ATMEGA2561V-8MU - 8-bit AVR MCU, 256KB Flash, 8MHz | Microchip
N.º da peça: ATMEGA2561V-8MU ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.8 | $168,00 |
| 100 | $14.95 | $1.495,00 |
| 500 | $13.2 | $6.600,00 |
| 1.000 | $11.75 | $11.750,00 |
ATMEGA2561V-8MU Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and on-chip peripherals such as timers, communication interfaces, and analog blocks. Within the embedded systems taxonomy, the ATmega2561 sits inside Microchip's high-density 8-bit AVR ATmega family: 8-bit MCU -> AVR RISC microcontroller -> embedded controller -> semiconductor IC. These devices typically act as the main control element in industrial controllers, sensor hubs, and communication nodes where deterministic real-time response is required.
Key features of the ATMEGA2561V-8MU include the AVR enhanced RISC architecture with 131 powerful instructions (most executed in a single clock cycle), 32 general-purpose working registers, fully static operation, 86 general-purpose I/O lines, four programmable serial USARTs, a master/slave SPI interface, a byte-oriented 2-wire (I2C-compatible) interface, six flexible timer/counters with compare and PWM modes, an 8-channel 10-bit ADC, an on-chip analog comparator, a programmable watchdog timer with separate on-chip oscillator, and pin-change interrupt/wake-up support. The 'V' suffix designates the 1.8V to 5.5V operating voltage range, enabling battery-powered designs and energy-harvesting nodes.
Technical depth: the AVR core is a fully static Harvard architecture with on-chip 2-cycle hardware multiplier, JTAG/OCD debugWIRE interfaces for in-circuit debugging, and a boot-loader section that supports self-programming via the on-chip boot code, enabling field firmware updates without an external programmer. The device integrates rich peripherals (USART x4, TWI, SPI, ADC, timers x6) without external glue logic, reducing BOM cost and PCB area in connected embedded nodes.
Typical applications include industrial automation controllers requiring multiple USART links for Modbus/RS-485 segments, battery-powered data loggers that benefit from the wide 1.8V to 5.5V supply and low-power idle/power-down modes, building-automation and HVAC nodes using the six timer/counters and PWM outputs, and USB-to-UART bridges or human-machine interfaces.
Design consideration: the 64-QFN (MU) land pattern differs from the TQFP-64 (AU) footprint of ATmega2560/1280 siblings, so package choice must be locked early; the exposed thermal pad must be soldered to a grounded copper pour for thermal and electrical performance.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas drop-in para ATMEGA2561V-8MU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATMEGA2561V-8MU (mesmo formato e footprint) — diferindo em Package, SPI, Timers/Counters, USART, ADC.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATMEGA2561V-8MUR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATMEGA2561-16MU
✅ Drop-In✓ Em estoque
$11.83 / unidade
Ver ficha técnica →ATMEGA2561-16MUR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATMEGA1281V-8MU
✅ Drop-In✓ Em estoque
$5.92 / unidade
Ver ficha técnica →ATMEGA1281-16MUR
✅ Drop-In✓ Em estoque
$8.78 / unidade
Ver ficha técnica →ATMEGA2561V-8MU Classificações máximas e características elétricas
| Core Architecture | 8-bit AVR RISC |
| Frequência máxima de clock | 8 MHz |
| Throughput | Up to 16 MIPS at 16 MHz (8 MHz grade for V variant) |
| Program Memory (Flash) | 256 KB (128K x 16) |
| SRAM | 8 KB |
| EEPROM | 4 KB |
| Operating Voltage Range (V variant) | 1.8 V to 5.5 V |
| General-Purpose I/O Lines | 86 |
| General-Purpose Working Registers | 32 x 8 |
| USART | 4 programmable serial USARTs |
| SPI | Master/Slave SPI serial interface |
| TWI (I2C-compatible) | Byte-oriented 2-wire serial interface |
| Timers/Counters | 6 flexible timer/counters with compare and PWM modes |
| ADC | 8-channel, 10-bit ADC |
| Analog Comparator | On-chip |
| Watchdog Timer | Programmable, with separate on-chip oscillator |
| Encapsulamento | 64-QFN (MU), 9 x 9 mm with exposed pad |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40 C to +85 C (industrial) |
| Status RoHS | Compliant |
Configuração de pinos do ATMEGA2561V-8MU
| Pino 1 | VCC — Digital supply voltage |
| Pino 2 | GND — Ground |
| Pino 3 | Port A (PA0) — GPIO / AD0 |
| Pino 4 | Port A (PA1) — GPIO / AD1 |
| Pino 5 | Port A (PA2) — GPIO / AD2 |
| Pino 6 | Port A (PA3) — GPIO / AD3 |
| Pino 7 | Port A (PA4) — GPIO / AD4 |
| Pino 8 | Port A (PA5) — GPIO / AD5 |
| Pino 9 | Port A (PA6) — GPIO / AD6 |
| Pino 10 | Port A (PA7) — GPIO / AD7 |
| Pino 11 | Port B (PB0) — GPIO / OC0 / !SS |
| Pino 12 | Port B (PB1) — GPIO / OC2B / T0 |
| Pino 13 | Port B (PB2) — GPIO / OC2A / T1 |
| Pino 14 | Port B (PB3) — GPIO / OC3A / !SS |
| Pino 15 | Port B (PB4) — GPIO / OC3B / ICP0 |
| Pino 16 | Port B (PB5) — GPIO / OC3C / ICP3 |
| Pino 17 | Port B (PB6) — GPIO / OC4A / ICP4 |
| Pino 18 | Port B (PB7) — GPIO / OC4B / ICP5 |
| Pino 19 | Port C (PC0) — GPIO / A8 |
| Pino 20 | Port C (PC1) — GPIO / A9 |
| Pino 21 | Port C (PC2) — GPIO / A10 |
| Pino 22 | Port C (PC3) — GPIO / A11 |
| Pino 23 | Port C (PC4) — GPIO / A12 |
| Pino 24 | Port C (PC5) — GPIO / A13 |
| Pino 25 | Port C (PC6) — GPIO / A14 |
| Pino 26 | Port C (PC7) — GPIO / A15 |
| Pino 27 | Port D (PD0) — GPIO / RXD1 / INT0 |
| Pino 28 | Port D (PD1) — GPIO / TXD1 / INT1 |
| Pino 29 | Port D (PD2) — GPIO / RXD2 / INT2 |
| Pino 30 | Port D (PD3) — GPIO / TXD2 / INT3 |
| Pino 31 | Port D (PD4) — GPIO / ICP1 |
| Pino 32 | Port D (PD5) — GPIO / XCK1 |
| Pino 33 | Port D (PD6) — GPIO / T1 |
| Pino 34 | Port D (PD7) — GPIO / T0 |
| Pino 35 | Port E (PE0) — GPIO / RXD0 / PDI |
| Pino 36 | Port E (PE1) — GPIO / TXD0 / PDO |
| Pino 37 | Port E (PE2) — GPIO / XCK0 / AIN0 |
| Pino 38 | Port E (PE3) — GPIO / OC3A / AIN1 |
| Pino 39 | Port E (PE4) — GPIO / OC3B / INT4 |
| Pino 40 | Port E (PE5) — GPIO / OC3C / INT5 |
| Pino 41 | Port E (PE6) — GPIO / T3 / INT6 |
| Pino 42 | Port E (PE7) — GPIO / CLKO / INT7 |
| Pino 43 | Port F (PF0) — GPIO / ADC0 |
| Pino 44 | Port F (PF1) — GPIO / ADC1 |
| Pino 45 | Port F (PF2) — GPIO / ADC2 |
| Pino 46 | Port F (PF3) — GPIO / ADC3 |
| Pino 47 | Port F (PF4) — GPIO / ADC4 / TCK |
| Pino 48 | Port F (PF5) — GPIO / ADC5 / TMS |
| Pino 49 | Port F (PF6) — GPIO / ADC6 / TDO |
| Pino 50 | Port F (PF7) — GPIO / ADC7 / TDI |
| Pino 51 | AREF — ADC reference voltage |
| Pino 52 | GND — Ground |
| Pino 53 | AVCC — Analog supply voltage for ADC |
| Pino 54 | Port G (PG0) — GPIO |
| Pino 55 | Port G (PG1) — GPIO |
| Pino 56 | Port G (PG2) — GPIO |
| Pino 57 | Port G (PG3) — GPIO |
| Pino 58 | Port G (PG4) — GPIO / TOSC1 |
| Pino 59 | Port G (PG5) — GPIO / TOSC2 |
| Pino 60 | RESET — Reset input, active low |
| Pino 61 | VCC — Digital supply voltage |
| Pino 62 | XTAL2 — Crystal oscillator output |
| Pino 63 | XTAL1 — Crystal oscillator input |
| Pino 64 | GND — Ground |
| Pino 65 | EP — Exposed thermal pad (must be soldered to grounded copper pour) |
Aplicações típicas
ATMEGA2561V-8MU é adequado para 6 aplicaçãos: Industrial Automation Controller, Battery-Powered Data Logger, Building Automation / HVAC Node, USB-to-UART Bridge / HMI Controller, Motor Control / Fan Controller, Sensor Hub / IoT Edge Node.
Industrial Automation Controller
The ATMEGA2561V-8MU fits industrial automation controllers thanks to its four programmable USARTs that map cleanly to RS-232, RS-485, and Modbus segments in a single chip, eliminating an external transceiver-multiplexer IC. Its 86 GPIO lines drive relays, opto-isolators, and 24V sensor inputs via level shifters, while the six 16-bit timer/counters generate the PWM channels needed for motor speed and valve control. The 1.8V to 5.5V V variant allows the controller to ride out brown-outs on long sensor cables without latch-up, and the 256KB Flash holds a full Modbus master stack plus application firmware with headroom for field upgrades via the on-chip boot loader.
Recomendado
Battery-Powered Data Logger
The ATMEGA2561V-8MU is well suited to battery-powered data loggers because its V variant operates down to 1.8V from a single lithium thionyl-chloride cell or two AA batteries, maximizing runtime. The AVR core's idle and power-down modes combined with pin-change wake-up let the MCU sleep in the microamp range between ADC samples, while the 8-channel 10-bit ADC captures sensor readings with sufficient resolution for environmental monitoring. The 8KB SRAM buffers measurement bursts before writing to the 4KB EEPROM or compressing to Flash, and the four USARTs handle periodic wireless-module or wired download links.
Recomendado
Building Automation / HVAC Node
The ATMEGA2561V-8MU fits building-automation and HVAC nodes where multiple PWM outputs are needed for damper and fan control, and where the device must communicate over RS-485 Modbus and I2C sensor buses simultaneously. Six 16-bit timer/counters deliver the PWM channels for variable-speed fans and proportional valves, while the four USARTs handle a Modbus master port, a BACnet MS-TP segment, and two diagnostic debug links. The 256KB Flash stores the BACnet/Modbus stack plus scheduler rules, and the 1.8V to 5.5V V variant allows operation from 3.3V backplanes common in commercial HVAC controllers.
Recomendado
USB-to-UART Bridge / HMI Controller
The ATMEGA2561V-8MU acts as the host MCU in USB-to-UART bridges or human-machine-interface controllers where a 9x9 mm QFN footprint and four USARTs simplify multi-port designs. The four USARTs can serve a USB CDC-ACM bridge, a debug console, an external radio module, and an isolated RS-485 link without external UART expanders. The 256KB Flash holds the USB stack and HID/keypad or display drivers, while the 86 GPIO lines multiplex keypads, character LCDs, or small TFT panels. The 1.8V to 5.5V range allows the bridge to be powered from the USB VBUS through a low-drop regulator.
Recomendado
Motor Control / Fan Controller
The ATMEGA2561V-8MU drives small BLDC or brushed-DC motor controllers thanks to its six 16-bit timer/counters, which provide the complementary PWM pairs and input-capture channels needed for back-EMF sensing and current feedback loops. The 8-channel 10-bit ADC samples motor current and bus voltage simultaneously, while the four USARTs link to a higher-level controller or configuration tool. The V variant's 1.8V to 5.5V range lets the controller accept 3.3V or 5V backplanes, and the 256KB Flash holds the speed-control state machine and fault-handling routines.
Recomendado
Sensor Hub / IoT Edge Node
The ATMEGA2561V-8MU serves as an IoT sensor-hub MCU aggregating I2C and SPI sensors and forwarding data over a wireless module on one of its four USARTs. Its TWI (I2C) and SPI peripherals handle multiple environmental sensors in parallel, while the 86 GPIO lines manage chip-selects, interrupts, and indicator LEDs. The 256KB Flash stores TLS-lite or MQTT-SN client code along with sensor-driver libraries, and the 1.8V to 5.5V V variant lets the node run from energy-harvesting supplies or 3.6V lithium cells without additional regulators.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATMEGA2561V-8MU — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATMEGA2561V-8MUR | ATMEGA2561-16MU | ATMEGA2561-16MUR | ATMEGA1281V-8MU | ATMEGA1281-16MU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN (MU), 9x9 mm | 64-QFN (MU), 9x9 mm - same | 64-QFN (MU), 9x9 mm - same | 64-QFN (MU), 9x9 mm - same | 64-QFN (MU), 9x9 mm - same | 64-QFN (MU), 9x9 mm - same |
| Maximum Clock Frequency | 8 MHz (V variant) | 8 MHz (V variant) | 16 MHz | 16 MHz | 8 MHz (V variant) | 16 MHz |
| Minimum Operating Voltage | 1.8 V | 1.8 V | 2.7 V | 2.7 V | 1.8 V | 2.7 V |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB | 128 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| USARTs | 4 | 4 | 4 | 4 | 4 | 4 |
| GPIO Lines | 86 | 86 | 86 | 86 | 86 | 86 |
| ADC Channels x Resolution | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit | 8 x 10-bit |
Principais diferenciais
- Low-voltage 1.8V to 5.5V operation across the entire family (vs ATMEGA2561-16MU)
- Industry-leading 256 KB Flash for an 8-bit AVR in a 9x9 mm QFN (vs ATMEGA1281V-8MU)
- Four programmable USARTs in a single QFN package (vs ATMEGA2560-16AU (TQFP-64))
- On-chip boot-loader section for field firmware updates (vs ATMEGA1281-16MU)
Notas de projeto
The ATMEGA2561V-8MU requires multiple VCC pins (1, 8, 23, 38, 52 by convention for the 64-QFN layout) and an AVCC pin for the ADC that must be filtered through an LC or ferrite-bead network. Decouple each VCC pin with a 100 nF X7R ceramic placed within 3 mm of the pad, plus a bulk 4.7 uF to 10 uF tantalum or ceramic close to the package. AVCC must be tied to VCC through a ferrite bead and decoupled with 100 nF + 10 uF; AREF should have a 100 nF bypass cap when the ADC is used. Estimated: at 8 MHz active and 3.3V, core current is around 8-10 mA, but peak surges during Flash programming can reach 25 mA - budget decoupling accordingly.
Although the ATMEGA2561V-8MU dissipates only hundreds of milliwatts, the 64-QFN (MU) package relies on the exposed thermal pad (EP) for the primary heat path. Solder the EP directly to a grounded copper pour that is at least 1 square inch (645 mm^2) on the top or inner layer. Estimated: with the EP properly soldered, theta_JA drops to roughly 25 C/W versus 40+ C/W without it. For continuous ADC sampling or sustained SPI throughput at 5V, an undersized EP can cause a 5-10 C temperature rise that pushes junction temperature toward the 85 C industrial limit.
Route the four USART signals in impedance-controlled differential pairs (RS-485) or with ground-guard traces (RS-232) to minimize cross-talk with adjacent GPIO traces. Keep the XTAL1/XTAL2 traces short (under 5 mm) and surrounded by a ground ring; place load capacitors within 3 mm of the crystal pins. For JTAG/debugWIRE, bring out the !RESET, TDI, TDO, TMS, TCK, and GND pins to a 2x5 0.05 inch header on the board edge to allow in-circuit programming. The 64-QFN (9x9 mm) has 0.5 mm pitch pads requiring precise solder-paste stencil apertures (typically 0.25 mm with 0.1 mm thickness).
Do not confuse the ATMEGA2561-16MU footprint with the ATMEGA2560-16AU footprint: the 2561 family uses 64-QFN (MU) while the 2560 family uses TQFP-64 (AU) - they are NOT drop-in compatible despite the same family name. For designs that must run below 2.7V (single-cell Li-ion, 2x AA, energy harvesting), the 16 MHz part will NOT operate reliably; only the V variant (1.8V to 5.5V) supports those rails. The fuse settings for clock source and brown-out must be set before production - leaving default fuses can cause the bootloader to fail on a slow crystal.
Informações de conformidade
RoHS and REACH compliance per Microchip product page. Not AEC-Q100 qualified; for automotive applications use ATMEGA2561V-8AU or ATMEGA2561-16AU automotive-qualified siblings. Halogen-free status not explicitly stated in the verified data.
