ATTINY461A-XU - 20MHz AVR MCU with 4KB Flash | Microchip
N.º da peça: ATTINY461A-XU ✓ AtivoATTINY461A-XU Visão geral
An 8-bit AVR microcontroller is a compact embedded-processing device built around a RISC architecture and designed to execute firmware that reads sensors, controls actuators, manages power sequencing, or handles communication protocols. Within the semiconductor hierarchy, the ATtiny461A belongs to the AVR family of 8-bit microcontrollers and operates as a system-on-chip containing Flash memory, SRAM, EEPROM, timers, serial interfaces, analog conversion circuitry, and I/O ports.
The ATTINY461A-XU provides 4 KB of Flash for program storage, 256 bytes of EEPROM for nonvolatile data, and 256 bytes of SRAM for working memory. Its 32 working registers support efficient AVR instruction execution, while 16 I/O lines provide interfaces for sensors, switches, indicators, and actuators. The device operates from 1.8 V to 5.5 V according to the published component description, allowing it to fit both low-voltage and conventional 5 V embedded systems.
The ATtiny461A family uses Microchip's enhanced AVR RISC architecture and picoPower technology. Its timer resources support timing and waveform-generation tasks, while its analog-to-digital converter supports measurement of external analog signals. The 20 MHz operating capability provides useful throughput for compact control systems without requiring a larger external processor, although actual execution time depends on the selected clock source and firmware configuration.
Typical uses include industrial sensor nodes, compact motor-control modules, instrumentation front ends, automated switches, lighting controllers, and low-power embedded products. The TSSOP-20 package also makes the controller practical for densely populated PCB layouts where a smaller package than a 28-pin or 40-pin device is useful.
Circuit design should preserve clean analog grounding, place the device input capacitors close to the supply pins, and verify all peripheral pin assignments against the manufacturer pin-description table before PCB routing. Firmware should also account for reset behavior, startup timing, brownout conditions, and the distinction between port pins that serve multiple peripheral functions.
This product record combines the manufacturer family specifications, exact ATTINY461A-XU package identification, sourcing information, same-package alternatives, and application-focused engineering guidance. It is intended to support component selection, PCB planning, firmware planning, and procurement without implying that alternatives with different memory sizes or peripheral configurations are automatically interchangeable.
Alternativas drop-in para ATTINY461A-XU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATTINY461A-XU (mesmo formato e footprint) — diferindo em Package, SRAM.
ATTINY261A-15MU
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATTINY861A-15MU
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATTINY167-A15XZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATTINY461A-XU Classificações máximas e características elétricas
| Product Type | 8-bit RISC microcontroller |
| Architecture | AVR enhanced RISC |
| Frequência máxima de clock | 20 MHz |
| Program Flash Memory | 4 KB |
| Flash Organization | 2K x 16 |
| EEPROM Memory | 256 bytes |
| SRAM | 256 bytes |
| General-Purpose I/O Lines | 16 |
| General-Purpose Working Registers | 32 |
| Timer/Counter | 8-bit timer/counter with compare modes |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Encapsulamento | 20-pin TSSOP |
| Tipo de montagem | Surface mount |
| Temperature Grade | Industrial temperature |
| Programming | In-system programmable Flash |
Guia de Configuração de Pinos do ATTINY461A-XU 20-pin tssop
Configuração de pinos para ATTINY461A-XU (pacote 20-pin tssop). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATTINY461A-XU.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATTINY461A-XU é adequado para 6 aplicaçãos: Industrial Sensor Node, Compact Motor Controller, Instrumentation Front End, Automated Lighting Controller, Battery-Powered IoT Control, Programmable Logic Controller.
Industrial Sensor Node
The ATTINY461A-XU fits compact industrial sensor nodes that acquire an analog input, apply filtering, evaluate thresholds, and report status over a serial link. Its 20 MHz AVR core provides processing headroom, while 4 KB of Flash stores application firmware and 256 bytes of SRAM support short working buffers. The 16 I/O lines allow sensor enable, interrupt, alarm, and communication connections. The 1.8 V to 5.5 V supply range supports both low-voltage sensors and 5 V industrial interfaces, although the ADC configuration and clock should be checked for the selected operating voltage.
Recomendado
Compact Motor Controller
The ATTINY461A-XU can serve as the command processor in a compact motor-control module using its timer and compare functions to generate timing references and control an external driver stage. Sixteen I/O lines leave interfaces for direction commands, fault inputs, position sensors, and status indicators, while the 20 MHz clock supports responsive control firmware. The 4 KB Flash limit favors compact algorithms, so larger motion routines may require another device. Motor current, isolation, protection, and ground-return paths must be engineered separately from the low-voltage microcontroller section.
Recomendado
Instrumentation Front End
In a compact instrumentation front end, the ATTINY461A-XU can manage sensor selection, offset correction, threshold evaluation, and digital reporting. Its ADC-related resources and 16 I/O lines support several analog channels and control signals, while the 20 MHz AVR core allows local processing before data is sent to a host. The 256-byte SRAM is suitable for modest acquisition buffers rather than long waveform histories. Designers should use the manufacturer electrical characteristics to select resistor ranges, reference strategy, and acquisition timing for the required measurement accuracy.
Recomendado
Automated Lighting Controller
The ATTINY461A-XU is suitable for automated lighting modules that combine button or sensor inputs with timer-based dimming, relay control, status indication, and fault detection. Its timer/counter resources support periodic control tasks, and 16 I/O lines provide flexible connections to switches, drivers, and indicators. The device can run from a 1.8 V to 5.5 V control domain, but an appropriate isolated or non-isolated driver stage is required for mains or high-current LED loads. Firmware must include safe startup and shutdown states for every controlled output.
Recomendado
Battery-Powered IoT Control
The ATTINY461A-XU can serve as the local controller in a small battery-powered IoT node that wakes for sensor readings, performs threshold logic, and controls a low-power radio or indicator. Its compact 20-pin TSSOP package leaves board area for the power system and radio, while picoPower characteristics support designs that spend substantial time idle. The 1.8 V minimum supply allows operation from low-energy rails, and 4 KB of Flash accommodates concise control firmware. Actual battery life depends on the clock, ADC usage, sleep configuration, radio behavior, and leakage of the complete board.
Recomendado
Programmable Logic Controller
The ATTINY461A-XU can implement a small programmable logic or sequence controller for equipment with discrete inputs and outputs. Sixteen I/O lines support buttons, selectors, interlocks, status LEDs, and actuator commands, while its timer resources coordinate timing sequences. Firmware can implement debouncing, state transitions, delays, fault latching, and communication reporting within the 4 KB Flash budget. Because the package is only 20 pins, pin multiplexing must be reviewed carefully. Production designs should also include brownout behavior, safe output defaults, and recovery after power interruption.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATTINY461A-XU — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATTINY261A-15MU | ATTINY861A-15MU | ATTINY167-A15XZ |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| Core Processor | 8-bit AVR enhanced RISC | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Program Flash Memory | 4 KB | 2 KB | 8 KB | 16 KB |
Principais diferenciais
- Balanced embedded resource configuration (vs ATTINY261A-15MU)
- More compact firmware storage than the 861A option (vs ATTINY861A-15MU)
- Lower Flash demand than the 16 KB alternative (vs ATTINY167-A15XZ)
Notas de projeto
Route the TSSOP-20 footprint with the pin-1 orientation defined by the manufacturer package drawing and verify every programmable pin against the selected peripheral configuration. Keep traces to ADC inputs short, provide a quiet ground reference near the device, and place decoupling capacitors close to the supply and ground pins. Because many port functions are multiplexed, finalize the pin plan before routing rather than assigning signals after layout.
Budget the complete-board power budget rather than the microcontroller alone. The ATTINY461A-XU supports a 1.8 V to 5.5 V supply range, but the permitted clock and analog performance can depend on operating voltage. Select the regulator for the required rail, maintain local decoupling, and verify brownout behavior so the controller does not enter an undefined state during supply transitions.
Do not treat a matching TSSOP footprint as proof of drop-in compatibility. When evaluating ATTINY261A-15MU, ATTINY861A-15MU, or ATTINY167-A15XZ, compare Flash size, SRAM, EEPROM, timer channels, ADC channels, USART resources, interrupt vectors, fuse configuration, and every alternate-function pin. Existing firmware may also require changes because register locations and peripheral availability are not identical across all three related devices.
For analog measurements, use the manufacturer guidance for the ADC reference, input impedance, sample timing, and source impedance. Add local filtering only after accounting for ADC sampling behavior, and avoid routing measurement inputs beside fast-switching or high-current traces. Use a dedicated, low-impedance ground path from the device ground pin to the analog source when the board combines sensing and switching functions.
Informações de conformidade
The product description identifies the ATTINY461A as an industrial-temperature AVR microcontroller, but it does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.