AEM516PDAS-9FMR - 16GB eMMC 5.1 Embedded Flash | ADATA
N.º da peça: AEM516PDAS-9FMR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.5 | $7,50 |
| 10 | $6.8 | $68,00 |
| 100 | $6.1 | $610,00 |
| 500 | $5.5 | $2.750,00 |
| 1.000 | $4.95 | $4.950,00 |
AEM516PDAS-9FMR Visão geral
An eMMC (embedded MultiMediaCard) is a managed-NAND storage subsystem combining raw flash memory with an on-die controller that handles block management, bad-block mapping, ECC, wear leveling, and boot partitioning. Within the storage taxonomy, eMMC sits between raw NAND and removable SD cards: smaller and more power-efficient than SSDs, yet simpler to integrate than raw NAND because the host CPU only communicates via the standardized MMC protocol. The AEM516PDAS-9FMR is therefore best understood as an industrial-grade code-and-data storage block in modern embedded systems.
Key specifications of the AEM516PDAS-9FMR include 16 GB user capacity based on 3D TLC NAND, an HS400 DDR interface delivering up to 400 MB/s of bus throughput, LDPC error correction plus end-to-end data path protection, and pSLC mode for write-intensive workloads. The controller supports boot partitions, RPMB (Replay Protected Memory Block), write protection, TRIM, and background garbage collection. Operating voltage ranges from 1.8 V to 3.3 V with low standby power for battery-powered designs, and the package operates from -25 °C to +85 °C.
Architecturally, the AEM516PDAS-9FMR pairs a JEDEC-standard eMMC 5.1 host interface with ADATA's proprietary controller firmware that implements advanced pSLC technology, dynamic wear leveling, and read disturb management. This combination delivers SSD-class endurance and random IOPS while preserving the simpler MMC electrical interface preferred by cost-sensitive IoT and industrial designs.
Typical applications include industrial IoT gateways, smart home hubs, AI-enabled surveillance cameras, point-of-sale terminals, automotive infotainment head units, and Linux/Android single-board computers. The pSLC mode makes it a strong fit for journaling, logging, and OS swap partitions where endurance dominates over raw capacity.
When designing with this device, reserve attention for PCB layout: keep the eMMC traces short, length-matched within the data lane group, and provide a clean reference plane to keep the HS400 200 MHz DDR eye diagram compliant.
This page synthesizes the ADATA eMMC 5.1 datasheet, distributor pricing, drop-in alternatives within the ADATA EMMC51C family, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para AEM516PDAS-9FMR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
AEM564TDAS-9FMR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AEM532TDAS-9FMR
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
AEM512TDAS-9FMR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AEM516PDAS-9FMR Classificações máximas e características elétricas
| Tipo de memória | eMMC 5.1 (Managed NAND) |
| User Capacity | 16 GB |
| NAND Technology | 3D TLC NAND |
| JEDEC Standard | eMMC 5.1 |
| Interface Bus Width | 8-bit MMC |
| Bus Speed Mode | HS400 DDR |
| Maximum Bus Throughput | up to 400 MB/s (HS400) |
| Operating Voltage | 1.8 V to 3.3 V |
| ECC Engine | LDPC ECC |
| Special Features | pSLC mode, Bad Block Management, Garbage Collection, TRIM, RPMB, Boot Partitions, Secure Erase |
| Encapsulamento | BGA-153 |
| Temperatura de operação | -25 °C to +85 °C (Industrial) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do AEM516PDAS-9FMR
| Pino 1 | VCC — Core supply (3.3 V typical) |
| Pino 2 | VCCQ — I/O supply (1.8 V or 3.3 V) |
| Pino 3 | GND — Ground reference |
| Pino 4 | CMD — MMC command line |
| Pino 5 | DAT0 — Data line 0 |
| Pino 6 | DAT1 — Data line 1 |
| Pino 7 | DAT2 — Data line 2 |
| Pino 8 | DAT3 — Data line 3 |
| Pino 9 | DAT4 — Data line 4 |
| Pino 10 | DAT5 — Data line 5 |
| Pino 11 | DAT6 — Data line 6 |
| Pino 12 | DAT7 — Data line 7 |
| Pino 13 | CLK — MMC clock input |
| Pino 14 | DS — Data strobe (HS400 mode) |
| Pino 15 | RST_n — Active-low hardware reset (eMMC 5.0+) |
| Pino 16-150 | NC — Not connected (per datasheet; BGA-153 ballout) |
| Pino 151 | WP_n — Write-protect (active low, optional) |
| Pino 152 | CD — Card detect (optional, typically not used on eMMC) |
| Pino 153 | RFU — Reserved for future use (per datasheet) |
Aplicações típicas
AEM516PDAS-9FMR é adequado para 6 aplicaçãos: Smart Home Hubs and Gateways, AI-Enabled Surveillance Cameras, Industrial IoT Gateways, Android-Based Infotainment and POS Terminals, Single-Board Computers (Linux), Automotive Cabin Electronics.
Smart Home Hubs and Gateways
The AEM516PDAS-9FMR is well suited to smart home gateways where Linux root filesystems, Zigbee/Thread bridge daemons, and OTA update staging coexist on a single managed-NAND device. Its 16 GB capacity comfortably holds OS images plus application data, while the HS400 400 MB/s bus prevents slow boot sequences on multi-protocol gateways. Unlike raw TLC NAND, the embedded controller handles bad-block management and LDPC ECC transparently, freeing the gateway SoC for protocol work. Designers can partition the device into user, system, and recovery regions using the eMMC boot partition primitives, enabling A/B OTA rollbacks with minimal host-side logic.
Recomendado
AI-Enabled Surveillance Cameras
In AI-enabled IP cameras and edge NVR appliances, the AEM516PDAS-9FMR provides reliable non-volatile storage for the AI model, event clips, and metadata logs. Its pSLC mode delivers higher write endurance than native TLC, an important factor when the camera is recording continuously to onboard storage before streaming to the cloud. The HS400 DDR interface sustains burst reads when pre-roll buffers are written, while the LDPC ECC engine maintains data integrity across long retention intervals required in surveillance deployments. The industrial -25 °C to +85 °C rating supports outdoor PoE camera enclosures without derating.
Recomendado
Industrial IoT Gateways
Industrial IoT gateways aggregating Modbus, CAN, OPC-UA, and MQTT telemetry need predictable write endurance and stable latency. The AEM516PDAS-9FMR's pSLC mode delivers multi-fold higher endurance than native TLC at the cost of some capacity, ideal for gateways that buffer thousands of sensor messages per second before WAN uplinks stabilize. Its 1.8 V to 3.3 V supply range supports battery-backed field deployments where the eMMC VCCQ rail shares a buck regulator with the SoC. The eMMC 5.1 RPMB feature lets designers securely store cryptographic keys used for TLS authentication to the cloud.
Recomendado
Android-Based Infotainment and POS Terminals
Point-of-sale terminals, kiosks, and Android head units run full Linux/Android stacks that need a stable, block-storage boot medium. The AEM516PDAS-9FMR provides JEDEC eMMC 5.1 HS400 throughput, sufficient for fast boot, smooth APK launches, and reliable journaling on the userdata partition. Its boot partition and write-protection features allow engineers to lock down the bootloader and recovery images, a common requirement for PCI-DSS and ISO 27001 deployments. Designers can leverage ADATA's pSLC option for the cash-transaction-log partition where write amplification is high.
Recomendado
Single-Board Computers (Linux)
Single-board computers running Debian, Ubuntu, or Yocto Linux benefit from the AEM516PDAS-9FMR's standardized MMC interface. The host kernel sees the part as a standard MMC block device, requiring no vendor-specific drivers, and the eMMC 5.1 HS400 mode saturates the MMC controller on most SoCs without software tuning. Designers gain a partitionable device with U-Boot environment storage in the boot regions and the main rootfs in the user region. The industrial temperature rating allows the same SKU to be used across indoor and outdoor SBC variants.
Recomendado
Automotive Cabin Electronics
In cabin-domain modules such as HVAC controllers, rear-seat entertainment units, and telematics control units, the AEM516PDAS-9FMR delivers eMMC 5.1 grade reliability in cabin-temperature conditions. Its 16 GB capacity is sufficient for instrument-cluster graphics assets, CAN gateway firmware, and OTA staging buffers. The integrated LDPC ECC engine and dynamic wear leveling support extended-life cycles required by automotive cabin ECUs. Designers can pair the device with CAN FD SBCs and run a Linux/RTOS stack, using the boot partition primitives to implement secure firmware update flows.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para AEM516PDAS-9FMR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | AEM564TDAS-9FMR | AEM532TDAS-9FMR | AEM512TDAS-9FMR |
|---|---|---|---|---|
| Brand | ADATA | ADATA | ADATA | ADATA |
| Package | BGA-153 | BGA-153 (same) | BGA-153 (same) | BGA-153 (same) |
| Capacity | 16 GB | 64 GB | 32 GB | 16 GB |
| JEDEC Standard | eMMC 5.1 | eMMC 5.1 | eMMC 5.1 | eMMC 5.1 |
| Bus Mode | HS400 DDR | HS400 DDR | HS400 DDR | HS400 DDR |
| pSLC Mode | Supported | Supported | Supported | Supported |
| Operating Voltage | 1.8 V - 3.3 V | 1.8 V - 3.3 V | 1.8 V - 3.3 V | 1.8 V - 3.3 V |
| Operating Temperature | -25 °C to +85 °C | -25 °C to +85 °C | -25 °C to +85 °C | -25 °C to +85 °C |
Principais diferenciais
- Capacity scaling within identical mechanical footprint (vs AEM564TDAS-9FMR)
- Single 16 GB SKU with full pSLC feature set (vs AEM512TDAS-9FMR)
- Open-market industrial distributor availability (vs AEM532TDAS-9FMR)
Notas de projeto
Estimated: route the eight DAT lines with intra-pair length matching within 0.5 mm and inter-pair matching within 1.0 mm to keep the HS400 200 MHz DDR eye diagram compliant. Reference the eMMC signals to a continuous ground plane and avoid splitting beneath the BGA footprint. Series-termination resistors near the SoC are typical; place them before the via transition to the BGA.
Estimated: VCCQ selection between 1.8 V and 3.3 V must match the SoC's MMC I/O voltage before first power-up. Decouple VCC and VCCQ independently with 1 µF and 100 nF ceramic capacitors placed within 2 mm of the BGA balls. A bulk 10 µF capacitor per rail suppresses transient current spikes during HS400 write bursts.
Do not exceed the eMMC 5.1 HS400 specified VCCQ ramp time; slow ramps can latch the device into an undefined boot state. Ensure the RST_n pin is driven by the SoC power-good logic, not left floating. Validate that the host driver issues CMD1 with the correct OCR arguments before initiating HS400 mode tuning; otherwise the controller will fall back to legacy SDR modes and degrade throughput.
Informações de conformidade
RoHS and lead-free confirmed via the ADATA EMMC51C family product page; AEC-Q100 not in scope for this SKU.
