CD4053BMT - 3-Channel 20V Analog Multiplexer | Texas Instruments
MPN: CD4053BMT ⚠ Son Satın AlmaCD4053BMT Genel Bakış
An analog multiplexer is a semiconductor switch that connects one common terminal to any one of several channel terminals. A demultiplexer uses the same internal switching structure in the opposite direction, routing a common signal toward a selected output. The CD4053B family provides three independent SPDT paths, placing it in the interface IC and analog-switch hierarchies used for signal routing, instrumentation, communications, test equipment, and data acquisition.
The principal features of the CD4053BMT include three independently selectable 2:1 paths, a 240-ohm on-state resistance, and a 30 MHz bandwidth. Its logic-level conversion feature supports control from a supply different from the analog signal supply. Break-before-make operation prevents the common terminal from connecting momentarily to two switched terminals, an important property when the source may present conflicting voltages or when back-to-back switching would create an undesirable transient.
Internally, the CD4053B uses CMOS switching elements controlled by address and enable logic. The three channels can route a single source to one of two destinations or distribute one of two sources to a shared output. The 20 V operating capability permits use with higher-voltage analog signals than conventional 5 V or 3.3 V logic-oriented multiplexers, while the 30 MHz bandwidth is useful for moderate-frequency signal paths. Designers must still account for charge injection, off-state leakage, switching transients, and the dynamic behavior of the selected control sequence.
Typical applications include data-acquisition front ends, oscilloscope and laboratory signal routing, communications-channel selection, automated test equipment, audio and low-frequency control paths, and industrial systems that switch several analog signals through one shared interface. The triple-SPDT organization is particularly useful when a system must reverse signal direction between source and destination without changing the surrounding PCB footprint.
The primary design consideration is ensuring that address and enable transitions cannot momentarily connect conflicting analog sources. Preserve the device's break-before-make behavior, place bypass and signal-conditioning components close to the relevant pins, and use a control sequence that avoids changing an address while the common terminal carries a signal that cannot tolerate a brief disturbance. Verify voltage levels against the logic-level conversion thresholds before using the device with mixed-voltage systems.
This product page combines the manufacturer's 20 V, three-channel, 240-ohm and 30 MHz device characteristics with packaging guidance, application fit, and a structured comparison of same-footprint alternatives. It is intended to help engineers evaluate signal integrity, logic compatibility, lifecycle constraints, and replacement decisions before committing a board layout to this multiplexing function.
Drop-in alternatifler için CD4053BMT — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller CD4053BMT (aynı form faktörü ve ayağa oturma) — farklı olan Package, Logic-Level Conversion, Mounting Type, Number of Channels, Product Type.
CD4053BE
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →CD4053BM
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →CD4053BMP
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
SN74LV4053A
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
CD74HC4053
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
CD4053BMT Özellikler
| Multiplexer Configuration | 3 x SPDT (2:1) |
| Number of Channels | 3 channels |
| Supply Voltage Range | 3 V to 20 V |
| On-State Resistance | 240 ohm |
| Signal Bandwidth | 30 MHz |
| Off-State Leakage Current | 100 nA |
| Switching Behavior | Break-before-make |
| Logic-Level Conversion | Supported |
| Multiplexer Function | Multiplexer and demultiplexer |
| Paket | 16-pin SOIC |
| Montaj Türü | Surface mount |
| Technology | CMOS |
| Maximum Input Voltage | 20 V |
CD4053BMT 16-pin soic Pin Yapısı Kılavuzu
CD4053BMT (16-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: CD4053BMT.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
CD4053BMT için uygundur 6 uygulamas: Industrial Data Acquisition, Automated Test Equipment, Communications Signal Routing, Instrument Signal Selection, Audio and Control Signal Switching, Bidirectional Multiplexer Interface.
Industrial Data Acquisition
The CD4053BMT fits multichannel industrial data-acquisition front ends that require several analog inputs to share a common converter or instrumentation path. Its three independent 2:1 SPDT channels provide 240-ohm on-state resistance and 30 MHz bandwidth, while the 20 V operating limit accommodates many process and test signals. Logic-level conversion allows address and enable controls to use a supply different from the switched signal rail. Use the break-before-make behavior deliberately so a common terminal is not briefly connected to conflicting sources during channel changes, and verify settling time and charge injection against the acquisition accuracy requirement.
Önerilen
Automated Test Equipment
The CD4053BMT is suitable for automated test equipment that routes one instrument channel among multiple DUT or fixture nodes. Three independent 2:1 paths reduce the number of separate switching stages required for small multi-channel systems. The 240-ohm on-state resistance and 30 MHz bandwidth support moderate-bandwidth routing, while the 20 V limit covers many low-voltage test signals. For relay-like fixture isolation or precise settling, add suitable buffers or higher-bandwidth switches and validate the control timing so break-before-make transitions do not create unintended test-signal interruptions.
Önerilen
Communications Signal Routing
The CD4053BMT can route communication and control signals through a compact triple-SPDT matrix in communications equipment, interface modules, and signal-conditioning panels. Its three selectable paths support one-to-two routing or two-to-one demultiplexing, and the 30 MHz bandwidth is useful for moderate-speed digital or analog control signals. The 240-ohm on-state resistance should be included in source and load impedance calculations, especially at logic thresholds. Keep routing traces short, provide a continuous ground reference, and place any termination close to the receiving device.
Önerilen
Instrument Signal Selection
The CD4053BMT is well suited to instrument signal selection where one common measurement input must be connected to one of two sensors, sources, or calibration paths. Its three channels provide independent selection without requiring three separate packages, while logic-level conversion supports control systems operating at a different voltage from the analog signal. The 240-ohm resistance can create measurement errors with high-impedance sensors or low currents, so account for loading and consider buffering. Confirm leakage, isolation, and settling behavior for precision measurements before finalizing the front end.
Önerilen
Audio and Control Signal Switching
The CD4053BMT can select audio, sensor, or control signals in compact analog interface blocks when the required bandwidth remains below 30 MHz. The triple-SPDT organization is useful for routing a common signal among sources or sending one of two sources to a shared output. Break-before-make behavior helps avoid direct contention during source changes. However, the nominal 240-ohm on-state resistance may attenuate high-impedance audio paths, and switching transients can be audible in sensitive systems. Use low-noise buffers when necessary and validate the complete signal chain with the intended source impedance.
Önerilen
Bidirectional Multiplexer Interface
The CD4053BMT supports bidirectional multiplexing when each SPDT common terminal is connected to the path that must switch direction, making the device useful in test, communications, and embedded interface circuits. Its three channels can independently reverse signal direction while preserving a fixed 16-pin SOIC footprint. The 20 V operating limit and logic-level conversion provide flexibility when analog and control domains use different voltage ranges. Validate the exact address mapping, enable polarity, and pinout in the manufacturer datasheet because a footprint-compatible part can still differ in control timing or logic thresholds.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: CD4053BMT — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Choose SN74LV4053A when the control system is designed around the LV logic family and its supply and threshold characteristics are preferable, after confirming the pin mapping and electrical limits. Choose CD74HC4053 when an HC-series interface is preferred for its logic ecosystem, subject to the same voltage and timing verification. Same-family CD4053B orderings can be considered when procurement requirements differ, but their temperature grade, lifecycle, and orderable configuration must be confirmed. No cross-brand part is recommended as a drop-in substitute without a formal pin-, voltage-, timing-, and signal-integrity comparison.
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | CD4053BE | CD4053BM | CD4053BMP | SN74LV4053A | CD74HC4053 |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Multiplexer Configuration | 3 x SPDT (2:1) | 3 x SPDT (2:1) | 3 x SPDT (2:1) | 3 x SPDT (2:1) | 3 x SPDT (2:1) | 3 x SPDT (2:1) |
| Number of Channels | 3 channels | 3 channels | 3 channels | 3 channels | 3 channels | 3 channels |
Ana Farklılayıcılar
- Higher-voltage analog switching with logic-level conversion (karşılaştırma:CD74HC4053)
- Triple-SPDT routing in a standard 16-pin SOIC (karşılaştırma:SN74LV4053A)
- Established 240-ohm and 30 MHz routing characteristics (karşılaştırma:CD4053BE)
Tasarım Notları
Do not assume that a matching 16-pin SOIC footprint guarantees drop-in operation. The CD4053B, SN74LV4053A, and CD74HC4053 families use different logic levels and supply characteristics. Compare address mapping, enable polarity, input thresholds, supply range, on-resistance, leakage, bandwidth, and pin names in the manufacturer datasheets. For a last-time-buy design, qualify the chosen replacement before committing new production volumes.
Place the CD4053BMT close to the source and destination terminals it routes, and keep the common and switched analog paths short. Connect the supply and ground pins with short, low-impedance traces and place the required bypass capacitor at the device. Route address and enable signals away from sensitive analog nets. Preserve a continuous ground reference across every switch path because switched-source impedance, lead capacitance, and control coupling can affect settling and channel isolation.
Include the nominal 240-ohm on-state resistance in the source and load calculation, especially when driving a high-impedance sensor or small-signal amplifier. The 30 MHz bandwidth is a device characteristic, not a guaranteed system bandwidth; external capacitance, source impedance, and the selected channel can reduce practical performance. Use buffers when the source cannot drive the switch resistance, and validate settling and crosstalk with the actual signal path.
Use the 20 V operating limit as an absolute design boundary rather than a target rail. Confirm control-signal levels, switched-signal amplitudes, and supply tolerances against the manufacturer datasheet before energizing the device. Because the CD4053B supports logic-level conversion, the control supply and analog-signal supply may differ; nevertheless, every externally driven terminal must remain within its specified voltage and absolute-maximum limits.
Uyumluluk Bilgisi
The CD4053BMT is described by Texas Instruments as a 20 V, three-channel analog multiplexer and demultiplexer with logic-level conversion. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the product records, so these fields remain unknown.