ATMEGA32C1-15MZ - 32KB Flash CAN 8-bit AVR MCU | Microchip
N.º da peça: ATMEGA32C1-15MZ ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.42 | $5,42 |
| 10 | $4.88 | $48,80 |
| 100 | $4.31 | $431,00 |
| 500 | $3.85 | $1.925,00 |
| 1.000 | $3.42 | $3.420,00 |
ATMEGA32C1-15MZ Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. Within the broader taxonomy, the ATMEGA32C1 belongs to the 8-bit MCU family -> AVR RISC architecture -> automotive/industrial CAN-enabled microcontrollers -> embedded computing semiconductor. It executes one instruction per clock cycle, which gives it significantly higher throughput per MHz than traditional CISC 8-bit architectures. This category of MCU is used in applications requiring deterministic real-time control, on-chip communication peripherals (CAN, LIN, SPI, UART), and low power consumption.
Key features of the ATMEGA32C1-15MZ include an integrated CAN 2.0A/B controller, two flexible timer/counters with PWM and capture, an analog comparator, a 10-bit ADC, and an internal 16 MHz calibrated oscillator. The device supports 2.7V to 5.5V operation and is qualified to the automotive AEC-Q100 standard (-MZ suffix indicates automotive temperature grade -40C to +125C).
The AVR Harvard architecture provides separate program and data buses, allowing instruction fetch and data access to occur in the same clock cycle. The 32 KB of self-programmable Flash with read-while-write capability supports in-field firmware updates via the CAN interface. The integrated CAN module eliminates the need for an external CAN controller, reducing BOM cost and PCB area for networked embedded designs.
Typical applications include automotive body control modules, CAN node endpoints, HVAC controllers, industrial sensor nodes, and LIN/CAN gateway devices. In these systems, the ATMEGA32C1-15MZ serves as the main processing unit that handles sensor acquisition, drives actuators, and participates in vehicle network communication.
When designing with this MCU, ensure that the CAN bus transceiver (e.g., MCP2551 or TJA1050) is selected to match the bus speed and provide required ESD protection. Decoupling capacitors of 100 nF and 10 uF should be placed close to VCC pins, and an external crystal is not required since the internal oscillator is factory-calibrated.
This page synthesizes distributor pricing, drop-in AVR alternatives, and practical CAN node design guidance not consolidated in a single place in the manufacturer datasheet, providing engineering context for component selection.
Alternativas drop-in para ATMEGA32C1-15MZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATMEGA32C1-15MZ (mesmo formato e footprint) — diferindo em ADC, EEPROM, Program Memory Size, SRAM, Mounting Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATMEGA32C1-15AZ
✅ Drop-In✓ Em estoque
$2.95 / unidade
Ver ficha técnica →ATMEGA16M1-15MZ
✅ Drop-In✓ Em estoque
$2.58 / unidade
Ver ficha técnica →ATMEGA64C1-15MZ
✅ Drop-In✓ Em estoque
$1.62 / unidade
Ver ficha técnica →ATMEGA32C1-15MD
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATMEGA32M1-15MZ
✅ Drop-In✓ Em estoque
$3.98 / unidade
Ver ficha técnica →ATMEGA32C1-15MZ Classificações máximas e características elétricas
| Program Memory Size | 32 KB (16K x 16) Flash |
| RAM Size | 2 KB |
| EEPROM Size | 1 KB |
| CPU Core | AVR 8-bit RISC |
| Maximum Clock Speed | 16 MHz |
| Number of I/O Lines | 27 |
| Number of General-Purpose Registers | 32 |
| Instruction Set Size | 131 instructions |
| ADC | 10-bit, integrated |
| Operating Voltage | 2.7 V to 5.5 V |
| Temperatura de operação | -40C to +125C (automotive grade) |
| Integrated CAN Controller | Yes (CAN 2.0A/B) |
| Encapsulamento / Caixa | 32-TQFP |
| Tipo de montagem | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Status RoHS | Compliant |
| Oscillator Type | Internal |
Configuração de pinos do ATMEGA32C1-15MZ
| Pino 1 | PD3 — Port D bit 3 (digital I/O, INT1) |
| Pino 2 | PD4 — Port D bit 4 (digital I/O) |
| Pino 3 | GND — Ground |
| Pino 4 | VCC — Supply voltage 2.7V-5.5V |
| Pino 5 | GND — Ground |
| Pino 6 | VCC — Supply voltage |
| Pino 7 | PB0 — Port B bit 0 (digital I/O, SS) |
| Pino 8 | PB1 — Port B bit 1 (digital I/O, SCK) |
| Pino 9 | RESET — Reset input, active low |
| Pino 10 | VCC — Supply voltage |
| Pino 11 | GND — Ground |
| Pino 12 | XTAL1 — Crystal input or external clock |
| Pino 13 | XTAL2 — Crystal output |
| Pino 14 | PD5 — Port D bit 5 (digital I/O) |
| Pino 15 | PD6 — Port D bit 6 (digital I/O) |
| Pino 16 | PD7 — Port D bit 7 (digital I/O) |
| Pino 17 | PB2 — Port B bit 2 (digital I/O, MOSI) |
| Pino 18 | PB3 — Port B bit 3 (digital I/O, MISO) |
| Pino 19 | PB4 — Port B bit 4 (digital I/O) |
| Pino 20 | PB5 — Port B bit 5 (digital I/O, OC1A) |
| Pino 21 | PB6 — Port B bit 6 (digital I/O, OC1B) |
| Pino 22 | PB7 — Port B bit 7 (digital I/O, OC2A) |
| Pino 23 | PC0 — Port C bit 0 (analog input, ADC0) |
| Pino 24 | PC1 — Port C bit 1 (analog input, ADC1) |
| Pino 25 | PC2 — Port C bit 2 (analog input, ADC2) |
| Pino 26 | PC3 — Port C bit 3 (analog input, ADC3) |
| Pino 27 | PC4 — Port C bit 4 (analog input, ADC4) |
| Pino 28 | PC5 — Port C bit 5 (analog input, ADC5) |
| Pino 29 | CANTX — CAN transmit output |
| Pino 30 | CANRX — CAN receive input |
| Pino 31 | GND — Ground |
| Pino 32 | AVCC — Analog supply voltage |
Aplicações típicas
ATMEGA32C1-15MZ é adequado para 6 aplicaçãos: Automotive Body Control Module, CAN Sensor Node Endpoint, Industrial HVAC Controller, Automotive Door/Window Module, CAN-to-UART Bridge Gateway, Battery Management CAN Slave.
Automotive Body Control Module
The ATMEGA32C1-15MZ fits automotive body control modules that aggregate switch inputs, drive lamps and motors, and report status over CAN. Its integrated CAN 2.0A/B controller removes the need for an external CAN IC, while the 32 KB Flash with read-while-write supports OTA-style firmware updates through the CAN bus. The 27 GPIO lines provide ample headroom for switch scanning, LED PWM dimming, and motor half-bridge control. AEC-Q100 automotive temperature grade (-40C to +125C) ensures reliable operation in cabin and under-hood environments with cranking transients handled by internal brown-out detection settable down to 2.7 V.
Recomendado
CAN Sensor Node Endpoint
For distributed CAN sensor nodes (pressure, temperature, position) the ATMEGA32C1-15MZ integrates the CAN MAC layer directly, so designers need only add a CAN transceiver (MCP2551 or TJA1050) and the sensor front-end. The 10-bit ADC samples analog sensor outputs, while the 16 MHz internal oscillator eliminates an external crystal, reducing BOM cost and PCB area. The 32 KB Flash accommodates CANopen or J1939 protocol stacks plus application logic, and the 1 KB EEPROM stores calibration constants and node-ID. Per the datasheet, the internal oscillator is factory-calibrated to within +/-2% across voltage and temperature, sufficient for CAN bit timing at 125-500 kbit/s.
Recomendado
Industrial HVAC Controller
In industrial HVAC control the ATMEGA32C1-15MZ drives triacs for fan/blower speed regulation and reads temperature/pressure sensors for closed-loop control. The two flexible 16-bit timer/counters provide hardware PWM channels for triac phase-angle control or DC motor PWM, freeing the CPU from interrupt overhead. The integrated CAN port connects the HVAC unit to a building automation network (BACnet-over-CAN or vendor protocols), enabling centralized scheduling and diagnostics. The 2.7 V to 5.5 V operating range accommodates 24 V industrial rails regulated down to 5 V, and the 27 GPIO handle keypad input, LCD drive, and status LEDs.
Recomendado
Automotive Door/Window Module
The ATMEGA32C1-15MZ serves automotive door modules controlling window lift, mirror adjust, and central locking. Its automotive AEC-Q100 grade and 16 MHz AVR throughput provide real-time response for switch debouncing and motor direction control via H-bridge drivers. The integrated CAN controller links the door module to the body control network, while 27 GPIOs interface to window switches, mirror motors, and LED indicators. The 32 KB Flash supports door-zone-specific calibration (anti-pinch algorithms) and the 2 KB SRAM is sufficient for ramp-up/ramp-down motion profiles computed in real time.
Recomendado
CAN-to-UART Bridge Gateway
When bridging a CAN bus to a legacy UART-based sub-system the ATMEGA32C1-15MZ acts as a transparent gateway with its hardware CAN module and on-chip USART. Firmware in the 32 KB Flash implements message filtering, ID remapping, and protocol translation. The integrated 16 MHz core processes CAN messages at full bus speed (1 Mbit/s) without bottlenecks, and the 1 KB EEPROM stores gateway configuration. The TQFP-32 surface-mount package enables compact gateway PCBs suitable for retrofit industrial panels.
Recomendado
Battery Management CAN Slave
In modular battery management systems the ATMEGA32C1-15MZ functions as a CAN slave reporting per-cell voltage and temperature to a master BMS. The 10-bit ADC reads cell voltages through a multiplexer, while the integrated CAN controller publishes state-of-charge messages on the bus. The 32 KB Flash fits SAE J1939 or CANopen battery profiles plus application code, and the 2 KB SRAM buffers diagnostic messages. The wide 2.7-5.5 V supply range supports 12 V and 24 V battery packs with linear regulation, while the 27 GPIOs interface to cell-balancing FETs and temperature sensors.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATMEGA32C1-15MZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATMEGA32C1-15AZ | ATMEGA16M1-15MZ | ATMEGA64C1-15MZ |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP | 32-TQFP - same | 32-TQFP - same | 32-TQFP - same |
| Flash Memory | 32 KB | 32 KB | 16 KB | 64 KB |
| RAM Size | 2 KB | 2 KB | 1 KB | 4 KB |
| Integrated CAN Controller | Yes (CAN 2.0A/B) | Yes | Yes | Yes |
| Maximum Clock Speed | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Operating Temperature | -40C to +125C (automotive) | -40C to +85C (industrial) | -40C to +125C (automotive) | -40C to +125C (automotive) |
| AEC-Q100 Qualified | Yes (MZ suffix) | No (AZ industrial) | Yes | Yes |
Principais diferenciais
- Integrated CAN 2.0A/B controller on-chip (vs ATMEGA328PB-MNR)
- AEC-Q100 automotive temperature grade (-40C to +125C) (vs ATMEGA32C1-15AZ)
- 32 KB Flash with read-while-write support (vs ATMEGA16M1-15MZ)
Notas de projeto
Place a 100 nF decoupling capacitor as close as possible to each VCC/GND pin pair, with a bulk 10 uF tantalum or ceramic cap on the main supply rail. The ATmega32C1 has multiple VCC/GND pairs (pins 4/3, 6/5, 10/11) that must each be bypassed to maintain stable operation during CAN bus switching transients. Brown-out detection should be enabled via fuses with a threshold appropriate for automotive cranking profiles.
Route the CANTX and CANRX traces as a differential pair with controlled 120-ohm impedance, and place the MCP2551 transceiver within 50 mm of the MCU CAN pins to minimize EMI susceptibility. Keep CAN traces away from switching power nodes and route the ground return directly under the differential pair. Add a split-ferrite bead on the CAN supply if bus isolation is required.
Do not omit the external CAN transceiver - the ATmega32C1 integrates only the CAN MAC layer and cannot drive the physical bus directly. A common pitfall is forgetting that the internal 16 MHz oscillator, while calibrated, may require software trim for CAN bit timing at 1 Mbit/s; use the CAN baud-rate register settings from the datasheet's example tables rather than theoretical calculations.
Informações de conformidade
AEC-Q100 qualified per MZ suffix designation in Microchip ordering code. RoHS and REACH compliant per Microchip product page. Halogen-free status not explicitly stated in provided data.
