ATSAMD21E18A-AU - 48MHz Cortex-M0+ MCU | Microchip
N.º da peça: ATSAMD21E18A-AU ✓ AtivoATSAMD21E18A-AU Visão geral
A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, working memory, input/output ports, and peripherals onto one package. The Cortex-M0+ processor belongs to the ARM Cortex-M family of low-power, deterministic embedded processors. Within the device hierarchy, the ATSAMD21E18A-AU is a SAM D21E-family MCU and a Flash-based embedded controller designed to operate from a 1.6 V to 3.6 V supply.
The principal device ratings include a maximum CPU frequency of 48 MHz, 256 KB of Flash storage, 32 KB of SRAM, and a 1.6 V to 3.6 V operating-voltage range. The part is identified as a Functional Safety microcontroller in the DigiKey product listing. Its integrated interface resources include I2C, SPI, UART/USART, USB, DMA, and I2S capabilities, while its approximately 26 general-purpose I/O lines provide flexible connections to sensors, actuators, displays, and external communications devices.
The SAM D21 architecture combines a 32-bit Cortex-M0+ core with event-oriented peripherals and direct-memory-access support. This structure allows peripheral transfers to occur without requiring each byte to be processed by the CPU. The 48 MHz operating limit provides additional scheduling and signal-processing headroom compared with slower general-purpose MCUs, while the 256 KB Flash area supports substantially larger embedded applications than devices limited to 64 KB of program memory.
Typical applications include connected home automation, industrial sensing and metering, consumer controls, compact sensor nodes, and USB-connected embedded accessories. The I2C and SPI interfaces suit sensors and memory devices, UART/USART supports serial modules, and USB enables configuration, logging, or firmware update connectivity when the board design implements the required USB circuitry.
Design the PCB with short, continuous supply and ground paths, place decoupling capacitors close to the supply pins, and route sensitive analog and communications signals away from fast-switching nodes. Confirm the package pin assignments and alternate-function requirements in the manufacturer datasheet before assigning external functions or programming the device.
This product record combines the manufacturer’s device characteristics with package, sourcing, and replacement guidance. It also identifies engineering trade-offs for the ATSAMD21E18A-AU and explains which same-package alternatives can be evaluated when supply, qualification, or device functionality differs.
Alternativas drop-in para ATSAMD21E18A-AU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAMD21E18A-AU (mesmo formato e footprint) — diferindo em Package, RoHS Status, ADC, SRAM, Flash Memory.
ATSAMD20E18A-AU
✅ Drop-InConsulte o preço
Ver ficha técnica →ATSAMD21E18A-AU Classificações máximas e características elétricas
| Product Type | 32-bit ARM Cortex-M0+ Flash microcontroller |
| CPU Core | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 256 KB |
| SRAM | 32 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| Encapsulamento | 32-pin TQFP, 7 x 7 mm |
| General-Purpose I/O | Approximately 26 |
| Serial Interfaces | I2C, SPI, UART/USART, USB, and I2S |
| DMA Support | Yes |
| Functional Safety | FuSa microcontroller |
| Program Memory Type | Flash |
| Architecture | Harvard |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do ATSAMD21E18A-AU 32-pin tqfp, 7 x 7 mm
Configuração de pinos para ATSAMD21E18A-AU (pacote 32-pin tqfp, 7 x 7 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATSAMD21E18A-AU.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATSAMD21E18A-AU é adequado para 6 aplicaçãos: Home Automation Controller, Industrial Sensor Node, USB-Connected Embedded Accessory, Smart Energy Metering, Consumer Appliance Control, Data Logger and Remote Sensor Interface.
Home Automation Controller
The ATSAMD21E18A-AU fits a compact home-automation controller because its 48 MHz Cortex-M0+ core provides useful scheduling headroom while the 256 KB Flash and 32 KB SRAM support protocol handlers, state machines, and local configuration data. I2C and SPI can connect environmental sensors, display controllers, and memory devices, while UART/USART supports radio or gateway modules. The 32-pin TQFP package limits the available I/O to approximately 26 general-purpose lines, so the design should map each switch, relay, and sensor connection before finalizing the PCB.
Recomendado
Industrial Sensor Node
The ATSAMD21E18A-AU is appropriate for a low-power industrial sensor node that combines several sensing and communications functions. Its 48 MHz processing rate supports protocol processing and local filtering, while the 1.6 V to 3.6 V operating range permits integration with 3.3 V sensor systems. I2C and SPI can serve digital sensors, while UART/USART can provide a robust link to a local controller. Design the supply section for the selected radio or actuator load, provide local decoupling, and validate the environmental requirements independently of the MCU’s functional-safety designation.
Recomendado
USB-Connected Embedded Accessory
The ATSAMD21E18A-AU can serve as the controller in a USB-connected accessory that needs more program storage than a small 8-bit MCU. Its 256 KB Flash accommodates firmware, USB descriptors, configuration handling, and application logic, while 32 KB of SRAM supports transient protocol buffers. The integrated USB capability can support configuration, diagnostics, or firmware update paths, subject to the required external USB circuit implementation. Confirm device programming, boot behavior, bus-routing details, and signal integrity against the manufacturer reference design before production.
Recomendado
Smart Energy Metering
The ATSAMD21E18A-AU is suitable for metering equipment that must combine acquisition control, calibration routines, and a communications interface. Its 48 MHz Cortex-M0+ core can handle multiple scheduled tasks, while 256 KB of Flash and 32 KB of SRAM provide room for protocol stacks and working buffers. I2C and SPI suit external converters or memory, and UART/USART can connect a communications module. Because metering designs may require precise analog front ends and regulatory verification, keep the MCU interface layout deterministic and obtain the required metering-specific component requirements.
Recomendado
Consumer Appliance Control
The ATSAMD21E18A-AU can control a compact consumer appliance that combines buttons, indicators, sensors, and an external communications module. The 48 MHz core allows responsive control logic, and the 256 KB Flash supports a larger application and update mechanism than memory-constrained 8-bit devices. I2C and SPI provide flexible peripheral expansion, while UART/USART can interface with a display or radio module. The TQFP footprint is easy to inspect during production, but its approximately 26 I/O lines require careful budgeting for indicators, actuators, debug access, and future expansion.
Recomendado
Data Logger and Remote Sensor Interface
The ATSAMD21E18A-AU fits a local data logger that receives information from sensors and forwards it through a serial or USB link. Its 32 KB of SRAM supports transient acquisition and protocol buffers, while the 48 MHz CPU supports efficient event handling and formatting. I2C and SPI are suitable for short-distance sensor connections, and DMA can reduce CPU involvement during peripheral transfers. Place serial interfaces away from switching nodes, keep the clock and power paths clean, and confirm the maximum peripheral clock and electrical limits in the manufacturer datasheet before selecting external memory.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAMD21E18A-AU — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAMD20E18A-AU |
|---|---|---|
| Package | 32-pin TQFP, 7 x 7 mm | 32-pin TQFP |
| Brand | Microchip Technology | Microchip Technology |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz |
| Flash Memory | 256 KB | 256 KB |
| Operating Voltage Range | 1.6 V to 3.6 V | 1.8 V, 2.5 V, or 3.3 V |
| Device Family | SAM D21E | SAM D20E |
Principais diferenciais
- Newer SAM D21E device family with Functional Safety identification (vs ATSAMD20E18A-AU)
- Matches a 48 MHz, 256 KB Flash performance profile (vs ATSAMD20E18A-AU)
- Uses a 32-pin 7 x 7 mm TQFP footprint (vs ATSAMD20E18A-AU)
Notas de projeto
Place the device-side supply capacitors immediately adjacent to the relevant VDD and ground pins, using the manufacturer’s recommended capacitance and ESR range. Keep the 1.6 V to 3.6 V operating limit in mind when selecting the regulator and defining fault behavior outside the valid range. Route the ground reference as a continuous plane or carefully stitched return path so return current from serial, USB, and switching-adjacent circuitry does not share long traces with the MCU.
Assign every TQFP pin from the manufacturer pin-description table before placing the schematic symbols or routing PCB traces. Several SAM D21E functions can be multiplexed onto the same I/O, and the required function may depend on peripheral settings or an alternate-function mux. Check package-pin numbering, power pins, ground pins, debug access, reset behavior, and boot-related connections rather than inferring the footprint from a generic 32-pin symbol.
Keep I2C, SPI, USB, and other communication routes short and isolated from clocks and high-current switching nodes. Follow the manufacturer’s recommended external resistor and capacitor arrangements for each interface, especially USB and reset. If an external crystal or resonator is used, place its load components and connection path close to the oscillator pins with a controlled ground return; otherwise, use the internal clock arrangement specified by the manufacturer.
Do not treat a related SAM D20 or SAM D21 ordering code as automatically interchangeable. Package size alone does not guarantee identical pin multiplexing, peripheral availability, interrupt behavior, bootloader operation, or register compatibility. The ATSAMD20E18A-AU is a useful same-package engineering-review candidate, but a production substitution requires comparison of every used pin, power requirement, clock source, peripheral instance, and firmware dependency against the original design.
Informações de conformidade
The Functional Safety designation in the DigiKey listing does not establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Compliance documentation should be requested for the exact ordering code.