Analog Devices

ADF4156BCPZ-RL7 - 6.2 GHz Fractional-N PLL Synthesizer | Analog Devices

N.º da peça: ADF4156BCPZ-RL7 ✓ Ativo
LFCSP-20 (20-lead WFQFN with exposed pad, CSP) Package 6.2 GHz Speed
MOQ: 1 |

ADF4156BCPZ-RL7 Visão geral

The Analog Devices ADF4156BCPZ-RL7 is a 6.2 GHz fractional-N frequency synthesizer with a single RF output, packaged in a 20-lead LFCSP (leadless chip-scale package) with an exposed thermal pad. The device combines a low-noise digital phase frequency detector (PFD), a precision charge pump, a programmable reference divider, and a Sigma-Delta based fractional-N interpolator, all controlled through a simple 3-wire serial interface.

A fractional-N frequency synthesizer is a phase-locked-loop based clock generator whose output frequency is produced by dividing a stable reference by a fractional ratio, using a Sigma-Delta modulator to shape quantization noise away from the carrier. In the wider taxonomy it sits under clock and timing ICs, then frequency synthesizer / PLL, then integer-N and fractional-N PLL architectures, ultimately part of the broader clock generation and timing-control silicon family.

Key features of the ADF4156 include a maximum synthesizer frequency of 6.2 GHz, an RF input frequency specified down to 0.5 GHz provided the minimum input slew rate of 400 V/us is respected, programmable output phase for applications that need a defined phase relationship between the RF output and the reference, and cycle slip reduction circuitry that shortens lock time without requiring a modified loop filter. All on-chip registers are accessed through the 3-wire interface.

Internally, the low-noise digital PFD and precision charge pump compare the divided feedback signal with the reference, driving the loop filter and the N divider in the feedback path. The Sigma-Delta fractional interpolator allows fine fractional frequency steps without the fine-tuning resolution penalty of an integer-N divider, which is what makes the part attractive for wireless transceiver local oscillators where channel spacing is narrow and phase noise directly limits receiver sensitivity and transmitter adjacent-channel rejection.

Typical deployments include cellular and wireless handset local oscillators, base-station receiver and transmitter up-conversion and down-conversion sections, Wi-Fi and microwave radio front ends, test and measurement instrumentation, and broadband satellite or microwave link synthesizers. The single-RF-output architecture keeps board area minimal for compact modules.

When laying out the board, treat the exposed pad as the primary thermal and RF return path: fill it with vias, keep the RF input trace short and matched, and place the loop filter components close to the charge pump and N-divider pins. The reference clock must be clean and stable, because reference phase noise is multiplied by N and appears directly at the output.

Alternativas drop-in para ADF4156BCPZ-RL7 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com ADF4156BCPZ-RL7 (mesmo formato e footprint) — diferindo em Package, Charge Pump, Charge-Pump Current, Lock Detect, Phase Detector.

Analog Devices
Package: 20-VFQFN exposed-pad CSP, 3.75 mm × 4 mm
Charge-Pump Current: Two selectable settings
Lock Detect: Digital lock detect
Comparar com ADF4156BCPZ-RL7 →
Analog Devices
Package: 20-pin LFCSP with exposed pad
Charge Pump: Programmable current
Comparar com ADF4156BCPZ-RL7 →
Analog Devices
Package: 20-lead LFCSP with exposed pad
Charge-Pump Current: Programmable
Lock Detect: Digital
Comparar com ADF4156BCPZ-RL7 →

ADF4154BCP-REEL

✅ Drop-In
Analog Devices
📦 LFCSP-20 (CP-20-12)
Fractional-N frequency synthesizer · 500 MHz to 4 GHz · 10 MHz to 4 GHz · 3.3 V · Programmable dual-modulus 4/5 or 8/9 · Programmable current · 3-wire serial interface · Digital lock detect

Consulte o preço

Ver ficha técnica →

ADF4153BCPZ-RL7

✅ Drop-In
Analog Devices
📦 LFCSP-20 (CP-20-12)
Fractional-N frequency synthesizer · 4 GHz · 1 · 2.7 V to 3.3 V · -40 °C to +85 °C · Three-wire external interface · External · Fractional-N

Consulte o preço

Ver ficha técnica →

ADF4157BCPZ-RL7

✅ Drop-In
Analog Devices
📦 LFCSP-20 (CP-20-12)
Fractional-N frequency synthesizer · 6 GHz · 25 bit · Sub-hertz at 6 GHz · 3.3 V · Separate supply for extended tuning voltage · Programmable · Programmable

Consulte o preço

Ver ficha técnica →

ADF4158BCPZ-RL7

✅ Drop-In
📦 LFCSP-20 (CP-20-12)
Same LFCSP-20 package and 3-wire interface; maximum synthesizer frequency 11 GHz versus 6.2 GHz (+77%), intended for higher-band wireless local oscillators

📋 Alternativa de referência (fora do catálogo)

ADF4159BCPZ-RL7

✅ Drop-In
📦 LFCSP-20 (CP-20-12)
Same LFCSP-20 footprint and fractional-N synthesizer core; maximum synthesizer frequency 13 GHz versus 6.2 GHz (+110%), covering higher microwave LO bands

📋 Alternativa de referência (fora do catálogo)

ADF4156BCPZ-RL

✅ Drop-In
📦 LFCSP-20 (CP-20-12)
Identical die, identical 6.2 GHz maximum synthesizer frequency and register map; only reel format differs (standard reel versus -RL7 7-inch reel), so key parameters match 100%

📋 Alternativa de referência (fora do catálogo)

ADF4156BCPZ-RL7 Especificações

Device Type Fractional-N frequency synthesizer (PLL)
Maximum Synthesizer Frequency 6.2 GHz
Minimum RF Input Frequency 0.5 GHz (at 400 V/us minimum slew rate)
RF Input Minimum Slew Rate 400 V/us
RF Output Count 1
Frequency Divider Architecture Sigma-Delta fractional-N with integer-N feedback divider
Phase Detector Low-noise digital PFD
Charge Pump Precision charge pump
Reference Divider Programmable
Output Phase Programmable
Lock Time Feature Cycle slip reduction circuitry
Serial Interface 3-wire (register write interface)
Encapsulamento LFCSP-20 (20-lead WFQFN with exposed pad, CSP)
Tipo de montagem Surface mount
Ordering Code Suffix -RL7 (tape and reel, 7-inch reel)
Status RoHS Compliant

Guia de Configuração de Pinos do ADF4156BCPZ-RL7 lfcsp-20 (20-lead wfqfn with exposed pad, csp)

Configuração de pinos para ADF4156BCPZ-RL7 (pacote lfcsp-20 (20-lead wfqfn with exposed pad, csp)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote lfcsp-20 (20-lead wfqfn with exposed pad, csp) para ADF4156BCPZ-RL7

Nenhum dado detalhado de pinagem disponível para ADF4156BCPZ-RL7.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

ADF4156BCPZ-RL7 é adequado para 6 aplicaçãos: Cellular Transmitter/Receiver Local Oscillator, Wi-Fi and Microwave RF Front End, Base Station and RF Test Instrumentation, Satellite and Broadband Link Modems, Industrial and IoT RF Sensor Nodes, High-Speed Clock Distribution and Data Converters.

📱

Cellular Transmitter/Receiver Local Oscillator

The ADF4156BCPZ-RL7 suits the up-conversion and down-conversion local oscillator sections of wireless transmitters and receivers, which is the exact role the manufacturer describes for the ADF4156 family. Its fractional-N Sigma-Delta interpolator delivers fine frequency steps that integer-N dividers cannot match, a necessity when channels sit close together or the operating band must be changed in the field. With a 6.2 GHz ceiling, the part covers the lower and mid bands of cellular front ends, and the single RF output keeps board area low in compact radio modules. Programmable output phase and the cycle slip reduction circuitry shorten re-lock time when the receiver switches channels. Loop filter components should sit close to the charge pump and N-divider pins, since loop bandwidth directly trades phase noise against lock time.

🌐

Wi-Fi and Microwave RF Front End

In Wi-Fi and microwave radio front ends, local oscillator phase noise directly limits receiver sensitivity and transmitter adjacent-channel rejection, so the low-noise digital phase frequency detector and precision charge pump of the ADF4156BCPZ-RL7 are the deciding features. The device synthesizes up to 6.2 GHz, which covers the 2.4 GHz and 5 GHz Wi-Fi bands and the lower portion of the microwave range used by wireless infrastructure equipment. Its programmable reference divider lets the same board serve multiple reference plans, and the 3-wire interface leaves the remaining pins for RF routing. Because the phase noise floor and spur performance are set by the external loop filter and by reference clock quality, use a clean, low-jitter reference and keep the loop filter network compact and shielded from the RF path.

🖥️

Base Station and RF Test Instrumentation

Base station and laboratory test equipment need a local oscillator that can be swept across many channels quickly while keeping spurs and phase noise inside the measurement floor. The ADF4156BCPZ-RL7 addresses the acquisition-time side of this problem directly: the cycle slip reduction circuitry described by the manufacturer shortens lock time without requiring a modified loop filter, so the original filter design can be retained. Its programmable output phase allows the instrument to set a defined phase relationship to the reference, which helps in coherent measurement setups and phase-sensitive calibration. The single RF output is a good match for single-channel vector sources. Instrument designers should still budget thermal path through the exposed pad and keep the reference input routed away from the RF output trace to avoid correlated spurs appearing at the carrier.

✈️

Satellite and Broadband Link Modems

Satellite and broadband link equipment relies on extremely stable, spectrally clean carrier generation, and the ADF4156BCPZ-RL7 delivers that with a low-noise digital PFD and a programmable reference divider driving a fractional-N core. The Sigma-Delta fractional interpolator allows fine channel spacing without sacrificing the divisor count, which matters when transponders or channels are only tens of kilohertz apart. The maximum synthesizer frequency of 6.2 GHz covers the majority of L-band and S-band downlink and uplink LO plans used in broadband satellite terminals. Programmable output phase supports coherent combining and calibration routines. Designers should pay close attention to reference clock purity, because reference phase noise is multiplied by N and lands directly at the carrier, and should thermally anchor the exposed pad for stable VCO behavior over temperature.

🧩

Industrial and IoT RF Sensor Nodes

Compact RF sensor nodes, industrial radios, and IoT gateways need a local oscillator that is cheap to integrate, simple to program, and stable enough for reliable demodulation. The ADF4156BCPZ-RL7 offers a single RF output, a small 20-lead LFCSP footprint, and a 3-wire register interface, so a microcontroller can configure it directly over an SPI-style bus without extra glue logic. The fractional-N core lets the same hardware cover several regional channel plans simply by changing the N and fractional registers, which reduces the number of board variants. Cycle slip reduction helps the node re-acquire quickly after a sleep or a frequency hop. Because the package is small, the exposed pad must be connected to a solid ground pour with adequate vias, and the reference clock should be routed away from the sensitive RF input to preserve phase noise.

⏱️

High-Speed Clock Distribution and Data Converters

High-speed data converters and digital engines often need a low-jitter, programmable clock source that can be retuned to match a specific sample rate or to align two subsystems. The ADF4156BCPZ-RL7 fits that role because its output frequency is digitally programmable through the register interface while its reference input can be a clean system clock, and because the reference divider lets a high-frequency source be divided down internally. Programmable output phase permits deliberate alignment between the synthesized clock and an external sampling edge, which assists in calibration of mixed-signal chains. The RF output stage drives up to 6.2 GHz, so the same device can serve as a sample-clock generator or as a local oscillator in the same chassis. Keep the loop filter tight and low-inductance and take care that the 3-wire programming bus is not routed adjacent to the RF output trace.

What is the ADF4156BCPZ-RL7?
The ADF4156BCPZ-RL7 is an Analog Devices 6.2 GHz fractional-N frequency synthesizer with one RF output, packaged in a 20-lead LFCSP with an exposed pad. According to the ADF4156 datasheet, it consists of a low-noise digital phase frequency detector, a precision charge pump, a programmable reference divider, and a Sigma-Delta based fractional interpolator, with all on-chip registers controlled by a 3-wire interface.
What is the maximum output frequency of ADF4156BCPZ-RL7?
The ADF4156 synthesizes up to 6.2 GHz from its reference input, as stated in the manufacturer datasheet general description. The device is described as a 6.2 GHz fractional-N frequency synthesizer intended to implement local oscillators in the up-conversion and down-conversion sections of wireless receivers and transmitters. The -RL7 suffix denotes the tape-and-reel, 7-inch reel order option of the same die and package.
What is the minimum RF input frequency for ADF4156BCPZ-RL7?
The RF input specification is 0.5 GHz minimum according to the ADF4156 datasheet. The datasheet also notes that lower RF frequencies can be used if the minimum input slew rate specification of 400 V/us is met. To square up a slower or lower-amplitude signal before feeding it into the RF input, the datasheet suggests using an appropriate LVDS driver such as the FIN1001 from Fairchild Semiconductor.
Does ADF4156BCPZ-RL7 support fractional-N operation?
Yes, the ADF4156 uses a Sigma-Delta based fractional interpolator, which is what makes it a fractional-N rather than an integer-N synthesizer. This architecture produces fine frequency steps without the resolution penalty of a pure integer-N divider, which is essential in wireless transceivers where channel spacing is narrow. Combined with the programmable reference divider and the precision charge pump, the fractional interpolator sets the achievable frequency granularity and in-band phase noise.
How is the ADF4156BCPZ-RL7 controlled and programmed?
All on-chip registers of the ADF4156 are controlled through a simple 3-wire serial interface, as stated in the manufacturer product description. The same description notes that the RF output phase is programmable for applications requiring a specific phase relationship between the output and the reference. Because programming is register-based, a three-wire SPI-compatible bus is sufficient; use the pin-description table in the ADF4156 datasheet when assigning board-level tracks.
What is the cycle slip reduction feature in the ADF4156?
The ADF4156 features cycle slip reduction circuitry, which leads to faster lock times without the need for modifications to the loop filter. This matters most in burst-mode receivers and transmitters that must re-lock between channels quickly. Because the improvement comes from on-chip circuitry rather than an external component change, the loop filter design can stay as originally calculated while acquisition time is reduced.
ADF4156BCPZ-RL7 vs ADF4157BCPZ-RL7 - which should I choose?
The ADF4157 is the closest same-package relative of the ADF4156, sharing the 20-lead LFCSP footprint and the Sigma-Delta fractional-N architecture, but its maximum synthesizer frequency is higher. Choose the ADF4156BCPZ-RL7 when your local oscillator must cover up to 6.2 GHz, and move to the ADF4157 family only when the required output frequency exceeds that ceiling. Both use the same 3-wire programming model, so the board and firmware port cleanly.
Can ADF4158BCPZ-RL7 or ADF4159BCPZ-RL7 replace ADF4156BCPZ-RL7?
The ADF4158 and ADF4159 are often listed as equivalents to the ADF4156 because they share the fractional-N PLL family features and the 20-lead LFCSP package, but they target higher maximum output frequencies. They are therefore not one-for-one replacements when the design locks below 6.2 GHz. For a true drop-in substitution with the same frequency range and pin arrangement, the ADF4156BCPZ-RL and ADF4156BCPZ order options are the safest choices because they use the identical die and footprint.
What is the best drop-in replacement for ADF4156BCPZ-RL7?
The best drop-in replacement is ADF4156BCPZ-RL, the tape-and-reel order option of the identical ADF4156 silicon in the same 20-lead LFCSP package, with identical 6.2 GHz maximum synthesizer frequency and register map. ADF4156BCPZ in tray packaging is functionally identical for prototype and low-volume builds. No cross-brand drop-in alternative with a matching LFCSP-20 footprint and 6.2 GHz fractional-N specification was identified in the cross-reference data reviewed.
When should I choose ADF4156BCPZ-RL7 over an integer-N PLL?
Choose the ADF4156BCPZ-RL7 when the required frequency resolution is finer than an integer-N divider can deliver, such as in narrow-spaced cellular or Wi-Fi channels, or when channel spacing changes at runtime. The Sigma-Delta fractional interpolator provides fine fractional steps while keeping the reference divider programmable. For fixed, coarse-spaced frequencies with relaxed phase-noise requirements, an integer-N synthesizer such as the ADF4106 or ADF4107 families may be simpler and lower cost.
Is ADF4156BCPZ-RL7 suitable for microwave and broadband RF designs?
Yes, the ADF4156 was designed for wireless receiver and transmitter local oscillators in both up-conversion and down-conversion sections, and its 6.2 GHz ceiling covers the lower and mid microwave bands used by cellular infrastructure, Wi-Fi, and microwave backhaul equipment. Because the part has a single RF output, it suits compact radio modules where board area is constrained. Confirm the reference frequency and required channel spacing against your synthesizer plan before layout release.
How should I lay out the ADF4156BCPZ-RL7 on a PCB?
Fill the exposed pad of the LFCSP-20 package with a solid copper plane and stitch it to ground with a dense via array, since the pad is the main thermal and RF return path. Place the loop filter network close to the charge pump and N-divider pins to minimize loop-area pickup of board noise. Keep the RF input trace short, use a controlled-impedance line, and route it away from the reference and digital programming traces to protect phase noise.
What are the key specifications of ADF4156BCPZ-RL7 that engineers should know?
The core figures are a 6.2 GHz maximum synthesizer frequency, a 0.5 GHz minimum RF input with a 400 V/us minimum slew-rate requirement, one RF output, a programmable reference divider, programmable output phase, cycle slip reduction for faster lock, and a 3-wire register interface. The package is a 20-lead LFCSP with an exposed pad in the -RL7 tape-and-reel order option. All figures come from the Analog Devices ADF4156 datasheet and product page.
Where can I download the ADF4156BCPZ-RL7 datasheet PDF?
The manufacturer datasheet PDF is published by Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/ADF4156.pdf, and the product page with datasheet links is at https://www.analog.com/en/products/adf4156.html. The same datasheet covers the ADF4156BCPZ, ADF4156BCPZ-RL, and ADF4156BCPZ-RL7 order options, since they share the same die and LFCSP-20 package. Pin descriptions and register maps are in the same document.
Where can I buy ADF4156BCPZ-RL7 and what is the price?
Availability and current pricing for the ADF4156BCPZ-RL7 are handled through the Request a Quote form on this page, where the exact MPN, target quantity, and reel requirements can be submitted directly. Lead time and stock position for this tape-and-reel order option are confirmed at the same time, so a single request covers both commercial questions. The Analog Devices product page and manufacturer datasheet remain the authoritative technical references for the device.
What is the lead time and stock status of ADF4156BCPZ-RL7?
The current lead time and stock position for the ADF4156BCPZ-RL7 are confirmed through the Request a Quote form on this page. Because the -RL7 code denotes a specific 7-inch tape-and-reel packaging configuration of the standard ADF4156 die, quantities and reel packaging can be committed together with the order rather than being assumed. The manufacturer product page lists the ADF4156 as an active part for new designs.
Is the ADF4156BCPZ-RL7 RoHS compliant and available in automotive grade?
The ADF4156BCPZ-RL7 is RoHS compliant and REACH compliant according to the manufacturer and distributor listing data for this part. The standard ADF4156BCPZ order option is not qualified to AEC-Q100 for automotive applications, so vehicle-mounted designs should evaluate an automotive-qualified alternative or a different vendor program. The ADF4156 family is intended for industrial, telecom, and consumer wireless equipment.

Dados de referência de engenharia para ADF4156BCPZ-RL7 — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the ADF4156BCPZ-RL7 when your local oscillator must reach up to 6.2 GHz, your channel plan needs the fine resolution that only a Sigma-Delta fractional-N core delivers, and your board is built around the 20-lead LFCSP footprint with a 3-wire programming bus. If you need the identical function in a different reel format, ADF4156BCPZ-RL is a 100% parameter match and drops into the same footprint. If your design may later move to higher LO bands, ADF4157BCPZ-RL7 (8 GHz), ADF4158BCPZ-RL7 (11 GHz), or ADF4159BCPZ-RL7 (13 GHz) share the package and programming model, so the PCB carries the upgrade path even though phase noise and current draw differ. ADF4154BCP-REEL covers up to 13.6 GHz in the same footprint. Choose ADF4153BCPZ-RL7 only when 4 GHz is a hard ceiling and lower cost matters more than headroom. For coarse, fixed channels with relaxed phase-noise limits, an integer-N part may be a better fit.

Comparação com alternativas

Parâmetro Este produto ADF4154BCP-REEL ADF4153BCPZ-RL7 ADF4157BCPZ-RL7 ADF4158BCPZ-RL7 ADF4159BCPZ-RL7 ADF4156BCPZ-RL
Package LFCSP-20 (20-lead WFQFN, exposed pad) LFCSP-20 - same LFCSP-20 - same LFCSP-20 - same LFCSP-20 - same LFCSP-20 - same LFCSP-20 - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Device Type Fractional-N frequency synthesizer (single RF PLL) Fractional-N PLL Fractional-N PLL Fractional-N PLL Fractional-N PLL Fractional-N PLL Fractional-N PLL
Maximum Synthesizer Frequency 6.2 GHz 13.6 GHz (+120%) 4 GHz (-35%) 8 GHz (+29%) 11 GHz (+77%) 13 GHz (+110%) 6.2 GHz (identical)
RF Output Count 1 1 1 1 1 1 1 (identical)
Programmable Output Phase Yes Yes Yes Yes Yes Yes Yes (identical)
Cycle Slip Reduction Circuitry Yes Yes Yes Yes Yes Yes Yes (identical)
Serial Control Interface 3-wire register interface 3-wire 3-wire 3-wire 3-wire 3-wire 3-wire (identical)
Ordering / Packaging Option -RL7, tape and reel, 7-inch reel -REEL, tape and reel -RL7, tape and reel -RL7, tape and reel -RL7, tape and reel -RL7, tape and reel -RL, tape and reel
RoHS / REACH Compliance Compliant / Compliant Compliant / Compliant Compliant / Compliant Compliant / Compliant Compliant / Compliant Compliant / Compliant Compliant / Compliant

Principais diferenciais

  • Same-die drop-in options exist for the identical 6.2 GHz specification and LFCSP-20 footprint (vs ADF4156BCPZ-RL)
  • Higher maximum synthesizer frequency in the same package for future band expansion (vs ADF4157BCPZ-RL7)
  • Available spectrum above the 6.2 GHz ceiling without a footprint change (vs ADF4158BCPZ-RL7)
  • Cycle slip reduction circuitry shortens acquisition time (vs ADF4153BCPZ-RL7)

Notas de projeto

Treat the exposed pad of the LFCSP-20 package as both the thermal path and the high-frequency return path. Fill the pad with a solid ground pour, then add a dense via array (a 3x3 to 5x5 grid is a common starting point) dropping to the ground plane on the opposite layer, and keep those vias clear of the RF input and output escape routes. Route the RF input as a short, controlled-impedance trace with no stubs or test pads on the line, and place the loop filter components close to the charge pump and N-divider pins so the loop area stays small and does not pick up switching noise from adjacent circuitry.

Reference clock quality dominates output phase noise because reference noise is multiplied by N and appears at the carrier. Feed the reference input from a clean source with minimal jitter, keep that trace short and shielded from the RF output, and observe the 400 V/us minimum input slew rate; if the RF input is driven from a slower or lower-amplitude source, square it up with a suitable driver such as the FIN1001 LVDS driver cited in the datasheet. Isolate the 3-wire programming bus from the RF output trace, and keep the loop filter values within the ranges given in the datasheet tables so the Sigma-Delta fractional spur and phase noise trade-off stays as intended.

Estimated: with the exposed pad bonded to a solid ground pour through a via array and typical consumer/industrial board construction, the junction-to-ambient rise for the device at its rated supply and interface loading is on the order of a few tens of degrees, but the exact figure depends on the via count, copper area, and ambient airflow. In a sealed plastic enclosure with no dedicated ground pour under the pad, the pad can become the hottest region on the board and drift the VCO. Anchor the ground plane area under the pad, keep the RF output line away from hot components, and verify temperature rise at the highest supported ambient before volume release.

Two mistakes recur in designs using this class of device. First, the RF input minimum slew-rate requirement of 400 V/us is easy to violate when the input comes from a slow comparator or a low-amplitude divider output, which degrades phase noise and can cause unreliable locking; check the input waveform at the pin, not at the driver output. Second, do not swap in a family member with a lower maximum synthesizer frequency, such as a 4 GHz part, without re-verifying the highest LO frequency in the design, because the output simply cannot reach it. Confirm the exact order option code on the reel label before committing to a build, since tray and reel variants of the same die share one part number body but differ in logistics.

Informações de conformidade

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Sem chumbo
Yes
Sem halogênios
Unknown
Minerais de conflito
Unknown

RoHS and REACH compliance are confirmed in the distributor listing data for this part. The standard ADF4156BCPZ order option is not AEC-Q100 qualified for automotive use. Halogen-free and conflict-minerals status were not stated in the available manufacturer or distributor data.

Dados verificados em: 2026-11-20 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

ADF4156BCPZ-RL7 ADF4156BCPZ-RL7 datasheet ADF4156BCPZ-RL7 datasheet pdf ADF4156BCPZ-RL7 pinout ADF4156BCPZ-RL7 equivalent ADF4156BCPZ-RL7 replacement ADF4156BCPZ-RL7 price ADF4156BCPZ-RL7 stock Analog Devices ADF4156 fractional-N PLL ADF4156 6.2 GHz frequency synthesizer LFCSP-20 PLL synthesizer ADF4156 vs ADF4157 ADF4156 vs ADF4159 ADF4156 wireless transceiver local oscillator fractional-N PLL 3-wire interface RF synthesizer

Componentes & termos relacionados

Analog Devices ADF4156 ADF4156BCPZ-RL7 ADF4156BCPZ-RL ADF4153BCPZ-RL7 ADF4154BCP-REEL ADF4157BCPZ-RL7 ADF4158BCPZ-RL7 ADF4159BCPZ-RL7 fractional-N frequency synthesizer phase locked loop PLL Sigma-Delta fractional interpolator phase frequency detector precision charge pump programmable reference divider local oscillator wireless transmitter and receiver LFCSP-20 leadless chip-scale package QFN family surface mount SMD 3-wire serial interface cycle slip reduction RF input slew rate phase noise RoHS REACH
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ