EFM32G890F32-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs
N.º da peça: EFM32G890F32-BGA112 ✓ AtivoEFM32G890F32-BGA112 Visão geral
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals such as serial interfaces, timers, and analog blocks. Within the product hierarchy, the EFM32G890F32 belongs to the ARM Cortex-M3 microcontroller class, the EFM32 Gecko family, and the broader embedded-control semiconductor category. Its combination of a 32-bit processor and low-power peripherals makes it suitable for battery-operated equipment and other embedded systems that must process data while limiting energy use.
The EFM32G890F32-BGA112 provides 32 KB of Flash program memory and 8 KB of SRAM, supporting firmware storage, working memory, and application state. Its listed digital interface resources include 90 I/O pins, three 16-bit timers, EBI/EMI, I2C, IrDA, SPI, SmartCard, and UART/USART connectivity. These interfaces allow the MCU to communicate with sensors, displays, external nonvolatile memory, transceivers, and other embedded peripherals without requiring multiple companion controllers.
Silicon Labs describes the EFM32G family as an energy-oriented platform with autonomous peripherals and low current draw in both active and sleep operating states. The family data sheet states that EFM32G devices can consume as little as 0.6 microamps in Stop mode and 180 microamps per megahertz in Run mode. These figures characterize the broader family and should be checked against the exact operating configuration, clock rate, and peripheral activity used in a finished design.
Typical uses include industrial sensor nodes, compact wireless-control equipment, battery-powered instruments, building-automation endpoints, wearable accessories, and low-power IoT controllers. In each case, the MCU can execute control logic while using its low-energy modes between external events. The 112-BGA package also supports compact PCB designs, although its fine pitch requires careful assembly planning, inspection access, and multilayer board construction.
Design the power rails and decoupling around the 3.3 V-class operating environment described for this device family, and use the pin-description tables in the manufacturer datasheet when assigning the 90 digital I/O pins. Confirm package ball assignments, exposed-pad treatment, supported supply tolerances, and peripheral multiplexing before release because those details are not reproduced in the product listing.
This product record combines the exact ordering information, memory configuration, package dimensions, core speed, interface list, and low-power family characteristics with practical considerations for PCB layout, firmware sizing, and sourcing. It also provides same-package alternatives and a parameter-by-parameter comparison so engineers can distinguish flash-capacity changes from true pin-compatible design choices.
Alternativas drop-in para EFM32G890F32-BGA112 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EFM32G890F32-BGA112 (mesmo formato e footprint) — diferindo em RAM.
EFM32G890F64-BGA112
✅ Drop-InConsulte o preço
Ver ficha técnica →EFM32G890F128-BGA112
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EFM32G890F16-BGA112
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EFM32G290F128-BGA112T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EFM32G890F32-BGA112T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EFM32G890F32-BGA112 Classificações máximas e características elétricas
| Core Processor | ARM Cortex-M3, 32-bit |
| Maximum CPU Frequency | 32 MHz |
| Program Memory | 32 KB Flash (32K x 8) |
| RAM | 8 KB |
| Digital I/O Pins | 90 pins |
| Timers | 3 x 16-bit |
| Encapsulamento | 112-BGA, 10 mm x 10 mm |
| Package Type | Ball Grid Array |
| Tipo de montagem | Surface Mount |
| Tensão de alimentação | 2.5 V or 3.3 V |
| Stop Mode Current | As low as 0.6 microamps |
| Run Mode Current | 180 microamps per MHz |
| Serial Interfaces | EBI/EMI, I2C, IrDA, SPI, SmartCard, UART/USART |
Guia de Configuração de Pinos do EFM32G890F32-BGA112 ball grid array
Configuração de pinos para EFM32G890F32-BGA112 (pacote ball grid array). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para EFM32G890F32-BGA112.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
EFM32G890F32-BGA112 é adequado para 6 aplicaçãos: Battery-Powered Sensor Nodes, Industrial Monitoring and Control, Low-Power IoT Gateways, Portable Medical Accessories, Building Automation Endpoints, Wearable and Personal Devices.
Battery-Powered Sensor Nodes
The EFM32G890F32-BGA112 fits battery-powered sensor nodes because its ARM Cortex-M3 core handles acquisition and local control at up to 32 MHz, while the EFM32G family supports very low-power operation. The manufacturer EFM32G datasheet states that family devices can consume as little as 0.6 microamps in Stop mode. Use the 32 KB of Flash for compact firmware and the 8 KB of RAM for working buffers, then connect sensors through I2C or SPI. Design the duty cycle around measurement intervals because active current depends on processing time and enabled peripherals.
Recomendado
Industrial Monitoring and Control
The EFM32G890F32-BGA112 is suitable for industrial monitoring equipment that combines local control with several communication peripherals. Its listed connectivity includes UART/USART, SPI, I2C, IrDA, EBI/EMI, and SmartCard, while three 16-bit timers support periodic sampling, motor timing, or industrial pulse counting. The 32 MHz Cortex-M3 core provides responsive control without requiring a separate communications processor. For deployed systems, confirm operating-temperature limits, EMC requirements, and the exact supply range against the manufacturer datasheet before selecting the MCU for a production environment.
Recomendado
Low-Power IoT Gateways
The EFM32G890F32-BGA112 can serve as the local controller in a compact IoT gateway that wakes periodically, reads sensors, and forwards information through a serial radio or network module. Its 90 digital I/O pins provide substantial interface capacity, and the presence of UART/USART, SPI, I2C, and IrDA supports multiple peripheral styles. The family's Run-mode figure of 180 microamps per megahertz gives engineers a basis for comparing operating budgets, although actual consumption depends on the selected clock, active peripherals, and duty cycle.
Recomendado
Portable Medical Accessories
The EFM32G890F32-BGA112 is appropriate for compact battery-powered accessories that perform simple control, logging, or communication rather than intensive diagnostic processing. Its low-power Gecko architecture helps separate standby consumption from active operation, and the 90 I/O pins can support buttons, indicators, sensors, and serial peripherals. A medical product design must still apply the applicable risk management, biocompatibility, electrical-safety, and validation processes for the finished device. Confirm the target temperature range and medical-market qualification status rather than inferring suitability from the MCU family name.
Recomendado
Building Automation Endpoints
The EFM32G890F32-BGA112 fits building-automation endpoints that combine room controls, sensor inputs, and communications over UART, I2C, or SPI. Its 90 I/O pins reduce the need for external digital expanders in connected room hardware, while the three 16-bit timers can support timing-intensive control tasks. The 112-BGA package supports compact equipment designs but requires a multilayer PCB, controlled assembly, and adequate escape routing. Validate relay-driver isolation, ESD requirements, and operating-temperature limits as separate system-level design requirements.
Recomendado
Wearable and Personal Devices
The EFM32G890F32-BGA112 is suitable for wearable accessories and personal devices where a 32-bit processor, modest memory, and low-power modes are needed in a compact assembly. The 10 mm by 10 mm 112-BGA package reduces board area compared with many leaded packages, although its ball pitch complicates prototype soldering and inspection. Its 32 KB Flash can hold a focused firmware image, while UART, SPI, I2C, and IrDA allow connection to sensors and companion radio modules. Confirm package warpage, assembly capability, and operating-temperature requirements during hardware planning.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EFM32G890F32-BGA112 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EFM32G890F64-BGA112 | EFM32G890F128-BGA112 | EFM32G890F16-BGA112 | EFM32G290F128-BGA112T | EFM32G890F32-BGA112T |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 112-BGA (10x10) | 112-BGA (10x10) | 112-BGA (10x10) | 112-BGA (10x10) | 112-BGA (10x10) | 112-BGA (10x10) |
| Core Processor | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 64 KB | 128 KB | 16 KB | 128 KB | 32 KB |
Principais diferenciais
- Balanced memory configuration (vs EFM32G890F16-BGA112)
- Lower memory demand than the F64 option (vs EFM32G890F64-BGA112)
- Direct same-package configuration match (vs EFM32G890F32-BGA112T)
Notas de projeto
Design the PCB and assembly process around the 112-BGA, 10 mm by 10 mm package. Use a multilayer board with a solid ground plane, route escape traces between ball rows, and provide adequate thermal and copper support beneath the device. Confirm pad geometry, solder-mask definition, paste volume, and package tolerances using the manufacturer land-pattern and assembly guidance before fabrication.
Follow the manufacturer recommendations for supply voltage, decoupling, power sequencing, and exposed-pad connection. Place the required bulk and high-frequency capacitors close to the relevant supply balls, with a short return path to the ground plane. Validate brownout behavior, startup sequencing, and current peaks caused by enabled peripherals rather than relying only on the nominal Run-mode current.
Assign every ball through the manufacturer pin-description table, including alternate peripheral functions, debug signals, clock sources, and supply pins. Leave programming and debug access available on the board, isolate analog-sensitive routes from switching nodes, and use solid reference planes for high-speed interfaces. A valid schematic symbol is not enough; the PCB footprint and ball map must correspond to the exact BGA ordering code.
Avoid treating the family-level current figures as exact product guarantees. The 0.6-microamp Stop-mode and 180-microamps-per-MHz Run-mode figures depend on the operating configuration. Measure the full sleep, wake, active, and peripheral-load sequence, then size the battery and regulator for peak current. Also avoid assuming that a memory-capacity change preserves every peripheral function without comparing the relevant datasheet tables.
Informações de conformidade
Compliance attributes are not stated in the available product records and have therefore not been inferred.