ATF22LV10C-10PU - 10ns CMOS PLD with 10 Macrocells | Microchip
N.º da peça: ATF22LV10C-10PU ✓ AtivoATF22LV10C-10PU Visão geral
An electrically erasable programmable logic device, or EEPROM PLD, combines a fixed logic architecture with nonvolatile configuration memory. The ATF22LV10C belongs to the broader PAL-compatible programmable logic hierarchy, where product terms, macrocells, registers, and fixed input/output assignments implement sum-of-products control logic. Its electrically erasable flash memory permits the programmed configuration to be rewritten during design updates or manufacturing revisions.
The headline operating specifications are a 10 ns device speed, 10 macrocells, and a 3.0 V to 5.5 V supply range. The 500-gate implementation can consolidate multiple gates, decoded state machines, interface controls, and fixed Boolean functions into one programmable device. Its low-power shutdown characteristic is particularly useful when individual logic sections must remain inactive during portions of the operating cycle.
The ATF22LV10C architecture follows the JEDEC 22V10-style assignment described for the family. Input signals feed the programmable logic array, while ten dedicated registers support sequential functions and clocked control. A dedicated clock input and output-enable control support registered outputs and board-level bus arbitration. This makes the device suitable for both combinational decoding and finite-state-machine implementations where deterministic timing and predictable pin assignments are important.
Typical uses include industrial control, data-acquisition interfaces, peripheral control, address decoding, keypad scanning, traffic sequencing, and compact embedded control logic. The device is particularly appropriate when a legacy programmable-logic design requires several gates, registers, or state-machine functions but does not justify implementing the equivalent logic in a microcontroller or FPGA.
Before layout, use the manufacturer pin-description table to assign every signal and preserve the standard 24-pin footprint. Pay particular attention to clock, output-enable, supply, ground, dedicated inputs, and I/O pins. Confirm timing against the system clock and I/O loading rather than relying only on the nominal 10 ns speed rating.
This page combines the family-level electrical characteristics, exact-ordering-code distinctions, same-footprint alternatives, and practical implementation guidance needed to determine whether the ATF22LV10C-10PU can retain its programmed logic function without changing the PCB.
Alternativas drop-in para ATF22LV10C-10PU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
ATF22LV10C-10PC
✅ Drop-InConsulte o preço
Ver ficha técnica →ATF22LV10C-10PI
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATF22LV10C-10PU Classificações máximas e características elétricas
| Device Type | Electrically Erasable Programmable Logic Device |
| Product Family | ATF22LV10C |
| Speed Grade | 10 ns |
| Macrocells | 10 macrocells |
| Registers | 10 registers |
| Equivalent Gate Capacity | 500 gates |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Programming Technology | Electrically erasable flash memory |
| Power-Down Standby Current | 10 µA typical |
| Logic Family | CMOS |
| User I/O Count | 10 pins |
| Device Pin Count | 24 pins |
| Encapsulamento | 24-pin PDIP |
| Tipo de montagem | Through-hole |
| Programmable Architecture | PAL-compatible 22V10-style architecture |
Guia de Configuração de Pinos do ATF22LV10C-10PU 24-pin pdip
Configuração de pinos para ATF22LV10C-10PU (pacote 24-pin pdip). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATF22LV10C-10PU.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATF22LV10C-10PU é adequado para 6 aplicaçãos: Industrial State-Machine Control, Data-Acquisition Interface Control, Peripheral Address Decoding, Keypad and Human-Interface Control, Motor and Sequencer Logic, Legacy Control-System Consolidation.
Industrial State-Machine Control
The ATF22LV10C-10PU is well suited to compact sequential control because it provides 10 macrocells and 10 registers within a single 10 ns programmable-logic device. Its registered outputs can implement state transitions, interlocks, and sequencing without dividing the logic across multiple gate packages. The 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V system rails, while the 10 µA typical power-down current allows controllers to disable the logic during inactive periods. Use the manufacturer clock and output-enable assignments exactly as specified, and validate setup and hold timing against the actual system clock and I/O loading.
Recomendado
Data-Acquisition Interface Control
ATF22LV10C-10PU can consolidate the address decoding, latch control, and status sequencing surrounding a data-acquisition system. Ten dedicated registers support clocked control functions, while the 10 ns speed grade provides margin for combinational decode paths and registered interface signals. The 500-gate capacity is useful for merging control logic that would otherwise occupy several discrete gate packages. Keep external analog and high-speed data paths physically separate, use short clock and output-enable routes, and verify setup timing against the converter and acquisition controller requirements before relying on the nominal propagation rating.
Recomendado
Peripheral Address Decoding
The ATF22LV10C-10PU can decode multiple peripheral addresses and generate qualified control strobes within a compact legacy logic design. Its 10 macrocells and 10 registers provide enough resources for bus decoding, register-latch behavior, and combinational qualification of several control signals. The 3.0 V to 5.5 V operating range permits use in mixed-voltage equipment when interface levels are compatible, and electrically erasable flash allows the decode map to be revised during production. Route clock and enable signals away from switching nodes, observe required output timing, and confirm unused pins according to the manufacturer's pin table.
Recomendado
Keypad and Human-Interface Control
A 10 ns programmable logic device can handle keypad scanning, debounce control, display multiplexing, and keypad-to-system signal translation without a processor interrupt overhead. The ATF22LV10C-10PU's 10 registers allow scan-state and output-latch functions to share one programmable device, while its 500-gate capacity supports multiple Boolean decoding paths. The user-controlled power-down feature is helpful in portable or intermittently powered interfaces because the datasheet specifies 10 µA typical standby current. Validate scan timing, contact-bounce assumptions, and display update rates in the programmed equations rather than treating the nominal 10 ns rating as the complete system timing budget.
Recomendado
Motor and Sequencer Logic
The ATF22LV10C-10PU can implement deterministic step sequencing, direction decoding, limit-condition interlocks, and output qualification in compact motion-control equipment. Registered outputs help organize transitions into discrete states, while the 10 macrocells can combine the Boolean conditions needed for each transition. Because the device operates from 3.0 V to 5.5 V, it can sit beside a compatible 3.3 V controller, although motor-driver signals must remain within the device's specified I/O limits. Add protection appropriate to the external motor environment, isolate noisy power paths from clock traces, and verify every state and fault condition through simulation.
Recomendado
Legacy Control-System Consolidation
ATF22LV10C-10PU is useful when replacing dispersed gates, flip-flops, and combinational logic in a legacy control board while retaining the established 24-pin PDIP footprint. Its 10 macrocells, 10 registers, and 500-gate capacity can consolidate several small logic functions, while the electrically erasable configuration supports design revisions without a separate programmable device. The 10 ns speed rating supports timing closure in many control paths, but engineers should compare the original device's propagation delay and output behavior against the ATF22LV10C datasheet. Preserve the standard clock, enable, input, and I/O assignments, and validate both active and power-down states.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATF22LV10C-10PU — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATF22LV10C-10PC | ATF22LV10C-10PI |
|---|---|---|---|
| Package | 24-pin PDIP | 24-pin PDIP | 24-pin PDIP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Device Type | Electrically Erasable Programmable Logic Device | Electrically Erasable Programmable Logic Device | Electrically Erasable Programmable Logic Device |
| Speed Grade | 10 ns | 10 ns | 10 ns |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Registers | 10 registers | 10 registers | 10 registers |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Power-Down Standby Current | 10 µA typical | 10 µA typical | 10 µA typical |
| Programming Technology | Electrically erasable flash memory | Electrically erasable flash memory | Electrically erasable flash memory |
Principais diferenciais
- Combines sequential and combinational resources in one low-voltage PLD (vs ATF22LV10C-10PC)
- Supports low-power system control through user-controlled power-down (vs ATF22LV10C-10PI)
- Maintains the established 24-pin PDIP control-logic footprint (vs ATF22LV10C-10PC)
Notas de projeto
Treat the clock as a dedicated high-fidelity route. Keep it short, avoid branching it into unnecessary loads, and place any required termination according to the board's clock architecture. The nominal 10 ns speed is a device timing parameter rather than a guarantee for every external path, so setup time, hold time, propagation delay, output loading, and the receiving device's requirements must all be included in the timing analysis.
Preserve the manufacturer-standard 24-pin PDIP footprint when repairing or updating an existing board. Check clock, output-enable, dedicated inputs, I/O pins, VCC, and ground assignments against the ATF22LV10C pin-description table before programming. A mechanically similar 22V10 socketed device is not necessarily a drop-in substitute because memory technology, timing, power-down behavior, and some electrical characteristics can differ.
Operate the ATF22LV10C-10PU only within its documented 3.0 V to 5.5 V supply range. Place the required supply bypass capacitance close to the device's VCC and ground pins, and keep switching-node currents away from the PLD's supply path. The 10 µA typical standby current applies to the device's power-down condition; total board standby consumption must be calculated from external loads, pull resistors, and connected logic.
Do not treat -10PC, -10PI, and -10PU as unrestricted procurement aliases. Their ordering codes distinguish temperature grade, and the programmed configuration must also be compatible with the replacement. Before substitution, compare the complete suffix, operating-temperature requirements, pin assignment, programmed equations, clock configuration, output-enable behavior, and timing assumptions. In legacy systems, also test power-up, power-down, and unused-pin states.
Informações de conformidade
The ATF22LV10C-10PU is a programmable logic IC and is not an AEC-Q100 automotive-qualified device. Environmental and finish compliance are not stated in the cited family documentation.