DG419CJ+ - 35Ω SPDT CMOS Analog Switch | Analog Devices
N.º da peça: DG419CJ+ ✓ AtivoDG419CJ+ Visão geral
An SPDT analog switch is a semiconductor device that connects one common terminal to one of two switched terminals. In the broader component hierarchy, the DG419CJ+ belongs to the analog switch, analog multiplexer, interface IC, and semiconductor categories. This topology allows a signal source to be routed to either destination, or alternately connects two external nodes, making it useful for test systems, measurement equipment, signal routing, and precision analog systems.
Key characteristics include matching between the two switch paths to within 3 Ω maximum and flatness across the signal range to within 4 Ω maximum. These parameters help minimize path-dependent gain error and distortion when the same signal is routed through either side of the switch. The monolithic CMOS construction supports equal signal conduction in either direction and provides a compact interface IC solution for bipolar and split-supply analog circuits.
The DG419CJ+ offers a practical 35 Ω maximum on-resistance for precision, rather than ultra-low-impedance, routing. Its 8-pin DIP package accepts a 0.300-inch, 7.62 mm body width and facilitates through-hole assembly, prototyping, and socket-based laboratory use. The switch operates with positive and negative analog supplies, allowing bipolar signals to pass without single-ended signal-path restrictions.
Typical uses include precision test and measurement systems, sample-and-hold front ends, signal-routing matrices, laboratory equipment, and industrial control modules. The matched paths are especially useful when calibration or measurement results must remain consistent regardless of which switched terminal is selected. It is also suitable for designs that route low-frequency analog signals rather than high-speed RF or ultrafast data lines.
Designers should evaluate the 35 Ω on-resistance against the source and load impedance. A high-impedance receiving circuit will reduce the impact of that resistance, while a low-impedance load may require an amplifier or a lower-resistance switch. Also verify control-pin levels, supply sequencing, and unused-pin handling against the Analog Devices DG419 data sheet before finalizing the layout.
This product page combines the manufacturer’s core electrical characteristics with application-specific design guidance, package information, comparison criteria, and practical selection guidance. It is intended to help engineers determine whether the DG419CJ+ offers the required switch topology, resistance behavior, supply range, and through-hole footprint before beginning a board design.
Alternativas drop-in para DG419CJ+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com DG419CJ+ (mesmo formato e footprint) — diferindo em Mounting Type, On-Resistance Flatness, On-Resistance Matching, Package, Switch Configuration.
DG419CJ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
DG419DJ+
✅ Drop-InConsulte o preço
Ver ficha técnica →DG419DJ+
✅ Drop-InConsulte o preço
Ver ficha técnica →DG419CJ+ Classificações máximas e características elétricas
| Switch Configuration | SPDT |
| Number of Channels | 1 channel |
| On-Resistance | 35 Ω maximum |
| On-Resistance Matching | 3 Ω maximum |
| On-Resistance Flatness | 4 Ω maximum |
| Technology | CMOS |
| High-Side Supply Voltage Range | 10 V to 30 V |
| Low-Side Supply Voltage Range | -30 V to -10 V |
| Alternate Supply Voltage Range | 4.5 V to 20 V |
| Alternate Low-Side Supply Voltage Range | -20 V to -4.5 V |
| Encapsulamento | 8-pin DIP |
| Package Body Width | 0.300 inch (7.62 mm) |
| Tipo de montagem | Through hole |
| Contagem de pinos | 8 pins |
| Signal Conduction Direction | Bidirectional |
| Status do ciclo de vida | Production |
Guia de Configuração de Pinos do DG419CJ+ 0.300 inch (7.62 mm)
Configuração de pinos para DG419CJ+ (pacote 0.300 inch (7.62 mm)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para DG419CJ+.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
DG419CJ+ é adequado para 6 aplicaçãos: Precision Test and Measurement Systems, Analog Signal Routing Matrices, Sample-and-Hold Front Ends, Laboratory Interface Equipment, Industrial Control Signal Selection, Programmable Low-Frequency Signal Paths.
Precision Test and Measurement Systems
The DG419CJ+ fits precision signal-routing and instrument-selection circuits where path-dependent error must remain predictable. Its 35 Ω maximum on-resistance is paired with matching of 3 Ω maximum between the two switched paths and flatness of 4 Ω maximum across the signal range. Place the common terminal at the signal source, connect the two destination terminals to the measured and reference channels, and drive the control input from the test controller. The matched paths help limit calibration differences when an instrument alternates between DUT, standard, and termination networks.
Recomendado
Analog Signal Routing Matrices
The DG419CJ+ is appropriate for small modular analog routing matrices that must select one of two signal paths with repeatable resistance behavior. Its 1-channel SPDT topology provides a simple way to connect a shared source to either of two destinations. The 3 Ω maximum matching specification helps prevent one selected path from changing the effective source impedance relative to the other path. For higher-impedance sensors and amplifiers, the 35 Ω maximum insertion resistance can often be accepted with little signal attenuation, provided the control timing and supply rails satisfy the application.
Recomendado
Sample-and-Hold Front Ends
The DG419CJ+ can implement a precision sampling-path selection function in laboratory and industrial measurement front ends. Its low and matched on-resistance characteristics reduce variation between the sampled signal and a reference or calibration path. The CMOS switch supports bipolar signals when operated with the appropriate positive and negative supplies, while the 8-pin DIP package simplifies through-hole prototyping and socketed laboratory assembly. Designers should verify the signal bandwidth, charge injection, and control-input timing against the acquisition requirements before using the switch directly at a high-impedance sampling node.
Recomendado
Laboratory Interface Equipment
The DG419CJ+ is well suited to bench instruments and interface modules that select between external and internal test signals. Its through-hole 8-pin DIP package permits straightforward PCB assembly, socket use, and replacement during instrument development. The 35 Ω maximum on-resistance introduces a manageable loss when driving a high-impedance instrument input, while 3 Ω maximum path matching supports repeatable channel selection. Use separate supply bypassing near the device and keep control traces away from sensitive analog terminals to reduce coupling into the switched signal.
Recomendado
Industrial Control Signal Selection
The DG419CJ+ can select one of two analog command or feedback paths in industrial control modules where precision and repeatability matter more than extremely low insertion resistance. The matched switched paths help maintain consistent behavior when a controller alternates between a sensor input and a reference level. The device accepts bipolar supplies in the ±4.5 V to ±20 V range, which supports systems using positive and negative analog rails. Its 35 Ω maximum on-resistance should be checked against the control input impedance, and the control logic must remain stable across the full supply range.
Recomendado
Programmable Low-Frequency Signal Paths
The DG419CJ+ supports programmable routing in educational, diagnostic, and low-frequency automated test equipment. One control signal determines whether the common node connects to the normally closed or normally open path, allowing software to select sources or loads without changing wiring. The 1-channel SPDT arrangement is simple to implement and inspect, and the 8-pin DIP package is convenient for prototyping. Because this is a precision analog switch rather than an ultrafast RF switch, designers should evaluate bandwidth and insertion-loss requirements before applying it to high-frequency signals.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para DG419CJ+ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | DG419CJ | DG419DJ+ | DG419DJ |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin DIP | 8-pin DIP - same | 8-pin DIP - same | 8-pin DIP - same |
| Switch Configuration | SPDT | SPDT | SPDT | SPDT |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| On-Resistance Matching | 3 Ω maximum | 3 Ω maximum | 3 Ω maximum | 3 Ω maximum |
| On-Resistance Flatness | 4 Ω maximum | 4 Ω maximum | 4 Ω maximum | 4 Ω maximum |
| Technology | CMOS | CMOS | CMOS | CMOS |
Principais diferenciais
- Matched switch paths reduce path-dependent measurement error (vs DG419CJ)
- Through-hole precision switching in the same 8-pin DIP family (vs DG419DY+)
- Precision SPDT function without changing the family architecture (vs DG419DJ+)
Notas de projeto
Evaluate the 35 Ω maximum on-resistance together with the source and load impedance. A resistive divider formed by the switch and a low-impedance load can attenuate the signal more than expected, while a high-impedance receiving amplifier will usually preserve the signal more effectively. For bidirectional operation, keep both switched terminals within the specified signal and supply ranges and observe the absolute voltage limits in the manufacturer Data Sheet.
Route the common, normally closed, and normally open analog terminals away from the digital control traces. Place the device close to the source and destination connections to minimize parasitic capacitance and resistance, particularly when the switched signal is dynamically measured. Add local supply bypassing between each supply pin and ground, using a short ground return to limit switching transients that could couple into adjacent analog signals.
Do not treat the similar DG419 ordering suffixes as automatically identical without checking the exact temperature grade, control thresholds, and supply conditions. Also confirm the polarity and sequencing of the positive and negative supplies before applying bipolar signals. Because the device switches equally well in either direction, incorrect terminal identification can connect an unintended source to the common node even when the control command appears correct.
Use a low-impedance ground reference and avoid placing sensitive analog traces beneath or immediately beside the control input. If a relay or other slow-changing signal controls the switch, add suitable control conditioning rather than relying on a floating logic input. Keep prototyping wiring short, because breadboard capacitance and resistance can obscure the low-level behavior that the precision DG419 family is intended to preserve.
Informações de conformidade
The exact compliance status is not stated for the DG419CJ+ ordering code. A comparison page labels RoHS details for the DG419 family but does not explicitly establish a compliant or non-compliant result. The switch is an interface IC rather than an automotive-qualified AEC-Q100 device.