A3P060-2VQ100 - 60K Gate ProASIC3 FPGA | Microchip
料号: A3P060-2VQ100 ✓ 量产中A3P060-2VQ100 概述
An FPGA is a semiconductor whose digital logic, routing, and I/O behavior can be changed after manufacture through a programmable configuration file. A ProASIC3 FPGA belongs to the broader hierarchy of programmable logic devices, combining a programmable logic array, embedded block RAM, configurable input/output blocks, and flash-based nonvolatile configuration. This combination makes the device useful when a design needs hardware flexibility, short development cycles, or field-updatable logic without replacing a fixed application-specific integrated circuit.
The A3P060 device provides 71 I/Os, approximately 60,000 equivalent gates, 700 logic elements, and an 18 Kb block-RAM resource. Its maximum listed clock frequency of 310 MHz provides a practical performance ceiling for clocked datapaths, control logic, glue logic, and interface bridging. The -2 suffix identifies the speed grade, while VQ100 identifies the 100-pin package. The 14 mm by 14 mm surface-mount package supports compact PCB integration while exposing substantially more I/O than a small FPGA in a lower-pin-count package.
Typical implementations include industrial control and data acquisition, embedded communications, instrumentation, test equipment, and general-purpose digital signal-processing support. The 71 I/Os are useful for parallel sensors, counters, display interfaces, memory interfaces, and communications transceivers, while the block RAM can hold buffers, packet data, sampled waveforms, and intermediate calculations. The exact supported interfaces and I/O standards depend on the selected configuration, supply rails, and board-level design.
Designers should use the Microchip pin description table when assigning every VQ100 ball and should preserve the device's published decoupling and configuration requirements. Clock-sensitive designs also require controlled routing, short ground-return paths, and terminated interfaces. The commercial temperature rating makes the A3P060-2VQ100 most appropriate for indoor commercial or industrial equipment whose internal temperatures remain within the specified range; use an industrial-temperature suffix when wider temperature coverage is required.
This page consolidates the device's programming resources, package details, drop-in family alternatives, comparison data, and practical implementation guidance. It is intended to accelerate component selection while preserving the distinctions between speed grade, temperature grade, package, I/O count, logic capacity, and configuration memory.
直接替换替代料: A3P060-2VQ100 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: A3P060-2VQ100 (相同外形与封装尺寸) ——差异在于 Configuration Memory, Device Type, Logic Elements, Package.
A3P060-2VQ100I
✅ 直接替换📋 参考替代料(不在目录中)
A3P060-VQG100
✅ 直接替换联系询价
查看数据手册 →A3P060-2VQ100Y
✅ 直接替换📋 参考替代料(不在目录中)
A3P060-2VQ100 最大额定值与电气特性
| Device Type | ProASIC3 field-programmable gate array (FPGA) |
| Equivalent Gate Count | Approximately 60,000 gates |
| Logic Elements | 700 logic elements |
| Configurable Logic Blocks | 1,536 CLBs |
| Configuration Memory | 18,432 bits |
| Block RAM | 18 Kb |
| 最大时钟频率 | 310 MHz |
| Core Supply Voltage | 1.5 V |
| I/O Count | 71 I/Os |
| Input Pin Count | 71 inputs |
| Output Pin Count | 71 outputs |
| Speed Grade | -2 |
| Junction Temperature Range | 0°C to 85°C |
| 封装 | VQ100 100-pin TQFP, 14 mm × 14 mm |
| Terminal Pitch | 0.500 mm |
| 安装类型 | Surface mount |
A3P060-2VQ100 vq100 100-pin tqfp, 14 mm × 14 mm 引脚配置指南
A3P060-2VQ100(vq100 100-pin tqfp, 14 mm × 14 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: A3P060-2VQ100.
请参阅 数据手册 以查看完整引脚配置。
典型应用
A3P060-2VQ100 适用于 6 应用s: Industrial Control Logic, Data Acquisition Front End, Instrumentation and Test Equipment, Communication Interface Bridging, Embedded Signal Processing, Programmable Embedded Control.
Industrial Control Logic
The A3P060-2VQ100 suits compact machine-control logic that needs 71 parallel I/Os, 700 logic elements, and a listed maximum clock frequency of 310 MHz. It can coordinate limit switches, encoders, counters, actuators, and digital interlocks while retaining nonvolatile flash configuration for field updates. The 100-pin TQFP provides more I/O access than low-pin-count alternatives without moving to a larger package. Commercial designs should maintain the device junction below 85°C; systems with wider environmental exposure should use the industrial-temperature A3P060-2VQ100I. Validate timing at the actual -2 speed grade and confirm each signal's I/O standard against the manufacturer pin table.
推荐
Data Acquisition Front End
The A3P060-2VQ100 can act as the digital control layer for multiplexed sensors, counters, and parallel converters. Its 71 I/Os allow acquisition channels, triggers, status signals, and interface data lines to share one programmable device, while 18 Kb of block RAM can buffer sampled data or intermediate results. The approximately 60,000-equivalent-gate and 700-logic-element capacity is sufficient for moderate acquisition control rather than high-throughput DSP. Designers should define timing constraints for trigger latency, use the 310 MHz maximum clock only as a device ceiling, and verify that selected pins support the required electrical standards in the A3P060 datasheet.
推荐
Instrumentation and Test Equipment
The A3P060-2VQ100 is appropriate for instrumentation that combines measurement sequencing, display control, status reporting, and programmable logic in one device. Its 700 logic elements and 1,536 configurable logic blocks can implement counters, state machines, timing controls, and interface bridges, while the 71 I/Os simplify connections to sensors, front-panel controls, and test points. The 18 Kb block RAM supports local buffering of configuration or measurement sequences. For portable or enclosure-mounted instruments, calculate the worst-case board and junction temperature because the commercial A3P060-2VQ100 is rated from 0°C to 85°C at the junction.
推荐
Communication Interface Bridging
The A3P060-2VQ100 can bridge dissimilar digital interfaces when the design needs programmable protocol handling, byte alignment, and parallel-to-serial data movement. Its 71 I/Os provide enough connections for parallel data buses, control signals, clocks, and transceiver enables, while 18 Kb of block RAM can stage frames or packet fragments. The programmable flash configuration allows interface behavior to be revised more easily than with a fixed logic device. Timing closure remains critical: use the -2 speed-grade limits, constrain interface paths, provide clean clocking, and confirm that every assigned pin supports the selected I/O standard.
推荐
Embedded Signal Processing
The A3P060-2VQ100 can implement moderate digital signal-processing functions where 18 Kb of block RAM and a listed 310 MHz maximum clock rate are sufficient. Typical blocks include digital filters, correlators, waveform counters, decimation stages, and custom data-packing logic. The approximately 60,000-equivalent-gate capacity allows control and datapath logic to share one FPGA instead of requiring separate programmable devices. Performance should be evaluated through actual synthesis and timing analysis because the maximum device frequency is not a guarantee for every filter or routing path. Keep block RAM and logic placement deterministic, and test all timing corners for the commercial temperature range.
推荐
Programmable Embedded Control
The A3P060-2VQ100 offers a compact way to add reprogrammable behavior to an embedded product. It can coordinate power sequencing, monitor discrete inputs, generate control outputs, and store operational modes in its nonvolatile configuration. Because the device offers 71 I/Os, it can connect directly to sensors, relays, indicators, and peripheral buses without requiring a large pin-count companion. The A3P060-2VQ100 is appropriate for indoor commercial products operating with a junction temperature of 0°C to 85°C. For wider environmental range, select the A3P060-2VQ100I and recheck the complete design for temperature-dependent timing and device qualification.
推荐
推荐产品汇总
工程参考数据: A3P060-2VQ100 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | A3P060-2VQ100I | A3P060-VQG100 | A3P060-2VQ100Y |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100 (VQ100) | TQFP-100 (VQ100) - same | TQFP-100 (VQ100) - same | TQFP-100 (VQ100) - same |
| FPGA Family | ProASIC3 | ProASIC3 | ProASIC3 | ProASIC3 |
| Equivalent Gate Count | Approximately 60,000 gates | Approximately 60,000 gates | Approximately 60,000 gates | Approximately 60,000 gates |
| I/O Count | 71 I/Os | 71 I/Os | 71 I/Os | 71 inputs and 71 outputs |
关键差异点
- Commercial-temperature option with a 310 MHz listed maximum clock (对比 A3P060-2VQ100I)
- Direct ProASIC3 family continuity for existing designs (对比 A3P060-VQG100)
- 71-I/O integration in a 100-pin surface-mount package (对比 A3P060-2VQ100Y)
设计说明
Use the manufacturer VQ100 land pattern and pin-description table before laying out the PCB. The package is a 14 mm by 14 mm TQFP with 0.500 mm terminal pitch, so paste volume, footprint dimensions, and assembly clearance should be validated against the current package drawing. Keep configuration and clock pins away from noisy switching nodes, provide a continuous ground reference, and route sensitive inputs away from the 1.5 V core supply return path.
Decouple the 1.5 V core supply according to the ProASIC3 family guidance and place the required capacitors close to their assigned package pins. Separate core and I/O supply paths where the design permits, minimize loop area, and verify every rail against the selected A3P060 configuration. Power sequencing and signal-state requirements during configuration must also be checked because a valid power rail alone does not guarantee that every configuration pin starts in the required state.
The 310 MHz figure is a device-family maximum, not a guaranteed operating rate for every routed design. Constrain clocks and high-speed interfaces, use short point-to-point routes where appropriate, provide continuous reference planes, and avoid unnecessary stubs. Add source-series termination only when the selected I/O standard and edge rate require it. Complete timing analysis for the -2 speed grade over the required commercial temperature range.
Do not treat every A3P060 VQ100 suffix as automatically interchangeable. The A3P060-2VQ100I changes temperature coverage, while A3P060-VQG100 and A3P060-2VQ100Y use different suffix conventions. Confirm the complete ordering code, speed grade, temperature grade, package orientation, and pin description before replacing the part. Also distinguish the 71 total I/O listing from descriptions that separately list 71 inputs and 71 outputs.
合规信息
No explicit environmental or automotive qualification statements appear in the product and distributor records. Compliance status must be confirmed using the manufacturer declaration for the exact ordering code.