A3P060-2VQ100 - 60K Gate ProASIC3 FPGA | Microchip
N.º da peça: A3P060-2VQ100 ✓ AtivoA3P060-2VQ100 Visão geral
An FPGA is a semiconductor whose digital logic, routing, and I/O behavior can be changed after manufacture through a programmable configuration file. A ProASIC3 FPGA belongs to the broader hierarchy of programmable logic devices, combining a programmable logic array, embedded block RAM, configurable input/output blocks, and flash-based nonvolatile configuration. This combination makes the device useful when a design needs hardware flexibility, short development cycles, or field-updatable logic without replacing a fixed application-specific integrated circuit.
The A3P060 device provides 71 I/Os, approximately 60,000 equivalent gates, 700 logic elements, and an 18 Kb block-RAM resource. Its maximum listed clock frequency of 310 MHz provides a practical performance ceiling for clocked datapaths, control logic, glue logic, and interface bridging. The -2 suffix identifies the speed grade, while VQ100 identifies the 100-pin package. The 14 mm by 14 mm surface-mount package supports compact PCB integration while exposing substantially more I/O than a small FPGA in a lower-pin-count package.
Typical implementations include industrial control and data acquisition, embedded communications, instrumentation, test equipment, and general-purpose digital signal-processing support. The 71 I/Os are useful for parallel sensors, counters, display interfaces, memory interfaces, and communications transceivers, while the block RAM can hold buffers, packet data, sampled waveforms, and intermediate calculations. The exact supported interfaces and I/O standards depend on the selected configuration, supply rails, and board-level design.
Designers should use the Microchip pin description table when assigning every VQ100 ball and should preserve the device's published decoupling and configuration requirements. Clock-sensitive designs also require controlled routing, short ground-return paths, and terminated interfaces. The commercial temperature rating makes the A3P060-2VQ100 most appropriate for indoor commercial or industrial equipment whose internal temperatures remain within the specified range; use an industrial-temperature suffix when wider temperature coverage is required.
This page consolidates the device's programming resources, package details, drop-in family alternatives, comparison data, and practical implementation guidance. It is intended to accelerate component selection while preserving the distinctions between speed grade, temperature grade, package, I/O count, logic capacity, and configuration memory.
Alternativas drop-in para A3P060-2VQ100 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com A3P060-2VQ100 (mesmo formato e footprint) — diferindo em Configuration Memory, Device Type, Logic Elements, Package.
A3P060-2VQ100I
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
A3P060-VQG100
✅ Drop-InConsulte o preço
Ver ficha técnica →A3P060-2VQ100Y
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
A3P060-2VQ100 Classificações máximas e características elétricas
| Device Type | ProASIC3 field-programmable gate array (FPGA) |
| Equivalent Gate Count | Approximately 60,000 gates |
| Logic Elements | 700 logic elements |
| Configurable Logic Blocks | 1,536 CLBs |
| Configuration Memory | 18,432 bits |
| Block RAM | 18 Kb |
| Frequência máxima de clock | 310 MHz |
| Core Supply Voltage | 1.5 V |
| I/O Count | 71 I/Os |
| Input Pin Count | 71 inputs |
| Output Pin Count | 71 outputs |
| Speed Grade | -2 |
| Junction Temperature Range | 0°C to 85°C |
| Encapsulamento | VQ100 100-pin TQFP, 14 mm × 14 mm |
| Terminal Pitch | 0.500 mm |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do A3P060-2VQ100 vq100 100-pin tqfp, 14 mm × 14 mm
Configuração de pinos para A3P060-2VQ100 (pacote vq100 100-pin tqfp, 14 mm × 14 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para A3P060-2VQ100.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
A3P060-2VQ100 é adequado para 6 aplicaçãos: Industrial Control Logic, Data Acquisition Front End, Instrumentation and Test Equipment, Communication Interface Bridging, Embedded Signal Processing, Programmable Embedded Control.
Industrial Control Logic
The A3P060-2VQ100 suits compact machine-control logic that needs 71 parallel I/Os, 700 logic elements, and a listed maximum clock frequency of 310 MHz. It can coordinate limit switches, encoders, counters, actuators, and digital interlocks while retaining nonvolatile flash configuration for field updates. The 100-pin TQFP provides more I/O access than low-pin-count alternatives without moving to a larger package. Commercial designs should maintain the device junction below 85°C; systems with wider environmental exposure should use the industrial-temperature A3P060-2VQ100I. Validate timing at the actual -2 speed grade and confirm each signal's I/O standard against the manufacturer pin table.
Recomendado
Data Acquisition Front End
The A3P060-2VQ100 can act as the digital control layer for multiplexed sensors, counters, and parallel converters. Its 71 I/Os allow acquisition channels, triggers, status signals, and interface data lines to share one programmable device, while 18 Kb of block RAM can buffer sampled data or intermediate results. The approximately 60,000-equivalent-gate and 700-logic-element capacity is sufficient for moderate acquisition control rather than high-throughput DSP. Designers should define timing constraints for trigger latency, use the 310 MHz maximum clock only as a device ceiling, and verify that selected pins support the required electrical standards in the A3P060 datasheet.
Recomendado
Instrumentation and Test Equipment
The A3P060-2VQ100 is appropriate for instrumentation that combines measurement sequencing, display control, status reporting, and programmable logic in one device. Its 700 logic elements and 1,536 configurable logic blocks can implement counters, state machines, timing controls, and interface bridges, while the 71 I/Os simplify connections to sensors, front-panel controls, and test points. The 18 Kb block RAM supports local buffering of configuration or measurement sequences. For portable or enclosure-mounted instruments, calculate the worst-case board and junction temperature because the commercial A3P060-2VQ100 is rated from 0°C to 85°C at the junction.
Recomendado
Communication Interface Bridging
The A3P060-2VQ100 can bridge dissimilar digital interfaces when the design needs programmable protocol handling, byte alignment, and parallel-to-serial data movement. Its 71 I/Os provide enough connections for parallel data buses, control signals, clocks, and transceiver enables, while 18 Kb of block RAM can stage frames or packet fragments. The programmable flash configuration allows interface behavior to be revised more easily than with a fixed logic device. Timing closure remains critical: use the -2 speed-grade limits, constrain interface paths, provide clean clocking, and confirm that every assigned pin supports the selected I/O standard.
Recomendado
Embedded Signal Processing
The A3P060-2VQ100 can implement moderate digital signal-processing functions where 18 Kb of block RAM and a listed 310 MHz maximum clock rate are sufficient. Typical blocks include digital filters, correlators, waveform counters, decimation stages, and custom data-packing logic. The approximately 60,000-equivalent-gate capacity allows control and datapath logic to share one FPGA instead of requiring separate programmable devices. Performance should be evaluated through actual synthesis and timing analysis because the maximum device frequency is not a guarantee for every filter or routing path. Keep block RAM and logic placement deterministic, and test all timing corners for the commercial temperature range.
Recomendado
Programmable Embedded Control
The A3P060-2VQ100 offers a compact way to add reprogrammable behavior to an embedded product. It can coordinate power sequencing, monitor discrete inputs, generate control outputs, and store operational modes in its nonvolatile configuration. Because the device offers 71 I/Os, it can connect directly to sensors, relays, indicators, and peripheral buses without requiring a large pin-count companion. The A3P060-2VQ100 is appropriate for indoor commercial products operating with a junction temperature of 0°C to 85°C. For wider environmental range, select the A3P060-2VQ100I and recheck the complete design for temperature-dependent timing and device qualification.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para A3P060-2VQ100 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | A3P060-2VQ100I | A3P060-VQG100 | A3P060-2VQ100Y |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100 (VQ100) | TQFP-100 (VQ100) - same | TQFP-100 (VQ100) - same | TQFP-100 (VQ100) - same |
| FPGA Family | ProASIC3 | ProASIC3 | ProASIC3 | ProASIC3 |
| Equivalent Gate Count | Approximately 60,000 gates | Approximately 60,000 gates | Approximately 60,000 gates | Approximately 60,000 gates |
| I/O Count | 71 I/Os | 71 I/Os | 71 I/Os | 71 inputs and 71 outputs |
Principais diferenciais
- Commercial-temperature option with a 310 MHz listed maximum clock (vs A3P060-2VQ100I)
- Direct ProASIC3 family continuity for existing designs (vs A3P060-VQG100)
- 71-I/O integration in a 100-pin surface-mount package (vs A3P060-2VQ100Y)
Notas de projeto
Use the manufacturer VQ100 land pattern and pin-description table before laying out the PCB. The package is a 14 mm by 14 mm TQFP with 0.500 mm terminal pitch, so paste volume, footprint dimensions, and assembly clearance should be validated against the current package drawing. Keep configuration and clock pins away from noisy switching nodes, provide a continuous ground reference, and route sensitive inputs away from the 1.5 V core supply return path.
Decouple the 1.5 V core supply according to the ProASIC3 family guidance and place the required capacitors close to their assigned package pins. Separate core and I/O supply paths where the design permits, minimize loop area, and verify every rail against the selected A3P060 configuration. Power sequencing and signal-state requirements during configuration must also be checked because a valid power rail alone does not guarantee that every configuration pin starts in the required state.
The 310 MHz figure is a device-family maximum, not a guaranteed operating rate for every routed design. Constrain clocks and high-speed interfaces, use short point-to-point routes where appropriate, provide continuous reference planes, and avoid unnecessary stubs. Add source-series termination only when the selected I/O standard and edge rate require it. Complete timing analysis for the -2 speed grade over the required commercial temperature range.
Do not treat every A3P060 VQ100 suffix as automatically interchangeable. The A3P060-2VQ100I changes temperature coverage, while A3P060-VQG100 and A3P060-2VQ100Y use different suffix conventions. Confirm the complete ordering code, speed grade, temperature grade, package orientation, and pin description before replacing the part. Also distinguish the 71 total I/O listing from descriptions that separately list 71 inputs and 71 outputs.
Informações de conformidade
No explicit environmental or automotive qualification statements appear in the product and distributor records. Compliance status must be confirmed using the manufacturer declaration for the exact ordering code.