ATTINY44A-MMH - 20MHz 8-bit AVR MCU | Microchip
N.º da peça: ATTINY44A-MMH ✓ AtivoATTINY44A-MMH Visão geral
A microcontroller is an integrated semiconductor that executes firmware, reads inputs, controls outputs, and manages timing within a complete embedded system. The ATtiny44A belongs to the TinyAVR family and uses an 8-bit AVR enhanced RISC architecture. Its relatively small memory footprint and I/O count suit compact products where the application does not require the storage, processing capacity, or pin count of a larger microcontroller.
Key features include 20 MHz maximum operating frequency, 4 KB of programmable flash, 256 bytes each of EEPROM and SRAM, 12 general-purpose I/O lines, 32 working registers, and two hardware PWM channels. The 20-VQFN package reduces board footprint for space-constrained designs, while in-system programming supports programming and updating through the device programming interface. The industrial-temperature ordering option is identified in product listings for this exact MPN.
The ATtiny44A architecture executes AVR instructions efficiently and supports a broad range of embedded-control tasks. Flash memory holds firmware, SRAM supports working variables and stack operations, and EEPROM provides nonvolatile storage for parameters or calibration data. The two PWM outputs can support motor, LED-brightness, or proportional control functions when the firmware and external power-stage requirements are appropriate.
Typical uses include industrial control modules, compact sensor interfaces, LED lighting controllers, small motor controllers, appliance controls, and low-power embedded products. In each case, the 12 I/O lines, two PWM channels, and 4 KB program space provide a practical resource envelope for coordinated sensing and actuator management without introducing a larger processor or discrete timing circuitry.
PCB design should preserve short, clean power and ground connections, place decoupling capacitors close to the supply pins, and route programming and communications away from sensitive analog inputs. The compact 3 x 3 mm VQFN package also requires careful attention to pad geometry, solder-paste design, thermal-pad assembly, and inspection because short lead spacing makes assembly quality important.
This product overview combines the exact orderable MPN, package, memory, clock, and I/O characteristics with practical design guidance and qualified replacement analysis. It helps engineers identify whether the ATTINY44A has enough resources for an embedded-control design before committing to a compact 20-VQFN PCB layout.
Alternativas drop-in para ATTINY44A-MMH — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATTINY44A-MMH (mesmo formato e footprint) — diferindo em Architecture, General-Purpose I/O Lines, General-Purpose Working Registers, PWM Channels, Package.
ATTINY84A-MMH
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATTINY24A-MMH
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATTINY441-MMH
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATTINY44A-MMH Classificações máximas e características elétricas
| Product Type | 8-bit RISC microcontroller |
| Architecture | AVR enhanced RISC |
| Frequência máxima de clock | 20 MHz |
| Program Flash Memory | 4 KB |
| Program Word Organization | 2K x 16 |
| EEPROM Memory | 256 bytes |
| SRAM Memory | 256 bytes |
| General-Purpose I/O Lines | 12 |
| General-Purpose Working Registers | 32 |
| Timer/Counter | 8-bit timer/counter |
| PWM Channels | 2 |
| Tensão de alimentação de operação | 1.8 V |
| Temperature Grade | Industrial temperature |
| Encapsulamento | 20-VQFN (3 x 3 mm) |
| Package Type | QFN |
| Termination Material | NiPdAu |
| Green Classification | Green |
| Programming | In-system programmable |
Guia de Configuração de Pinos do ATTINY44A-MMH qfn
Configuração de pinos para ATTINY44A-MMH (pacote qfn). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATTINY44A-MMH.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATTINY44A-MMH é adequado para 6 aplicaçãos: Industrial Sensor Interface, LED Lighting Controller, Small Motor Controller, Appliance Control Module, Portable Measurement Product, Security and Access Control.
Industrial Sensor Interface
The ATTINY44A-MMH fits compact sensor-interface modules that need to acquire measurements, apply calibration, and present processed data through a serial or digital interface. Its 12 general-purpose I/O lines provide connections for sensors, indicators, and control signals without requiring a large microcontroller. The 256 bytes of SRAM support short working buffers, while 256 bytes of EEPROM can retain configuration or calibration values across power cycles. At a 20 MHz maximum clock, the AVR core provides more than enough throughput for typical polling, filtering, thresholding, and communication routines. Designers should keep analog traces away from clock and programming nets, use local decoupling, and reserve firmware space for calibration logic and fault handling.
LED Lighting Controller
The ATTINY44A-MMH is appropriate for compact multi-channel LED controllers where dimming, sequencing, and status indication must be coordinated in a small enclosure. Its two hardware PWM channels can generate independent base-frequency duty cycles for two lighting channels, while the remaining I/O lines can control enable signals, drivers, or indicators. The 4 KB of flash is suitable for a focused lighting state machine rather than a large graphical application. Keeping PWM functions on timer-capable pins simplifies deterministic dimming and reduces firmware jitter. The design should verify LED-driver topology, current limits, thermal performance, and whether an external transistor or constant-current driver is required.
Small Motor Controller
The ATTINY44A-MMH can manage a small DC motor or solenoid in compact power-control products. Its two PWM outputs support speed or proportional-control functions, while the 12 I/O lines can accept limit sensors, command inputs, and fault signals. The 20 MHz AVR clock provides useful response margin for closed-loop routines such as edge counting, duty-cycle adjustment, and current limiting. Because the MCU does not directly replace a power MOSFET, relay, or motor driver, the external switching stage must be sized separately. Validate stall current, inductive voltage transients, thermal rise, and startup behavior before connecting the controller to a load.
Appliance Control Module
The ATTINY44A-MMH is well suited to appliance and household-product control modules that coordinate buttons, indicators, relays, and small motors. Four kilobytes of flash can hold focused control firmware, 256 bytes of SRAM can support state variables, and the 12 I/O lines offer enough connectivity for a keypad, status LEDs, and discrete actuators. The 3 x 3 mm VQFN package helps reduce board area where enclosure space is restricted. For safety-related appliance functions, add appropriate fail-safe behavior, input filtering, and electrical isolation where required. Firmware should avoid relying on timing delays alone and should use debounce, watchdog, and diagnostic strategies appropriate to the appliance load.
Portable Measurement Product
The ATTINY44A-MMH can serve as the control component in a compact handheld or battery-operated measurement product. Its 12 I/O lines can support switches, displays, indicators, and external sensing devices, while 256 bytes of EEPROM stores calibration constants or user settings. The 20 MHz clock supports responsive control of short measurement and display sequences without requiring a high-performance processor. For a portable design, operating mode and peripheral shutdown should be managed carefully because final battery life depends on the complete circuit and firmware. A compact PCB also benefits from the small QFN footprint, although exposed-pad soldering, assembly inspection, and thermal management still require process controls.
Security and Access Control
The ATTINY44A-MMH can be incorporated into small access-control peripherals such as keypad readers, lock controllers, credential interfaces, and alarm modules. The 12 I/O lines support buttons, indicators, relays, and communication signals, while the hardware PWM channels can control indicator brightness or simple actuator signaling. Its 4 KB flash capacity fits focused firmware with deliberate memory budgeting. Security-critical products should add authenticated communications where required, protected storage practices, secure boot procedures, and physical tamper considerations rather than relying on the MCU model alone. Validate worst-case input timing, relay transients, and firmware update procedures before production release.
Dados de referência de engenharia para ATTINY44A-MMH — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATTINY84A-MMH | ATTINY24A-MMH | ATTINY441-MMH |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-VQFN (3 x 3 mm) | 20-VQFN (3 x 3 mm) | 20-VQFN (3 x 3 mm) | 20-VQFN (3 x 3 mm) |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| General-Purpose I/O Lines | 12 | 12 | 12 | 12 |
| PWM Channels | 2 | 4 | 2 | 4 |
| Programming | In-system programmable | In-system programmable | In-system programmable | In-system programmable |
| Architecture | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC |
Principais diferenciais
- Balanced memory and peripheral set for compact embedded control (vs ATTINY84A-MMH)
- Two hardware PWM channels support compact dual-channel timing (vs ATTINY84A-MMH)
- Compact 3 x 3 mm VQFN implementation (vs ATTINY24A-MMH)
Notas de projeto
Place the supply decoupling capacitor immediately beside the ATTINY44A-MMH power and ground pins, with the shortest practical ground return to the device. Keep programming, clock, and switching-node routes away from analog inputs. Because the package is only 3 x 3 mm, use a manufacturer-compatible land pattern and verify the exposed-pad connection before fabrication.
Assign timer-capable pins to PWM outputs before finalizing the schematic so the two hardware PWM channels can be used without software bit-banging. Avoid placing sensitive sensor traces beside the exposed pad, programming interface, or fast-switching power circuitry. A short ground plane under the device and a controlled return path will reduce susceptibility to coupling between compact digital and analog sections.
Do not substitute a different ATtiny member based only on the package and clock rate. Pin multiplexing, memory capacity, interrupt assignments, timer channels, and analog peripherals can differ even when the physical package matches. Check the exact MPN suffix, manufacturer pin table, fuse configuration, and firmware resource usage before approving any alternative for production.
Informações de conformidade
The listing identifies the device as Green with NiPdAu termination. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ATTINY44A-MMH ordering code require confirmation from the manufacturer's compliance documentation.