Analog Devices

DG419LDJ+ - 35 Ohm SPDT Analog Switch | Analog Devices

N.º da peça: DG419LDJ+ ✓ Ativo
±4.5 V Vdss 5 nA at +85°C Id 35 ohm Rds(on) 8-pin PDIP Package
MOQ: 1 |

DG419LDJ+ Visão geral

The Analog Devices DG419LDJ+ is a single-channel SPDT CMOS analog switch with 35 ohm maximum on-resistance, +3 V logic compatibility, and an 8-pin PDIP package. It supports dual-supply operation from ±4.5 V to ±20 V and an extended operating temperature range of -40°C to +85°C. The switch is designed for low-voltage, low-power signal-routing applications where one source must connect to one of two destinations.

An analog switch is an interface IC that connects or isolates an analog signal under digital control. A SPDT switch can route one common terminal to either of two independent terminals, making it useful for signal selection, polarity routing, test-point isolation, and signal-path multiplexing. The DG419LDJ+ belongs to the Analog Devices DG419L precision analog-switch family, combining low on-resistance with improved matching, flat on-resistance, low charge injection, and low off-leakage.

Key features include a maximum on-resistance of 35 ohms, on-resistance matching within 3 ohms, and flat on-resistance variation limited to 4 ohms across the signal range. Charge injection is limited to 10 pC, while off-leakage remains below 5 nA at +85°C. The logic-compatible control architecture allows +3 V control operation when the device is powered from ±12 V or ±15 V supplies, simplifying interfacing with modern control logic.

The DG419LDJ+ uses a low-power CMOS analog-switch architecture to support signal routing without adding substantial dynamic power. Its improved matching between channels and guaranteed flat on-resistance make it appropriate where consistent insertion loss matters across the selected signal range. The 185 ns maximum off-time supports applications requiring rapid transition between routed states.

Typical uses include audio signal routing, battery-operated equipment, communication systems, guidance and control circuits, military radios, modems, and PBX or PABX equipment. The device is particularly useful where a ±4.5 V minimum dual supply is acceptable and a through-hole PDIP package simplifies inspection, prototyping, and serviceability.

Use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Keep the common and switched terminals away from long parallel routes carrying fast signals, connect supply decoupling close to the appropriate pins, and verify the control voltage against the selected supply configuration before powering the device.

This page consolidates manufacturer specifications, sourcing guidance, application fit, and practical design notes for engineers evaluating the DG419LDJ+. It also distinguishes true package-compatible alternatives from related surface-mount versions that require a different PCB footprint.

Alternativas drop-in para DG419LDJ+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

DG419LDJ

✅ Drop-In
📦 8-pin PDIP
Ordering suffix differs; the documented family rating of 35 ohm maximum on-resistance and ±4.5 V to ±20 V dual-supply range remains applicable

📋 Alternativa de referência (fora do catálogo)

DG419LDJ+ Classificações máximas e características elétricas

Configuration 1 x SPDT
Number of Channels 1 channel
Maximum On-Resistance 35 ohm
On-Resistance Matching 3 ohm maximum
Flat On-Resistance 4 ohm maximum
Maximum Charge Injection 10 pC
Maximum Off-Leakage Current 5 nA at +85°C
Maximum Off Time 185 ns
Minimum Dual-Supply Voltage ±4.5 V
Maximum Dual-Supply Voltage ±20 V
Logic Compatibility +3 V compatible at ±12 V or ±15 V supply
Minimum Operating Temperature -40°C
Maximum Operating Temperature +85°C
ESD withstand 2000 V minimum
Encapsulamento 8-pin PDIP
Tipo de montagem Through-hole

Guia de Configuração de Pinos do DG419LDJ+ 8-pin pdip

Configuração de pinos para DG419LDJ+ (pacote 8-pin pdip). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 8-pin pdip para DG419LDJ+

Nenhum dado detalhado de pinagem disponível para DG419LDJ+.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

DG419LDJ+ é adequado para 6 aplicaçãos: Audio Signal Routing, Battery-Operated Test Equipment, Communication Signal Multiplexing, Guidance and Control Systems, Military Radio Signal Routing, Precision Signal Isolation.

🎧

Audio Signal Routing

The DG419LDJ+ is suitable for selecting one of two low-level audio paths through its single SPDT channel. Its 35 ohm maximum on-resistance limits insertion loss in high-impedance audio routing, while the 4 ohm maximum flat-on-resistance variation helps maintain consistent channel behavior across the signal range. The +3 V-compatible control input also simplifies operation from modern digital control circuits when the switch is powered from ±12 V or ±15 V. For microphone preamplifier or line-level routing, confirm that 35 ohm is acceptable relative to the source impedance and that the selected supply configuration meets the audio board’s ground and common-mode requirements.

🔋

Battery-Operated Test Equipment

The DG419LDJ+ can route a measurement signal inside compact battery-operated systems when its dual-supply requirement can be met. The SPDT configuration allows a common input to select between two sources without duplicating the surrounding analog circuitry. Its low-power CMOS implementation and low 185 ns off-time support fast path changes, while off-leakage below 5 nA at +85°C helps isolate inactive paths. Because the minimum dual supply is ±4.5 V, designers using a single low-voltage battery should include an appropriate rail converter rather than assuming the device can operate from a single 3.3 V supply.

🌐

Communication Signal Multiplexing

The DG419LDJ+ can select between communication paths in modems, PBX, and PABX equipment where one channel is sufficient for the required routing topology. The maximum on-resistance of 35 ohm is especially suitable for high-impedance receive-side routing, and the specified 185 ns off-time permits rapid isolation between paths. The improved 3 ohm channel matching and 4 ohm flat-on-resistance limits support more uniform behavior than unmatched general-purpose switches. In higher-impedance or wider-band networks, evaluate capacitance, insertion loss, and signal-level limits across the complete operating frequency range before fixing the design.

🏭

Guidance and Control Systems

The DG419LDJ+ provides a compact SPDT routing element for guidance, control, and industrial instrumentation systems that need to connect one command or feedback signal to one of two destinations. Its -40°C to +85°C rating supports a broad range of industrial ambient conditions, and the PDIP package simplifies through-hole assembly in control hardware. The 35 ohm on-resistance is appropriate for many high-impedance sensor and control paths, but designers should verify the driven input impedance. The 10 pC charge-injection limit should also be considered when switching sampled control signals into precision acquisition circuitry.

✈️

Military Radio Signal Routing

The DG419LDJ+ can serve as a precision SPDT switch in military radio and ruggedized communication equipment where one RF-control or low-frequency signal path must be selected between two sources. The guaranteed 3 ohm on-resistance matching and 4 ohm flat-on-resistance variation help reduce channel-dependent behavior, while the 2000 V minimum ESD withstand rating provides an identifiable robustness specification. Through-hole packaging supports serviceable and mechanically rugged assemblies. Signal engineers should still verify bandwidth, insertion loss, isolation, and permissible signal amplitude for the intended radio frequency rather than relying on the DC on-resistance alone.

🔬

Precision Signal Isolation

The DG419LDJ+ is useful for isolating one of two low-level analog inputs while routing a common signal elsewhere. Its off-leakage below 5 nA at +85°C limits unwanted coupling from disconnected paths, and the low 10 pC maximum charge injection helps control switching transients in precision measurement systems. The extended temperature range of -40°C to +85°C supports industrial environments. For high-accuracy front ends, verify leakage over the actual signal amplitude and temperature, account for charge injection during acquisition, and provide local supply bypassing to minimize supply-linked transients.

Resumo dos produtos recomendados

DG419LDJ+ Analog Devices Usado em: Audio Signal Routing, Battery-Operated Test Equipment, Communication Signal Multiplexing, Guidance and Control Systems, Military Radio Signal Routing, Precision Signal Isolation DG419LDJ PDIP package alternative in the DG419 family Usado em: Audio Signal Routing, Battery-Operated Test Equipment, Communication Signal Multiplexing, Guidance and Control Systems, Military Radio Signal Routing, Precision Signal Isolation
What is the DG419LDJ+ and what are its key specifications?
The DG419LDJ+ is a single-channel SPDT CMOS analog switch with a maximum on-resistance of 35 ohms and an 8-pin PDIP package. According to the Analog Devices DG419 Data Sheet, Rev. 2, it operates from ±4.5 V to ±20 V, supports +3 V-compatible control when powered from ±12 V or ±15 V, and operates from -40°C to +85°C. It is intended for one-source-to-two-destination analog signal routing where low resistance, low leakage, and compact logic control are important.
Where can I download the DG419LDJ+ datasheet PDF?
The official DG419LDJ+ documentation is available from the Analog Devices DG419 product page, which links to the manufacturer DG419 Data Sheet, Rev. 2. Use the pin-description table, electrical characteristics, and application information from that document when designing the PCB. The product page is the preferred source because it also identifies current production documentation and related orderable package variants.
Where is the pinout for the DG419LDJ+?
The DG419LDJ+ uses an 8-pin PDIP package, and its complete pin assignment is shown in the manufacturer datasheet and accessible pinout documentation. The package contains a common terminal, two switched terminals, control input, positive supply, and ground connections. Use the numbered package drawing when assigning PCB tracks rather than inferring connections from terminal names, particularly because the common and switched paths are electrically distinct.
What supply voltage does the DG419LDJ+ require?
The DG419LDJ+ accepts dual supplies from ±4.5 V to ±20 V. According to the Analog Devices DG419 Data Sheet, Rev. 2, the device is compatible with +3 V logic control when operated from ±12 V or ±15 V supplies. Both supply rails and ground must be present within their specified limits before signals are applied, and the control pin must never exceed the logic limits stated for the chosen supply configuration.
What is the on-resistance of the DG419LDJ+?
The DG419LDJ+ has a maximum on-resistance of 35 ohms. The Analog Devices DG419 family also guarantees on-resistance matching within 3 ohms and flat on-resistance variation of no more than 4 ohms across the signal range. These parameters matter because resistance variation introduces signal-dependent insertion-loss changes, which can affect gain accuracy, attenuation, and matching between routed channels.
Is the DG419LDJ+ suitable for audio signal routing?
The DG419LDJ+ is suitable for low-level audio signal routing when its 35 ohm maximum on-resistance and flat-on-resistance guarantees meet the system budget. Analog Devices lists audio signal routing among the DG419L family applications. For high-impedance audio paths the resistance contribution may be acceptable, while low-impedance or precision gain stages may require a switch with substantially lower on-resistance.
What can replace the DG419LDJ+ as a drop-in component?
The DG419LDJ without the + ordering suffix is the closest documented package-compatible family alternative, while the DG419LDY+ uses an 8-pin SOIC package and therefore is not a drop-in replacement for a PDIP footprint. A broad five-part drop-in list cannot be established from the available manufacturer and cross-reference information. Confirm the exact pin arrangement, supply limits, control polarity, and temperature rating in the manufacturer datasheet before substitution.
Is DG419LDY+ the same as DG419LDJ+?
No. The DG419LDJ+ is a through-hole 8-pin PDIP device, while the DG419LDY+ is an 8-pin SOIC surface-mount version. Although both belong to the DG419L family and provide similar SPDT switching functions, their mechanical footprints and PCB land patterns differ. Replacing one with the other requires new routing and a suitable SOIC footprint rather than a direct board-level substitution.
When should I choose the DG419LDJ+ instead of the DG419LDY+?
Choose the DG419LDJ+ when the PCB requires a through-hole 8-pin PDIP footprint, particularly for prototypes, repair work, or manually assembled boards. Choose the DG419LDY+ when the design uses an 8-pin SOIC land pattern and benefits from compact surface-mount assembly. The electrical decision must also account for control logic, supply range, signal range, temperature grade, and manufacturer-specific ordering information.
How much charge injection and off-leakage does the DG419LDJ+ have?
The DG419LDJ+ family is specified for maximum charge injection of 10 pC and maximum off-leakage current below 5 nA at +85°C. According to the Analog Devices DG419 Data Sheet, Rev. 2, these characteristics reduce transient feedthrough and unwanted coupling between disconnected paths. Charge injection remains important in sampled, instrumentation, and precision measurement systems even when the nominal leakage specification is satisfactory.
Where can I buy DG419LDJ+ and check current availability?
Use the Request a Quote form on this page to request DG419LDJ+ availability, order quantity, and lead time from XAIPART. The current orderable quantity and delivery schedule should be confirmed at request time because component inventory changes independently of the device specification. The package is an 8-pin PDIP device, so specify the exact suffix DG419LDJ+ when submitting the request.
What is the price of DG419LDJ+?
The current DG419LDJ+ quotation is generated through the Request a Quote form on this page. Submit the required quantity, target delivery date, and acceptable packaging configuration to receive a current offer. The form is the appropriate channel for commercial terms, current stock status, and lead-time confirmation rather than relying on a static historical listing.
What is the lead time and stock status for DG419LDJ+?
Request current DG419LDJ+ stock and lead time through the Request a Quote form on this page. The manufacturer identifies the DG419 family as production, but available quantity and scheduling can vary by package, order quantity, and market conditions. Providing a forecast consumption profile and required delivery date allows the supplier to confirm the most appropriate supply commitment.
What are the key DG419LDJ+ specifications engineers should know?
The principal DG419LDJ+ specifications are 35 ohm maximum on-resistance, 3 ohm maximum on-resistance matching, 4 ohm maximum flat-on-resistance variation, 10 pC maximum charge injection, and less than 5 nA off-leakage at +85°C. The device also supports ±4.5 V to ±20 V dual supplies, +3 V-compatible control at ±12 V or ±15 V, and a -40°C to +85°C operating range in an 8-pin PDIP package.
Is the DG419LDJ+ compliant with RoHS and AEC-Q100?
The Analog Devices DG419 product page identifies the DG419 family as production, but the available technical summary does not explicitly state RoHS, REACH, or AEC-Q100 qualification for this exact 8-pin PDIP orderable. Treat those compliance fields as unknown until confirmed on the manufacturer product page or in the orderable-part documentation. Automotive qualification should not be inferred from the industrial temperature range alone.

Dados de referência de engenharia para DG419LDJ+ — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the DG419LDJ+ when the board uses an 8-pin PDIP footprint and needs a single SPDT route with low leakage and controlled on-resistance. It is a practical selection for audio routing, communication equipment, test systems, guidance and control circuits, and ruggedized radio products using compatible high-impedance signals. Select DG419LDJ when that exact non-plus ordering designation is the approved BOM entry and its commercial conditions are acceptable. Choose DG419LDY+ only when the PCB provides an 8-pin SOIC footprint and you intentionally accept a board-layout change. If the application requires substantially less than 35 ohm on-resistance, lower charge injection, a single supply, or a different channel count, do not treat these family options as direct substitutes. Review the manufacturer datasheet for signal amplitude, bandwidth, control thresholds, and exact production status before freezing the design.

Comparação com alternativas

Parâmetro Este produto DG419LDJ
Brand Analog Devices Analog Devices
Package 8-pin PDIP 8-pin PDIP
Configuration 1 x SPDT 1 x SPDT
Maximum On-Resistance 35 ohm 35 ohm maximum for the DG419 family
Minimum Dual-Supply Voltage ±4.5 V ±4.5 V
Maximum Dual-Supply Voltage ±20 V ±20 V
Operating Temperature -40°C to +85°C -40°C to +85°C for the DG419L family
Mounting Type Through-hole Through-hole
Logic Compatibility +3 V compatible at ±12 V or ±15 V supply +3 V compatible at ±12 V or ±15 V supply

Principais diferenciais

  • Through-hole routing option (vs DG419LDY+)
  • Guaranteed flat on-resistance (vs DG419LDJ)
  • Precision channel matching (vs DG419LDJ)

Notas de projeto

Route the common and switched signal terminals as short, controlled-impedance paths, especially when the selected source has a high bandwidth. Keep the analog signal traces away from the control input and supply pins to reduce capacitive coupling from switching edges. For the DIP outline, place a ground or supply-return guard where practical, but avoid long traces that could create an unintended antenna. Follow the pin and layout guidance in the manufacturer datasheet for the exact board implementation.

Decouple each supply rail directly at the device with a local low-inductance capacitor and provide a close ground return. The DG419LDJ+ requires dual supplies of at least ±4.5 V, so a 3.3 V-only system needs rail generation before the switch is enabled. Confirm control-pin levels for the selected supply condition; the +3 V compatibility statement applies to operation from ±12 V or ±15 V. Keep supply transients within the ±20 V maximum dual-supply rating.

Include switch capacitance, on-resistance, charge injection, and off-leakage in the signal-path error budget. The 35 ohm maximum on-resistance is usually most appropriate for high-impedance sources, while its 10 pC maximum charge injection can create a transient step when switching sampled signals. Capture a settled sample after each state change when the acquisition chain is sensitive to switching transients. Verify the complete bandwidth response rather than inferring it from DC resistance.

Do not treat DG419LDY+ as a direct replacement for DG419LDJ+ because the former uses an 8-pin SOIC footprint and the latter uses an 8-pin PDIP footprint. Likewise, do not infer single-supply operation from the +3 V logic-compatible description. Confirm supply polarity, control thresholds, terminal mapping, and signal limits against the manufacturer datasheet. The + marking is an ordering suffix and should be preserved when requesting the exact PDIP part.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The DG419 family is identified as production by Analog Devices, but exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not established for this exact orderable in the available information.

Dados verificados em: 2026-11-16 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

DG419LDJ+ datasheet DG419LDJ+ pinout DG419LDJ+ datasheet pdf DG419LDJ+ equivalent DG419LDJ+ replacement DG419LDJ+ drop-in replacement DG419LDJ+ vs DG419LDY+ DG419LDJ+ 35 ohm SPDT switch DG419LDJ+ PDIP-8 pinout DG419LDJ+ application circuit Analog Devices DG419LDJ+ DG419LDJ+ price DG419LDJ+ stock DG419LDJ+ cross reference DG419LDJ+ schematic

Componentes & termos relacionados

Analog Devices Maxim Integrated DG419LDJ+ DG419LDJ DG419LDY+ DG419L SPDT analog switch CMOS analog switch interface IC signal routing multiplexer on-resistance charge injection off-leakage current flat on-resistance logic-compatible control 8-pin PDIP through-hole package dual-supply operation audio signal routing communication systems military radios ESD withstand
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ