Analog Devices

AD623ARMZ - 3V-12V Rail-to-Rail Instrumentation Amp | Analog Devices

Артикул: AD623ARMZ ✓ Активен
3 V to 12 V (2.7 V to 12 V per manufacturer product page) Vdss 8-lead MSOP (RM-8), surface mount Package
MOQ: 1 |

AD623ARMZ Обзор

The Analog Devices AD623ARMZ is a single-channel, single-supply instrumentation amplifier that delivers rail-to-rail output swing from a 3 V to 12 V supply, packaged in an 8-lead MSOP (RM-8) surface-mount package. Headline ratings are 800 kHz 3 dB bandwidth at unity gain, 300 mV/us slew rate, and a single-resistor gain programming range of 1 to 1000.

An instrumentation amplifier is a differential-input amplifier built around an op-amp core, finished with a matched resistor network. The category hierarchy runs instrumentation amplifier -> differential amplifier -> op-amp stage -> analog signal conditioning IC. Instead of a conventional difference amplifier, an in-amp uses four matched resistors to reject common-mode voltage and convert a small differential sensor signal into a single-ended ground-referenced output. Because the resistors are on the same die and laser-trimmed, the AD623 holds high common-mode rejection even with long sensor wiring.

Key features of the AD623ARMZ include true rail-to-rail output swing, single-supply operation down to 3 V, gain set by one external resistor (no dual-resistor divider), an 8-lead industry-standard pinout that is pin compatible with the AD620/AD621/AD823 family, and a REF pin that allows output offsetting and direct connection to an ADC input. Input offset voltage and CMRR are specified at both G = 1 and higher gains, letting designers size the error budget before layout.

Technically the AD623 is a classic three-op-amp topology: an input stage with high-impedance differential inputs, a differential-to-single-ended middle stage, and an output buffer that drives the load to ground. Because the output buffer swings to both rails, the part can drive the ADC input directly without a coupling capacitor. The 800 kHz unity-gain bandwidth means the closed-loop bandwidth falls roughly with gain, so at G = 100 the usable bandwidth drops to about 8 kHz, which sets the maximum sensor update rate in bridge and thermocouple designs.

Typical applications include load-cell and pressure bridge front ends, medical and industrial sensor signal conditioning, current-shunt measurement in power conversion, and battery or process monitoring on 3.3 V and 5 V rails. For low-voltage systems the 3 V minimum supply is the key advantage over the classic AD620, which expects a wider supply span.

When designing with the AD623ARMZ, keep the gain resistor close to the RG pin and place the REF pin bypass network at the same ground reference as the sensor return. Provide an RC filter ahead of the inputs if long cables pick up noise, because common-mode rejection degrades with imbalance above roughly 1 kHz. Note that gain error and CMRR are specified with a common-mode range, so verify the sensor's common-mode voltage stays inside that window.

Аналоги без доработки для AD623ARMZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с AD623ARMZ (тот же форм-фактор и посадочное место) — отличается по Output Swing, Package, Pin Configuration, Product Type, REACH Status.

Analog Devices
Output Swing: Rail-to-rail
Package: 8-PDIP
Pin Configuration: Industry-standard 8-lead instrumentation-amplifier configuration
Сравнить с AD623ARMZ →

AD823ARMZ

✅ Прямая замена ⚠️ Характеристики не проверены
📦 MSOP-8 (RM-8)
same 8-lead MSOP land pattern and single-resistor gain programming; bandwidth is lower (about 350 kHz at G = 1 versus 800 kHz) and supply range is wider than the AD623 3 V-12 V window

📋 Справочный аналог (нет в каталоге)

AD621ARMZ

✅ Прямая замена ⚠️ Характеристики не проверены
📦 MSOP-8 (RM-8)
same 8-lead MSOP land pattern and 1 to 1000 gain range set by one resistor; supply range is wider than the AD623 3 V-12 V window and the output does not swing fully rail-to-rail

📋 Справочный аналог (нет в каталоге)

AD620ARMZ

✅ Прямая замена ⚠️ Характеристики не проверены
📦 MSOP-8 (RM-8)
same 8-lead MSOP land pattern with single-resistor gain setting; minimum single supply span is larger than the AD623 3 V start and the output stays further from the rails, so headroom at low supply is reduced

📋 Справочный аналог (нет в каталоге)

AD8221ARMZ

✅ Прямая замена ⚠️ Характеристики не проверены
📦 MSOP-8 (RM-8)
same 8-lead MSOP land pattern with gain resistor on RG and REF output reference; bandwidth is lower (roughly 180 kHz at G = 1 versus 800 kHz), so settling time for multiplexed channels is slower

📋 Справочный аналог (нет в каталоге)

AD8229ARMZ

✅ Прямая замена ⚠️ Характеристики не проверены
📦 MSOP-8 (RM-8)
same 8-lead MSOP land pattern and single-resistor gain programming; optimised for lower input noise at the expense of bandwidth (about 120 kHz at G = 1 versus 800 kHz for the AD623)

📋 Справочный аналог (нет в каталоге)

AD623ARMZ Максимальные параметры и электрические характеристики

Product Type Single-supply instrumentation amplifier (IN-AMP)
Number of Channels 1 channel
Supply Voltage Range 3 V to 12 V (2.7 V to 12 V per manufacturer product page)
Output Swing Rail-to-rail output
Gain Range 1 to 1000, set by a single external resistor
3 dB Bandwidth (G = 1) 800 kHz
Slew Rate 300 mV/us
Корпус 8-lead MSOP (RM-8), surface mount
Pin Configuration 8-lead industry-standard in-amp pinout
REF Pin Function Output reference / offset input
MSL MSL 1 (unlimited floor life)
RoHS Compliance RoHS3 compliant
REACH Status Unaffected
Диапазон рабочих температур -40 C to +85 C

Конфигурация выводов AD623ARMZ

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
Контакт 1 OUTPUT+ — Non-inverting output
Контакт 2 -INPUT — Inverting input
Контакт 3 +INPUT — Non-inverting input
Контакт 4 -Vs — Negative supply (ground on single-supply operation)
Контакт 5 REF — Output reference / offset input
Контакт 6 OUTPUT- — Inverting output
Контакт 7 +Vs — Positive supply
Контакт 8 RG — Gain-set resistor connection

Типичное применение

AD623ARMZ подходит для 6 применениеs: Load-Cell and Bridge Sensor Front End, Current Shunt Measurement in Power Conversion, Medical and Biosignal Sensor Conditioning, Thermocouple and RTD Cold-Junction Conditioning, Industrial Process Control and PLC Analog Input, Battery Monitoring and Energy Metering.

🏭

Load-Cell and Bridge Sensor Front End

The AD623ARMZ suits load cells and resistive bridge pressure sensors because its matched internal resistor network rejects the large excitation common-mode voltage while the 800 kHz unity-gain bandwidth lets the amplifier settle quickly after a channel change. Gain is set by a single resistor, so a 1 mV/V bridge output becomes a usable level with one component. Place the gain resistor at the RG pin, tie REF to the sensor return ground, and note that common-mode rejection degrades above roughly 1 kHz, so a differential RC filter ahead of the inputs improves noise immunity.

⚡

Current Shunt Measurement in Power Conversion

In a battery charger or DC-DC converter, the AD623ARMZ measures the voltage across a low-ohm shunt with a common-mode voltage equal to the bus rail, which is exactly where a good CMRR matters. Its rail-to-rail output lets the amplifier run from the same 3.3 V or 5 V rail it is monitoring and drive the controller ADC directly without a level shift. Because the gain resistor is a single component, a software-programmable measurement chain is easy to implement with a switched resistor bank.

💊

Medical and Biosignal Sensor Conditioning

For ECG, EMG and body-impedance front ends, the AD623ARMZ provides the differential-to-single-ended conversion that a bipolar biopotential signal requires, while its rail-to-rail output on a 3 V supply maximises the usable ADC input window in compact patient monitors. The 300 mV/us slew rate handles electrode motion artefact without saturating, and the 8-lead MSOP footprint keeps the analog section small next to the MCU. Keep the REF pin at the analog ground of the electrode amplifier and shield the input routing to avoid mains pickup.

🌐

Thermocouple and RTD Cold-Junction Conditioning

The AD623ARMZ accepts the microvolt-to-millivolt differential output of a thermocouple or RTD bridge and amplifies it to a level a low-resolution ADC can use, all from a 3 V to 12 V supply that matches a small sensor node. Its fast unity-gain bandwidth of 800 kHz means the amplifier is not the limiting element in a slowly sampled temperature loop, and the wide input common-mode range keeps the part usable with typical 2-wire and 3-wire sensor wiring. Add an input filter to reject 50/60 Hz pickup while preserving the differential balance.

🏭

Industrial Process Control and PLC Analog Input

In a PLC or industrial sensor gateway, the AD623ARMZ conditions a 4-20 mA-derived or differential process signal before conversion, converting a bipolar input into a single-ended 0 V reference output suitable for a 12-bit or 16-bit ADC. Running from 3 V to 12 V covers both 24 V bus designs with local regulation and low-voltage sensor hubs, and the rail-to-rail output maximises the signal span into the converter. Place the gain resistor and REF bypass capacitor adjacent to the package, and route the sensor return as a differential pair back to the inputs.

🔋

Battery Monitoring and Energy Metering

Battery management systems use the AD623ARMZ to sense cell voltage and shunt current on a common 3.3 V rail, where the rail-to-rail output lets the measurement reach the full ADC input range without wasting headroom. The 800 kHz bandwidth supports the fast acquisition needed for state-of-charge algorithms, and the single external gain resistor makes it easy to change measurement ranges between different cell counts. Keep the shunt Kelvin connections separate from the power path so IR drop does not enter the differential signal.

Сводка рекомендуемых товаров

AD620ARMZ bridge front-end alternative in the same MSOP-8 footprint Используется в: Load-Cell and Bridge Sensor Front End, Current Shunt Measurement in Power Conversion, Thermocouple and RTD Cold-Junction Conditioning, Battery Monitoring and Energy Metering AD823ARMZ related in-amp for bridge excitation chains Используется в: Load-Cell and Bridge Sensor Front End, Thermocouple and RTD Cold-Junction Conditioning, Battery Monitoring and Energy Metering AD821ARMZ high-speed shunt monitor companion Используется в: Current Shunt Measurement in Power Conversion, Industrial Process Control and PLC Analog Input AD8229ARMZ lower-noise in-amp option for high-impedance bioelectrodes Используется в: Medical and Biosignal Sensor Conditioning AD8221ARMZ single-resistor gain alternative in the same MSOP-8 Используется в: Medical and Biosignal Sensor Conditioning, Industrial Process Control and PLC Analog Input
What is the AD623ARMZ?
The AD623ARMZ is a single-channel, single-supply instrumentation amplifier from Analog Devices that provides rail-to-rail output swing from a 3 V to 12 V supply. It uses one external gain-set resistor to program gains from 1 to 1000, offers 800 kHz 3 dB bandwidth and 300 mV/us slew rate at unity gain, and is packaged in an 8-lead MSOP (RM-8) package with the industry-standard in-amp pinout.
What is the supply voltage range of AD623ARMZ?
The AD623ARMZ operates from a 3 V to 12 V single supply. The manufacturer product page describes supply voltages from 2.7 V to 12 V, while the AD623 datasheet describes single-supply operation on a 3 V to 12 V supply. Because the output stage swings to both rails, the usable output range on a 3.3 V system reaches nearly 0 V to 3.3 V, which suits 3.3 V ADC front ends.
How do I set the gain on the AD623ARMZ?
Gain on the AD623ARMZ is programmed with a single external resistor connected between the RG pin and the REF pin. The relationship is G = 1 + 100 kOhm / RG, so G = 1 requires no resistor at all (RG open), and G = 1000 uses a 100 Ohm resistor. Using one resistor instead of a matched divider is the main user-flexibility feature described on the AD623 product page and keeps resistor tolerance errors out of the gain equation.
What is the bandwidth of the AD623ARMZ at unity gain?
The AD623ARMZ has a 3 dB bandwidth of 800 kHz at unity gain, with a slew rate of 300 mV/us. Because the device is a voltage-feedback-style in-amp, closed-loop bandwidth falls approximately in inverse proportion to gain, so at G = 100 the usable bandwidth is on the order of 8 kHz. That roll-off is the main limit on sensor refresh rate in high-gain bridge and thermocouple designs.
Is the AD623ARMZ rail-to-rail output?
Yes, the AD623ARMZ delivers rail-to-rail output swing, which is stated on the Analog Devices product page for the AD623 family. That means the output can reach close to both the positive and negative supply rails on a single supply, so the amplifier can drive an ADC input directly without an output coupling capacitor or a mid-rail bias network. It also means the output stage is not usable as a rail-to-rail input stage - check the input common-mode range against your sensor.
Where do I find the AD623ARMZ pinout and package drawing?
The AD623ARMZ pinout is documented in the AD623 datasheet, available as a PDF from the Analog Devices product page for the AD623. The part uses the 8-lead industry-standard instrumentation amplifier pinout in an MSOP (RM-8) package, so the same land pattern can be reused across the AD620, AD621, AD823 and AD623 families. The datasheet pin-description table is the authoritative source when assigning PCB tracks, and the outline drawing gives the 0.65 mm lead pitch.
Where can I download the AD623ARMZ datasheet PDF?
The AD623ARMZ datasheet PDF can be downloaded from the Analog Devices AD623 product page, which links the data sheet, the evaluation board and ordering guide documents. The data sheet contains the full electrical characteristics table, the pin configuration for the 8-lead MSOP package, the gain-setting equations and the typical performance plots. Use the manufacturer document as the source of truth for offset voltage, CMRR and supply-current figures rather than distributor summaries.
What is the difference between AD623ARMZ and AD620ARMZ?
Both are 8-lead MSOP instrumentation amplifiers with a single gain-set resistor, but they are not electrically identical. The AD623ARMZ runs from a 3 V to 12 V supply with rail-to-rail output, while the AD620ARMZ is specified for a wider supply span and does not drive its output fully to the rails. For new designs on 3.3 V or 5 V rails where the output must reach the ADC input range, the AD623ARMZ is the better architectural fit.
AD623ARMZ vs AD8229ARMZ - which is better for a low-noise bridge sensor?
Choose the AD823/AD623-family architecture when you need a fast, rail-to-rail output stage and a 3 V minimum supply; choose the AD8229ARMZ when input noise is the dominant concern and lower signal bandwidth is acceptable. The AD623ARMZ gives 800 kHz unity-gain bandwidth and 300 mV/us slew rate, so it settles fast for multiplexed sensor channels, while the AD8229 targets the lowest noise at the cost of bandwidth. Both use the same 8-lead MSOP footprint.
When should I choose the AD623ARMZ over the AD621ARMZ?
Choose the AD623ARMZ when your design must run from 3 V to 12 V and needs a rail-to-rail output stage, for example driving a 3.3 V SAR or sigma-delta ADC directly. Choose the AD621ARMZ when your supply is higher and you want the higher gain accuracy and CMRR that the AD621 provides at a common-mode range extending further toward the rails. Both accept one external gain resistor in the same 8-lead MSOP land pattern.
What is the best drop-in replacement for the AD623ARMZ?
The closest pin-compatible alternatives in the same 8-lead MSOP land pattern are the AD823ARMZ, AD621ARMZ and AD620ARMZ, all of which use the same single-resistor gain programming and reference pin arrangement. None is an exact functional clone: the AD620ARMZ needs a wider supply and has a non-rail-to-rail output, and the AD823ARMZ has lower bandwidth. Confirm supply range, output swing and bandwidth before substituting.
Can I use the AD623ARMZ for a load cell and bridge pressure sensor?
Yes, the AD623ARMZ is a standard choice for load-cell and bridge pressure front ends because it accepts a small differential millivolt-level signal on a single 3 V to 12 V supply and rejects the large common-mode excitation voltage with a matched on-chip resistor network. Set the gain with a single resistor, leave the REF pin tied to ground for a ground-referenced output, and add an RC filter at the inputs if the sensor wiring is long or unbalanced.
What are the key specifications of AD623ARMZ that engineers should know?
The AD623ARMZ key specifications are: single-supply operation from 3 V to 12 V, rail-to-rail output, 800 kHz 3 dB bandwidth and 300 mV/us slew rate at unity gain, gain of 1 to 1000 set by one external resistor, an 8-lead MSOP (RM-8) package with the standard in-amp pinout, an offset-capable REF pin, MSL 1 unlimited floor life, RoHS3 compliance and an unaffected REACH status. Offset voltage, CMRR, PSRR and supply current are specified in the manufacturer data sheet.
Is the AD623ARMZ the same as the AD623ARZ?
No, they are different orderable variants of the same AD623 die. The AD623ARMZ is the 8-lead MSOP (RM-8) surface-mount version, while the AD623ARZ is the 8-lead SOIC version; the AD623ARZ-REEL7 is the tape-and-reel ordering code of the SOIC part. Electrically they are the same amplifier, but the land patterns differ, so the MSOP and SOIC parts are not interchangeable on the same PCB footprint.
Is AD623ARMZ RoHS compliant and what is its moisture level?
The AD623ARMZ is listed as RoHS3 compliant and REACH unaffected, with MSL 1 (unlimited floor life). Because MSL 1 carries no bake requirement before reflow, the part can be stored and then reflowed without a moisture soak as long as the packaging was not damaged. For automotive programs, confirm AEC-Q100 qualification separately, since that grade is not indicated for the standard commercial ordering code.
Where can I buy AD623ARMZ and what is the price?
Use the Request a Quote form on this page to obtain current pricing, stock position and a lead-time quote for the AD623ARMZ. Pricing for this part moves with distributor inventory and volume breaks, so a fixed figure quoted on a page would age quickly. Submit the quantity, reel or tube packaging preference and your target date, and the quote request will be answered with current terms for the exact 8-lead MSOP ordering code.
What is the lead time for AD623ARMZ?
Lead time for the AD623ARMZ depends on current manufacturer inventory and distributor stocking, so request a specific delivery commitment through the Request a Quote form on this page rather than relying on a generic figure. When planning a build, note that the part is normally supplied in tape-and-reel or tube packing; ask the quote to confirm the packing option, the minimum order quantity and the date the material is committed before scheduling the SMT line.

Справочные инженерные данные для AD623ARMZ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the AD623ARMZ when your design runs from 3 V to 12 V and the amplifier output must reach the ADC input range, because it is the only member of this 8-lead MSOP family that combines a 3 V minimum supply with a rail-to-rail output stage. Pick the AD823ARMZ if you need the same footprint and single-resistor gain setting but can live with roughly half the unity-gain bandwidth. Pick the AD621ARMZ when your supply is higher and you want the better gain accuracy and CMRR of the AD621 in an identical land pattern. Pick the AD620ARMZ only for legacy designs that already carry that part, since its supply span and output headroom are tighter. Pick the AD8221ARMZ or AD8229ARMZ when input noise or impedance matters more than speed, accepting the bandwidth reduction. Before substituting any part, confirm supply range, input common-mode range, REF pin use and gain equation in the data sheet.

Сравнение с аналогами

Параметр Этот товар AD823ARMZ AD621ARMZ AD620ARMZ AD8221ARMZ AD8229ARMZ
Package MSOP-8 (RM-8) MSOP-8 (RM-8) - same MSOP-8 (RM-8) - same MSOP-8 (RM-8) - same MSOP-8 (RM-8) - same MSOP-8 (RM-8) - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Gain Range 1 to 1000, single gain resistor 1 to 1000, single gain resistor 1 to 1000, single gain resistor 1 to 1000, single gain resistor 1 to 1000, single gain resistor 1 to 1000, single gain resistor
REF Pin Yes, output reference / offset Yes Yes Yes Yes Yes
Number of Channels 1 1 1 1 1 1

Ключевые отличия

  • Operates from a 3 V supply with a rail-to-rail output stage (против AD620ARMZ)
  • Much faster settling for multiplexed sensor channels (против AD8229ARMZ)
  • Single-resistor gain programming simplifies the BOM (против AD621ARMZ)
  • Higher speed than the AD823 family member in the same footprint (против AD823ARMZ)

Заметки по проектированию

The most common design error is assuming the AD623 can accept any common-mode voltage because it has a rail-to-rail output. The rail-to-rail specification applies to the output stage only; the input common-mode range is finite and is specified in the AD623 data sheet. Always check the sensor's common-mode voltage against that range, especially on 3.3 V supplies where the window is narrow. A second common mistake is leaving the REF pin floating, which lets noise and offset dominate the output - tie REF to the analog ground or drive it deliberately.

Place the gain-set resistor directly at the RG pin with the shortest possible trace, because parasitic capacitance at RG adds phase shift and can reduce stability at high gain. Keep the two input nets as a tight differential pair routed over a continuous ground plane, and return the sensor shield to the same reference node as REF. Place the input RC filter components symmetrically so the differential balance, and therefore the common-mode rejection at frequencies above roughly 1 kHz, is preserved.

Estimated: the AD623ARMZ draws roughly 0.6 mA per channel from the supply, so at a 3.3 V rail the dissipation is on the order of 2 mW - heat is rarely a concern in the MSOP-8 package. The real supply consideration is headroom: because the output swings to the rails, the usable output window on a 3.3 V supply is only about 0 V to 3.3 V before output saturation, so design the gain so the worst-case differential input does not push the output into the rails.

For long sensor cables, add a matched RC filter at each input (for example 100 Ohm plus 10 nF) to limit differential-mode and common-mode pickup before it is amplified. Keep the added capacitance roughly equal on both inputs, since unmatched filtering converts common-mode noise into differential error that no amount of on-chip CMRR can remove. Verify the resulting bandwidth against the 800 kHz unity-gain figure and against the expected 50/60 Hz rejection of your amplifier.

Информация о соответствии

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

RoHS3 compliant and REACH unaffected per the part listing; MSL 1 (unlimited floor life). AEC-Q100 qualification is not indicated for the standard commercial ordering code - confirm with the manufacturer for automotive programs.

Данные проверены: 2026-11-18 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

ad623armz reel7 ad623armz reel AD623ARMZ datasheet AD623ARMZ pinout AD623ARMZ datasheet pdf AD623ARMZ equivalent AD623ARMZ drop-in replacement AD623ARMZ vs AD620ARMZ AD623ARMZ MSOP-8 footprint AD623ARMZ single supply rail-to-rail instrumentation amplifier AD623ARMZ gain resistor calculation AD623ARMZ load cell amplifier AD623ARMZ price AD623ARMZ stock and lead time Analog Devices AD623ARMZ 8-MSOP

Связанные компоненты & термины

Analog Devices AD623 AD623ARMZ AD823ARMZ AD621ARMZ AD620ARMZ AD8221ARMZ AD8229ARMZ instrumentation amplifier differential amplifier op amp analog signal conditioning IC rail-to-rail output single-supply operation CMRR gain-set resistor 800 kHz bandwidth 300 mV/us slew rate MSOP-8 RM-8 package surface mount load cell bridge thermocouple RTD current shunt measurement RoHS REACH MSL 1 REF pin
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ