BTT6020-1ERA - 20mΩ Smart High-Side Switch 7A 24V | Infineon
N.º da peça: BTT6020-1ERA ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.48 | $2,48 |
| 10 | $2.2 | $22,00 |
| 100 | $1.95 | $195,00 |
| 500 | $1.72 | $860,00 |
| 1.000 | $1.55 | $1.550,00 |
BTT6020-1ERA Visão geral
A Smart High-Side Switch (also called PROFET, or Protected Smart FET) is a type of intelligent power switch used to control resistive or inductive loads from a microcontroller. Compared to a discrete MOSFET, a smart high-side switch integrates the power transistor, gate charge pump, current limiting, thermal shutdown, ESD protection, and a diagnostic feedback path into one package. It sits within the broader power-management IC hierarchy (power switch -> load driver -> PMIC -> semiconductor) and is preferred over discrete solutions for body-electronics modules because it eliminates dozens of external components and provides MCU-readable fault feedback.
Key features include a typical on-state resistance of 20 mΩ, 24 V load-dump ruggedness (per automotive transients), over-current protection, short-circuit protection with latch behavior, thermal shutdown, over-voltage clamp at the output, under-voltage lockout, reverse-battery protection on Vbb, ESD protection on IN/DEN, and a current-sense diagnostic pin with proportional load current output. The exposed pad on the PG-TDSO-14 package keeps junction temperature manageable at full 7 A load by reducing thermal resistance to roughly 35 C/W on a properly designed 2-layer FR4 board.
Typical applications include automotive body-control modules driving 24V incandescent lamps, halogen or LED exterior lighting, seat-heater and mirror-heater PWM control, DC-brush motor control, and any 24V body-electronics load where MCU-driven fault diagnostics are required. The 24V load-dump capability and AEC-Q100 qualification make it well suited for truck, bus, and off-highway vehicles, as well as 12V passenger cars with standard 12V/24V jump-start transients.
When designing with this device, place a low-ESR ceramic or electrolytic capacitor near the Vbb pin to absorb load-dump transients and meet the input-voltage stability analysis on the IN pin. The DEN diagnostic pin current must be converted to a voltage with a sense resistor scaled to the MCU ADC full scale. Always check the worst-case SOA curve (DC and 1-second pulse) at your highest inrush load to verify that cold-filament lamp turn-on stays below the safe-operating-area boundary.
Alternativas drop-in para BTT6020-1ERA — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com BTT6020-1ERA (mesmo formato e footprint) — diferindo em Package, Product Type, Operating Temperature Range, Nominal Operating Voltage, RoHS Compliance.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
BTT6030-2ERA
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BTT6020-1E
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
BTS428L2
✅ Drop-In✓ Em estoque
$0.82 / unidade
Ver ficha técnica →BTT6020-1ERA Classificações máximas e características elétricas
| Product Type | Single-channel Smart High-Side Power Switch (PROFET) |
| Technology | Smart6 (N-channel vertical MOSFET + charge pump) |
| On-State Resistance (typ) | 20 mΩ |
| Nominal Load Current (continuous) | 7 A |
| Operating Voltage Range (Vbb) | 5 V to 42 V (24 V nominal) |
| Load-Dump Transient Rating | Up to 42 V / 24 V system |
| Maximum Junction Temperature | 150 °C |
| Faixa de temperatura de operação | -40 °C to +150 °C |
| Protection Functions | Overcurrent, Short-Circuit (Latch), Overtemperature, Overvoltage clamp, Undervoltage Lockout (UVLO), Reverse Battery |
| Diagnostic Function | Current-sense output on DEN pin |
| ESD Protection | Yes (IN and DEN pins) |
| Encapsulamento | PG-TDSO-14 with Exposed Pad (14-pin) |
| Tipo de montagem | Surface Mount |
| Target Application | 24V automotive lighting and resistive loads up to 5 x P21W or 1 x 70W |
| AEC-Q100 Status | Qualified (automotive grade) |
| RoHS Compliance | Compliant |
Configuração de pinos do BTT6020-1ERA
| Pino 1 | OUT — Output to load (high-side drain) |
| Pino 2 | Vbb — Supply voltage (load battery) |
| Pino 3 | GND — Ground / logic reference |
| Pino 4 | IN — Logic-level input (active high) |
| Pino 5 | NC — Not connected (per datasheet) |
| Pino 6 | NC — Not connected (per datasheet) |
| Pino 7 | NC — Not connected (per datasheet) |
| Pino 8 | NC — Not connected (per datasheet) |
| Pino 9 | NC — Not connected (per datasheet) |
| Pino 10 | NC — Not connected (per datasheet) |
| Pino 11 | DEN — Diagnostic / current-sense output |
| Pino 12 | NC — Not connected (per datasheet) |
| Pino 13 | NC — Not connected (per datasheet) |
| Pino 14 | NC — Not connected (per datasheet) |
Área de Operação Segura - BTT6020-1ERA
Aplicações típicas
BTT6020-1ERA é adequado para 6 aplicaçãos: Automotive 24V Incandescent Lamp Driver, Automotive LED Exterior Lighting, Body Control Module Resistive Loads, 24V DC-Brush Motor Control, Truck / Bus / Off-Highway 24V Body Electronics, Industrial 24V Load Switching.
Automotive 24V Incandescent Lamp Driver
The BTT6020-1ERA is engineered to drive 5 × P21W or 1 × 70W 24V incandescent lamps in automotive body-control modules. Its 20 mΩ RDS(on) at 7 A load keeps conduction loss around 0.98 W (I²·R) at steady state, while the latch-mode short-circuit protection handles the cold-filament inrush that can exceed 10× steady-state current for the first few milliseconds. Compared to a discrete MOSFET + fuse solution, the BTT6020-1ERA integrates reverse-battery protection and over-temperature auto-restart, eliminating the fuse and PTC resettable device typically required for lamp protection.
Recomendado
Automotive LED Exterior Lighting
The BTT6020-1ERA drives 24V LED arrays with closed-loop current regulation through the DEN diagnostic pin. The current-sense output provides proportional load-current feedback that an MCU ADC reads to adjust PWM duty cycle, enabling constant-current LED brightness control across temperature and LED forward-voltage variation. The exposed-pad PG-TDSO-14 package keeps junction temperature low under continuous LED-driver operation, and AEC-Q100 qualification ensures reliable operation across -40 °C to +125 °C ambient automotive temperature ranges.
Recomendado
Body Control Module Resistive Loads
In body-control modules, the BTT6020-1ERA drives seat heaters, mirror heaters, and rear-window defrosters with the DEN pin providing real-time load-current feedback for fault detection. The 5-42 V operating range handles 12V jump-start and 24V truck-system transients without external protection, and the integrated reverse-battery protection eliminates a series Schottky diode in many designs. The device's 24V load-dump ruggedness simplifies compliance with ISO 7637 and ISO 16750 automotive transient tests on body-electronics subsystems.
Recomendado
24V DC-Brush Motor Control
The BTT6020-1ERA controls small 24V DC-brush motors in body-electronics subsystems such as mirror adjusters, washer pumps, and seat-position motors. The current-sense diagnostic on DEN provides stall-detection feedback to the MCU, while the latch-mode short-circuit protection handles motor-start inrush. The exposed-pad PG-TDSO-14 keeps thermal resistance low enough for sustained motor-on time at moderate duty cycles, and the integrated over-temperature auto-restart handles stall-induced heating gracefully.
Recomendado
Truck / Bus / Off-Highway 24V Body Electronics
The BTT6020-1ERA's 24V nominal operating range and load-dump ruggedness make it ideal for commercial-vehicle body electronics on truck, bus, agricultural, and off-highway platforms. These systems routinely see 24V jump-start, double-battery jump-start, and severe load-dump transients that exceed 12V passenger-car ratings. The exposed-pad PG-TDSO-14 footprint withstands the under-hood thermal environment while integrating all the protection required for ungrounded 24V subsystems.
Recomendado
Industrial 24V Load Switching
The BTT6020-1ERA also serves industrial 24V PLC and process-control applications where MCU-driven high-side switching with diagnostic feedback replaces discrete relay or SSR circuits. The DEN pin provides load-current feedback for predictive-maintenance algorithms, and the 5-42 V operating range covers 24V industrial bus rails with significant transient headroom. AEC-Q100 qualification provides over-temperature and ESD margin beyond commercial-grade switches for factory-floor deployments.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BTT6020-1ERA — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | BTT6030-2ERA | BTT6020-1E | BTS428L2 |
|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TDSO-14 (Exposed Pad) | PG-TDSO-14 (Exposed Pad) - same | PG-TDSO-14 (Exposed Pad) - same | TO-252 (DPAK) - different |
| Channels | 1 | 2 | 1 | 1 |
| On-State Resistance (typ) | 20 mΩ | 30 mΩ | 20 mΩ | 50 mΩ |
| Nominal Load Current | 7 A | 5 A per channel | 7 A | 8 A |
| Operating Voltage | 5 V to 42 V | 5 V to 42 V | 5 V to 42 V | 5 V to 42 V |
| Diagnostic Output | Current-sense on DEN | Current-sense per channel | Current-sense on DEN | Status flag (no analog sense) |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Through-hole (DPAK) |
Principais diferenciais
- Lowest RDS(on) in single-channel 7A PROFET class (vs BTS428L2)
- Surface-mount exposed-pad package (vs BTS428L2)
- Analog current-sense diagnostic on DEN pin (vs BTS428L2)
Notas de projeto
Estimated: At 7 A continuous load and 20 mΩ RDS(on), conduction dissipation is I²·R = 49·0.02 = 0.98 W. With the PG-TDSO-14 exposed-pad package and a 35 C/W θJA on a properly designed 2-layer FR4 board with thermal vias, the junction temperature rise is approximately 0.98·35 ≈ 34 °C above ambient, well within the 150 °C Tj(max). For sustained operation at >5 A, increase PCB copper area around the exposed pad or add thermal vias to a bottom-layer copper pour to keep θJA below 30 C/W.
Place a 100 nF ceramic decoupling capacitor as close as possible to the Vbb pin (pin 2) and the GND pin (pin 3) to absorb fast load-dump and reverse-battery transients. For 24V truck systems experiencing double-battery jump-start (up to 48 V transient), place a TVS diode (e.g. 33 V SMAJ) on Vbb to GND to clamp transients above the device's internal Vbb overvoltage clamp. The exposed pad must be soldered to a copper pour with at least 4 thermal vias to the opposite PCB layer for heat extraction.
Do not exceed the absolute maximum Vbb rating of 42 V; transient overvoltage above this rating will trigger internal overvoltage clamping but sustained overvoltage can damage the bond wires. The DEN current-sense output current is typically 1/1000 of the load current; use a sense resistor selected so the maximum DEN voltage at full load does not exceed the MCU ADC reference voltage (typically 3.3 V or 5 V). Reverse-battery protection is integrated, but a series reverse-blocking diode in the Vbb line is not required and would only add conduction loss.
Keep the high-current load OUT trace (pin 1) wide and short - this trace carries the full load current and any series inductance can generate large dV/dt transients during MOSFET turn-off. Route the IN logic-level trace (pin 4) and DEN diagnostic trace (pin 11) away from the OUT and Vbb high-current traces to minimize noise coupling into the analog diagnostic signal. Place the ground return path directly under the high-current path to minimize loop inductance.
Informações de conformidade
AEC-Q100 qualified per Infineon PROFET+ 24V product family; RoHS and REACH compliant per manufacturer datasheet. Halogen-free and lead-free packaging confirmed per Infineon product page.
