Analog Devices

ADM489ARUZ - Full-Duplex RS-485/RS-422 | Analog Devices

N.º da peça: ADM489ARUZ ✓ Ativo
4.5 V to 5.5 V Vdss EIA RS-485 and EIA RS-422 Rds(on) 16-pin TSSOP Package
MOQ: 1 |

ADM489ARUZ Visão geral

The Analog Devices ADM489ARUZ is a low-power, full-duplex differential line transceiver designed for balanced RS-485 and RS-422 data links, with one driver and one receiver housed in a 16-pin TSSOP package. It operates from a 4.5 V to 5.5 V supply, supports data rates up to 250 kbps, and uses slew-rate-limited signaling for reduced electromagnetic interference on multipoint bus networks.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential voltages for reliable communication over cables and long interconnects. In the hierarchy of electronic components, it belongs to the interface IC family and the broader category of data transceivers. Balanced differential signaling helps reject common-mode noise, while the full-duplex architecture permits simultaneous transmitting and receiving through separate differential pairs.

The ADM489 provides separate driver-disable and receiver-enable control functions, allowing the transmitter to be released during reception and supporting a multipoint bus configuration. Its low-power design is intended to reduce system consumption, while the slew-rate-limited driver helps limit high-frequency harmonics on the cable. The 16-pin TSSOP package offers a compact surface-mount footprint suitable for industrial control, instrumentation, and communications equipment.

Because the ADM489 is a full-duplex device, each transceiver requires a dedicated differential driver connection and a separate differential receiver connection. The EIA RS-485 provisions cited by the Analog Devices datasheet include driver-disable capability, support for as many as 32 receivers on one line, and safety behavior during line contention. Only one driver should be active at a time, even though the device is electrically designed to withstand contention conditions.

Typical uses include industrial RS-485 buses, remote sensor links, laboratory equipment, building controls, and embedded instrumentation. The 250 kbps maximum signaling rate is appropriate for moderate-speed control and monitoring networks rather than high-speed backplane or Ethernet applications. The 4.5 V to 5.5 V supply range also makes the device suitable for conventional 5 V industrial and embedded systems.

PCB design should provide a continuous return path beneath the differential pair, minimize stubs from connectors and test points, and use controlled-impedance routing where cable transitions occur. Place the transceiver close to the connector, keep the RS-485 and RS-422 nets away from switching nodes, and follow the manufacturer’s grounding and termination guidance. Decoupling capacitors should be positioned close to the supply and ground pins.

This page organizes the ADM489ARUZ interface, package, operating limits, application guidance, and selection considerations into an engineering-focused reference. It also identifies the verified drop-in alternatives that preserve the same TSSOP footprint and distinguishes true device replacements from unrelated RS-485 products with different transceiver architecture.

Alternativas drop-in para ADM489ARUZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Nenhuma alternativa drop-in disponível para este produto.

Solicitar alternativas

ADM489ARUZ Especificações

Product Type Full-duplex differential line transceiver
Supported Standards EIA RS-485 and EIA RS-422
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 250 kbps
Driver Count 1 driver
Receiver Count 1 receiver
Duplex Mode Full duplex
Driver Output Type Slew-rate-limited differential output
Bus Configuration Multipoint bus transmission
Maximum Receivers per Line 32 receivers
Encapsulamento 16-pin TSSOP
Tipo de montagem Surface mount

Guia de Configuração de Pinos do ADM489ARUZ 16-pin tssop

Configuração de pinos para ADM489ARUZ (pacote 16-pin tssop). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 16-pin tssop para ADM489ARUZ

Nenhum dado detalhado de pinagem disponível para ADM489ARUZ.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

ADM489ARUZ é adequado para 6 aplicaçãos: Industrial RS-485 Control Bus, Remote Sensor Instrumentation, Building and HVAC Controls, Laboratory and Test Equipment, Telecommunications Power and Monitoring, Embedded Equipment Communications.

🏭

Industrial RS-485 Control Bus

The ADM489ARUZ is suitable for an industrial control bus that requires balanced differential signaling and full-duplex operation over separate transmit and receive pairs. Its 4.5 V to 5.5 V supply range matches conventional 5 V controller electronics, while the 250 kbps maximum rate is sufficient for supervisory commands, machine status, and sensor data. Place the transceiver near the field connector, maintain a continuous ground reference, and follow the Analog Devices guidance for bus termination and driver enable control. Because only one driver should be active at a time on a shared RS-485 line, the host controller must enforce the correct enable sequence during arbitration and fault recovery.

🧩

Remote Sensor Instrumentation

The ADM489ARUZ can connect remote sensors or instrumentation nodes to a central controller over a balanced RS-422 or RS-485 cable. Full-duplex communication permits measurement requests and returning data to overlap when separate differential pairs are used, reducing dead time compared with a direction-controlled half-duplex link. The device’s 250 kbps rate supports moderate-rate environmental, process, and equipment-monitoring data rather than high-volume streaming. For long cables, place termination at the physical ends of the bus, avoid unnecessary stubs, and use a low-noise 5 V supply. Differential routing also helps reject common-mode noise encountered near motors, contactors, and variable-frequency drives.

🏠

Building and HVAC Controls

The ADM489ARUZ is appropriate for building-control equipment that distributes commands and gathers status through balanced RS-485 links. Its low-power 4.5 V to 5.5 V operation supports embedded controllers and room equipment, while the full-duplex arrangement simplifies simultaneous command transmission and sensor-response reception where four-wire wiring is available. The 250 kbps limit is more than adequate for HVAC controllers, lighting interfaces, access-control terminals, and environmental monitors. Designers should separate the transceiver’s differential pair from switching regulators and relay wiring, route the pair as a continuous impedance-controlled connection, and provide surge protection at externally accessible connectors.

🔬

Laboratory and Test Equipment

The ADM489ARUZ can bridge laboratory instruments and automated test systems that use balanced RS-485 or RS-422 links for remote commands and measurement results. The full-duplex topology supports separate paths for commands and returned data, reducing protocol-direction complexity, while the 250 kbps rate is suitable for configuration, status, and low-bandwidth measurement traffic. Its compact 16-pin TSSOP package helps preserve board area in multi-channel test equipment. Keep the analog and digital grounds arranged according to the manufacturer guidance, avoid long unprotected traces outside the transceiver, and consider galvanic isolation when the equipment connects to long cables or separate power domains.

🌐

Telecommunications Power and Monitoring

The ADM489ARUZ can serve as the balanced communications interface for telecommunications power shelves, battery systems, and environmental monitoring units. The 5 V operating range integrates with conventional line-card logic, and the full-duplex arrangement allows a unit to transmit alarms while receiving configuration or measurement data. The 250 kbps signaling rate is sufficient for supervisory channels rather than high-throughput traffic. In these systems, route the RS-485 or RS-422 pair away from high-current switching stages, use a solid ground-plane return, and apply appropriately rated surge and ESD protection at external cable interfaces. Firmware must ensure that only one transmitter drives the bus during a given interval.

🔧

Embedded Equipment Communications

The ADM489ARUZ is useful in embedded equipment that needs a robust balanced-data port for configuration, diagnostics, and field upgrades. Its 16-pin TSSOP package is compact, its 250 kbps rate suits low-bandwidth service traffic, and its full-duplex operation removes the need to switch a shared two-wire bus direction. The device can therefore pair with an embedded microcontroller or application processor through standard logic-level enable and data pins. Keep the data and differential-line routing away from processor clocks and switching power nodes, place local decoupling at the device, and label external connector pins to prevent confusion between the full-duplex driver and receiver pairs.

What is the ADM489ARUZ?
The ADM489ARUZ is a low-power, full-duplex, one-driver and one-receiver differential transceiver for EIA RS-485 and RS-422 links. According to the Analog Devices ADM488/ADM489 datasheet, it operates from 4.5 V to 5.5 V, supports signaling rates up to 250 kbps, and is packaged in a 16-pin TSSOP. It suits balanced, point-to-point, or multipoint industrial communication systems requiring separate transmit and receive pairs.
What are the key specifications of ADM489ARUZ that engineers should know?
The principal ADM489ARUZ specifications are a 4.5 V to 5.5 V supply, 250 kbps maximum data rate, full-duplex operation, one differential driver, one differential receiver, and EIA RS-485/RS-422 compatibility. The Analog Devices ADM488/ADM489 datasheet also identifies a slew-rate-limited driver and support for up to 32 receivers on an RS-485 line. These characteristics place it among low-power interface ICs for industrial and embedded balanced-data links.
Is ADM489ARUZ suitable for RS-485 and RS-422 applications?
Yes, the ADM489ARUZ supports both EIA RS-485 and EIA RS-422 communication. According to the Analog Devices ADM488/ADM489 datasheet, the driver can be disabled so the device can operate on an RS-485 multidrop bus, while the full-duplex architecture also supports RS-422 links using separate differential channels. Ensure that only one driver on a shared bus is enabled at a time.
What is the maximum data rate of ADM489ARUZ?
The ADM489ARUZ supports a maximum signaling rate of 250 kbps. According to the Analog Devices ADM488/ADM489 datasheet, the device is a slew-rate-limited EIA RS-485 transceiver designed for low-power balanced transmission. This rate is well suited to industrial control, sensor networking, and equipment monitoring, but it is not intended for Ethernet-speed links or other high-rate protocols.
Where can I download the ADM489ARUZ datasheet PDF?
The official ADM489ARUZ datasheet is available from Analog Devices at the ADM488_489 PDF link listed on this page. The document covers the shared ADM488 and ADM489 family, including the ADM489’s full-duplex architecture, 4.5 V to 5.5 V supply range, 250 kbps operation, RS-485 driver-disable behavior, electrical characteristics, and recommended application circuits.
Where can I find the ADM489ARUZ pinout?
The ADM489ARUZ pin assignment is shown in the pin-configuration section of the official Analog Devices ADM488/ADM489 datasheet. The device uses a 16-pin TSSOP package, and its pins include the separate driver, receiver, logic-control, supply, and ground connections. Use the package drawing and pin-description table together when assigning PCB tracks rather than inferring functions from another RS-485 transceiver.
What is the difference between ADM489ARUZ and ADM489ARUZ-REEL?
ADM489ARUZ and ADM489ARUZ-REEL represent the same ADM489 device offered with different order packaging, while ADM489ARUZ identifies the specified tube-packed configuration used for this listing. According to the product-order information referenced by the manufacturer, electrical performance is unchanged; procurement should match the required mounting and shipment format. Tape-and-reel order codes are not counted as functionally different alternatives.
What can replace ADM489ARUZ?
A direct replacement for ADM489ARUZ must preserve the 16-pin TSSOP footprint, full-duplex architecture, 4.5 V to 5.5 V supply range, approximately 250 kbps class of operation, and RS-485/RS-422 logic interface. Equivalent products that are half-duplex, use a different package, or require different control pins are not true drop-in replacements. Use the manufacturer pin table and electrical-characteristic tables to confirm any proposed substitute.
What is the best Analog Devices equivalent for ADM489ARUZ?
The closest same-family choice is another ordering configuration of the ADM489, provided its package suffix and shipping format meet the assembly requirement. The Analog Devices ADM488/ADM489 datasheet describes ADM488 and ADM489 as related transceivers, but ADM488 is a half-duplex product and therefore does not preserve the ADM489ARUZ’s simultaneous transmit and receive architecture. Confirm the exact pinout before treating any related part as interchangeable.
Is ADM489ARUZ the same as a half-duplex RS-485 transceiver?
No, the ADM489ARUZ is a full-duplex transceiver with one driver and one receiver, while many common RS-485 devices are half-duplex and share a single bidirectional pair. According to the Analog Devices ADM488/ADM489 datasheet, the ADM489 provides separate differential driver and receiver connections. A half-duplex replacement may use a similar package but normally cannot replace the ADM489 without changing the PCB and system architecture.
When should I choose ADM489ARUZ over a half-duplex RS-485 transceiver?
Choose the ADM489ARUZ when the system requires continuous, simultaneous transmission and reception over separate balanced pairs. Its full-duplex architecture avoids software or hardware direction control between bus states. A half-duplex transceiver can be preferable when only one wire pair is available, bus direction must be controlled, or cable and installation costs outweigh the value of simultaneous operation.
Where can I buy ADM489ARUZ online?
Use the Request a Quote form on this page to request current availability, lead time, and order handling for ADM489ARUZ. The manufacturer product page and authorized distribution listings can be reviewed for technical documentation and ordering information. XAIPART will confirm the exact 16-pin TSSOP configuration, current lifecycle status, quantity requirements, and shipment format before an order is placed.
What is the price of ADM489ARUZ?
Current commercial terms for ADM489ARUZ are shown through the Request a Quote form on this page. Submit the required quantity, target package configuration, and delivery location to obtain an up-to-date quotation. The form is also the appropriate route for confirming minimum order quantity, production-volume pricing, stock availability, and expected lead time.
What is the lead time for ADM489ARUZ?
The current lead time for ADM489ARUZ should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, assembly format, inventory position, and approved sourcing channels. Include your forecast volumes and required delivery date in the request so the order confirmation can reflect the appropriate schedule.
Is ADM489ARUZ in stock?
Current inventory for ADM489ARUZ is confirmed through the Request a Quote form on this page. Stock status can change rapidly and may depend on the exact ordering suffix and shipment format. Submit the required quantity and assembly method to receive a current availability response, including any applicable minimum order quantity and lead time.
Can ADM489ARUZ be used in industrial automation systems?
Yes, the ADM489ARUZ fits industrial automation links that use EIA RS-485 or RS-422 balanced signaling at rates up to 250 kbps. The Analog Devices ADM488/ADM489 datasheet identifies multipoint bus communication, low-power operation, and slew-rate-limited outputs as key characteristics. Use appropriate cable termination, surge protection, grounding, and isolation practices for the installation environment.

Dados de referência de engenharia para ADM489ARUZ — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose ADM489ARUZ when the design requires a full-duplex RS-485 or RS-422 interface, one driver and one receiver, operation from a 4.5 V to 5.5 V supply, and signaling up to 250 kbps in a 16-pin TSSOP package. Its separate transmit and receive channels simplify continuous bidirectional communication and eliminate the need to share one pair between driver and receiver. Do not select it for a two-wire half-duplex architecture unless the PCB is deliberately redesigned. Likewise, a half-duplex device with a similar TSSOP outline is not a drop-in replacement because its data, enable, and receiver paths may differ. Verify the manufacturer pin table, supply limits, propagation timing, bus loading, and environmental ratings against the final schematic before release. The ADM489’s slew-rate-limited output is useful for reducing cable harmonics, but correct differential routing, grounding, termination, and external surge protection remain essential in industrial environments.

Comparação com alternativas

Parâmetro Este produto
Brand Analog Devices
Package 16-pin TSSOP
Transceiver Type Full-duplex differential line transceiver
Supported Standards EIA RS-485 and EIA RS-422
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 250 kbps
Driver and Receiver Count 1 driver and 1 receiver
Driver Characteristics Slew-rate-limited differential output
Bus Support Multipoint bus with up to 32 receivers

Notas de projeto

Route the RS-485 and RS-422 differential pairs as a coupled pair over a continuous ground plane, with the driver and receiver connections returned to the transceiver through nearby ground vias. Avoid routing through digital clocks, switching-regulator nodes, relay contacts, or display circuitry. Keep the transceiver near the external connector so transient-energy paths do not spread across the logic board. Maintain the differential pair’s geometry through connectors and away from branch stubs.

The ADM489 is full duplex, so its transmit and receive channels are separate; it cannot be used as though it were a half-duplex shared-bus device without changing the wiring and control strategy. The Analog Devices ADM488/ADM489 datasheet states that only one RS-485 driver should be enabled at a time. Firmware and external logic must therefore enforce mutually exclusive driver-enable states, including after reset, timeout, or fault recovery.

Place the recommended supply bypass capacitor immediately adjacent to the ADM489ARUZ supply and ground pins, and provide a low-impedance ground return without long loops. Keep the transceiver supply source separate from high-current switching stages where practical. Decoupling requirements, capacitor values, and allowable supply ripple must be taken from the manufacturer datasheet because operating-condition limits were not established for this record.

The slew-rate-limited driver reduces cable harmonics, but layout and filtering remain important in electrically noisy installations. Keep protected cable interfaces away from switching nodes, use the shortest practical route from the transceiver to protection components, and avoid long unshielded traces. Termination should be installed only where required by the bus topology and cable length. External surge protection must be selected to suit the installation’s ground-reference and isolation arrangement.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

Compliance status should be confirmed from the current manufacturer product documentation or the exact assembled-part record before regulatory submission.

Dados verificados em: 2026-11-14 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

ADM489ARUZ ADM489ARUZ datasheet ADM489ARUZ datasheet pdf ADM489ARUZ pinout ADM489ARUZ replacement ADM489ARUZ equivalent ADM489ARUZ cross reference ADM489ARUZ TSSOP-16 ADM489ARUZ 250kbps ADM489ARUZ RS-485 transceiver Analog Devices ADM489ARUZ ADM489ARUZ price

Componentes & termos relacionados

Analog Devices ADM489ARUZ ADM489 RS-485 RS-422 EIA RS-485 EIA RS-422 full-duplex transceiver differential line transceiver interface IC data transceiver semiconductor TSSOP-16 TSSOP package surface-mount package SMD slew-rate-limited driver differential signaling common-mode rejection multipoint bus 250 kbps 4.5 V to 5.5 V power supply industrial automation building controls
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ