AVISO DE ÚLTIMA COMPRA: CD4053BMT está se aproximando do fim de vida. Data limite para pedidos: Fale conosco. Ver peças alternativas disponíveis →
Texas Instruments

CD4053BMT - 3-Channel 20V Analog Multiplexer | Texas Instruments

N.º da peça: CD4053BMT ⚠ Última compra
3 V to 20 V Vdss 100 nA Id 240 ohm Rds(on) 16-pin SOIC Package
MOQ: 1 |

CD4053BMT Visão geral

The Texas Instruments CD4053BMT is a three-channel, 2:1 analog multiplexer and demultiplexer rated for 20 V operation, with an on-state resistance of 240 ohms and a bandwidth of 30 MHz. The device is packaged in a 16-pin SOIC and includes logic-level conversion, allowing control signals to be referenced to different supply voltages from the switched analog signal. It also provides break-before-make switching behavior for applications requiring isolated signal paths during transitions.

An analog multiplexer is a semiconductor switch that connects one common terminal to any one of several channel terminals. A demultiplexer uses the same internal switching structure in the opposite direction, routing a common signal toward a selected output. The CD4053B family provides three independent SPDT paths, placing it in the interface IC and analog-switch hierarchies used for signal routing, instrumentation, communications, test equipment, and data acquisition.

The principal features of the CD4053BMT include three independently selectable 2:1 paths, a 240-ohm on-state resistance, and a 30 MHz bandwidth. Its logic-level conversion feature supports control from a supply different from the analog signal supply. Break-before-make operation prevents the common terminal from connecting momentarily to two switched terminals, an important property when the source may present conflicting voltages or when back-to-back switching would create an undesirable transient.

Internally, the CD4053B uses CMOS switching elements controlled by address and enable logic. The three channels can route a single source to one of two destinations or distribute one of two sources to a shared output. The 20 V operating capability permits use with higher-voltage analog signals than conventional 5 V or 3.3 V logic-oriented multiplexers, while the 30 MHz bandwidth is useful for moderate-frequency signal paths. Designers must still account for charge injection, off-state leakage, switching transients, and the dynamic behavior of the selected control sequence.

Typical applications include data-acquisition front ends, oscilloscope and laboratory signal routing, communications-channel selection, automated test equipment, audio and low-frequency control paths, and industrial systems that switch several analog signals through one shared interface. The triple-SPDT organization is particularly useful when a system must reverse signal direction between source and destination without changing the surrounding PCB footprint.

The primary design consideration is ensuring that address and enable transitions cannot momentarily connect conflicting analog sources. Preserve the device's break-before-make behavior, place bypass and signal-conditioning components close to the relevant pins, and use a control sequence that avoids changing an address while the common terminal carries a signal that cannot tolerate a brief disturbance. Verify voltage levels against the logic-level conversion thresholds before using the device with mixed-voltage systems.

This product page combines the manufacturer's 20 V, three-channel, 240-ohm and 30 MHz device characteristics with packaging guidance, application fit, and a structured comparison of same-footprint alternatives. It is intended to help engineers evaluate signal integrity, logic compatibility, lifecycle constraints, and replacement decisions before committing a board layout to this multiplexing function.

Alternativas drop-in para CD4053BMT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com CD4053BMT (mesmo formato e footprint) — diferindo em Package, Logic-Level Conversion, Mounting Type, Number of Channels, Product Type.

Texas Instruments
Package: 16-pin PDIP
Mounting Type: Through-hole
Product Type: Triple 2:1 SPDT analog multiplexer/demultiplexer with logic-level conversion
Comparar com CD4053BMT →
Texas Instruments
Package: 16-SOIC
Logic-Level Conversion: Yes
Number of Channels: 3
Comparar com CD4053BMT →

CD4053BE

✅ Drop-In ⚠️ Especificações não verificadas
Texas Instruments
📦 16-pin SOIC
Triple 2:1 SPDT analog multiplexer/demultiplexer with logic-level conversion · 3 circuits · 2:1 SPDT per channel · 20 V · 240 ohm · Supported · -55 °C to +125 °C · 16-pin PDIP

Consulte o preço

Ver ficha técnica →

CD4053BM

✅ Drop-In ⚠️ Especificações não verificadas
Texas Instruments
📦 16-pin SOIC
3-channel 2:1 SPDT analog multiplexer and demultiplexer · 20 V · 3 · 2:1 SPDT per channel · 240 ohm · Yes · A, B, and C · Common inhibit input

Consulte o preço

Ver ficha técnica →

CD4053BMP

✅ Drop-In ⚠️ Especificações não verificadas
📦 16-pin SOIC
Retains the three-channel, 20 V, 240-ohm and 30 MHz nominal ratings, a 0% difference in those stated values; ordering and temperature-grade characteristics require confirmation.

📋 Alternativa de referência (fora do catálogo)

SN74LV4053A

✅ Drop-In
📦 16-pin SOIC
Preserves the triple 2:1 function and 16-pin SOIC footprint; supply voltage and logic-threshold characteristics differ from the CD4000B family, with 0% difference in channel count.

📋 Alternativa de referência (fora do catálogo)

CD74HC4053

✅ Drop-In
📦 16-pin SOIC
Preserves the triple 2:1 function and 16-pin SOIC footprint; HC-series supply and input thresholds differ from CD4053BMT, with 0% difference in channel count.

📋 Alternativa de referência (fora do catálogo)

CD4053BMT Especificações

Multiplexer Configuration 3 x SPDT (2:1)
Number of Channels 3 channels
Supply Voltage Range 3 V to 20 V
On-State Resistance 240 ohm
Signal Bandwidth 30 MHz
Off-State Leakage Current 100 nA
Switching Behavior Break-before-make
Logic-Level Conversion Supported
Multiplexer Function Multiplexer and demultiplexer
Encapsulamento 16-pin SOIC
Tipo de montagem Surface mount
Technology CMOS
Maximum Input Voltage 20 V

Guia de Configuração de Pinos do CD4053BMT 16-pin soic

Configuração de pinos para CD4053BMT (pacote 16-pin soic). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 16-pin soic para CD4053BMT

Nenhum dado detalhado de pinagem disponível para CD4053BMT.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

CD4053BMT é adequado para 6 aplicaçãos: Industrial Data Acquisition, Automated Test Equipment, Communications Signal Routing, Instrument Signal Selection, Audio and Control Signal Switching, Bidirectional Multiplexer Interface.

🏭

Industrial Data Acquisition

The CD4053BMT fits multichannel industrial data-acquisition front ends that require several analog inputs to share a common converter or instrumentation path. Its three independent 2:1 SPDT channels provide 240-ohm on-state resistance and 30 MHz bandwidth, while the 20 V operating limit accommodates many process and test signals. Logic-level conversion allows address and enable controls to use a supply different from the switched signal rail. Use the break-before-make behavior deliberately so a common terminal is not briefly connected to conflicting sources during channel changes, and verify settling time and charge injection against the acquisition accuracy requirement.

🖥️

Automated Test Equipment

The CD4053BMT is suitable for automated test equipment that routes one instrument channel among multiple DUT or fixture nodes. Three independent 2:1 paths reduce the number of separate switching stages required for small multi-channel systems. The 240-ohm on-state resistance and 30 MHz bandwidth support moderate-bandwidth routing, while the 20 V limit covers many low-voltage test signals. For relay-like fixture isolation or precise settling, add suitable buffers or higher-bandwidth switches and validate the control timing so break-before-make transitions do not create unintended test-signal interruptions.

🌐

Communications Signal Routing

The CD4053BMT can route communication and control signals through a compact triple-SPDT matrix in communications equipment, interface modules, and signal-conditioning panels. Its three selectable paths support one-to-two routing or two-to-one demultiplexing, and the 30 MHz bandwidth is useful for moderate-speed digital or analog control signals. The 240-ohm on-state resistance should be included in source and load impedance calculations, especially at logic thresholds. Keep routing traces short, provide a continuous ground reference, and place any termination close to the receiving device.

📺

Instrument Signal Selection

The CD4053BMT is well suited to instrument signal selection where one common measurement input must be connected to one of two sensors, sources, or calibration paths. Its three channels provide independent selection without requiring three separate packages, while logic-level conversion supports control systems operating at a different voltage from the analog signal. The 240-ohm resistance can create measurement errors with high-impedance sensors or low currents, so account for loading and consider buffering. Confirm leakage, isolation, and settling behavior for precision measurements before finalizing the front end.

🎧

Audio and Control Signal Switching

The CD4053BMT can select audio, sensor, or control signals in compact analog interface blocks when the required bandwidth remains below 30 MHz. The triple-SPDT organization is useful for routing a common signal among sources or sending one of two sources to a shared output. Break-before-make behavior helps avoid direct contention during source changes. However, the nominal 240-ohm on-state resistance may attenuate high-impedance audio paths, and switching transients can be audible in sensitive systems. Use low-noise buffers when necessary and validate the complete signal chain with the intended source impedance.

🔧

Bidirectional Multiplexer Interface

The CD4053BMT supports bidirectional multiplexing when each SPDT common terminal is connected to the path that must switch direction, making the device useful in test, communications, and embedded interface circuits. Its three channels can independently reverse signal direction while preserving a fixed 16-pin SOIC footprint. The 20 V operating limit and logic-level conversion provide flexibility when analog and control domains use different voltage ranges. Validate the exact address mapping, enable polarity, and pinout in the manufacturer datasheet because a footprint-compatible part can still differ in control timing or logic thresholds.

Resumo dos produtos recomendados

CD4053BE Texas Instruments Usado em: Industrial Data Acquisition, Instrument Signal Selection, Bidirectional Multiplexer Interface CD74HC4053 Logic-compatible function to evaluate Usado em: Industrial Data Acquisition, Communications Signal Routing, Bidirectional Multiplexer Interface CD4053BM Texas Instruments Usado em: Automated Test Equipment, Instrument Signal Selection SN74LV4053A Triple SPDT switching alternative Usado em: Automated Test Equipment, Audio and Control Signal Switching CD4053BMP Same-family 16-pin SOIC alternative Usado em: Communications Signal Routing, Audio and Control Signal Switching
What is the operating voltage of CD4053BMT?
The CD4053BMT supports a maximum operating voltage of 20 V. According to the Texas Instruments CD4053B product page, it is a CMOS analog multiplexer with logic-level conversion, allowing its address and enable controls to operate from a supply different from the switched analog signal. The exact minimum operating voltage and the control-logic input thresholds should be confirmed in the manufacturer datasheet for the selected operating condition.
How many channels does CD4053BMT have?
The CD4053BMT contains three independent 2:1 SPDT switching channels. Texas Instruments describes the CD4053B as a three-channel, 20 V analog multiplexer and demultiplexer with logic-level conversion. Each channel can route its common terminal to either of two signal terminals, allowing the device to perform both multiplexing and demultiplexing functions depending on how the external circuit is connected.
What is the on-state resistance of CD4053BMT?
The nominal on-state resistance of the CD4053BMT is 240 ohms. According to the Texas Instruments CD4053B product documentation, the device combines this resistance with a 30 MHz signal bandwidth. The resistance figure should be treated as a nominal routing parameter rather than a series resistance that is independent of signal level; the manufacturer datasheet defines its test conditions and voltage dependence.
What is the bandwidth of CD4053BMT?
The CD4053BMT supports a signal bandwidth of 30 MHz. Texas Instruments lists a 30 MHz bandwidth for the CD4053B, together with 240-ohm on-state resistance and three SPDT channels. Bandwidth performance in a finished design also depends on source and load impedance, wiring length, capacitance, control timing, and the measurement method used for the switch.
Where can I download the CD4053BMT datasheet PDF?
The official CD4053BMT documentation is available from the Texas Instruments CD4053B product page at https://www.ti.com/product/CD4053B. The page identifies the device as a 20 V, three-channel 2:1 analog multiplexer with logic-level conversion and links to its technical documentation. Use the manufacturer's ordering and pin information when defining PCB footprints and control-signal assignments.
Where can I find the CD4053BMT pinout?
The CD4053BMT pinout should be taken from the pin-description table in the Texas Instruments CD4053B datasheet. It is a 16-pin SOIC device with three common analog paths, six channel terminals, address inputs, and an enable input in its functional organization. Because the package drawing alone does not identify safe signal assignments, verify every pin against the manufacturer datasheet before laying out the PCB.
What can replace CD4053BMT?
The CD4053BMT can only be replaced safely by a device with the same 16-pin SOIC footprint, matching three-channel 2:1 signal topology and compatible voltage and logic thresholds. Texas Instruments identifies SN74LV4053A and CD74HC4053 in its replacement discussion, but their logic families have different electrical characteristics. Verify pinout, control levels, on-resistance, bandwidth, off leakage, and lifecycle status before treating either device as a drop-in replacement.
Is SN74LV4053A the same as CD4053BMT?
SN74LV4053A is not electrically identical to CD4053BMT. Both provide a triple 2:1 switching function in a 16-pin SOIC package, but the LV logic family uses different supply and control-level characteristics from the CD4000B CMOS family. The useful comparison points are the 20 V-class signal capability, on-resistance, bandwidth, enable behavior, address mapping, and exact pin assignments in the manufacturer datasheets.
What is the best Texas Instruments equivalent for CD4053BMT?
CD4053BMT is already the temperature-grade ordering option of Texas Instruments' CD4053B family, so the closest functional alternatives are other CD4053B orderings and logic-family counterparts identified in the manufacturer's replacement discussion. Select an equivalent based on package, temperature grade, supply range, logic thresholds, lifecycle, and exact pinout. An ordering with the same base circuit but a different package is not a drop-in replacement.
When should I choose CD4053BMT instead of CD74HC4053?
Choose CD4053BMT when the circuit benefits from the CD4000B family's higher-voltage analog-switching capability and its logic-level conversion function. Choose CD74HC4053 when its lower-voltage logic characteristics and supply range better match the control system. The decision must also account for the different logic families, so a shared 16-pin footprint alone does not establish drop-in equivalence.
Is CD4053BMT suitable for industrial data acquisition?
The CD4053BMT can fit industrial data-acquisition designs that switch analog signals below its 20 V operating limit. Its three independent SPDT channels, 240-ohm on-state resistance, 30 MHz bandwidth, and logic-level conversion support channel selection and bidirectional routing. Industrial qualification, operating-temperature limits, isolation, settling behavior, and transient performance must be checked against the actual measurement requirements.
What are the key specifications of CD4053BMT that engineers should know?
The key CD4053BMT specifications are three independent 2:1 SPDT channels, a 20 V operating limit, 240-ohm nominal on-state resistance, 30 MHz bandwidth, 100 nA off-state leakage, CMOS construction, break-before-make switching, logic-level conversion, and a 16-pin SOIC package. Texas Instruments publishes these characteristics on the CD4053B product page. Application designs should also verify timing, temperature limits, and isolation in the complete datasheet.
How do I design the control sequence for CD4053BMT?
Design the control sequence so the enable input is asserted only when the selected address will not cause an undesirable break-before-make interruption at the common terminal. Disable the channel before changing its address when the switched signal cannot tolerate a temporary open. Keep address and enable traces away from sensitive analog paths and use clean logic levels that satisfy the CD4053B control-input requirements.
Where to buy CD4053BMT online?
Use the Request a Quote form on this page to request CD4053BMT availability, current lead time, minimum order quantity, and the required package form. The manufacturer lists the base CD4053B family, while distributor records identify CD4053BMT as a 16-SOIC ordering with a last-time-buy status. Quote requests should state the quantity and whether tape-and-reel, cut-tape, or another packing form is required.
What is the price of CD4053BMT?
The current CD4053BMT price should be requested through the Request a Quote form on this page because availability and order quantities affect the commercial terms. The available price references do not provide qualifying quantity-break tables for this exact ordering, so no static unit price is asserted here. Include the target quantity, packaging preference, and required delivery date when submitting the request.
What is the lead time for CD4053BMT?
The current lead time for CD4053BMT should be confirmed through the Request a Quote form on this page. Texas Instruments identifies the CD4053B device family, and a distributor record describes CD4053BMT as a last-time-buy part. Because lifecycle and supply status can change, provide the required quantity and packaging details with the request rather than relying on a generic stock estimate.
Is CD4053BMT in stock?
Stock for CD4053BMT should be confirmed through the Request a Quote form on this page. The manufacturer continues to document the CD4053B family, while a distributor listing identifies CD4053BMT as a last-time-buy ordering and another listing describes it as in stock at the time of capture. Submit the required quantity and packaging form for a current allocation response.
What is the best cross-brand equivalent for CD4053BMT?
No cross-brand equivalent is established as a drop-in replacement for CD4053BMT in the available replacement records. A valid cross-brand candidate must use the same 16-pin SOIC footprint, implement three 2:1 channels, preserve the address and enable mapping, and meet the circuit's voltage, resistance, leakage, bandwidth, timing, and temperature requirements. Validate any proposed part against both datasheets rather than relying only on its multiplex or demultiplex function.

Dados de referência de engenharia para CD4053BMT — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose CD4053BMT when the design needs three independent SPDT paths in a 16-pin SOIC, signals up to the 20 V operating classification, and control logic that may operate at a different voltage from the switched analog domain. Its 240-ohm on-state resistance and 30 MHz bandwidth are suitable for moderate-speed routing, but impedance and leakage checks remain necessary.

Choose SN74LV4053A when the control system is designed around the LV logic family and its supply and threshold characteristics are preferable, after confirming the pin mapping and electrical limits. Choose CD74HC4053 when an HC-series interface is preferred for its logic ecosystem, subject to the same voltage and timing verification. Same-family CD4053B orderings can be considered when procurement requirements differ, but their temperature grade, lifecycle, and orderable configuration must be confirmed. No cross-brand part is recommended as a drop-in substitute without a formal pin-, voltage-, timing-, and signal-integrity comparison.

Comparação com alternativas

Parâmetro Este produto CD4053BE CD4053BM CD4053BMP SN74LV4053A CD74HC4053
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Multiplexer Configuration 3 x SPDT (2:1) 3 x SPDT (2:1) 3 x SPDT (2:1) 3 x SPDT (2:1) 3 x SPDT (2:1) 3 x SPDT (2:1)
Number of Channels 3 channels 3 channels 3 channels 3 channels 3 channels 3 channels

Principais diferenciais

  • Higher-voltage analog switching with logic-level conversion (vs CD74HC4053)
  • Triple-SPDT routing in a standard 16-pin SOIC (vs SN74LV4053A)
  • Established 240-ohm and 30 MHz routing characteristics (vs CD4053BE)

Notas de projeto

Do not assume that a matching 16-pin SOIC footprint guarantees drop-in operation. The CD4053B, SN74LV4053A, and CD74HC4053 families use different logic levels and supply characteristics. Compare address mapping, enable polarity, input thresholds, supply range, on-resistance, leakage, bandwidth, and pin names in the manufacturer datasheets. For a last-time-buy design, qualify the chosen replacement before committing new production volumes.

Place the CD4053BMT close to the source and destination terminals it routes, and keep the common and switched analog paths short. Connect the supply and ground pins with short, low-impedance traces and place the required bypass capacitor at the device. Route address and enable signals away from sensitive analog nets. Preserve a continuous ground reference across every switch path because switched-source impedance, lead capacitance, and control coupling can affect settling and channel isolation.

Include the nominal 240-ohm on-state resistance in the source and load calculation, especially when driving a high-impedance sensor or small-signal amplifier. The 30 MHz bandwidth is a device characteristic, not a guaranteed system bandwidth; external capacitance, source impedance, and the selected channel can reduce practical performance. Use buffers when the source cannot drive the switch resistance, and validate settling and crosstalk with the actual signal path.

Use the 20 V operating limit as an absolute design boundary rather than a target rail. Confirm control-signal levels, switched-signal amplitudes, and supply tolerances against the manufacturer datasheet before energizing the device. Because the CD4053B supports logic-level conversion, the control supply and analog-signal supply may differ; nevertheless, every externally driven terminal must remain within its specified voltage and absolute-maximum limits.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The CD4053BMT is described by Texas Instruments as a 20 V, three-channel analog multiplexer and demultiplexer with logic-level conversion. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the product records, so these fields remain unknown.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

CD4053BMT datasheet CD4053BMT pinout CD4053BMT datasheet pdf CD4053BMT equivalent CD4053BMT replacement CD4053BMT cross reference CD4053BMT vs SN74LV4053A CD4053BMT vs CD74HC4053 CD4053BMT price CD4053BMT stock Texas Instruments CD4053BMT CD4053BMT 20V 240 ohm CD4053BMT SOIC-16 footprint CD4053BMT data acquisition

Componentes & termos relacionados

Texas Instruments CD4053BMT CD4053B CD4053BE CD4053BM CD4053BMP SN74LV4053A CD74HC4053 analog multiplexer analog demultiplexer interface IC semiconductor SPDT switch 2:1 switch CMOS logic-level conversion break-before-make on-state resistance signal bandwidth off-state leakage current 16-pin SOIC SOIC family surface-mount technology industrial data acquisition automated test equipment
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ