BCM5482SA2KFB - Dual-Port 10/100/1000BASE-T PHY | Broadcom
N.º da peça: BCM5482SA2KFB ✓ AtivoBCM5482SA2KFB Visão geral
An Ethernet physical-layer transceiver, commonly called a PHY, converts serialized digital data into electrical signaling for transmission over twisted-pair copper cables. The BCM5482SA2KFB belongs to the PHY hierarchy within Ethernet interface ICs, which connect a digital MAC or network processor to physical copper media. Supporting 10, 100, and 1000 Mb/s allows one device to serve multiple speed requirements within a dual-port design.
The principal feature of the BCM5482SA2KFB is integration of two 10/100/1000BASE-T ports in one component. This can reduce the number of separate Ethernet PHY devices required in a network interface, switch, router, or industrial controller. Its multi-rate support also allows equipment to negotiate the highest common link speed supported by both connected devices rather than requiring separate interfaces for Fast Ethernet and Gigabit Ethernet.
As an Ethernet interface IC, the BCM5482SA2KFB is intended to support copper-based data links used in local-area networks. Its two-port architecture is useful where board space is constrained but two independent network connections are needed. Compared with a single-port PHY arrangement, a dual-port device can simplify routing and component placement, although the final signal-integrity design still depends on the magnetic interface, connector layout, cable requirements, and impedance-controlled PCB construction.
Typical applications include industrial Ethernet switches, routers, network interface controllers, embedded communication equipment, and control systems with multiple copper Ethernet ports. The 10/100/1000BASE-T capability makes the part relevant to factory automation, building controls, network appliances, test equipment, and embedded platforms that must accommodate legacy 10 Mb/s or 100 Mb/s links as well as Gigabit Ethernet connections.
Use the manufacturer datasheet's pin-description and reference-circuit sections when assigning power, ground, clock, digital-interface, and analog-network signals. High-speed copper pairs require controlled impedance and careful separation from noisy digital or switching-converter paths. Component placement and magnetic-interface design should be reviewed against the manufacturer's layout guidance before production, especially when two high-speed ports share a compact board area.
This product page organizes the available BCM5482SA2KFB information, identifies same-family Broadcom candidates, and provides engineering-focused selection guidance. Confirm package, pinout, clock requirements, register programming, power sequencing, environmental limits, and lifecycle status against the exact Broadcom datasheet and ordering information before committing a design to production.
Alternativas drop-in para BCM5482SA2KFB — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
BCM5482SA2KFBG
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BCM5482SEA2KFBG
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BCM5482SA2KFB Classificações máximas e características elétricas
| Product Type | Dual-port 10/100/1000BASE-T Ethernet PHY |
| Manufacturer | Broadcom Limited |
| Number of Ports | 2 ports |
| Supported Data Rates | 10 Mb/s, 100 Mb/s, and 1000 Mb/s |
| Ethernet Standards | 10/100/1000BASE-T |
| Physical Medium | Twisted-pair copper Ethernet |
| Port Architecture | Dual port |
| Interface Classification | Ethernet physical-layer transceiver |
Guia de Configuração de Pinos do BCM5482SA2KFB standard
Configuração de pinos para BCM5482SA2KFB (pacote standard). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para BCM5482SA2KFB.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
BCM5482SA2KFB é adequado para 6 aplicaçãos: Industrial Ethernet Switch, Industrial Router, Embedded Network Controller, Building Automation Gateway, Network Test Equipment, Network Appliance.
Industrial Ethernet Switch
The BCM5482SA2KFB fits a compact industrial switch that needs two copper Ethernet links. Its dual 10/100/1000BASE-T capability allows each port to negotiate among 10 Mb/s, 100 Mb/s, and 1000 Mb/s, which supports both legacy devices and modern high-speed equipment on the same board. The device can simplify front-panel port implementation compared with two separate single-port PHYs. Board design must still provide approved magnetic interfaces, controlled-impedance differential pairs, proper isolation, and the power and clocking architecture required by the exact Broadcom datasheet.
Recomendado
Industrial Router
The BCM5482SA2KFB is suitable for an industrial router or gateway with two copper Ethernet interfaces. Supporting 10BASE-T, 100BASE-T, and 1000BASE-T on both channels allows the equipment to connect to management networks, controllers, and plant-floor systems operating at different speeds. Two integrated PHYs can reduce the number of separate transceiver components, but the host processor must provide a compatible digital interface and clocking arrangement. Validate magnetics, isolation, surge exposure, thermal performance, and cable reach against the manufacturer reference design.
Recomendado
Embedded Network Controller
The BCM5482SA2KFB can provide two physical copper-network connections for an embedded Linux controller, automation processor, or communications appliance. A multi-rate PHY supports legacy 10 Mb/s and 100 Mb/s links as well as 1 Gb/s links without assigning separate copper PHYs to each speed. The controller still requires the appropriate host bus, interrupt, reset, clock, and firmware configuration described in the exact datasheet. Layout should isolate the high-speed copper interface from processor supplies and digital timing paths.
Recomendado
Building Automation Gateway
The BCM5482SA2KFB fits a building-automation gateway needing wired Ethernet connectivity on two ports. One channel can serve a local controller or service network while the other connects to a building LAN, and 10/100/1000BASE-T support accommodates widely varying equipment capabilities. Because building gateways may connect to long cable runs or mixed legacy networks, verify supported media, auto-negotiation behavior, isolation, and electrostatic-discharge requirements in the Broadcom documentation. Keep copper-pair routing away from switching regulators and relay-control paths.
Recomendado
Network Test Equipment
The BCM5482SA2KFB is applicable to network test equipment requiring two independently instrumented 10/100/1000BASE-T interfaces. Multi-rate support allows the same hardware to test legacy and Gigabit Ethernet links, while the two-port arrangement supports loopback, endpoint, and traffic-generation configurations. Measurement accuracy and protocol testing depend on the surrounding host electronics, magnetic network interface, clocks, and firmware rather than the PHY alone. Confirm the exact electrical characteristics and reference configuration before using the device in calibrated test paths.
Recomendado
Network Appliance
The BCM5482SA2KFB is useful in compact network appliances, gateways, and edge devices that expose two copper Ethernet connections. Supporting 10, 100, and 1000 Mb/s preserves compatibility with older management devices while supporting Gigabit Ethernet for primary traffic. Integration reduces the physical footprint required for dual-port Ethernet connectivity, subject to confirming the package and thermal design. Production implementation should follow the manufacturer's recommended magnetics, controlled-impedance geometry, power filtering, and isolation spacing to preserve signal integrity.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BCM5482SA2KFB — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | BCM5482SA2KFBG | BCM5482SEA2KFBG |
|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom |
| Port Count | 2 ports | 2 ports | 2 ports |
| Supported Data Rates | 10 Mb/s, 100 Mb/s, and 1000 Mb/s | 10 Mb/s, 100 Mb/s, and 1000 Mb/s | 10 Mb/s, 100 Mb/s, and 1000 Mb/s |
| Ethernet Support | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T |
| Physical Medium | Twisted-pair copper Ethernet | Twisted-pair copper Ethernet | Twisted-pair copper Ethernet |
| Ordering Suffix | SA2KFB | SA2KFBG; final suffix function is not quantified | SEA2KFBG; S/A segment differs from the target |
Principais diferenciais
- Two integrated multi-rate copper ports (vs A conventional single-port Ethernet PHY)
- One device supports three Ethernet rates (vs Single-rate 10BASE-T or 100BASE-T interface)
- Dual-port integration reduces board-level PHY count (vs Two discrete single-port PHYs)
Notas de projeto
Route each 1000BASE-T differential pair as a controlled-impedance structure and follow the manufacturer's recommended pair geometry, spacing, and via rules. Keep the PHY-to-magnetics path short, place magnetics close to the connector when the reference design specifies that arrangement, and avoid stubs. Two adjacent ports require deliberate partition spacing so crosstalk and connector or magnetics-related discontinuities do not degrade the high-speed return loss and insertion-loss targets.
Implement separate filtering paths for the PHY's analog and digital supply domains as shown in the manufacturer reference circuit. Place the required bulk and high-frequency decoupling capacitors close to their associated power pins, with short ground returns and a low-impedance ground plane. Confirm the permitted voltage, sequencing, current limits, and exposed-pad connection in the exact datasheet before selecting regulators or setting undervoltage thresholds.
Preserve the reference clock and high-speed digital interface by keeping them away from the copper-pair and magnetics area. Use the manufacturer's specified clock source, jitter expectations, grounding, and termination arrangement rather than inferring them from a generic Ethernet design. Review crosstalk, return loss, insertion loss, and cable reach for all three supported data rates, with particular attention to 1000BASE-T operation.
Do not treat a similar Broadcom suffix as automatically interchangeable. Confirm the exact package, pinout, order code, electrical ratings, interface mode, and environmental qualification for BCM5482SA2KFB, BCM5482SA2KFBG, or BCM5482SEA2KFBG. Also avoid approving a footprint from the product description alone; obtain the current package drawing and land pattern for the exact manufacturing suffix.
Informações de conformidade
Compliance attributes were not identified in the available product information. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status from Broadcom's current product declaration for the exact MPN.