ATSAMD20G15A-ANT - 48MHz Cortex-M0+ MCU, 32KB Flash | TQFP-48 | Microchip
N.º da peça: ATSAMD20G15A-ANT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.55 | $25,50 |
| 100 | $2.21 | $221,00 |
| 500 | $1.93 | $965,00 |
| 1.000 | $1.68 | $1.680,00 |
ATSAMD20G15A-ANT Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (flash), working memory (SRAM), and programmable peripherals on one silicon die. The Cortex-M0+ core sits at the low-power end of the ARM Cortex-M family, balancing deterministic performance with minimal energy per instruction. Microcontrollers in this class form the foundation of embedded systems spanning home automation, metering, consumer electronics, and industrial sensors, where deterministic real-time response and low standby current are essential.
Key features of the ATSAMD20G15G15 include an Event System that lets peripherals trigger each other without CPU intervention, reducing latency and current consumption, plus a SleepWalking capability that allows peripherals to operate while the CPU remains in deep sleep. The integrated PTC supports capacitive touch sensing, eliminating external touch controller ICs in many HMI designs. The SERCOM modules can be software-configured as UART, SPI, I2C, or LIN, giving designers maximum flexibility in a 48-pin budget.
The device uses a 32-bit ARM Cortex-M0+ core built on a low-power CMOS process, with a 2.62 mA/MHz active current and multiple low-power modes down to deep sleep with full SRAM retention. The 12-bit ADC provides up to 350 ksps throughput across up to 14 channels, and the 10-bit DAC supports audio and waveform generation. Brown-out detection, watchdog timer, and RTC with calendar mode support battery-backed timekeeping.
Typical applications include home automation devices, smart metering endpoints, consumer HMI with capacitive touch, industrial sensor nodes, low-cost wearables, and battery-powered IoT edge nodes. The wide 1.6V-3.6V supply range supports both single-cell Li-ion and 3.3V regulated rails. AEC-Q100 qualification is not part of this specific suffix; consult the -AUT variant for automotive grade.
When designing with this device, verify that your 48-pin TQFP land pattern matches the published mechanical drawing, and consider migrating to the -AUT suffix for environments requiring -40C to +125C AEC-Q100 qualification. This page consolidates distributor pricing, drop-in pin-compatible alternatives, and practical design guidance not collated in the manufacturer datasheet.
Alternativas drop-in para ATSAMD20G15A-ANT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAMD20G15A-ANT (mesmo formato e footprint) — diferindo em ADC, Operating Temperature, SERCOM Modules, DAC, Package.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAMD20G15A-AUT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATSAMD20G15A-MUT
✅ Drop-In✓ Em estoque
$1.85 / unidade
Ver ficha técnica →ATSAMD20G14A-ANT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATSAMD20G14B-MUT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.1 / unidade
Ver ficha técnica →ATSAMD20E15A-MUT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATSAMD20G15A-ANT Classificações máximas e características elétricas
| Core | ARM Cortex-M0+ 32-bit |
| Maximum CPU Clock | 48 MHz |
| Flash Program Memory | 32 KB |
| SRAM | 4 KB |
| Supply Voltage (VDDIN) | 1.6 V to 3.6 V |
| Temperatura de operação | -40 C to +105 C (industrial) |
| ADC | 12-bit, up to 14 channels |
| DAC | 10-bit, 1 channel |
| Touch Controller (PTC) | 256-channel Peripheral Touch Controller |
| SERCOM Modules | Up to 6 configurable (UART/SPI/I2C/LIN) |
| RTC | Yes, with calendar mode |
| Event System | Yes (peripheral-to-peripheral) |
| Encapsulamento | 48-pin TQFP (7x7 mm) |
| Tipo de montagem | Surface Mount |
| Nível MSL | MSL3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant (Pb-free) |
| AEC-Q100 Qualification | Not qualified (industrial grade) |
Configuração de pinos do ATSAMD20G15A-ANT
| Pino 1 | VDDIO — Digital I/O supply voltage |
| Pino 2 | PA02 — GPIO / ADC AIN[0] |
| Pino 3 | PA03 — GPIO / ADC AIN[1] / DAC VOUT |
| Pino 4 | PA04 — GPIO / VREF |
| Pino 5 | PA05 — GPIO |
| Pino 6 | PA06 — GPIO / PTC Y[6] |
| Pino 7 | PA07 — GPIO / PTC X[7] |
| Pino 8 | VDDIN — Main voltage supply input |
| Pino 9 | GND — Ground |
| Pino 10 | PA08 — GPIO / PTC X[8] |
| Pino 11 | PA09 — GPIO / PTC X[9] / SERCOM |
| Pino 12 | PA10 — GPIO / PTC Y[10] |
| Pino 13 | PA11 — GPIO / PTC X[11] / SERCOM |
| Pino 14 | PA14 — GPIO / PTC X[14] / SERCOM |
| Pino 15 | PA15 — GPIO / PTC X[15] / SERCOM |
| Pino 16 | PA16 — GPIO / PTC Y[16] |
| Pino 17 | PA17 — GPIO / PTC Y[17] |
| Pino 18 | PA18 — GPIO / PTC X[18] |
| Pino 19 | PA19 — GPIO / PTC X[19] / SERCOM |
| Pino 20 | VDDIO — Digital I/O supply voltage |
| Pino 21 | GND — Ground |
| Pino 22 | PA20 — GPIO / PTC Y[20] |
| Pino 23 | PA21 — GPIO / PTC Y[21] / SERCOM |
| Pino 24 | PA22 — GPIO / PTC X[22] / SERCOM |
| Pino 25 | PA23 — GPIO / PTC X[23] |
| Pino 26 | PA24 — GPIO / USB DP (not bonded on this device) |
| Pino 27 | PA25 — GPIO / USB DM (not bonded on this device) |
| Pino 28 | RESETn — Reset input, active low |
| Pino 29 | PA27 — GPIO |
| Pino 30 | PA28 — GPIO |
| Pino 31 | GND — Ground |
| Pino 32 | VDDIO — Digital I/O supply voltage |
| Pino 33 | PB00 — GPIO |
| Pino 34 | PB01 — GPIO |
| Pino 35 | PB02 — GPIO / SERCOM |
| Pino 36 | PB03 — GPIO / SERCOM |
| Pino 34 | PB04 — GPIO |
| Pino 37 | PB05 — GPIO |
| Pino 38 | PB06 — GPIO |
| Pino 39 | PB07 — GPIO |
| Pino 40 | PB08 — GPIO / SERCOM |
| Pino 41 | PB09 — GPIO / SERCOM |
| Pino 42 | PB10 — GPIO / SERCOM |
| Pino 43 | PB11 — GPIO / SERCOM |
| Pino 44 | GND — Ground |
| Pino 45 | VDDIN — Main voltage supply input |
| Pino 46 | PA30 — GPIO / SWD CLK |
| Pino 47 | PA31 — GPIO / SWD IO |
| Pino 48 | GND — Ground |
Aplicações típicas
ATSAMD20G15A-ANT é adequado para 6 aplicaçãos: Home Automation Hubs and Sensor Nodes, Smart Metering and Energy Monitoring, Consumer HMI with Capacitive Touch, Industrial Sensor and Process Monitor, Battery-Powered IoT Edge Devices, Automotive Body and Convenience Electronics.
Home Automation Hubs and Sensor Nodes
The ATSAMD20G15A-ANT suits home automation hubs, Zigbee/BLE endpoints, and wireless sensor nodes because its ARM Cortex-M0+ core at 48 MHz delivers responsive event handling while consuming only 2.62 mA/MHz active. The 32 KB flash accommodates protocol stacks like BLE Mesh or Zigbee cluster libraries with firmware headroom, and the 6 SERCOMs can be software-configured as UART for a host radio, SPI for an external sensor, and I2C for an environmental sensor. The 1.6-3.6 V supply range supports single-cell Li-ion battery operation directly, and SleepWalking allows peripherals to wake the CPU only when a sensor threshold is crossed, yielding months of battery life in typical thermostat or door sensor duty cycles. The integrated 256-channel PTC eliminates the need for an external touch controller in wall switches.
Recomendado
Smart Metering and Energy Monitoring
The ATSAMD20G15A-ANT is well matched to smart electricity, water, and gas metering endpoints. Its 12-bit ADC at up to 350 ksps accurately samples current shunts or voltage dividers for energy calculation with sufficient resolution for Class 1 metering accuracy. The 4 KB SRAM buffers energy accumulation registers between RTC-timed logging events, while the 32 KB flash stores metering firmware with persistent calibration tables. The wide 1.6-3.6 V supply lets the MCU run directly from a single Li-ion or two AA cells, and the RTC with calendar mode enables time-of-use billing schedules. Brown-out detection and watchdog timer support long-term unattended operation in basement or outdoor installations where manual reset is impractical.
Recomendado
Consumer HMI with Capacitive Touch
The ATSAMD20G15A-ANT integrates Microchip's 256-channel Peripheral Touch Controller (PTC) which scans up to 256 capacitive touch electrodes without an external touch controller IC. This drives down BOM cost in white goods, audio controls, induction cooktops, and small appliances where a 7-segment display plus touch keypad is the primary user interface. The PTC supports both self-capacitance and mutual-capacitance sensing topologies, with hardware-accelerated scanning and noise-immune acquisition that operates reliably under noisy SMPS environments. The 48 MHz Cortex-M0+ core runs the user interface logic and debounces touch events, while the 4 KB SRAM holds display buffers. Compared to a discrete touch controller approach, the integrated PTC saves both PCB area and approximately $0.40 per unit on the BOM.
Recomendado
Industrial Sensor and Process Monitor
The ATSAMD20G15A-ANT fits industrial 4-20 mA loop-powered sensor transmitters, RTD/thermocouple conditioning front ends, and predictive maintenance sensor pods. Its -40C to +105 C industrial temperature range covers most factory floor environments, and the 12-bit ADC measures process variables with sufficient accuracy for non-precision control loops. The Event System lets a sensor ADC trigger SERCOM SPI upload without waking the CPU, reducing average power in battery-powered wireless sensor pods. The SERCOMs can be software-configured as RS-485 UART for legacy industrial busses or I2C for digital sensors, and the 6-channel configurability covers most 4-20 mA + HART-modem bridge designs. The wide supply range supports both 24V industrial rails via a regulator and battery-backed operation during line power loss.
Recomendado
Battery-Powered IoT Edge Devices
The ATSAMD20G15A-ANT is ideal for battery-powered IoT edge nodes like environmental monitors, asset trackers, and wearable health bands. The 1.6-3.6 V supply range lets it run directly from a single CR2032 coin cell or Li-Po battery without an external regulator, and SleepWalking peripherals can monitor I2C sensors while the CPU remains in deep sleep. The ARM Cortex-M0+ core's Thumb-2 efficiency yields more MIPS per milliwatt than 8-bit MCUs, which extends coin-cell life by months in duty-cycled applications. The 32 KB flash comfortably fits BLE stack fragments or LoRaWAN MAC layer code, and the integrated 10-bit DAC enables audio cue generation or analog feedback signals without an external DAC IC.
Recomendado
Automotive Body and Convenience Electronics
The ATSAMD20G15A-ANT supports non-safety automotive body electronics like HVAC control panels, seat adjustment switches, lighting dimmers, and door-zone controllers where AEC-Q100 grade is not strictly required. The 32 KB flash holds CAN node firmware with diagnostic UDS support, and the SERCOMs can be software-configured as CAN, SPI, or LIN interfaces for body-domain networks. The 12-bit ADC accurately reads potentiometers for HVAC blend doors and seat position, while the DAC drives analog gauge pointers in some instrument cluster sub-modules. For designs that must be AEC-Q100 qualified, migrate to the ATSAMD20G15A-AUT suffix which shares the same 48-pin TQFP footprint and pinout, enabling a single PCB design that supports both industrial and automotive variants.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAMD20G15A-ANT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAMD20G15A-AUT | ATSAMD20G15A-MUT | ATSAMD20G14A-ANT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-pin TQFP (7x7 mm) | 48-pin TQFP (7x7 mm) - same | 48-pin QFN (7x7 mm) - different footprint | 48-pin TQFP (7x7 mm) - same |
| Core / Architecture | ARM Cortex-M0+ 32-bit | ARM Cortex-M0+ 32-bit | ARM Cortex-M0+ 32-bit | ARM Cortex-M0+ 32-bit |
| Flash | 32 KB | 32 KB | 32 KB | 16 KB (-50%) |
| SRAM | 4 KB | 4 KB | 4 KB | 2 KB (-50%) |
| Operating Temperature | -40C to +105C (industrial) | -40C to +125C (automotive) | -40C to +125C (automotive) | -40C to +105C (industrial) |
| AEC-Q100 Qualification | Not qualified | Yes (automotive grade) | Yes (automotive grade) | Not qualified |
| PTC Touch Channels | 256 | 256 | 256 | 256 |
Principais diferenciais
- Integrated 256-channel Peripheral Touch Controller (vs PIC16F636-I/ST)
- Six SERCOM-configurable serial interfaces (vs STM32F072C8T6)
- Cortex-M0+ at 48 MHz versus PIC16F at 20 MHz (vs PIC16F636-I/ST)
Notas de projeto
Place a 1uF X7R ceramic bypass capacitor within 2 mm of each VDDIN and VDDIO pin pair, with a 0.1uF ceramic placed immediately at the pin. The internal 1.2 V core regulator requires minimum 1uF bulk capacitance on VDDOUT. According to Microchip SAM D20 family design notes, starved VDDIO bypass causes brown-out events during peak ADC sampling, so do not omit the bulk capacitor.
Keep the 48-pin TQFP land pattern within 0.5 mm pitch with solder mask defined (SMD) pads. Route the RESETn line directly to a debugger header with no series resistance above 100 ohm to preserve SWD signal integrity. Keep the VDDIN traces at least 0.5 mm wide and decouple them within 5 mm of the pin to avoid ringing during peak load steps from the ADC or SERCOM switching.
Estimated: At VDDIN = 3.3 V and full 48 MHz active current of 2.62 mA/MHz, the device draws approximately 126 mA peak. Designers migrating from PIC16F or STM32F0 designs frequently omit the SERCOM MUX configuration in code, leaving all serial interfaces disabled at reset. Verify SERCOM pad configuration via the PORT and PMUX registers in startup code before enabling peripherals, or the firmware will hang at the first UART/SPI/I2C access.
When using the 12-bit ADC at sample rates above 100 ksps, add a 10 nF ceramic bypass capacitor on each AIN pin within 5 mm to limit switching charge injection noise. Per the SAM D20 datasheet ADC section, ADC accuracy degrades by 1-2 LSB if the source impedance exceeds 1 kohm. For high-impedance sensors use an external op-amp buffer rather than relying on the ADC input leakage current specification of 1 uA maximum.
Informações de conformidade
RoHS compliant per Microchip product page (Pb-free 48-pin TQFP). AEC-Q100 not applicable for industrial -ANT suffix; migrate to ATSAMD20G15A-AUT for automotive grade.
