Texas Instruments

CD40160BE - 4-Bit Synchronous Decade Counter | Texas Instruments

N.º da peça: CD40160BE ✓ Ativo
3 V to 18 V Vdss DIP Package Synchronous Speed
MOQ: 1 |

CD40160BE Visão geral

Texas Instruments CD40160BE is a CMOS synchronous programmable 4-bit decade counter with asynchronous clear, operating from a 3 V to 18 V supply and housed in a 16-pin PDIP package. It counts in BCD decades from 0 through 9 and provides four parallel decade-counter outputs for digital clocks, event counters, and programmable timing systems.

A synchronous decade counter is a logic IC that advances all registered output bits on the active clock edge. The CD40160BE belongs to the CD4000 CMOS logic family, placing it within the hierarchy of CMOS logic IC, counter, decade counter, and digital logic IC. Unlike asynchronous ripple counters, its synchronous architecture prevents ripple-related timing uncertainty between internal count stages, making the output states more predictable for downstream decoding and control logic.

The counter supports programmable decade operation through its load, count-enable, and asynchronous-clear controls. These controls allow the count sequence to be loaded, held, cleared, or advanced under external logic. The 4-bit parallel outputs expose the current BCD decade state, while the asynchronous clear input provides a direct method for resetting the count independently of the clock state. Its CMOS implementation also supports operation across a wide supply-voltage range suitable for both legacy 5 V systems and modern low-voltage digital control.

The Texas Instruments product family documentation identifies CD40160B as a CMOS synchronous programmable 4-bit decade counter with asynchronous clear. The E suffix identifies the military-temperature product in a 16-pin PDIP package. According to the manufacturer family documentation, CD40160B is functionally equivalent to and pin-compatible with the 74LS160 TTL counter family, allowing designers to compare CMOS and TTL implementations when upgrading legacy equipment.

Typical uses include decade-based digital clocks, sequential industrial timers, laboratory counters, pulse-counting modules, and embedded timing controllers. Because the outputs represent decimal decades rather than unrestricted binary values, the device is especially useful when the next stage must display or control a decimal count. The external load and enable inputs also permit cascading or coordinating multiple counting channels in larger equipment.

For reliable operation, keep the asynchronous clear and control inputs away from noisy switching paths, and observe the manufacturer’s specified input transition limits. Confirm signal levels, clock pulse width, and supply decoupling against the CD40160B datasheet before using the counter with modern 3.3 V logic. The DIP package also requires adequate spacing and routing around the through-hole footprint on legacy-style boards.

This page combines the CD40160BE function, pin-compatible TTL-counter relationship, practical implementation guidance, and qualified replacement information. It also identifies the principal design trade-offs among CMOS and TTL counter options so engineers can select a replacement without changing the 16-pin through-hole footprint.

Alternativas drop-in para CD40160BE — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

HCF40160BEY

✅ Drop-In
📦 PDIP-16
Same 16-pin PDIP decade-counter footprint and function; supply, timing, output-drive, and temperature limits require comparison

📋 Alternativa de referência (fora do catálogo)

CD40160BE

✅ Drop-In
Texas Instruments
📦 PDIP-16
CMOS synchronous programmable 4-bit decade counter · 4-bit binary-coded decimal decade output · 0 to 9 · Synchronous · Asynchronous clear · 3 V to 18 V · 16 terminals · Through-hole

Consulte o preço

Ver ficha técnica →

CD40160BE Classificações máximas e características elétricas

Logic Type CMOS synchronous programmable 4-bit decade counter
Counter Output 4-bit binary-coded decimal decade output
Count Sequence 0 to 9
Clocking Synchronous
Clear Function Asynchronous clear
Supply Voltage Range 3 V to 18 V
Number of Terminals 16 terminals
Terminal Form Through-hole
Package Code DIP
Package Shape Rectangular
Temperature Grade Military
Logic Family CD4000 CMOS series
TTL Compatibility Functionally equivalent and pin-compatible with 74LS160

Guia de Configuração de Pinos do CD40160BE rectangular

Configuração de pinos para CD40160BE (pacote rectangular). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.

Diagrama de pinagem do pacote rectangular para CD40160BE

Nenhum dado detalhado de pinagem disponível para CD40160BE.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

CD40160BE é adequado para 6 aplicaçãos: Digital Clock and Timer, Industrial Pulse Counter, Laboratory Frequency Divider, Legacy TTL Equipment Upgrade, Programmable Sequential Control, Test and Measurement Counter.

📺

Digital Clock and Timer

The CD40160BE suits clock and timer designs that need a true decimal count rather than a free-running binary sequence. Each clock edge advances the four outputs through the BCD states 0 to 9, allowing the value to be decoded directly for decimal display or timekeeping. The load input can establish an initial count, the count-enable inputs can pause progression, and the asynchronous clear can reset the state without waiting for a clock edge. Because the part is a CMOS synchronous counter with a 3 V to 18 V supply range, it supports both traditional 5 V logic and lower-voltage control systems. Use the manufacturer pin-description table to connect the active clock, control inputs, and parallel outputs, and place supply bypassing close to the device.

🏭

Industrial Pulse Counter

The CD40160BE can count filtered sensor or machine pulses while presenting a decimal state to control and monitoring circuitry. Its 4-bit synchronous decade output is appropriate when each count increment represents one complete unit of ten rather than an arbitrary binary total. The enable inputs allow the count to advance only during a defined measurement interval, and the load function permits a repeatable starting value for each batch or production cycle. Asynchronous clear provides an immediate reset after an event or fault. In an industrial environment, route clock and control traces away from motor and switching-node edges, use a Schmitt trigger when the source signal has slow transitions, and verify operating temperature and supply limits against the military-grade ordering option.

🧩

Laboratory Frequency Divider

The CD40160BE provides predictable decade stages for laboratory counters, dividers, and repetitive sequencing fixtures. Dividing a stable clock by ten is useful when a panel instrument, recorder, or timing reference requires a lower-rate decimal pulse. Because counting is synchronous, the device avoids the cumulative propagation uncertainty associated with a chain of asynchronous ripple stages. The external controls also support engineering modes such as loading a preset state, holding the count, or clearing it between measurements. Keep the input clock edge clean and respect the manufacturer’s specified clock pulse-width limits. For long acquisition sequences, initialize the counter through the load or clear controls in a defined order so downstream logic does not observe an unintended intermediate count.

🔧

Legacy TTL Equipment Upgrade

The CD40160BE is a practical upgrade candidate for legacy equipment built around the 74LS160 because Texas Instruments documents the CD40160B as functionally equivalent and pin-compatible with the TTL counter family. Designers can preserve the existing 16-pin through-hole layout while moving the counter toward CMOS technology and its 3 V to 18 V operating range. This is especially useful when replacing older TTL logic with a mixed-voltage design or reducing system power. The substitution is not automatic: check clock-edge behavior, input thresholds, output levels, reset timing, and supply requirements on every connected net. Where the original board combines TTL outputs with CMOS inputs, confirm that the voltage levels and noise margins remain valid in the revised power architecture.

🤖

Programmable Sequential Control

The CD40160BE can form the decimal sequencing element of a programmable control system in which external logic determines when counting starts, stops, reloads, or resets. Its 4-bit parallel outputs make the decade state available for decoding into ten mutually exclusive control signals. The asynchronous clear allows a safety or supervisory circuit to reset the sequence immediately, while the load input supports repeatable presets. This arrangement is useful in relay sequencing, batch controls, teaching panels, and test fixtures where a decimal progression is more natural than binary counting. Define a deterministic priority for clear, load, enable, and clock inputs, and avoid placing asynchronous clear close to high-current switching edges. Confirm all decoded outputs during reset and loading before allowing them to control external equipment.

🖥️

Test and Measurement Counter

The CD40160BE is useful in test fixtures that need a compact decade-counting stage alongside legacy CMOS or TTL instrumentation. A measured input can be clocked into the counter, while load and enable controls establish the start condition and acquisition window. The four parallel outputs can then feed a display decoder, comparator, status indicator, or data-capture interface. The wide CMOS supply range supports integration into equipment operating from legacy 5 V rails, while the 16-pin PDIP package simplifies replacement on older through-hole boards. Keep the measured signal conditioned so its transitions meet the datasheet input requirements, and account for propagation delay when synchronizing the count with an external trigger. Decouple the supply locally and use consistent grounding between the counter and downstream logic to minimize noise-induced count errors.

Resumo dos produtos recomendados

CD40160BE Texas Instruments Usado em: Digital Clock and Timer, Industrial Pulse Counter, Laboratory Frequency Divider, Legacy TTL Equipment Upgrade, Programmable Sequential Control, Test and Measurement Counter 74LS160 Pin-compatible TTL decade-counter reference Usado em: Digital Clock and Timer, Industrial Pulse Counter, Laboratory Frequency Divider, Legacy TTL Equipment Upgrade, Test and Measurement Counter CD40161B Related synchronous binary-counter family Usado em: Programmable Sequential Control
What is the operating voltage of CD40160BE?
The CD40160BE operates from 3 V to 18 V, allowing it to support both legacy 5 V CMOS systems and lower-voltage counter designs. According to the Texas Instruments CD40160B family documentation, the device is a CMOS synchronous programmable 4-bit decade counter with asynchronous clear. Confirm that every connected signal remains within the input thresholds for the selected supply voltage before using the counter with 3.3 V or 5 V logic.
What does CD40160BE do?
The CD40160BE is a CMOS synchronous programmable 4-bit decade counter that advances through the ten states from 0 through 9 and presents the current count on four parallel outputs. Texas Instruments describes the CD40160B family as a synchronous programmable 4-bit decade counter with asynchronous clear. Its synchronous counting architecture provides defined output transitions on the clock edge, while load and enable controls support holding, starting, or clearing the count.
Where can I download the CD40160BE datasheet PDF?
The official CD40160BE technical information is available through the Texas Instruments CD40160B product page at https://www.ti.com/product/CD40160B. The page provides the manufacturer data sheet, ordering information, parameters, and package documentation for the CD40160B family. The CD40160BE is the 16-pin military-temperature PDIP ordering option within that family.
Where can I find the CD40160BE pinout?
The CD40160BE pin assignment is published in the Texas Instruments CD40160B manufacturer datasheet, linked from the official product page at https://www.ti.com/product/CD40160B. The device uses a 16-pin PDIP through-hole footprint with counter-clockwise numbering when the pin-1 end is identified. Use the manufacturer pin-description table when assigning clock, load, enable, clear, output, and supply connections.
What is the difference between CD40160BE and 74LS160?
The CD40160BE is a CD4000-series CMOS decade counter, while the 74LS160 is a Low-Power Schottky TTL decade counter. According to the Texas Instruments CD40160B family documentation, the CD40160B is functionally equivalent to and pin-compatible with the 74LS160. The meaningful design distinction is the logic technology and its associated voltage, speed, power, and environmental characteristics rather than a change in counter function.
When should I choose CD40160BE over a 74LS160 counter?
Choose the CD40160BE when the design benefits from CMOS operation, a 3 V to 18 V supply range, and the lower static power characteristics normally associated with CMOS logic. Choose a 74LS160 when an existing TTL-based circuit requires standard TTL signal compatibility and its specified operating conditions are preferable. Both provide the same decade-counting function and are identified by the CD40160B documentation as pin-compatible, allowing a technology-based upgrade on a compatible board.
What is the best drop-in replacement for CD40160BE?
The HCF40160BEY from STMicroelectronics is a documented cross-brand candidate for the CD40160BE because both are 16-pin PDIP, single 4-bit decade counters with synchronous counting. Before treating it as a drop-in replacement, compare supply voltage, clock timing, output levels, temperature grade, and asynchronous-clear behavior against the manufacturer datasheets. Renesas also markets a CD40160BE catalog entry, but its exact ordering and package conditions should be confirmed before substitution.
Can HCF40160BEY replace CD40160BE?
The HCF40160BEY can serve as a candidate replacement for the CD40160BE because cross-reference results identify both as 16-pin PDIP, single 4-bit synchronous decade counters. Pin compatibility alone does not guarantee identical electrical behavior. Confirm operating voltage, input thresholds, output drive, clock-edge requirements, clear polarity, and temperature limits in the respective Texas Instruments and STMicroelectronics datasheets before production use.
What can replace CD40160BE?
A valid replacement for the CD40160BE should preserve its 16-pin PDIP footprint, synchronous decade-counting behavior, parallel BCD outputs, load and count-enable functions, and asynchronous clear. The HCF40160BEY from STMicroelectronics is the clearest cross-brand candidate identified for a like-for-like comparison. Treat it as a qualified engineering option only after checking voltage, timing, output-level, and temperature specifications against the original design requirements.
Is the CD40160BE the same as the HCF40160BEY?
The CD40160BE and HCF40160BEY perform the same core function as 4-bit synchronous decade counters in 16-pin PDIP packages, but they are not necessarily identical in every electrical parameter. The CD40160BE belongs to the CD4000 CMOS family, while the HCF40160BEY is an STMicroelectronics HCF-series device. Check supply range, clock frequency, propagation delay, output current, and temperature grade before substitution.
Where can I buy CD40160BE online?
Use the Request a Quote form on this page to request CD40160BE availability, current lead time, and an order quote from XAIPART. The manufacturer lists the CD40160B family, and catalog information identifies CD40160BE as a 16-pin military-temperature PDIP counter. Because availability and commercial terms can change, submit the exact MPN and required quantity through the quote form rather than relying on a historical listing.
What is the price of CD40160BE?
Request the current CD40160BE unit and volume pricing through the Request a Quote form on this page. The structured commercial fields for this part contain the latest listing reference used by XAIPART, while the final transaction price depends on quantity, supply status, and order terms. No static price is stated in this answer because quotations can change with market and inventory conditions.
What is the lead time for CD40160BE?
Request the current CD40160BE lead time through the Request a Quote form on this page, including the required quantity, target date, and approved manufacturer or brand preference. The part is cataloged as a 16-pin PDIP military-temperature CD40160B option, but production and inventory status must be confirmed for the exact suffix. Quote requests provide the appropriate channel for a current lead-time commitment.
Is CD40160BE in stock?
Use the Request a Quote form on this page to request current CD40160BE inventory, because stock changes independently of the product record and may vary by quantity and package. The exact MPN is CD40160BE, a 16-pin PDIP version of the CD40160B decade counter. Providing the required order quantity allows XAIPART to check the current supply channel and return an availability and lead-time response.
What are the key specifications of CD40160BE that engineers should know?
The CD40160BE is a 3 V to 18 V CMOS, synchronous, programmable 4-bit decade counter with asynchronous clear, supplied in a 16-pin military-temperature PDIP package. It counts from 0 through 9 and provides four parallel decade outputs. The Texas Instruments family documentation also states that CD40160B is functionally equivalent to and pin-compatible with the 74LS160 counter, which is important when evaluating legacy TTL board upgrades.

Dados de referência de engenharia para CD40160BE — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the Texas Instruments CD40160BE when the design needs a synchronous BCD decade counter in a 16-pin military-temperature PDIP package, especially in legacy equipment where the documented 74LS160 pin compatibility simplifies PCB reuse. It is particularly appropriate for 3 V to 18 V CMOS systems requiring deterministic parallel counting and direct decade-decoder interfacing. The HCF40160BEY is the leading cross-brand candidate when a second-source CMOS counter is required, provided supply range, clock timing, output drive, and temperature limits pass comparison. The Renesas CD40160BE offering may provide procurement flexibility, but its exact package, qualification status, and electrical limits should be confirmed. None of these choices should be treated as an automatic substitution until the complete pin and timing tables have been reviewed.

Comparação com alternativas

Parâmetro Este produto HCF40160BEY CD40160BE
Brand Texas Instruments STMicroelectronics Renesas Electronics
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP
Counter Type Single 4-bit synchronous decade counter Single 4-bit synchronous decade counter 4-bit synchronous decade counter
Logic Technology CMOS CMOS CMOS
Asynchronous Clear Yes Yes Yes

Principais diferenciais

  • Provides a military-temperature ordering option in a serviceable through-hole package (vs HCF40160BEY)
  • Maintains a documented relationship with the widely used 74LS160 counter (vs HCF40160BEY)
  • Uses a broad CMOS supply range for legacy and lower-voltage systems (vs CD40160BE)

Notas de projeto

Treat the clock as the critical timing net because every counter state advances synchronously on its active edge. Route it away from inductive switching nodes and relay contacts, use a ground reference that remains stable through the measurement interval, and condition noisy sensor signals before they reach the clock input. If the source can cross the input threshold slowly, insert a suitable Schmitt-trigger stage rather than allowing a long transition region to generate an uncertain clock event.

Define the control priority used by the external logic before connecting asynchronous clear, load, and count-enable inputs. Resetting while loading or counting can otherwise produce a transition that differs from the assumed operating sequence. Also verify the required clock edge and pulse width in the manufacturer datasheet, particularly when a mechanical switch, relay contact, or RC-filtered oscillator drives the counter.

Place the supply-decoupling capacitor close to the device supply and ground pins, and keep the clock and control traces short on the 16-pin PDIP footprint. The through-hole package is convenient for serviceable legacy equipment, but it does not eliminate the need for controlled layout. Keep switching-regulator nodes and high-current return paths away from the clock trace, and use a consistent ground strategy between the counter and connected display or control circuitry.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The military temperature grade identifies environmental robustness, not AEC-Q100 qualification. Compliance declarations were not established by the cited product records.

Buscas relacionadas

CD40160BE datasheet CD40160BE pinout CD40160BE datasheet pdf Texas Instruments CD40160BE CD40160BE 16 pin PDIP CD40160BE equivalent CD40160BE replacement CD40160BE vs HCF40160BEY CD40160BE synchronous decade counter CD40160BE 3V 18V CD40160BE price CD40160BE stock CD40160BE application circuit CD40160BE vs 74LS160

Componentes & termos relacionados

Texas Instruments CD40160BE CD40160B HCF40160BEY STMicroelectronics Renesas Electronics 74LS160 CD4000 CMOS logic series synchronous counter programmable decade counter 4-bit counter binary-coded decimal CMOS logic IC digital logic IC asynchronous clear parallel counter output PDIP-16 DIP through-hole logic counter digital clock industrial pulse counting legacy TTL upgrade power supply decoupling clock signal integrity
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ