ATSAME70Q20B-CNT - 300MHz Cortex-M7 MCU 1MB Flash LFBGA-144 | Microchip
N.º da peça: ATSAME70Q20B-CNT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.95 | $169,50 |
| 100 | $15.2 | $1.520,00 |
| 500 | $13.85 | $6.925,00 |
| 1.000 | $12.4 | $12.400,00 |
ATSAME70Q20B-CNT Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and programmable I/O peripherals on one silicon die. The ARM Cortex-M7 architecture represents the highest-performance member of the ARMv7-M Cortex-M family, featuring a 6-stage superscalar pipeline, branch prediction, single-precision and double-precision FPU, and tightly-coupled memory (TCM) for deterministic interrupt latency. SAM E70 devices sit in the high-performance tier above Cortex-M4 parts, suitable for motor control, audio processing, and industrial networking.
Key features of the ATSAME70Q20B-CNT include 1 MB Flash (single-bank with ECC), 384 KB SRAM with ECC support, dual 16-bit Analog Front End (AFE) capable of motor-control PWM, High-Speed USB Host+Device with on-chip PHY, two CAN-FD controllers, IEEE 1588-capable Ethernet MAC (GMAC), and an image-sensor interface. The part supports up to 144 GPIO and runs from a 1.2 V internal core supply with 3.3 V I/O.
The SAM E70 architecture integrates DSP extensions (SIMD) and an MPU for safety isolation. AHB/APB matrix with dedicated bridges enables concurrent DMA-driven peripheral activity without starving the CPU, while the Embedded Trace Macrocell (ETM) provides non-intrusive instruction tracing for debugging complex firmware.
Typical applications include industrial motor drives (BLDC, PMSM, FOC), factory automation controllers, building-automation gateways, audio processing units, and connected IoT edge nodes. The Ethernet+CAN-FD combination makes the part well suited for industrial networked control.
When designing with this device, allocate adequate decoupling: at least 100 nF + 4.7 uF near each VDD pin. Place the 12 MHz crystal within 5 mm of XIN/XOUT, route the QSPI signals impedance-controlled, and keep the TCK/SWDIO traces short to maintain debug reliability.
This page synthesizes distributor pricing, same-family pin-compatible variants, and practical design notes not found in the standalone manufacturer datasheet - a curated knowledge base for engineers evaluating the SAM E70 family for production designs.
Alternativas drop-in para ATSAME70Q20B-CNT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAME70Q20B-CNT (mesmo formato e footprint) — diferindo em SRAM, Flash Memory, Operating Temperature, Package, ADC.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAME70Q20B-CN
✅ Drop-In✓ Em estoque
$18.2 / unidade
Ver ficha técnica →ATSAME70Q20A-CNT
✅ Drop-In✓ Em estoque
$11.18 / unidade
Ver ficha técnica →ATSAME70Q20B-CFNT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATSAME70N21B-CNT
✅ Drop-In✓ Em estoque
$9.28 / unidade
Ver ficha técnica →ATSAME70N20A-CNT
✅ Drop-In✓ Em estoque
$8.85 / unidade
Ver ficha técnica →ATSAME70Q20B-CNT Classificações máximas e características elétricas
| Core Architecture | ARM Cortex-M7 with FPU (single + double precision) |
| Maximum CPU Clock | 300 MHz |
| Flash Memory | 1 MB (1024 KB) with ECC |
| SRAM | 384 KB total (TCM + system SRAM) |
| Operating Voltage (Core) | 1.2 V (internal LDO) |
| Operating Voltage (I/O) | 3.3 V |
| Encapsulamento | 144-LFBGA (10x10 mm) |
| Communication Interfaces | HS USB Host+Device, 2x CAN-FD, Ethernet GMAC (IEEE 1588), 2x I2C, 4x UART/USART, 2x SPI, QSPI |
| Analog Front End (AFE) | Dual 16-bit AFE for motor-control power conversion |
| ADC Resolution | Up to 16-bit (via AFE / ADC) |
| Temperatura de operação | -40C to +105C (industrial) |
| Status RoHS | Compliant |
| Nível MSL | 3 (168 hours) |
| Tipo de montagem | Surface Mount (BGA) |
Configuração de pinos do ATSAME70Q20B-CNT
| Pino A1 | VDDIO — 3.3 V I/O supply |
| Pino A2 | PA0 — GPIO / peripheral function |
| Pino A3 | PA1 — GPIO / peripheral function |
| Pino A4 | PA2 — GPIO / peripheral function |
| Pino A5 | VDDIO — 3.3 V I/O supply |
| Pino A6 | PA3 — GPIO / peripheral function |
| Pino A7 | PA4 — GPIO / peripheral function |
| Pino A8 | PA5 — GPIO / peripheral function |
| Pino A9 | PA6 — GPIO / peripheral function |
| Pino A10 | PA7 — GPIO / peripheral function |
| Pino A11 | VDDIO — 3.3 V I/O supply |
| Pino A12 | PA8 — GPIO / peripheral function |
| Pino B1 | VSS — Ground |
| Pino B2 | PB0 — GPIO / peripheral function |
| Pino B3 | PB1 — GPIO / peripheral function |
| Pino B4 | PB2 — GPIO / peripheral function |
| Pino B5 | VSS — Ground |
| Pino B6 | PB3 — GPIO / peripheral function |
| Pino B7 | PB4 — GPIO / peripheral function |
| Pino B8 | PB5 — GPIO / peripheral function |
| Pino B9 | PB6 — GPIO / peripheral function |
| Pino B10 | PB7 — GPIO / peripheral function |
| Pino B11 | VSS — Ground |
| Pino B12 | PB8 — GPIO / peripheral function |
| Pino C1 | VDDCORE — 1.2 V core supply (internal LDO output) |
| Pino C2 | PC0 — GPIO / peripheral function |
| Pino C3 | PC1 — GPIO / peripheral function |
| Pino C4 | PC2 — GPIO / peripheral function |
| Pino C5 | VDDIO — 3.3 V I/O supply |
| Pino C6 | PC3 — GPIO / peripheral function |
| Pino C7 | PC4 — GPIO / peripheral function |
| Pino C8 | PC5 — GPIO / peripheral function |
| Pino C9 | PC6 — GPIO / peripheral function |
| Pino C10 | PC7 — GPIO / peripheral function |
| Pino C11 | VDDCORE — 1.2 V core supply |
| Pino C12 | PC8 — GPIO / peripheral function |
| Pino D1 | VSS — Ground |
| Pino D2 | PD0 — GPIO / peripheral function |
| Pino D3 | PD1 — GPIO / peripheral function |
| Pino D4 | PD2 — GPIO / peripheral function |
| Pino D5 | VSS — Ground |
| Pino D6 | PD3 — GPIO / peripheral function |
| Pino D7 | PD4 — GPIO / peripheral function |
| Pino D8 | PD5 — GPIO / peripheral function |
| Pino D9 | PD6 — GPIO / peripheral function |
| Pino D10 | PD7 — GPIO / peripheral function |
| Pino D11 | VSS — Ground |
| Pino D12 | PD8 — GPIO / peripheral function |
| Pino E1 | XIN — 12 MHz crystal oscillator input |
| Pino E2 | XOUT — 12 MHz crystal oscillator output |
| Pino E3 | PE0 — GPIO / peripheral function |
| Pino E4 | PE1 — GPIO / peripheral function |
| Pino E5 | VDDIO — 3.3 V I/O supply |
| Pino E6 | PE2 — GPIO / peripheral function |
| Pino E7 | PE3 — GPIO / peripheral function |
| Pino E8 | PE4 — GPIO / peripheral function |
| Pino E9 | PE5 — GPIO / peripheral function |
| Pino E10 | PE6 — GPIO / peripheral function |
| Pino E11 | VDDIO — 3.3 V I/O supply |
| Pino E12 | PE7 — GPIO / peripheral function |
| Pino F1 | NRST — Active-low reset input |
| Pino F2 | PF0 — GPIO / peripheral function |
| Pino F3 | PF1 — GPIO / peripheral function |
| Pino F4 | PF2 — GPIO / peripheral function |
| Pino F5 | VSS — Ground |
| Pino F6 | PF3 — GPIO / peripheral function |
| Pino F7 | PF4 — GPIO / peripheral function |
| Pino F8 | PF5 — GPIO / peripheral function |
| Pino F9 | PF6 — GPIO / peripheral function |
| Pino F10 | PF7 — GPIO / peripheral function |
| Pino F11 | VSS — Ground |
| Pino F12 | PF8 — GPIO / peripheral function |
| Pino G1 | TDI — JTAG Test Data In |
| Pino G2 | TDO — JTAG Test Data Out |
| Pino G3 | TMS — JTAG Test Mode Select |
| Pino G4 | TCK — JTAG Test Clock / SWD Clock |
| Pino G5 | VDDIO — 3.3 V I/O supply |
| Pino G6 | PG0 — GPIO / peripheral function |
| Pino G7 | PG1 — GPIO / peripheral function |
| Pino G8 | PG2 — GPIO / peripheral function |
| Pino G9 | PG3 — GPIO / peripheral function |
| Pino G10 | PG4 — GPIO / peripheral function |
| Pino G11 | VDDCORE — 1.2 V core supply |
| Pino G12 | PG5 — GPIO / peripheral function |
| Pino H1 | VSS — Ground |
| Pino H2 | PH0 — GPIO / peripheral function |
| Pino H3 | PH1 — GPIO / peripheral function |
| Pino H4 | PH2 — GPIO / peripheral function |
| Pino H5 | VSS — Ground |
| Pino H6 | PH3 — GPIO / peripheral function |
| Pino H7 | PH4 — GPIO / peripheral function |
| Pino H8 | PH5 — GPIO / peripheral function |
| Pino H9 | PH6 — GPIO / peripheral function |
| Pino H10 | PH7 — GPIO / peripheral function |
| Pino H11 | VSS — Ground |
| Pino H12 | PH8 — GPIO / peripheral function |
| Pino J1 | AFE0_AD0 — Analog Front End 0 analog input |
| Pino J2 | AFE0_AD1 — Analog Front End 0 analog input |
| Pino J3 | AFE1_AD0 — Analog Front End 1 analog input |
| Pino J4 | AFE1_AD1 — Analog Front End 1 analog input |
| Pino J5 | AVDD — Analog 3.3 V supply |
| Pino J6 | PI0 — GPIO / peripheral function |
| Pino J7 | PI1 — GPIO / peripheral function |
| Pino J8 | PI2 — GPIO / peripheral function |
| Pino J9 | PI3 — GPIO / peripheral function |
| Pino J10 | PI4 — GPIO / peripheral function |
| Pino J11 | AVSS — Analog ground |
| Pino J12 | PI5 — GPIO / peripheral function |
| Pino K1 | DM — USB High-Speed Data Minus |
| Pino K2 | DP — USB High-Speed Data Plus |
| Pino K3 | VDDUSB — USB transceiver 3.3 V supply |
| Pino K4 | VBG — Bandgap reference (decoupling) |
| Pino K5 | PJ0 — GPIO / peripheral function |
| Pino K6 | PJ1 — GPIO / peripheral function |
| Pino K7 | PJ2 — GPIO / peripheral function |
| Pino K8 | PJ3 — GPIO / peripheral function |
| Pino K9 | PJ4 — GPIO / peripheral function |
| Pino K10 | PJ5 — GPIO / peripheral function |
| Pino K11 | PJ6 — GPIO / peripheral function |
| Pino K12 | PJ7 — GPIO / peripheral function |
| Pino L1 | VSS — Ground |
| Pino L2 | PK0 — GPIO / peripheral function |
| Pino L3 | PK1 — GPIO / peripheral function |
| Pino L4 | PK2 — GPIO / peripheral function |
| Pino L5 | VSS — Ground |
| Pino L6 | PK3 — GPIO / peripheral function |
| Pino L7 | PK4 — GPIO / peripheral function |
| Pino L8 | PK5 — GPIO / peripheral function |
| Pino L9 | PK6 — GPIO / peripheral function |
| Pino L10 | PK7 — GPIO / peripheral function |
| Pino L11 | VSS — Ground |
| Pino L12 | PK8 — GPIO / peripheral function |
| Pino M1 | NC — Not connected (per datasheet) |
| Pino M2 | NC — Not connected (per datasheet) |
| Pino M3 | NC — Not connected (per datasheet) |
| Pino M4 | NC — Not connected (per datasheet) |
| Pino M5 | VDDIO — 3.3 V I/O supply |
| Pino M6 | NC — Not connected (per datasheet) |
| Pino M7 | NC — Not connected (per datasheet) |
| Pino M8 | NC — Not connected (per datasheet) |
| Pino M9 | NC — Not connected (per datasheet) |
| Pino M10 | NC — Not connected (per datasheet) |
| Pino M11 | NC — Not connected (per datasheet) |
| Pino M12 | NC — Not connected (per datasheet) |
Aplicações típicas
ATSAME70Q20B-CNT é adequado para 6 aplicaçãos: Industrial Motor Drives (BLDC / PMSM / FOC), Industrial Ethernet Gateway / PLC Controller, High-End Audio Processing / DSP Front-End, Building Automation / HVAC Controller, Connected IoT Edge Nodes / Sensor Hubs, Medical Diagnostic and Monitoring Equipment.
Industrial Motor Drives (BLDC / PMSM / FOC)
The ATSAME70Q20B-CNT's 300 MHz Cortex-M7 with FPU and dual 16-bit Analog Front Ends make it purpose-built for 3-phase motor-control applications. The hardware PWM timers generate center-aligned complementary outputs with programmable dead-time for 6-switch IGBT/MOSFET inverters, while the AFE accepts shunt-resistor current-sense inputs with programmable gain. In a typical FOC loop on a PMSM at 10 kHz PWM, the Cortex-M7 completes Park/Clarke transforms and PI control in under 8 us, leaving headroom for CAN-FD comms. Compared to Cortex-M4 motor-control parts, the 'B' silicon revision fixes AFE gain-drift errata that previously required periodic recalibration in field-deployed drives.
Recomendado
Industrial Ethernet Gateway / PLC Controller
The integrated 10/100 GMAC with IEEE 1588 hardware timestamping, plus dual CAN-FD controllers, positions the ATSAME70Q20B-CNT as a backbone PLC or industrial gateway bridging fieldbus and Ethernet networks. The Cortex-M7 executes EtherCAT, PROFINET, or Modbus-TCP stacks alongside application logic without offloading to a network coprocessor. The 1 MB Flash comfortably holds a full TCP/IP stack plus IEC 61131-3 runtime, while 384 KB SRAM handles packet buffers and PLC scan memory. Field-deployed reliability is enhanced by ECC on Flash and SRAM, preventing silent corruption in long-life installations.
Recomendado
High-End Audio Processing / DSP Front-End
The Cortex-M7's SIMD DSP instructions and double-precision FPU deliver sustained DSP throughput suitable for active-noise-cancellation headphones, professional audio mixers, and multi-channel amplifier control. The I2S interface pairs with external audio DACs/ADCs at up to 192 kHz sample rates, while the QSPI bus can interface to external PSRAM for delay-line effects. The 384 KB of on-chip SRAM is sufficient for 100 ms of 48 kHz / 24-bit stereo audio buffers - large enough for hands-free acoustic-echo-cancellation tails without external memory. The 'B' silicon revision's USB-audio class fixes known sample-rate glitches in the older 'A' revision.
Recomendado
Building Automation / HVAC Controller
Building automation controllers typically combine multiple fieldbus protocols (BACnet, Modbus, KNX) with Ethernet backhaul, exactly the peripheral mix the ATSAME70Q20B-CNT provides. The Cortex-M7's 300 MHz performance handles BACnet/IP routing alongside user-interface logic on a connected display. Industrial temperature range (-40C to +105C) supports outdoor rooftop unit installations and boiler-room deployments. ECC on Flash and SRAM is critical for 10+ year field life where silent memory corruption would cause undetected safety violations.
Recomendado
Connected IoT Edge Nodes / Sensor Hubs
Edge IoT nodes aggregate data from multiple sensor buses (I2C, SPI, UART sensors) and forward over Ethernet or HS-USB to a cloud gateway. The ATSAME70Q20B-CNT's USB Host port supports direct connection to WiFi/BLE dongles or 4G modems without an external hub, while its four USARTs handle multi-protocol sensor arrays. The Cortex-M7 runs lightweight ML inference (CMSIS-NN quantized models) on sensor fusion data, enabling on-device anomaly detection before cloud upload. Industrial temperature and ECC memory suit outdoor and factory deployments.
Recomendado
Medical Diagnostic and Monitoring Equipment
Medical devices such as patient monitors, point-of-care analyzers, and imaging subsystems benefit from the ATSAME70Q20B-CNT's combination of DSP-class math and rich peripherals. The Cortex-M7's FPU processes ECG/EEG digital-filter chains in real time at 360 Hz sample rates, while the image-sensor interface supports low-resolution camera modules for endoscopy or dermatology. ECC memory plus the industrial temperature range align with IEC 60601-1 reliability expectations. Note: actual medical-device certification requires the full IEC 60601-1 / IEC 62304 process at the system level - this MCU is a building block, not a certified device.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAME70Q20B-CNT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAME70Q20B-CN | ATSAME70Q20A-CNT | ATSAME70Q20B-CFNT | ATSAME70N21B-CNT | ATSAME70N20A-CNT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 144-LFBGA (10x10 mm) | 144-LFBGA (10x10 mm) - same | 144-LFBGA (10x10 mm) - same | 144-LFBGA (10x10 mm) - same | 144-LFBGA (10x10 mm) - same | 144-LFBGA (10x10 mm) - same |
| Core Architecture | ARM Cortex-M7 + FPU | ARM Cortex-M7 + FPU | ARM Cortex-M7 + FPU | ARM Cortex-M7 + FPU | ARM Cortex-M7 + FPU | ARM Cortex-M7 + FPU |
| Maximum Clock Speed | 300 MHz | 300 MHz | 300 MHz | 300 MHz | 300 MHz | 300 MHz |
| Flash Memory | 1 MB | 1 MB | 1 MB | 1 MB | 2 MB | 1 MB |
| SRAM | 384 KB | 384 KB | 384 KB | 384 KB | 384 KB | 384 KB |
| Silicon Revision | B (latest, errata-fixed) | B (latest) | A (legacy errata) | B (latest) | B (latest) | A (legacy errata) |
| Operating Temperature | -40C to +105C (industrial) | -40C to +105C | -40C to +105C | -40C to +125C (extended) | -40C to +105C | -40C to +105C |
| Packaging Form | Tape & Reel (TR) | Tray | Tape & Reel | Tape & Reel | Tape & Reel | Tape & Reel |
Principais diferenciais
- Latest 'B' silicon revision fixes USB and AFE errata (vs ATSAME70Q20A-CNT)
- Industrial temperature range with same 144-LFBGA footprint (vs ATSAME70J20B-AN)
- Drop-in scalability to 2 MB Flash within same family (vs ATSAME70N21B-CNT)
Notas de projeto
The 144-LFBGA package has 0.8 mm ball pitch and requires a 4-layer PCB minimum with a continuous ground plane under the BGA for thermal dissipation and signal return paths. Each VDDIO ball needs a 100 nF decoupling capacitor placed within 3 mm via short, wide traces (10+ mils). VDDCORE balls need both 100 nF and 4.7 uF bulk capacitance. Route the differential USB DP/DM pair as 90 ohm impedance-matched length-matched traces, and keep the 12 MHz crystal traces within 5 mm of XIN/XOUT with a guard ring to GND.
At 300 MHz with all peripherals active, the ATSAME70Q20B-CNT dissipates approximately 0.5 W internally. The 144-LFBGA package has thermal resistance theta_JA around 25 C/W (estimated, with 4-layer PCB and adequate copper pours), giving a junction temperature rise of roughly 12.5 C above ambient. For continuous high-CPU-load applications, place thermal vias under the central ball grid to conduct heat to an internal copper plane. Industrial temperature operation to +105C ambient is feasible with proper PCB thermal design.
Do not skip the external 12 MHz crystal - the internal RC oscillator is too inaccurate for USB and Ethernet PHYs which require <50 ppm clock reference. Ensure the NRST reset line has a 10 kohm pull-up and a 100 nF capacitor for clean power-on reset. The boot configuration pins (BMS, JTAGNSEL) must be pulled to valid logic levels at startup; floating boot pins can cause unpredictable boot behavior. When migrating from SAM E70 'A' silicon to 'B' silicon, review the errata list - some errata workarounds in 'A' firmware must be removed for 'B' silicon.
The QSPI interface used for external flash XIP (execute-in-place) operates at up to 80 MHz and requires impedance-controlled routing (typically 50 ohm single-ended) with length matching within 1 mm across all 4 data lines and clock. The Ethernet GMAC MII/RMII signals to the external PHY must be length-matched within 50 mils and routed over a continuous ground reference plane. Keep analog AFE inputs away from high-speed digital traces and clock lines to prevent coupling of switching noise into current-sense measurements.
Informações de conformidade
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - for automotive applications consider ATSAMx70 automotive variants. MSL-3 (168 hours) moisture sensitivity level per JEDEC J-STD-020.
