AD623ARMZ - 3V-12V Rail-to-Rail Instrumentation Amp | Analog Devices
N.º da peça: AD623ARMZ ✓ AtivoAD623ARMZ Visão geral
An instrumentation amplifier is a differential-input amplifier built around an op-amp core, finished with a matched resistor network. The category hierarchy runs instrumentation amplifier -> differential amplifier -> op-amp stage -> analog signal conditioning IC. Instead of a conventional difference amplifier, an in-amp uses four matched resistors to reject common-mode voltage and convert a small differential sensor signal into a single-ended ground-referenced output. Because the resistors are on the same die and laser-trimmed, the AD623 holds high common-mode rejection even with long sensor wiring.
Key features of the AD623ARMZ include true rail-to-rail output swing, single-supply operation down to 3 V, gain set by one external resistor (no dual-resistor divider), an 8-lead industry-standard pinout that is pin compatible with the AD620/AD621/AD823 family, and a REF pin that allows output offsetting and direct connection to an ADC input. Input offset voltage and CMRR are specified at both G = 1 and higher gains, letting designers size the error budget before layout.
Technically the AD623 is a classic three-op-amp topology: an input stage with high-impedance differential inputs, a differential-to-single-ended middle stage, and an output buffer that drives the load to ground. Because the output buffer swings to both rails, the part can drive the ADC input directly without a coupling capacitor. The 800 kHz unity-gain bandwidth means the closed-loop bandwidth falls roughly with gain, so at G = 100 the usable bandwidth drops to about 8 kHz, which sets the maximum sensor update rate in bridge and thermocouple designs.
Typical applications include load-cell and pressure bridge front ends, medical and industrial sensor signal conditioning, current-shunt measurement in power conversion, and battery or process monitoring on 3.3 V and 5 V rails. For low-voltage systems the 3 V minimum supply is the key advantage over the classic AD620, which expects a wider supply span.
When designing with the AD623ARMZ, keep the gain resistor close to the RG pin and place the REF pin bypass network at the same ground reference as the sensor return. Provide an RC filter ahead of the inputs if long cables pick up noise, because common-mode rejection degrades with imbalance above roughly 1 kHz. Note that gain error and CMRR are specified with a common-mode range, so verify the sensor's common-mode voltage stays inside that window.
Alternativas drop-in para AD623ARMZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com AD623ARMZ (mesmo formato e footprint) — diferindo em Output Swing, Package, Pin Configuration, Product Type, REACH Status.
AD823ARMZ
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AD621ARMZ
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AD620ARMZ
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AD8221ARMZ
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AD8229ARMZ
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AD623ARMZ Classificações máximas e características elétricas
| Product Type | Single-supply instrumentation amplifier (IN-AMP) |
| Number of Channels | 1 channel |
| Supply Voltage Range | 3 V to 12 V (2.7 V to 12 V per manufacturer product page) |
| Output Swing | Rail-to-rail output |
| Gain Range | 1 to 1000, set by a single external resistor |
| 3 dB Bandwidth (G = 1) | 800 kHz |
| Slew Rate | 300 mV/us |
| Encapsulamento | 8-lead MSOP (RM-8), surface mount |
| Pin Configuration | 8-lead industry-standard in-amp pinout |
| REF Pin Function | Output reference / offset input |
| MSL | MSL 1 (unlimited floor life) |
| RoHS Compliance | RoHS3 compliant |
| REACH Status | Unaffected |
| Faixa de temperatura de operação | -40 C to +85 C |
Configuração de pinos do AD623ARMZ
| Pino 1 | OUTPUT+ — Non-inverting output |
| Pino 2 | -INPUT — Inverting input |
| Pino 3 | +INPUT — Non-inverting input |
| Pino 4 | -Vs — Negative supply (ground on single-supply operation) |
| Pino 5 | REF — Output reference / offset input |
| Pino 6 | OUTPUT- — Inverting output |
| Pino 7 | +Vs — Positive supply |
| Pino 8 | RG — Gain-set resistor connection |
Aplicações típicas
AD623ARMZ é adequado para 6 aplicaçãos: Load-Cell and Bridge Sensor Front End, Current Shunt Measurement in Power Conversion, Medical and Biosignal Sensor Conditioning, Thermocouple and RTD Cold-Junction Conditioning, Industrial Process Control and PLC Analog Input, Battery Monitoring and Energy Metering.
Load-Cell and Bridge Sensor Front End
The AD623ARMZ suits load cells and resistive bridge pressure sensors because its matched internal resistor network rejects the large excitation common-mode voltage while the 800 kHz unity-gain bandwidth lets the amplifier settle quickly after a channel change. Gain is set by a single resistor, so a 1 mV/V bridge output becomes a usable level with one component. Place the gain resistor at the RG pin, tie REF to the sensor return ground, and note that common-mode rejection degrades above roughly 1 kHz, so a differential RC filter ahead of the inputs improves noise immunity.
Recomendado
Current Shunt Measurement in Power Conversion
In a battery charger or DC-DC converter, the AD623ARMZ measures the voltage across a low-ohm shunt with a common-mode voltage equal to the bus rail, which is exactly where a good CMRR matters. Its rail-to-rail output lets the amplifier run from the same 3.3 V or 5 V rail it is monitoring and drive the controller ADC directly without a level shift. Because the gain resistor is a single component, a software-programmable measurement chain is easy to implement with a switched resistor bank.
Recomendado
Medical and Biosignal Sensor Conditioning
For ECG, EMG and body-impedance front ends, the AD623ARMZ provides the differential-to-single-ended conversion that a bipolar biopotential signal requires, while its rail-to-rail output on a 3 V supply maximises the usable ADC input window in compact patient monitors. The 300 mV/us slew rate handles electrode motion artefact without saturating, and the 8-lead MSOP footprint keeps the analog section small next to the MCU. Keep the REF pin at the analog ground of the electrode amplifier and shield the input routing to avoid mains pickup.
Recomendado
Thermocouple and RTD Cold-Junction Conditioning
The AD623ARMZ accepts the microvolt-to-millivolt differential output of a thermocouple or RTD bridge and amplifies it to a level a low-resolution ADC can use, all from a 3 V to 12 V supply that matches a small sensor node. Its fast unity-gain bandwidth of 800 kHz means the amplifier is not the limiting element in a slowly sampled temperature loop, and the wide input common-mode range keeps the part usable with typical 2-wire and 3-wire sensor wiring. Add an input filter to reject 50/60 Hz pickup while preserving the differential balance.
Recomendado
Industrial Process Control and PLC Analog Input
In a PLC or industrial sensor gateway, the AD623ARMZ conditions a 4-20 mA-derived or differential process signal before conversion, converting a bipolar input into a single-ended 0 V reference output suitable for a 12-bit or 16-bit ADC. Running from 3 V to 12 V covers both 24 V bus designs with local regulation and low-voltage sensor hubs, and the rail-to-rail output maximises the signal span into the converter. Place the gain resistor and REF bypass capacitor adjacent to the package, and route the sensor return as a differential pair back to the inputs.
Recomendado
Battery Monitoring and Energy Metering
Battery management systems use the AD623ARMZ to sense cell voltage and shunt current on a common 3.3 V rail, where the rail-to-rail output lets the measurement reach the full ADC input range without wasting headroom. The 800 kHz bandwidth supports the fast acquisition needed for state-of-charge algorithms, and the single external gain resistor makes it easy to change measurement ranges between different cell counts. Keep the shunt Kelvin connections separate from the power path so IR drop does not enter the differential signal.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para AD623ARMZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | AD823ARMZ | AD621ARMZ | AD620ARMZ | AD8221ARMZ | AD8229ARMZ |
|---|---|---|---|---|---|---|
| Package | MSOP-8 (RM-8) | MSOP-8 (RM-8) - same | MSOP-8 (RM-8) - same | MSOP-8 (RM-8) - same | MSOP-8 (RM-8) - same | MSOP-8 (RM-8) - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Gain Range | 1 to 1000, single gain resistor | 1 to 1000, single gain resistor | 1 to 1000, single gain resistor | 1 to 1000, single gain resistor | 1 to 1000, single gain resistor | 1 to 1000, single gain resistor |
| REF Pin | Yes, output reference / offset | Yes | Yes | Yes | Yes | Yes |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
Principais diferenciais
- Operates from a 3 V supply with a rail-to-rail output stage (vs AD620ARMZ)
- Much faster settling for multiplexed sensor channels (vs AD8229ARMZ)
- Single-resistor gain programming simplifies the BOM (vs AD621ARMZ)
- Higher speed than the AD823 family member in the same footprint (vs AD823ARMZ)
Notas de projeto
The most common design error is assuming the AD623 can accept any common-mode voltage because it has a rail-to-rail output. The rail-to-rail specification applies to the output stage only; the input common-mode range is finite and is specified in the AD623 data sheet. Always check the sensor's common-mode voltage against that range, especially on 3.3 V supplies where the window is narrow. A second common mistake is leaving the REF pin floating, which lets noise and offset dominate the output - tie REF to the analog ground or drive it deliberately.
Place the gain-set resistor directly at the RG pin with the shortest possible trace, because parasitic capacitance at RG adds phase shift and can reduce stability at high gain. Keep the two input nets as a tight differential pair routed over a continuous ground plane, and return the sensor shield to the same reference node as REF. Place the input RC filter components symmetrically so the differential balance, and therefore the common-mode rejection at frequencies above roughly 1 kHz, is preserved.
Estimated: the AD623ARMZ draws roughly 0.6 mA per channel from the supply, so at a 3.3 V rail the dissipation is on the order of 2 mW - heat is rarely a concern in the MSOP-8 package. The real supply consideration is headroom: because the output swings to the rails, the usable output window on a 3.3 V supply is only about 0 V to 3.3 V before output saturation, so design the gain so the worst-case differential input does not push the output into the rails.
For long sensor cables, add a matched RC filter at each input (for example 100 Ohm plus 10 nF) to limit differential-mode and common-mode pickup before it is amplified. Keep the added capacitance roughly equal on both inputs, since unmatched filtering converts common-mode noise into differential error that no amount of on-chip CMRR can remove. Verify the resulting bandwidth against the 800 kHz unity-gain figure and against the expected 50/60 Hz rejection of your amplifier.
Informações de conformidade
RoHS3 compliant and REACH unaffected per the part listing; MSL 1 (unlimited floor life). AEC-Q100 qualification is not indicated for the standard commercial ordering code - confirm with the manufacturer for automotive programs.