AD842KN - 80 MHz Wideband Current-Feedback Op Amp | Analog Devices
N.º da peça: AD842KN ✓ AtivoAD842KN Visão geral
An operational amplifier is an active analog circuit that uses high open-loop gain and negative feedback to amplify a differential input signal. The AD842 belongs to the current-feedback amplifier family. Current-feedback amplifiers divide a high-gain stage into an inverting input and a non-inverting input, allowing the closed-loop bandwidth to remain relatively stable as closed-loop gain changes. Within the broader signal-chain hierarchy, the AD842 sits between general-purpose voltage-feedback amplifiers and dedicated instrumentation, buffer, and line-driver circuits.
The AD842 family's main differentiators include its 80 MHz gain-bandwidth product, wideband operation, and ability to deliver comparatively high output current. These characteristics make it useful when driving moderate capacitance, driving low-impedance loads, or processing large-amplitude transient signals. Analog Devices identifies the CB process as the enabling technology for combining DC precision with wideband AC performance that was previously difficult to achieve in a monolithic operational amplifier.
The device is available in a 14-pin PDIP package for through-hole PCB assembly. Because it is a high-speed bipolar amplifier, board construction and decoupling strongly affect usable performance. Short feedback traces, a clean ground plane, and local supply bypassing help preserve the intended settling behavior and minimize RF pickup. A feedback resistor should be selected to match the source impedance and the load being driven rather than treating the amplifier as a voltage-only generic part.
Typical applications include laboratory instrumentation, current-to-voltage conversion, waveform conditioning, video and pulse-signal conditioning, and active analog filtering. It is particularly appropriate when the signal source is low impedance and the following stage requires a high-current output. The 14-pin through-hole package also simplifies prototype assembly and repair on laboratory or legacy industrial boards.
When designing around the AD842KN, verify gain-bandwidth behavior for the selected closed-loop gain and confirm that the load current and capacitive loading remain within the device operating limits. Stable feedback components, balanced trace geometry, and separate analog return paths are more important than minimizing board area alone. The device should also be evaluated for overload recovery and output saturation if the expected input waveform can exceed the intended operating range.
This page combines the manufacturer specifications, verified package information, pin-compatible family options, comparison data, and practical layout guidance so that engineers can evaluate the AD842KN against other wideband amplifiers before committing a design to production.
Alternativas drop-in para AD842KN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com AD842KN (mesmo formato e footprint) — diferindo em Gain-Bandwidth Product.
AD842KNZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AD842JN
✅ Drop-InConsulte o preço
Ver ficha técnica →AD842KH
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →AD842KN Classificações máximas e características elétricas
| Product Type | Wideband operational amplifier |
| Amplifier Architecture | Current-feedback amplifier |
| Process Technology | Junction-isolated complementary bipolar (CB) process |
| Number of Circuits | 1 amplifier |
| Gain-Bandwidth Product | 80 MHz |
| Supply Voltage Range | ±5 V to ±18 V |
| Package Type | 14-pin PDIP |
| Package Dimensions | 0.300 inch (7.62 mm) body width |
| Tipo de montagem | Through-hole |
| Input Offset Voltage | 1500 uV maximum |
| Corrente de alimentação | 6 uA typical |
| Input Noise Current | 3.5 uA |
| Common-Mode Rejection | 115 dB |
| Status RoHS | unknown |
| REACH Status | unknown |
Guia de Configuração de Pinos do AD842KN 0.300 inch (7.62 mm) body width
Configuração de pinos para AD842KN (pacote 0.300 inch (7.62 mm) body width). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para AD842KN.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
AD842KN é adequado para 6 aplicaçãos: Laboratory Instrumentation and Buffering, Pulse and Fast Transient Signal Conditioning, Active Analog Filtering, Current-to-Voltage Conversion, Video and RF-Interface Conditioning, Industrial Control and Legacy Through-Hole Boards.
Laboratory Instrumentation and Buffering
The AD842KN fits laboratory front ends that must buffer a low-impedance source before an ADC, oscilloscope, or analyzer. Its 80 MHz gain-bandwidth product provides substantially more bandwidth than a conventional precision op amp, while the current-feedback architecture supports rapid settling through moderate gain stages. The high-output-current capability is useful when the following stage presents a lower input impedance. Keep the feedback resistor close to the inverting input, provide local supply bypassing, and verify settling with the intended source and load. Temperature-range and offset-voltage requirements should also be checked when laboratory equipment operates across wide ambient conditions.
Recomendado
Pulse and Fast Transient Signal Conditioning
Use the AD842KN where pulse edges and fast transients must be amplified without the severe slew-rate limitation associated with many general-purpose op amps. The 80 MHz gain-bandwidth product and high-output-current design let the amplifier charge moderate parasitic capacitance and drive practical downstream loads. Because current-feedback amplifiers depend strongly on correct feedback-network values, select the feedback resistor using the gain and source-impedance relationship in the manufacturer datasheet. Add a small output isolation resistor when driving capacitive cabling, and keep the feedback trace short to avoid oscillation or irregular settling.
Recomendado
Active Analog Filtering
The AD842KN can serve as the active element in wideband filter sections where conventional voltage-feedback amplifiers do not provide adequate bandwidth or drive strength. Current-feedback amplifiers are particularly useful in low-impedance filter topologies because their gain-bandwidth relationship differs from that of voltage-feedback devices. The AD842's 80 MHz gain-bandwidth product supports higher-frequency signal paths, although actual usable bandwidth must be checked against the selected closed-loop gain and feedback resistor. Validate component tolerances and parasitic capacitance in simulation, and maintain short routing around the high-impedance summing node to preserve stability.
Recomendado
Current-to-Voltage Conversion
The AD842KN is appropriate for current-to-voltage conversion stages in sensor and test systems where a low-impedance current source must drive a feedback network. Its high-output-current capability reduces the distortion that can occur when the required conversion resistor produces a small signal node with a fast-changing load. Keep the sense resistor close to the amplifier's inverting input and return its current directly to the amplifier ground rather than through a shared noisy trace. Verify input common-mode range and output swing against the expected sensor current, and add a dedicated zero-input trim path when the measurement system requires accurate offset calibration.
Recomendado
Video and RF-Interface Conditioning
The AD842KN can condition low-level signals in video, communications, and RF test interfaces when the downstream path requires a stronger, faster output than a general-purpose amplifier can provide. Its 80 MHz gain-bandwidth product makes it relevant to baseband signal conditioning, although RF applications still require careful frequency-response analysis at the actual operating frequency. Use short, controlled-impedance traces, keep the feedback loop compact, and provide a stable reference plane to reduce radiated coupling. Decouple each supply rail locally, and check the amplifier's stability with the cable, connector, and termination that will be present in the finished system.
Recomendado
Industrial Control and Legacy Through-Hole Boards
The 14-pin PDIP package makes the AD842KN useful for industrial control, test equipment, and legacy through-hole boards where a surface-mount amplifier would require layout changes. The wideband current-feedback architecture supports signal paths that need more speed than conventional controller amplifiers, and the through-hole package remains practical for prototypes and low- to medium-volume assemblies. Confirm the exact temperature grade for industrial environmental conditions and verify that the supply rails remain within ±5 V to ±18 V. Prototype boards should include local bypass capacitors and a ground arrangement that does not force high-current return paths through sensitive signal wiring.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para AD842KN — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | AD842KNZ | AD842JN | AD842K |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 14-PDIP | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same |
| Amplifier Architecture | Current-feedback operational amplifier | Current-feedback operational amplifier | Current-feedback operational amplifier | Current-feedback operational amplifier |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
Principais diferenciais
- Wideband current-feedback performance in a through-hole package (vs AD8005ARZ)
- Higher output-drive capability than precision-oriented amplifiers (vs AD7492BRZ)
- Direct package-compatible family sourcing (vs AD842JN)
Notas de projeto
Treat the AD842KN as a high-speed analog component even though it uses a through-hole package. Place supply-bypass capacitors close to the device pins, provide an uninterrupted ground plane beneath and around the amplifier, and route the inverting input directly to the feedback resistor. Long loops around the feedback network can pick up RF signals and produce instability that is mistaken for a defective device.
Select the feedback resistor according to the current-feedback gain equation and source impedance in the Analog Devices datasheet rather than copying a voltage-feedback amplifier's resistor value. Keep the feedback components physically small and close to the relevant pins, and terminate unused inputs in accordance with the recommended configuration. When driving a cable or capacitive load, place a small isolation resistor at the output and verify settling in the complete system.
The AD842KN operates from dual ±5 V to ±18 V supplies. Check total supply span, output swing, and output-current demand against the application, and avoid using a ±18 V rail when the circuit only requires lower voltage. Place decoupling across each supply rail at the package, use separate return paths for high-current output returns, and test startup and overload recovery with the actual source and load attached.
Do not treat the 80 MHz gain-bandwidth product as a guaranteed 80 MHz closed-loop bandwidth at every gain setting or load. Current-feedback bandwidth also depends on the feedback resistor, source impedance, gain, and output loading. A 14-pin PDIP version may also differ from closely related SOIC members in thermal behavior and temperature-grade limits, so every pin and ordering-code substitution must be checked against the exact AD842 datasheet.
Informações de conformidade
Compliance declarations are not stated on the AD842 family pages identified for this part. The AD842KNZ ordering code indicates a lead-free finish, but formal RoHS, REACH, and halogen-free status should be confirmed for the exact orderable part. The standard AD842KN is not presented as an automotive-qualified variant.