BCM5481A2KFBG - 1GbE Copper PHY | Broadcom | Networking
N.º da peça: BCM5481A2KFBG ✗ Fim de vidaBCM5481A2KFBG Visão geral
A Gigabit Ethernet PHY is the physical-layer device that converts between a MAC controller's digital data and signals suitable for twisted-pair cabling. In the networking hierarchy, a PHY is a transceiver interface integrated circuit used with a media-access controller, Ethernet switch, router, gateway, or other equipment requiring 10/100/1000BASE-T copper connectivity. The BCM5481A2KFBG therefore handles the physical encoding, signaling, and cable-facing functions while the MAC supplies packet data through RGMII.
Key features include support for 10, 100, and 1000BASE-T operation, a 1000 Mbps data rate, an RGMII interface, CMOS construction, and a peak reflow temperature of 260°C. Its single-port architecture suits one copper Ethernet port per device. The 100-terminal rectangular BGA package permits dense board placement, but it also requires a multilayer PCB with conventional via-in-pad or fanout construction, controlled solder paste printing, and careful inspection of hidden joints.
The part is positioned for copper Ethernet links in routers, switches, gateways, set-top equipment, industrial networking products, and embedded systems. RGMII provides a parallel MAC-facing connection that can reduce pin count compared with a fully parallel GMII implementation at Gigabit rates. During board design, engineers should preserve the exact reference network, power distribution, grounding, and high-speed clock topology specified by the Broadcom datasheet because PHY performance depends on controlled impedance and low-noise power delivery.
Typical implementation places the BCM5481A2KFBG between a RGMII-capable MAC or Ethernet controller and an integrated magnetic module leading to an RJ45 connector. The PHY is used only for copper media; optical-fiber links require a different physical-layer device. System firmware must also configure the PHY through the applicable management interface and validate autonegotiation, link speed, duplex mode, and cable diagnostics.
A primary design consideration is BGA assembly. The package has 100 terminals and a 260°C peak reflow rating, but its fine pitch requires stencil design, profile control, and inspection methods suitable for large-array BGAs. Copper pours should provide both electrical return paths and thermal spreading, while analog supply and digital circuitry should be separated according to the manufacturer's layout guidance.
This product overview consolidates the confirmed device identity, package information, interface characteristics, sourcing answers, replacement boundaries, and practical PCB considerations. It also distinguishes a same-family MPN change from true pin-compatible alternatives, helping engineers shorten component search and qualification time while preserving the risk controls required for an advanced BGA networking device.
Alternativas drop-in para BCM5481A2KFBG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
BCM5481A1KFBG
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BCM5481A2KFBG Classificações máximas e características elétricas
| Product Type | Single-port Gigabit Ethernet PHY transceiver |
| Supported Copper Standards | 10/100/1000BASE-T |
| Maximum Data Rate | 1000 Mbps |
| MAC Interface | RGMII |
| Ethernet Compliance | IEEE 802.3 |
| Port Count | 1 copper port |
| Technology | CMOS |
| Package Type | Rectangular grid-array BGA |
| Terminal Count | 100 terminals |
| Tipo de montagem | Surface mount |
| Peak Reflow Temperature | 260°C |
| Halogen-Free Status | Not compliant |
Guia de Configuração de Pinos do BCM5481A2KFBG rectangular grid-array bga
Configuração de pinos para BCM5481A2KFBG (pacote rectangular grid-array bga). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para BCM5481A2KFBG.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
BCM5481A2KFBG é adequado para 6 aplicaçãos: Industrial Ethernet Router, Managed Ethernet Switch Port, Set-Top Box Gateway, Embedded Control System, Network Security Gateway, Industrial Sensor Gateway.
Industrial Ethernet Router
The BCM5481A2KFBG fits a single-port industrial router that must support 10, 100, or 1000 Mb/s links over twisted-pair copper. Its RGMII interface connects the PHY to a compatible Ethernet MAC, while its confirmed 1000 Mbps capability supports high-throughput gateway and routing designs. The PHY is placed on the line side of an Ethernet magnetic module leading to an RJ45 or ruggedized connector. The 100-terminal BGA requires a multilayer PCB, but its fine-pitch construction can reduce board area compared with a larger leaded transceiver. Firmware must support the PHY's initialization, autonegotiation, and link-monitoring functions, while the layout must preserve controlled clock and RGMII signal integrity.
Recomendado
Managed Ethernet Switch Port
The BCM5481A2KFBG is suitable for a managed switch line card requiring one 10/100/1000BASE-T copper port. Its 1000 Mbps data rate provides a full-rate Gigabit option, and RGMII enables connection to a switching ASIC or MAC through a compact parallel interface. The device can support copper links at 10, 100, or 1000 Mb/s, allowing automatic negotiation with legacy endpoints. Its primary PCB concern is that the 100-terminal BGA demands controlled assembly and via-in-pad or escape routing. Designers should follow the Broadcom layout for clock generation, analog supply separation, decoupling, and RGMII impedance matching to sustain reliable operation across supported cable conditions.
Recomendado
Set-Top Box Gateway
The BCM5481A2KFBG can provide copper Ethernet connectivity in a set-top box or home gateway requiring a single 10/100/1000BASE-T port. The RGMII interface reduces the connection burden to a compatible MAC, and the PHY handles the physical layer for copper media rather than optical links. Its 100-terminal BGA package supports compact board layouts in space-conscious consumer equipment. Implementation requires a properly designed Ethernet magnetic path, separate low-noise supply routing, and a PCB stack that supports the manufacturer's high-speed escape-routing requirements. Software should validate PHY detection, negotiated speed, duplex operation, and recovery after cable changes to maintain reliable service across the three supported BASE-T rates.
Recomendado
Embedded Control System
The BCM5481A2KFBG is applicable to an embedded control system that adds a wired Gigabit Ethernet service port alongside a real-time controller. A RGMII-capable network processor or MAC can exchange frames with the PHY, supporting copper connectivity at 10, 100, or 1000 Mb/s for configuration transfer, diagnostics, and supervisory data. The single-port topology avoids unnecessary PHY channels when only one cable interface is required. Because the component uses a 100-terminal BGA, the embedded board must use a controlled assembly process, adequate via density, and thermal copper. The design should also isolate Ethernet magnetics from sensitive analog sections and validate operating-temperature requirements before releasing the equipment for industrial deployment.
Recomendado
Network Security Gateway
The BCM5481A2KFBG can serve as the copper Ethernet physical layer in a network security gateway that provides one administrative or downstream port. Its RGMII interface supports integration with a network processor, and its 10/100/1000BASE-T support allows compatibility with management terminals and access devices operating at different link rates. The PHY should be connected through a network magnetic module with the layout and component values defined by the Broadcom design guidance. Secure systems also need careful power filtering and controlled return paths to reduce coupling from switching circuitry into the Ethernet front end. Firmware configuration should include deterministic link checks and error handling to support controlled recovery after cable or endpoint disturbances.
Recomendado
Industrial Sensor Gateway
The BCM5481A2KFBG fits an industrial sensor gateway that aggregates local sensor traffic and provides a wired copper uplink. Its single-port Gigabit PHY supports three nominal operating rates, allowing the gateway to connect reliably to plant networks or engineering workstations using 10, 100, or 1000 Mb/s. The RGMII interface connects to a suitable gateway processor, while the copper PHY occupies the physical layer between that processor and an isolation network module. Because the package is a 100-terminal BGA, the gateway board should provide adequate escape routing, layer transitions, and copper thermal relief. The complete assembly must be evaluated for temperature range, vibration, and long-term copper-link reliability under industrial environmental conditions.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BCM5481A2KFBG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | BCM5481A1KFBG |
|---|---|---|
| Brand | Broadcom | Broadcom |
| Package | 100-terminal rectangular BGA | 100-terminal rectangular BGA |
| Product Family | BCM5481 | BCM5481 |
| Silicon Revision Code | A2 | A1 |
| Port Configuration | Single-port | Single-port |
Principais diferenciais
- Closest identified package-matched Broadcom alternative (vs BCM5481A1KFBG)
- Single-port design limits board area (vs Multi-port Ethernet PHY designs)
- Gigabit-rate copper connectivity (vs 100 Mb/s-only Ethernet PHYs)
Notas de projeto
Implement the 100-terminal BGA on a multilayer PCB using the Broadcom land pattern, ball-pitch dimensions, and stackup guidance. Confirm whether the design uses via-in-pad or component-side escape routing, and define the solder-mask and paste apertures for a 260°C peak-reflow assembly. Do not derive the footprint solely from a generic BGA library because ball-map changes can create hidden connectivity or short-circuit risks.
Route RGMII and its clock as controlled-impedance interfaces with the shortest practical connections and the reference plane identified in the manufacturer's layout guidance. Keep PHY supply and ground planes continuous, place decoupling close to the relevant pins, and separate noisy digital or switching-converter return currents from the Ethernet analog section. Confirm signal and return-path continuity across every layer transition.
Do not treat every cross-reference MPN as a drop-in replacement. BCM5481A1KFBG is the closest identified same-family candidate, but the A1 and A2 revisions still require comparison of the datasheet, errata, initialization procedure, and management registers. LAN8820I-ABZJ, VSC8211VW, and other listed equivalents use manufacturer-specific packages and interfaces, so they require a PCB and firmware review rather than a simple last-time-buy substitution.
Finalize supply rails and decoupling only from the manufacturer electrical tables, including voltage tolerance, startup behavior, and current at 10, 100, and 1000 Mb/s operating modes. Place bulk and local ceramic decoupling according to the reference design, then verify the assembled board for acceptable noise at the PHY, magnetic module, and RJ45 return paths. Avoid adding large capacitors or ferrite components that could alter the required power or signal network.
Informações de conformidade
The cross-reference record identifies the device as halogen-free not compliant and estimates an end-of-life date in 2026. RoHS, REACH, lead-free, and conflict-minerals status were not established from a manufacturer declaration.