximize efficiency and minimize external component count, delivering less than 300 mV dropout at 500 mA through 100% duty-cycle operation. A buck switching regulator (also called a step-down converter) is a switch-mode power supply topology that converts a higher DC input voltage into a lower DC output voltage by periodically switching an inductor and rectifying the resulting waveform. Buck regulators occupy the power management IC category alongside LDOs, boost converters, and charge pumps, and are preferred over LDOs whenever input-to-output voltage differential is large because they can exceed 90% efficiency. The ISL9103A family targets low-power point-of-load rails in portable, battery-powered devices where board space is at a premium. Key features include a typical quiescent current that supports long battery standby, 2.4 MHz PWM switching that enables a sub-1 mm profile inductor, internal synchronous rectification that eliminates the external Schottky diode, and built-in protection including overcurrent, thermal shutdown, and soft-start. The 6-pin UTDFN occupies only 1.6 x 1.6 mm of board area, making it suitable for sub-30 mm square power sections in wearables, handsets, and IoT endpoints. The device uses a peak-current-mode PWM control architecture with internal compensation, simplifying external design and providing predictable small-signal response across line and load variation. Internal MOSFETs and synchronous rectification eliminate the need for an external Schottky, while 100% duty cycle extends usable input range when the battery droops toward the output setpoint. Typical applications include powering low-voltage microprocessors in PDAs and cellular phones, single-cell Li+ battery rails in portable media players, and as a post-DCDC point-of-load regulator for application processors in handheld products. A key design consideration is the 2.4 MHz switching frequency: the inductor can be small (typically 1.0 to 2.2 uH), but PCB layout must minimize the input/output loop area to limit radiated EMI from the switching node. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ISL91117IIAZ-T - 4.2A Sync Boost Converter WLCSP-20 | Renesas
The Renesas ISL91117IIAZ-T is a highly-integrated synchronous boost switching regulator delivering up to 4.2A switch current in a 20-ball WLCSP package for battery-powered applications. It accepts input voltages from 1.8V to 4.8V (single-cell Li-ion/Li-polymer or 2-3 cell alkaline/NiMH/NiCd), produces an adjustable output from 0.8V up to the input range and supports 1.5A output at PVIN=3.3V to VOUT=5V. The synchronous rectifier topology and integrated output disconnect maximize efficiency while eliminating external Schottky diode cost. A synchronous boost converter is a switch-mode DC-DC converter that steps the input voltage up to a higher regulated output using an internal high-side MOSFET, an inductor, and a synchronous low-side MOSFET replacing the traditional diode. Within the broader power-management IC hierarchy, the boost converter belongs to step-up switching regulators, which sit alongside buck (step-down), buck-boost, and SEPIC converters. This category trades efficiency against the linear regulator's noise performance: switching converters achieve 90-95% efficiency versus 30-60% for low-dropout (LDO) regulators at large VIN/VOUT deltas, but inject ripple into the output that requires LC filtering. The ISL91117 family targets portable, single-cell Li-ion systems where battery life depends on minimizing quiescent current and maximizing converter efficiency. The ISL91117IIAZ-T integrates two 4.2A N-channel MOSFETs in a synchronous configuration, supports output disconnect (true shutdown), and operates at a fixed switching frequency optimized for small external components. Internal compensation eliminates the need for external compensation networks. The 20-ball WLCSP occupies approximately 2.015 mm x 1.555 mm of board area, enabling ultra-compact portable designs. Protection features include overcurrent protection, over-temperature shutdown, and undervoltage lockout. The wide input range supports direct connection to single-cell Li-ion batteries without front-end regulation. Typical applications include boosting a single-cell Li-ion battery (3.0-4.2V) to 5V USB-OTG rails in smartphones, powering 3.3V subsystems from 1.8V rails in wearable devices, and generating 5V supplies from dual-cell alkaline stacks in portable medical and industrial handheld instruments. The 4.2A switch rating also supports LED flash drivers, audio amplifiers, and other high-current loads requiring voltages above the battery. When designing with the ISL91117IIAZ-T, the critical trade-off is efficiency versus noise: a switching regulator always adds ripple versus an LDO, so for noise-sensitive analog rails downstream LDO post-regulation may still be required. Use the smallest ceramic capacitors that meet the datasheet ESR/ESL guidance to minimize solution size and cost. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the Renesas datasheet, providing engineering context for selecting the ISL91117IIAZ-T versus competing boost converters.
ISL91117IIAZ-T7A - 3.7A Sync Boost Converter, 1.8-4.8V | Renesas
The Renesas ISL91117IIAZ-T7A is a high-efficiency synchronous boost (step-up) switching regulator IC delivering up to 3.7A of switch current from a 1.8V to 4.8V battery input, housed in a 20-bump 2.015mm x 1.6mm WLCSP package. It provides an adjustable output from 0.8V up, supports 1.5A output current at PVIN=3.3V, VOUT=5V, and integrates both the synchronous power MOSFETs and the output disconnect switch to prevent reverse conduction into the battery source. A boost converter (step-up DC-DC switching regulator) accepts an input voltage lower than the desired output voltage and uses a switching inductor, peak-current-mode controller, and synchronous rectifier to efficiently generate higher output voltages. Boost regulators sit within the broader hierarchy of switching regulators -> DC-DC converters -> power management ICs -> power management semiconductors. They are essential when downstream analog, RF, or MCU rails require 3.3V, 5V, or higher from a single-cell Li-ion/alkaline source. Key features include 95% peak efficiency, internal 4.2A low-Rdson MOSFET switches, output disconnect during shutdown, programmable PFM/PWM operation for light-load efficiency, and an operating junction temperature range of -40C to +85C. The wide VIN range supports dual/triple-cell alkaline, NiCd/NiMH, and single-cell Li-ion/Li-polymer battery packs. The ISL91117IIAZ-T7A uses a peak-current-mode architecture with internal compensation and synchronous rectification to maximize efficiency across the entire load range. The output disconnect MOSFET eliminates leakage paths in shutdown, allowing true output isolation - critical for USB-OTG and battery-powered designs where back-feeding the battery would damage cells or waste energy. Typical applications include single-cell Li-ion powered portable electronics (smartphones, wearables, Bluetooth headsets, e-readers, tablets, point-of-sale terminals, GPS receivers, medical handheld devices), USB-OTG 5V boost supplies from a 3.0-4.2V Li-ion source, and any 2-cell-to-5V boost conversion where PCB area and efficiency both matter. When designing with this part, place input/output ceramic capacitors as close as possible to the IC bumps, use a 1.0uH to 4.7uH shielded inductor with low DCR, and ensure the feedback divider uses 1% resistors. Thermal management is easier than linear regulators - switching losses dominate, but at 95% efficiency dissipation stays low. This page synthesizes distributor pricing, drop-in alternatives in the same WLCSP-20 footprint, and practical design notes that go beyond the manufacturer datasheet - useful for engineers selecting parts during BOM review and second-source qualification.
ISL9205AIRZ - 900mA Li-Ion/Li-Polymer Charger IC | Renesas
The Renesas ISL9205AIRZ is an integrated single-cell Li-ion or Li-polymer linear charger IC housed in a 10-pin DFN (3x3 mm) package with an exposed thermal pad. The device accepts input voltages from 2.5V to 6.5V and delivers programmable charge current from 50 mA to 900 mA at a fixed 4.2V termination voltage, making it a compact solution for space-constrained portable designs. The -A variant is the version with no safety timer and uses an external V-sense resistor for current sensing. A linear Li-ion charger IC is a power management device that regulates current and voltage from a DC source (typically USB or AC adapter) into a rechargeable lithium-ion or lithium-polymer cell. Unlike switching chargers, linear chargers dissipate the excess input-to-battery voltage as heat, trading efficiency for smaller BOM size, lower EMI, and simpler PCB layout. Within the broader power management hierarchy, the ISL9205AIRZ sits at: battery management IC -> charger IC -> linear charger -> power management IC. Key features of the ISL9205AIRZ include 1% charge voltage accuracy over the full operating range, integrated MOSFET pass element, automatic recharge of a depleted battery, built-in thermal regulation that folds back charge current at high die temperatures, and a CHRG output pin for LED status indication. The -A suffix indicates the variant with no internal safety timer, allowing the system controller to handle termination externally. The ISL9205 uses an external low-side current-sense resistor between VBAT and the battery to set the charging current via the ISET pin. Its 2.5V minimum input voltage enables charging from low-voltage sources including solar panels or weak USB ports. The exposed thermal pad on the DFN-10 package provides a low thermal resistance path critical for dissipating the linear charger losses at high charge currents. Typical applications include wearable health devices, Bluetooth headsets, portable medical sensors, single-cell power banks, IoT sensor nodes, and backup battery charging for industrial data loggers. The device's tiny 3x3 mm footprint and minimal external component count (typically 5-7 parts) make it especially attractive in designs where PCB area is at a premium. When designing with this part, calculate the worst-case power dissipation as (VIN_max - 4.2V) x Icharge. At 5V input and 900 mA charge current, this is 0.72 W, requiring attention to the copper area beneath the exposed pad to keep junction temperature within safe limits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.
ISL95833BIRTZ - Dual 2+1 PWM Controller, IMVP-7/VR12 | Renesas
The Renesas ISL95833BIRTZ is a dual 2+1 Pulse Width Modulation (PWM) controller implementing the company's Robust Ripple Regulator (R3) modulation scheme, purpose-built for Intel IMVP-7 / VR12 compliant microprocessor and graphics-processor core voltage regulators. Housed in a 32-lead QFN (4x4 mm) package with an exposed thermal pad, the controller integrates gate drivers for two rails: VR1 (VCORE) supports 2-phase or 1-phase operation, while VR2 (typically graphics) operates as a single-phase rail, giving designers a flexible 2+1 multiphase topology from a single IC. Switching frequency is programmable from 400 kHz to 600 kHz, output voltage is set from 0.25 V to 1.52 V, and the controller can deliver up to 60 A when paired with external DrMOS/DrIV stages. A PWM controller is the central feedback element in a multiphase synchronous buck converter: it senses the output voltage, compares it with the internal DAC reference commanded by the IMVP-7/VR12 SVID bus, and modulates the duty cycle of each phase to regulate the core voltage of a CPU or GPU under rapidly changing load conditions. The ISL95833B's R3 modulation provides faster transient response than traditional voltage-mode or current-mode controllers by injecting ripple-compensation current directly into the modulator, which is critical for the sub-microsecond load steps generated by modern mobile CPUs entering and exiting low-power states (P-states, C-states). Key features include differential remote-sense inputs for accurate regulation at the load, programmable per-phase current limiting with inductor DCR sensing, automatic phase-dropping at light load, OVP/UVP/OCP protection, and a thermal-shutdown block. The device communicates with the processor through the Intel VR12/IMVP-7 serial VID (SVID) interface, accepting 8-bit VID codes plus commands such as SetVID, SetPS, and Slew-Rate. The exposed-pad QFN-32 package delivers a low thermal resistance suitable for the notebook thermal envelope. Typical applications include ultrabook and notebook CPU core rails, IMVP-7 compliant tablet SoC supplies, and integrated graphics (iGPU) rails where two rails must be regulated from one controller. The part also fits ultrathin laptop platforms that demand a single-controller solution to reduce BOM count and PCB area versus a two-controller design. When designing with the ISL95833B, lay out the boot/boot-mid capacitors, SVID pull-ups, and the IMON summing network per the reference schematic in the datasheet, and verify DrMOS compatibility because the ISL95833B's integrated driver targets specific Renesas/Intersil DrMOS families. A 4-layer PCB with a solid ground plane under the exposed pad is required to keep junction temperature within the 125 C operating limit.
ISL95833HRTZ - IMVP-7/VR12 Dual 2+1 PWM Controller | Renesas
The Renesas ISL95833HRTZ is a dual 2+1 PWM controller IC designed for IMVP-7/VR12 compliant microprocessor and graphics processor core voltage regulators, integrating two voltage regulator control loops plus one integrated driver in a 32-pin QFN-EP (4x4 mm) package. The device delivers a programmable output range of 0.25 V to 1.52 V supporting up to 60 A and uses Intersil's proprietary Robust Ripple Regulator (R3) modulation technology to deliver superior transient response and DC accuracy. An IMVP-7/VR12 PWM controller is a multiphase buck-control IC that converts a higher DC bus voltage (typically 19 V from an adapter or 12 V from a battery) into the sub-1.5 V core rail demanded by modern Intel CPUs. The ISL95833 sits in the broader hierarchy of multiphase controllers -> DC-DC controllers -> voltage regulators -> power management ICs -> semiconductors. Compared with simpler voltage-mode or single-phase controllers, R3-based multiphase devices trade higher pin/packaging complexity for vastly improved load-step response, lower ripple at the load, and the ability to scale current by adding phases. Key features include 2+1 phase architecture (one VR for V_CORE with integrated 2-phase driver, plus a second VR for graphics/system agent), ±0.5 % system accuracy, automatic phase shedding at light load, and full IMVP-7/VR12 protocol compliance including PVID, SVID, and power-state transition support. The on-chip high-side and low-side gate drivers reduce external MOSFET count, while differential voltage sensing and per-phase current balancing improve regulation accuracy under dynamic loads. The architecture combines a high-bandwidth error amplifier, a precision internal reference, programmable dead-time control, and per-phase current sharing. The 32-pin QFN exposed-pad package provides a low thermal resistance path (theta_JA approximately 36 C) for thermal management of the integrated drivers, and an I2C/SMBus interface enables telemetry, fault logging, and configuration. Typical applications include IMVP-7/VR12 notebook CPU core rails, ultrabook and Ultrabook-class platforms, gaming laptop GPU rails, and embedded computing modules with VR12-compatible processors. The wide input range (typically 4.5 V to 25 V) supports 2-cell/3-cell Li-ion battery systems plus adapter boosting, and the integrated driver topology is favored where PCB area is constrained and BOM count must be minimized. When designing with the ISL95833HRTZ, place the input sense resistor and phase inductors within 10 mm of the controller to minimize parasitic ESL, and connect the exposed pad to a continuous ground copper pour for thermal dissipation. Verify the IMVP-7/VR12 protocol timing budget against your platform's VR12.5 extension requirements, since the ISL95833 does not natively support VR12.5/VR13 voltages above 1.52 V. This page synthesizes distributor pricing, application-specific design notes, and drop-in compatibility data sourced from the manufacturer datasheet and authorized distributors - information not consolidated on any single distributor product page.
ISL95833HRTZ-T - Dual 2+1 PWM Controller IMVP-7/VR12 | Renesas
The Renesas ISL95833HRTZ-T is a dual 2+1 pulse-width modulation (PWM) controller designed for IMVP-7/VR12 compliant microprocessor and graphics-processor core voltage regulators, housed in a 32-pin QFN-EP (4x4 mm) package. It integrates two voltage regulators with output capability up to 60 A and an output voltage range of 0.25 V to 1.52 V, suiting it for high-current CPU Vcore and GPU core power rails in notebook platforms. The first VR (typically Vcore) incorporates 1 integrated driver and can operate in 2- or 1-phase configurations, while the second VR handles graphics-processor or system-agent power. A PWM controller is a switch-mode power-supply control IC that regulates an output voltage by varying the duty cycle of a switching stage. IMVP-7 (Intel Mobile Voltage Positioning) and VR12 are Intel-defined voltage-regulator specifications that combine a multi-phase buck topology, dynamic VID, current balancing, and protection telemetry to power modern x86 processors. The ISL95833 sits between the IMVP-7/VR12 controller hierarchy and the discrete power stage, providing the analog control loops and digital telemetry that the CPU expects. Key features of the ISL95833HRTZ-T include dual independent current-mode PWM modulators, integrated MOSFET drivers, differential voltage error amplifier, programmable dynamic VID, droop and offset compensation, per-phase current balance, and comprehensive protection (OVP, UVP, OCP, OTP). The current-mode architecture provides line-transient rejection and per-cycle current limiting, while the integrated driver eliminates external gate-driver ICs for Vcore, reducing BOM and PCB area in thin notebook designs. Typical applications include Intel IMVP-7/VR12 notebook Vcore rails, integrated graphics (iGPU) regulators, system-agent rails, and embedded computing platforms requiring IMVP-7-compliant multiphase buck control. The 32-pin QFN-EP package exposes a thermal pad for direct copper heatsinking to keep junction temperatures within limits under sustained 60 A output conditions. When designing with this controller, follow the datasheet IMVP-7/VR12 reference schematic, including the recommended inductor, MOSFET pair, and sense-resistor selection to meet Intel transient and DC tolerance windows.
ISL95866CHRZ - 4+3 Phase R3 PWM Desktop VR Controller
The Renesas Electronics ISL95866CHRZ is a 4+3-phase Robust Ripple Regulator (R3) PWM controller for Intel IMVP8 desktop processor power systems, with two configurable voltage-regulator outputs in a 52-QFN 6x6 mm package. Its first regulator supports 4, 3, 2, or 1 phases, while its second regulator supports 3, 2, or 1 phases. It is designed for desktop microprocessors requiring independent core (IA), graphics (GT), or unsliced graphics (GTUS/GTX) rails. The verified product listing identifies the device as a dual-output, IMVP8-compliant desktop voltage-regulator IC. Renesas describes it as a complete controller solution with control and protection functions for two processor VR domains, and the device-family page specifically identifies SMBus support for ISL95866C variants. A multiphase PWM controller is a power-management IC that coordinates several external power stages to deliver high-current, low-ripple processor voltages. A phase count such as 4+3 describes parallel regulator channels under one control solution; it does not mean that the controller itself delivers the full processor current. External MOSFETs, inductors, capacitors, sensors, and the motherboard power architecture determine the resulting current capability and transient response. The R3 architecture is intended for ripple-sensitive, high-performance desktop CPU and GPU power delivery. The verified listing specifies a 52-QFN package measuring 6x6 mm and two outputs. The family information confirms flexible phase configurations: 4-, 3-, 2-, or 1-phase operation for the first VR and 3-, 2-, or 1-phase operation for the second VR. The Renesas product page also identifies Intel IMVP8 desktop CFL/CNL CPU support in its ISL95866C description. Detailed electrical limits, switching frequency, voltage ranges, current limits, SMBus address information, pin functions, and thermal ratings were not included in the supplied web excerpts and must be checked against the manufacturer datasheet before design release. The controller is positioned for desktop motherboard power systems where the processor requires separately regulated core and graphics domains. It can support platform configurations that assign the first output to IA and the second to GT, or use unsliced GTUS/GTX rails where supported by the platform. The external power stage must be designed around the controller's control outputs and the CPU's load transient requirements. Because the package has 52 leads and uses a fine-pitch QFN footprint, PCB layout requires careful escape routing, exposed-pad thermal management, and high-speed control-loop layout discipline. A key design consideration is that controller selection alone does not determine regulator performance. MOSFET resistance, inductor sizing, capacitor ESR and effective capacitance, current sensing, compensation, Vdroop behavior, and layout determine much of the final ripple, efficiency, and transient behavior. The correct replacement or upgrade must therefore be validated at the pin, electrical, firmware, and platform level rather than by package appearance alone. The family page is the appropriate starting point for configuration and application selection, while the device datasheet and Intel power-design guidelines should govern implementation. This page synthesizes the verified distributor identity, official Renesas family description, package information, phase configuration, and practical sourcing context into an engineering-oriented reference. It distinguishes confirmed facts from parameters not present in the supplied excerpts and avoids treating generic regulator attributes as verified ISL95866CHRZ specifications.
ISL95866CHRZ-T 4+3-Phase IMVP8 PWM Controller | Renesas
The Renesas Electronics ISL95866CHRZ-T is a Robust Ripple Regulator PWM controller for Intel IMVP8 desktop microprocessors, with configurable 4+3-phase dual-output control in a 52-QFN (6x6 mm) exposed-pad package. It supports core IA, graphics GT, and unsliced graphics GTUS or GTX rails and provides control and protection for two voltage regulators. The first regulator supports 4-, 3-, 2-, or 1-phase operation, while the second supports 3-, 2-, or 1-phase operation. A multiphase PWM controller is a specialized voltage-regulator control IC that coordinates multiple power stages to deliver high-current processor rails efficiently. It belongs to the PWM-controller, voltage-regulator, and power-management-IC hierarchy. By distributing current across phases, it supports compact desktop-computing power systems while providing the monitoring, control, and protection functions required by high-performance microprocessors. The verified product information identifies the ISL95866C as an Intel IMVP8-compliant, two-output controller with configurable phase counts. Its first regulator can be assigned to IA, GT, or GTUS operation according to the power-architecture configuration. The 52-QFN exposed-pad construction supports surface-mount integration and provides a designated underside thermal connection, although electrical, thermal, timing, and pin-function limits must be taken from the manufacturer datasheet before design release. The controller is intended for desktop CPU and workstation power systems requiring dual high-current rails. Relevant deployments include IA core supplies, integrated graphics supplies, and unsliced graphics rails used by Intel IMVP8 platforms. Renesas positions the device as a complete controller solution; external power stages, inductors, capacitors, MOSFET drivers or power devices, and the processor's specified power-delivery network remain part of the complete regulator design. A primary design consideration is IMVP8 power sequencing, telemetry, protection, and phase assignment. Engineers should follow the manufacturer reference implementation and datasheet layout guidance for the exposed pad, high-current paths, sensing connections, compensation, and debug interfaces. Pin definitions and exact electrical limits cannot be reconstructed from distributor summaries, so the complete 52-pin map and timing or current thresholds must be verified from the official Renesas documentation. This page synthesizes verified manufacturer and distributor information, strict drop-in-replacement screening, application context, and practical design guidance. It does not infer missing electrical values or present packaging-only variants as substitutes.
ISL97901CRZ-T7A - 4-Ch RGB LED Driver, 1.5A, Buck-Boost | Renesas
The Renesas ISL97901CRZ-T7A is a highly integrated four-channel RGB LED driver with buck-boost topology and built-in color sequencing and automatic white-balance calibration, packaged in a 28-lead QFN (4x5 mm). It supports up to 1.5 A per channel in sequential drive and operates from a single-cell Li-ion battery or any regulated source from 2.7 V to 5.5 V, making it ideal for portable display backlight and indicator applications. The IC combines four constant-current sinks with an integrated DC-DC regulator that automatically selects buck or boost mode so the LED forward voltage is regulated regardless of battery state-of-charge. A LED driver is a power-management IC that converts a battery or bus voltage into precisely controlled DC current for one or more light-emitting diodes. Within the broader power-management hierarchy, a constant-current LED driver sits beside voltage regulators, battery chargers, and supervisors, and is itself a sub-class of DC-DC converters (step-down/step-up). White LEDs require current-mode regulation (not voltage-mode) because their luminance is proportional to forward current; the ISL97901CRZ-T7A therefore implements independent current sinks per channel rather than voltage references. Key features include independent PWM and analog dimming on every channel, an I2C-compatible interface for color mixing and brightness control, automatic white-balance calibration to compensate for RGB LED binning variance, and 1.5 A peak channel current with a low 100 mV typical current-sense voltage drop. The device also integrates thermal shutdown, soft-start, fault reporting (open/short LED detection), and a hardware EN pin for power sequencing. Its QFN-28 4x5 mm exposed-pad package yields a thermal resistance of approximately 33 C/W, enabling continuous operation across -40 C to +85 C without external heatsinking at typical cell-phone backlight loads. Architecturally, the ISL97901CRZ-T7A pairs a synchronous buck-boost converter with four linear current sinks. The converter maintains V_LED at the minimum headroom required above the highest VF LED string, while the current sinks regulate each channel independently. Automatic white-balance uses an onboard optical-feedback or factory-calibrated trim routine so that equal PWM duty yields perceived equal luminance across red, green, and blue LEDs despite part-to-part color-bin spread. Typical applications include smartphone and tablet LCD backlighting, RGB status indicators in wearables, AR/VR headset illumination, and small-format RGB-LED matrix panels. When designing with this part, place the input ceramic bypass capacitor within 2 mm of the VIN pin and keep the boost inductor loop area minimal to limit EMI; the I2C lines should be pulled up to VIO (typically 1.8 V) rather than VIN to match modern application-processor I/O domains.
ISL97901CRZ-TK - 4-Channel RGB LED Driver, 1.5A, 28-QFN | Renesas
The Renesas ISL97901CRZ-TK is a highly efficient four-channel, 1.5A sequential RGB LED driver with integrated buck-boost conversion, housed in a 28-pin QFN (4x5 mm) package with exposed pad. The device operates from a single-cell Li-ion battery or any regulated input voltage up to 5.5V, and it incorporates an independent current-controlled driving mechanism for each LED channel, enabling accurate brightness control via I2C dimming at 375 mA per channel. A buck-boost LED driver is a type of power management IC that combines a step-down (buck) and step-up (boost) converter topology so that the output voltage can be either higher or lower than the input voltage while still maintaining a constant current to the LED string. Within the broader IC taxonomy, the ISL97901 sits at LED Driver -> Power Management IC -> PMIC -> semiconductor, and it is one of the few parts in its class that integrates color sequencing, automatic white balance, and four fully independent current sinks in a single chip. Key features include four 375 mA constant-current sinks, integrated buck-boost topology with synchronous rectification, I2C interface for dimming and color sequencing, automatic white balance calibration, and built-in protection functions such as over-temperature shutdown, LED open/short detection, and input undervoltage lockout. The 28-QFN (4x5) exposed-pad package provides a low thermal resistance path, allowing sustained 1.5 A sequential drive without external heatsinking. Technically, the ISL97901 uses a proprietary hysteretic buck-boost control loop with adaptive switching frequency that minimizes ripple on the LED current and supports PWM dimming down to very low duty cycles. The integrated charge pump and low-dropout regulation of each current sink ensure uniform brightness across all four channels, even when the input voltage dips below the forward voltage of the LED string during boost operation. Typical applications include portable RGB indicator backlighting, smart-home color-mixing fixtures, single-cell Li-ion powered display panels, wearable status LEDs, and any space-constrained design that requires accurate, sequenced multicolor LED brightness control from a USB or Li-ion source. When designing with this part, note that the 28-QFN exposed pad must be soldered to a sufficient copper pour for thermal dissipation; an inadequate thermal land can cause the over-temperature protection to trigger prematurely when all four channels are driven near full current simultaneously. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
ISL99125B - 25A DrMOS Power Module | Renesas
The Renesas ISL99125B is a 25A DrMOS power module with integrated high-side and low-side MOSFETs, a high-performance FET driver, and diode emulation in a 24-QFN package measuring 3.5 mm by 5 mm. It is designed for high-frequency, high-density DC/DC power conversion, combining a power stage and driver in one package to reduce external component count and simplify converter layout. The verified listing identifies the device as an ISL99125B 25A/35A DrMOS family device and describes it as suitable for high-frequency power conversion. A DrMOS module is an intelligent power semiconductor stage that combines a MOSFET power stage with its driver. In a synchronous buck or similar converter, the module switches the input rail into a controlled energy-transfer path while its internal driver supplies gate-drive voltage and timing. Diode emulation allows the low-side conduction behavior to be controlled to reduce reverse-recovery effects and improve conversion efficiency. This integration can shorten the critical power loop and make compact converter designs more practical than discrete driver-plus-MOSFET implementations. The ISL99125B family description highlights high-performance DrMOS operation for high-density DC/DC converters. The verified product-page snippet does not provide complete electrical tables, switching-frequency limits, voltage ratings, thermal-resistance values, or monitor accuracy, so those parameters are not inferred here. Engineers should use the official Renesas datasheet for exact limits, recommended operating conditions, pin functions, exposed-pad requirements, and application-specific derating. Typical uses include CPU and GPU point-of-load converters, server power rails, telecom and networking equipment, high-current industrial modules, notebook power systems, and other compact synchronous converters. The module is especially relevant when the PCB area available for discrete MOSFETs is limited and the converter requires high switching performance. The integrated current and temperature-monitor feature described in the verified results can support system telemetry, protection, and power management when configured according to the datasheet. For layout, place power connections and decoupling according to the Renesas datasheet and keep the high-current loop as compact as practical. Validate junction temperature, current capability, gate-drive settings, dead time, switching-node overshoot, and output ripple in the final converter rather than relying on nominal current ratings alone. The package also requires attention to exposed-pad soldering and thermal via or copper design for repeatable performance. This page combines the verified Renesas product description, manufacturer datasheet link, distributor package identification, and cross-reference research. It is intended to help engineers locate the correct documentation and understand the module class without filling missing electrical values with assumptions.
ISL99135B - 35A QFN DrMOS Power Module | Renesas
The Renesas ISL99135B is a 25A/35A DrMOS power module integrating a high-performance FET driver and MOSFETs in a 24-terminal QFN package for high-frequency synchronous DC/DC conversion. It is specified for a 5V nominal input rail, with a 4.75V minimum input voltage and a 5.25V maximum input voltage. The module combines a driver, integrated Schottky bootstrap diode, MOSFET pair, diode-emulation operation, and PS4 support to support high-density buck voltage regulators. A DrMOS module is an integrated driver-and-switch power stage used to place the control and switching functions close to the power conversion path. Its position in the power hierarchy is DrMOS module, integrated power stage, synchronous buck converter, DC/DC converter, and power-management IC. Integrating the driver and MOSFETs can reduce external switching-path inductance and simplify high-current converter layouts while retaining the regulation functions of an upstream controller. The verified product information identifies ISL99135B as a 25A/35A device with diode emulation and PS4. Its integrated Schottky bootstrap diode supports the high-side driver arrangement required by a synchronous buck stage. The 24-terminal QFN package and stated 35A capability make the module relevant to compact, high-frequency power-conversion designs where external discrete high-side and low-side MOSFET arrangements become layout-constrained. Detailed electrical limits and switching characteristics remain subject to the manufacturer datasheet. The ISL99135B is intended for high-density synchronous DC/DC power conversion, particularly designs using an external multiphase or voltage-regulator controller. Its integrated driver and MOSFET pair reduce the number of discrete power devices that must be placed around the switching node. Diode emulation can be useful when the design requires controlled negative inductor current behavior, while PS4 support identifies a specific Renesas power-stage feature whose exact implementation must be confirmed from the datasheet. Typical applications include CPU and GPU voltage-regulator modules, server and networking power conversion, point-of-load supplies, telecommunications equipment, and other compact high-current rails. For these systems, the 5V input range, integrated DrMOS architecture, 25A/35A current classification, and 24-terminal QFN package are the primary selection points. The controller, inductor, input capacitors, output capacitors, and layout still determine whether the complete converter meets transient, thermal, and efficiency targets. Designers should verify the exact pinout, electrical limits, recommended gate-drive conditions, thermal data, and exposed-pad connection directly from the Renesas datasheet before layout release. High-current DrMOS layouts require short switching paths, carefully placed input and output capacitors, adequate copper for thermal dissipation, and layout techniques that minimize high-di/dt loops. The QFN module should be treated as a power semiconductor package when evaluating thermal and safe-operating-area requirements.
ISL99227FRZ-T - Smart Power Stage 60A PQFN-32 | Renesas
The Renesas ISL99227FRZ-T is a Smart Power Stage (SPS) module with integrated high-side and low-side MOSFETs, gate driver, and high-accuracy current and temperature monitors, housed in a 32-pin PQFN (5x5 mm) package. Designed to pair with ISL68xxx/ISL69xxx Digital Multiphase (DMP) controllers or the ISL6617A phase doubler, it delivers up to 60A per phase in synchronous buck multiphase DC/DC systems for CPU/GPU core rails. What is a Smart Power Stage? A Smart Power Stage is a fully integrated power block that combines the synchronous buck MOSFETs, driver IC, and telemetry (current-sense, temperature-sense) into a single package. It sits downstream of a multiphase PWM controller and replaces the discrete DrMOS-plus-shunt-sensor stack, simplifying PCB routing, shrinking loop inductance, and improving efficiency at high switching frequencies (typically 600 kHz to 2 MHz). Smart Power Stages belong to the broader hierarchy: power MOSFET driver / DrMOS -> power management IC -> semiconductor. Key features include a 3.3V/5V-compatible tri-state PWM input, integrated fault protection (UVLO, over-temperature, over-current), an open-drain fault flag (FAULT#), and accurate IMON/ITMON analog telemetry outputs. The integrated current monitor eliminates the external inductor DCR sense network and its associated NTC thermistor, reducing BOM count and improving accuracy across temperature. Typical applications include VR12.5/VR13 server and datacenter core regulators, networking ASIC and FPGA rails, telecom DC/DC bricks, and high-current GPU/CPU multiphase VRs where each phase uses one ISL99227. The tri-state PWM interface ensures robust start-up and clean shutdown with the ISL68xxx/ISL69xxx family controllers, while the integrated protections let the system meet server-grade reliability requirements without a separate supervisor IC. Designers should pair this part with a multiphase controller such as ISL68127 or ISL69147 (same Renesas family) and add 4x 22uF ceramic input capacitors plus a 1uF bootstrap cap per phase. The PQFN-32 exposed pad is the primary thermal path - use a 4-layer PCB with at least 1 sq-in top copper pour for 60A operation; thinner PCBs will trip OTP. Estimate: with 12V VIN, 1V VOUT, 60A load, 94% efficiency, dissipation is ~3.8W per phase and theta_JA must stay under 10 C/W for safe Tj<125C.
ISL99227IRZ-T - 3.3V Smart Power Stage | Renesas
The Renesas Electronics ISL99227IRZ-T is a 3.3 V Smart Power Stage (SPS) module with integrated high-accuracy current and temperature monitors, supplied in a 32-lead PQFN package measuring 5 mm by 5 mm. It is designed for use with Renesas ISL68xxx and ISL69xxx Digital Multiphase controllers and with the ISL6617A phase doubler. The module combines power-stage integration, monitoring, and controller feedback functions in one compact device. A Smart Power Stage is a power-management module that integrates a high-side switching device, driver circuitry, monitoring functions, and fault protection for multiphase DC/DC conversion. In the power hierarchy, an SPS is a specialized power-management IC used inside digital multiphase voltage regulators. It is intended for high-current processor, computing, and telecom rails where multiple phases improve transient response and simplify current sharing. The verified product information identifies the ISL99227 and ISL99227B family as compatible with ISL68xxx and ISL69xxx digital multiphase controllers and with the ISL6617A phase doubler. Integrated high-accuracy current and temperature monitors can be fed back to the controller or doubler, helping complete a multiphase DC/DC system. The supplied family datasheet information also identifies a tri-state PWM input compatible with 3.3 V and 5.0 V signaling, along with UVLO, over-temperature, and overcurrent protection. The ISL99227IRZ-T is associated with controller PWM interface packaging described by distributors as 32-PQFN, 5 mm by 5 mm. Its monitor outputs and fault signals allow the companion controller to supervise phase operation, while the integrated protection functions address abnormal operating conditions. The package and electrical limits must be confirmed against the manufacturer datasheet before layout or replacement decisions are finalized. Typical applications include multiphase DC/DC converters for high-current processors, computing systems, communication equipment, and other power rails requiring accurate phase-current and temperature feedback. Designers should place high-current connections carefully, provide the required input and bootstrap capacitance, route monitor and fault signals away from noisy power paths, and validate thermal performance under worst-case phase current. The key design consideration is controller interoperability. The PWM interface, monitor polarity, fault behavior, package footprint, and protection thresholds must match the selected controller or phase doubler. This page summarizes verified product identity, package information, sourcing records, and design context; exact electrical ratings and layout guidance remain subject to the manufacturer datasheet.
ISL99390FRZ-TR5935 - 90A Smart Power Stage | Renesas
The Renesas Electronics ISL99390FRZ-TR5935 is a 90 A Gen2 Smart Power Stage (SPS) module with integrated high-accuracy current and temperature monitors, supplied in a 39-PowerWFQFN package measuring 5 mm by 6 mm. It is designed for high-current synchronous DC-DC conversion and power-management systems where integrated monitoring, protection, and compact integration are important. The verified distributor listing identifies the device as a half-bridge NMOS driver for DC-DC converters. A Smart Power Stage is an integrated power-conversion module that combines high-side and low-side switching functions with gate-drive circuitry and system monitoring. It belongs to the broader hierarchy of DC-DC converter power stages, power-management ICs, and semiconductor modules. By integrating the power switching and monitoring functions into one package, an SPS can simplify layout and reduce the number of external power components compared with discrete implementations. Verified product information identifies a 90 A current rating, Gen2 SPS architecture, and integrated current and temperature monitors. The device is associated with a 16 V-class power-stage product listing in distributor data, while one alternate distributor description states a 4.5 V to 24 V input range. Because the supplied data contains conflicting voltage descriptions, the detailed manufacturer datasheet should be consulted before selecting the device for a specific converter. Typical applications include high-current voltage-regulator modules for processors and accelerators, server and networking power systems, point-of-load converters, and other synchronous buck or multiphase power-conversion designs. Its 90 A rating makes it relevant to power stages requiring substantial output current, but the exact phase count, switching frequency, protection behavior, and electrical limits must be confirmed from the Renesas datasheet. Designers should verify the controller protocol, PWM and enable logic, current-sense connection, temperature-monitoring interface, exposed-pad thermal path, and recommended PCB layout before using this part in a new board. The integrated monitors can improve fault detection, but they do not eliminate the need for accurate layout, current-loop compensation, and thermal validation. XAIPART provides the official product page, distributor listings, and the manufacturer datasheet link for engineering review.
ISO1042BDW - Isolated CAN Transceiver, 5Mbps, ±70V Bus Fault | TI
The Texas Instruments ISO1042BDW is a galvanically isolated CAN (Controller Area Network) transceiver in a 16-pin SOIC (DW) package that meets the ISO11898-2 (2016) standard. It supports data rates up to 5Mbps in CAN FD mode and provides ±70V DC bus fault protection with a ±30V common-mode voltage range. The integrated digital isolator delivers 5000 VRMS withstand voltage, eliminating the need for an external isolated DC-DC converter. An isolated CAN transceiver is a type of interface IC that combines a CAN protocol engine and a high-voltage capacitive or magnetic isolation barrier in a single package. It belongs to the broader hierarchy of digital isolators > interface ICs > integrated circuits > semiconductors, providing the physical-layer (PHY) bridge between a low-voltage CAN controller and a high-voltage CAN bus while blocking ground-potential differences and transient surges. Key features include basic and reinforced isolation variants, ±70V DC bus fault tolerance (12V typical operating range), ±30V common-mode range, and a 5Mbps flexible data rate (CAN FD). The integrated galvanic isolation replaces discrete optocoupler-based solutions, reducing PCB footprint by up to 80% and improving reliability. Internal logic-level translation supports 1.8V, 3.3V, and 5V microcontroller I/O without external level shifters. Typical applications include industrial CAN bus networks, building automation HVAC controllers, electric vehicle (EV) battery management systems (BMS), solar inverter CAN interfaces, and motor drive position feedback. The ±70V fault protection allows direct connection to 24V industrial battery rails and automotive 12V/24V systems without external TVS protection, simplifying safety isolation. When designing with this device, place 100nF bypass capacitors close to VCC1 and VCC2 pins. Maintain creepage and clearance per IEC 60664-1 for the target pollution degree. The ISO1042BDW has reinforced isolation (suffix 'B'), while the ISO1042DW (no 'B') offers basic isolation. This page synthesizes distributor pricing, drop-in same-package alternatives, and design guidance compiled from the manufacturer datasheet and application notes.