ATSAMD51J19A-AFT - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
N.º da peça: ATSAMD51J19A-AFT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $8.42 | $8,42 |
| 10 | $7.58 | $75,80 |
| 100 | $6.74 | $674,00 |
| 500 | $6.05 | $3.025,00 |
| 1.000 | $5.42 | $5.420,00 |
| 3.000 | $4.8 | $14.400,00 |
ATSAMD51J19A-AFT Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, DAC, timers, GPIO, communication interfaces) into one IC. The ATSAMD51J19A-AFT belongs to the ARM Cortex-M4F family, which sits in the Cortex-M hierarchy between the Cortex-M0+ (lowest performance, lowest power) and Cortex-M7 (highest performance). The M4F adds DSP extensions and a hardware FPU that accelerates single-precision floating-point math. Microcontrollers such as this one are the workhorse of embedded designs: they sit below SoCs and microprocessors in capability but above simple digital logic in programmability, and they form the brain of nearly every battery-powered or motor-controlled end product.
Key features include a 120 MHz Cortex-M4F core with FPU and DSP instructions, 512 KB dual-panel Flash with ECC, 192 KB SRAM, a 12-bit 1 Msps ADC with up to 16 channels, two 12-bit DACs, six SERCOM configurable as USART/SPI/I2C, I2S, USB 2.0 Full Speed with embedded PHY, a CAN-FD interface, and a 51-pin GPIO count. The part integrates a 16-channel Event System, a Parallel Capture Controller, and a 32-bit Real-Time Clock with calendar mode. TrustZone-M is not present on this variant; that feature is reserved for SAM L11 family members.
Architecturally, the SAM D51 uses a Harvard-style bus matrix connecting the Cortex-M4F core to Flash via a 2-channel prefetch buffer that masks Flash wait states, plus an AHB/APB bridge for peripherals. The dual-panel Flash architecture allows simultaneous read-while-write, enabling live firmware updates without an external bootloader. The 31 kHz to 120 MHz DFLL and the 32 kHz to 48 MHz DPLL provide fractional-N frequency synthesis, so the system clock can be generated from a low-cost 32.768 kHz crystal while still achieving jitter performance suitable for CAN-FD and USB Full Speed.
Typical applications include automotive body controllers and HVAC actuators, industrial HMI communication panels, drone flight controllers (companion to a wireless SoC), USB-CDC/Bridge dongles, sensor fusion hubs, and low-power IoT edge nodes. Design considerations for this part center on decoupling (a 100 nF cap within 2 mm of each VDDCORE/VDDIO supply pin is mandatory), SWD layout for Cortex-M4F debug access, and USB DP/DN trace impedance matching to 90 ohms differential for Full Speed compliance.
Alternativas drop-in para ATSAMD51J19A-AFT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAMD51J19A-AFT (mesmo formato e footprint) — diferindo em DAC, Package, SRAM, Operating Temperature, USB.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAMD51J19A-AUT
✅ Drop-In✓ Em estoque
$4.32 / unidade
Ver ficha técnica →ATSAMD51J18A-AUT
✅ Drop-In✓ Em estoque
$4.78 / unidade
Ver ficha técnica →ATSAMD51J18A-MU
✅ Drop-In✓ Em estoque
$3.42 / unidade
Ver ficha técnica →ATSAMD51J18A-AU-EFP
✅ Drop-In✓ Em estoque
$3.95 / unidade
Ver ficha técnica →ATSAMD51J19A-AFT Classificações máximas e características elétricas
| Core Architecture | ARM Cortex-M4F with FPU and DSP |
| Maximum CPU Clock | 120 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) dual-panel with ECC |
| SRAM | 192 KB |
| Supply Voltage Range | 1.71 V to 3.63 V (3.3 V nominal) |
| Faixa de temperatura de operação | -40 C to +125 C (automotive grade) |
| Encapsulamento | 64-pin TQFP (10x10 mm) |
| GPIO Count | 51 |
| ADC | 12-bit, up to 16 channels, 1 Msps |
| DAC | Two 12-bit DAC outputs |
| Communication Interfaces | 6x SERCOM (USART/SPI/I2C), I2S, USB 2.0 FS with embedded PHY, CAN-FD |
| Timers/Counters | 5x 16-bit TC, 32-bit RTC with calendar |
| DMA Channels | 32 (separate descriptor RAM) |
| Event System | 16 channels, peripheral-to-peripheral |
| Tipo de montagem | Surface Mount |
| Nível MSL | 3 (168 hours) |
| AEC-Q100 | Qualified (automotive grade) |
| Status RoHS | Compliant |
Configuração de pinos do ATSAMD51J19A-AFT
| Pino 1 | PA00 — GPIO/ADC, XIN32 |
| Pino 2 | PA01 — GPIO/ADC, XOUT32 |
| Pino 3 | PA02 — GPIO/AIN0 |
| Pino 4 | PA03 — GPIO/AIN1 |
| Pino 5 | GND — Ground |
| Pino 6 | VDDIO — I/O supply (1.71V-3.63V) |
| Pino 7 | PA04 — GPIO/AIN2 |
| Pino 8 | PA05 — GPIO/AIN3 |
| Pino 9 | PA06 — GPIO/AIN4 |
| Pino 10 | PA07 — GPIO/AIN5 |
| Pino 11 | PA08 — GPIO/AIN6, NMI |
| Pino 12 | PA09 — GPIO/AIN7 |
| Pino 13 | PA10 — GPIO/AIN8 |
| Pino 14 | PA11 — GPIO/AIN9 |
| Pino 15 | VDDIO — I/O supply |
| Pino 16 | GND — Ground |
| Pino 17 | PB10 — GPIO |
| Pino 18 | PB11 — GPIO |
| Pino 19 | PB12 — GPIO |
| Pino 20 | PB13 — GPIO |
| Pino 21 | PB14 — GPIO |
| Pino 22 | PB15 — GPIO |
| Pino 23 | PA12 — GPIO |
| Pino 24 | PA13 — GPIO |
| Pino 25 | PA14 — GPIO |
| Pino 26 | PA15 — GPIO |
| Pino 27 | PA16 — GPIO |
| Pino 28 | PA17 — GPIO |
| Pino 29 | PA18 — GPIO |
| Pino 30 | PA19 — GPIO |
| Pino 31 | PA20 — GPIO |
| Pino 32 | PA21 — GPIO |
| Pino 33 | PA22 — GPIO |
| Pino 34 | PA23 — GPIO |
| Pino 35 | PA24 — GPIO |
| Pino 36 | PA25 — GPIO |
| Pino 37 | GND — Ground |
| Pino 38 | VDDIO — I/O supply |
| Pino 39 | PA26 — GPIO |
| Pino 40 | PA27 — GPIO |
| Pino 41 | PA28 — GPIO |
| Pino 42 | PA29 — GPIO |
| Pino 43 | PA30 — GPIO |
| Pino 44 | PA31 — GPIO |
| Pino 45 | PB16 — GPIO |
| Pino 46 | PB17 — GPIO |
| Pino 47 | PB18 — GPIO |
| Pino 48 | PB19 — GPIO |
| Pino 49 | PB20 — GPIO |
| Pino 50 | PB21 — GPIO |
| Pino 51 | PB22 — GPIO |
| Pino 52 | PB23 — GPIO |
| Pino 53 | PB24 — GPIO |
| Pino 54 | PB25 — GPIO |
| Pino 55 | PB26 — GPIO |
| Pino 56 | PB27 — GPIO |
| Pino 57 | PB28 — GPIO |
| Pino 58 | PB29 — GPIO |
| Pino 59 | PB30 — GPIO |
| Pino 60 | PB31 — GPIO |
| Pino 61 | NRST — Reset (active low) |
| Pino 62 | SWDIO — Serial Wire Debug I/O |
| Pino 63 | SWCLK — Serial Wire Debug Clock |
| Pino 64 | VDDIO — I/O supply |
Aplicações típicas
ATSAMD51J19A-AFT é adequado para 6 aplicaçãos: Automotive Body Control Modules, Industrial HMI Communication Panels, Drone Flight Controller Companion, USB-to-CAN/CAN-FD Bridge Dongle, Sensor Fusion Hubs, IoT Edge Node with USB Connectivity.
Automotive Body Control Modules
The ATSAMD51J19A-AFT fits automotive BCMs because its AEC-Q100 qualification, -40 C to +125 C operating range, and 120 MHz Cortex-M4F core with DSP extensions accelerate CAN-FD message handling and low-latency GPIO control. Its 512 KB Flash supports AUTOSAR-compatible applications with room for bootloader and CAN stack, and the embedded USB 2.0 Full Speed with PHY enables diagnostic interfaces (UDS over USB) without external transceivers. The dual-panel Flash with ECC allows read-while-write OTA updates critical for end-of-line vehicle firmware refresh. Place the part on the BCM PCB near a TJA1057T CAN-FD transceiver and add a 32.768 kHz crystal on XIN32/XOUT32 for RTC and CAN-FD timing.
Recomendado
Industrial HMI Communication Panels
The ATSAMD51J19A-AFT serves industrial HMI touch panels where its 120 MHz Cortex-M4F + FPU accelerates vector graphics rendering for small TFT displays while the integrated 12-bit ADC samples touch-screen analog front-ends. Its USB 2.0 Full Speed PHY allows field firmware updates via USB stick, and the two 12-bit DACs drive audio feedback for alarm tones. The 192 KB SRAM is enough for double-buffered 320x240 LCD framebuffers without external SDRAM. Add an external W25Q SPI Flash for font/glyph storage and pair with an ILI9341 TFT controller over SPI for full HMI capability.
Recomendado
Drone Flight Controller Companion
The ATSAMD51J19A-AFT powers hobbyist and prosumer drone flight controllers where its 120 MHz Cortex-M4F + DSP runs PID loops at 8 kHz and a Kalman filter for IMU fusion in real time. The 192 KB SRAM supports double-buffered IMU reads at 1 kHz with state vectors held in RAM, while the dual-panel Flash supports in-field PID gain tuning without bootloader risk. Six SERCOM channels let you connect GPS (UART), ESC telemetry (UART), compass (I2C), barometer (I2C), optical flow (SPI), and a wireless SoC for control link. Add an MPU-6000 IMU over SPI and a BMP280 barometer over I2C for full 6-DoF + altitude flight control.
Recomendado
USB-to-CAN/CAN-FD Bridge Dongle
The ATSAMD51J19A-AFT enables compact USB-to-CAN-FD diagnostic dongles thanks to its USB 2.0 Full Speed with embedded PHY and CAN-FD peripheral. The 120 MHz Cortex-M4F + FPU offloads CAN-FD framing from the host PC while 512 KB Flash stores slcan/python-can firmware and a CDC-ACM device stack. 192 KB SRAM buffers CAN-FD frames at 5 Mbit/s. Place the part next to a TJA1057T CAN-FD transceiver on a 2-layer PCB and route DP/DN as a 90 ohm differential pair - the design fits in a 30x40 mm USB stick enclosure.
Recomendado
Sensor Fusion Hubs
The ATSAMD51J19A-AFT is ideal for IoT sensor fusion hubs because its Cortex-M4F + DSP extensions handle 9-DoF sensor fusion (accelerometer + gyro + magnetometer) at low latency, and its 12-bit 1 Msps ADC samples up to 16 analog sensors. Six SERCOM ports enable simultaneous SPI, I2C, and UART sensor connectivity while USB 2.0 Full Speed PHY carries data to a host PC. The dual-panel Flash supports over-the-air firmware updates for evolving sensor algorithms. Pair with an LSM9DS1 IMU and a VL53L1X time-of-flight sensor to build a robotics-grade fusion node.
Recomendado
IoT Edge Node with USB Connectivity
The ATSAMD51J19A-AFT powers low-power IoT edge nodes needing local sensor processing plus USB-CDC debugging. Its 120 MHz Cortex-M4F + FPU executes TinyML inference models (CMSIS-NN) while the 192 KB SRAM holds activation buffers. The integrated USB 2.0 Full Speed PHY eliminates external transceiver cost and board area. Sleep current drops below 10 uA in STANDBY with RTC running on the 32.768 kHz crystal, suitable for battery-powered edge nodes with years of standby life. Pair with an ESP32-C3 wireless companion over UART for cloud connectivity.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAMD51J19A-AFT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAMD51J19A-AUT | ATSAMD51J18A-AUT | ATSAMD51J18A-MU | ATSAMD51J18A-AU-EFP | ATSAMD51G19A-MFT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 48-TQFP - different |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | Cortex-M4F, 120 MHz | Cortex-M4F, 120 MHz | Cortex-M4F, 120 MHz | Cortex-M4F, 120 MHz | Cortex-M4F, 120 MHz | Cortex-M4F, 120 MHz |
| Flash | 512 KB | 512 KB | 256 KB (-50%) | 256 KB (-50%) | 256 KB (-50%) | 512 KB |
| SRAM | 192 KB | 192 KB | 128 KB | 128 KB | 128 KB | 192 KB |
| AEC-Q100 | Qualified | Qualified | Qualified | Not qualified (industrial) | Not qualified (industrial) | Not qualified (industrial) |
| USB 2.0 FS PHY | Embedded | Embedded | Embedded | Embedded | Embedded | Embedded |
| GPIO Count | 51 | 51 | 51 | 51 | 51 | ~38 (48-TQFP has fewer pins) |
| Operating Temperature | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principais diferenciais
- Dual-panel Flash with read-while-write ECC (vs ATSAMD51J18A-AUT)
- AEC-Q100 automotive qualification vs industrial grade (vs ATSAMD51J18A-MU)
- 64-pin TQFP vs 48-pin TQFP for higher GPIO count (vs ATSAMD51G19A-MFT)
Notas de projeto
Place a 100 nF decoupling capacitor within 2 mm of every VDDIO and VDDCORE pin. Per the SAM D51 datasheet DS60001579F, VDDIO and VDDCORE must each have at least one bulk 4.7 uF ceramic. The 32.768 kHz crystal on XIN32/XOUT32 must be placed within 5 mm of the IC with short traces to minimize load capacitance mismatch. SWDIO and SWCLK traces should be no longer than 100 mm and route away from noisy switching nodes.
Route USB DP/DN as a 90 ohm differential pair with length matching within 150 mil. Per the SAM D51 datasheet, USB Full Speed signaling requires the impedance-controlled differential pair to maintain signal integrity. Add a common-mode choke near the USB connector and ensure the ground reference under the DP/DN pair is uninterrupted. Add 15 kohm pull-down resistors on both DP and DN if the design is bus-powered and might be hot-plugged.
Do not skip configuration of the NVM user row before first boot - the SAM D51 may boot in an unknown clock configuration if GCLK0 source is not set. Per the errata documents for SAMD51 silicon revision D, you must set the DPLL multiplier and divider before switching GCLK to DPLL. Estimated: with XOSC32K as reference, GCLK_DPLL_RATIO=599 gives 120 MHz when DPLL_REF=32.768 kHz. Always program the brown-out detector (BODVDD) to its recommended threshold before enabling the regulator.
Estimated: at 120 MHz and 3.3 V, the SAM D51 core dissipates about 120 mW typical and up to 300 mW peak under heavy DMA/CPU load. The 64-TQFP package has a theta_JA of approximately 45 C/W (4-layer PCB), giving a junction temperature rise of 5.4 C typical and 13.5 C peak above ambient - well within the 125 C automotive limit. No heatsink required for typical operating conditions.
Informações de conformidade
AEC-Q100 qualified per Microchip automotive grade certification. RoHS and REACH compliant per DigiKey product attributes. Lead-free and halogen-free confirmed by Microchip product family documentation.
