EFM32ZG210F16-B-QFN32 - 24MHz Cortex-M0+ MCU | Silicon Labs
N.º da peça: EFM32ZG210F16-B-QFN32 ✓ AtivoEFM32ZG210F16-B-QFN32 Visão geral
A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals such as timers, serial interfaces, and analog blocks. The EFM32ZG belongs to the Zero Gecko family of 32-bit ARM Cortex-M0+ microcontrollers, a low-power branch of embedded processors intended for portable sensing, control, communications, and metering products.
The EFM32ZG210F16-B-QFN32 operates at up to 24 MHz and includes 16 KB Flash, 4 KB RAM, and 24 digital I/O pins. Its supply range is 1.98 V to 3.8 V, making it suitable for low-voltage, single-supply systems. Two 16-bit timers support periodic measurement, motor-control timing, and general event handling. The family also provides 12-bit analog conversion features and a deep Stop mode that can reduce consumption to as little as 0.5 µA.
Silicon Labs emphasizes energy efficiency as a platform feature rather than an isolated low-power mode. The Zero Gecko architecture combines autonomous peripherals, high analog and digital integration, and rapid transitions between energy-saving states. Run-mode consumption is specified as low as 114 µA/MHz for the EFM32ZG family. These characteristics help minimize both active energy use and the time the system spends awake while peripherals perform measurements or transfers.
Typical uses include battery-powered sensors, smart meters, energy and gas monitoring, portable health equipment, connected industrial nodes, and compact consumer accessories. Its 24 GPIO pins and QFN footprint support dense mixed-signal products, while the Cortex-M0+ instruction set provides a common software platform for embedded control and connected products.
Designers should treat the exposed pad, decoupling, programming access, and low-current measurement as layout priorities. Place input and output capacitors close to their supply pins, provide a clean ground reference for analog measurements, and follow the manufacturer land pattern and programming guidance for the 32-pin QFN footprint. Verify the selected board against the exact B suffix ordering information before production release.
This product overview combines the manufacturer specifications, package details, family-level drop-in options, and engineering guidance needed to assess the EFM32ZG210F16-B-QFN32 for a new low-power embedded design. The comparison material also highlights memory-density choices within the same QFN32 family, helping engineers balance firmware capacity, board reuse, and low-power operation.
Alternativas drop-in para EFM32ZG210F16-B-QFN32 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EFM32ZG210F16-B-QFN32 (mesmo formato e footprint) — diferindo em Flash Memory, Package, Digital I/O Pins, RAM, Timer Count.
EFM32ZG210F16-QFN32
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EFM32ZG210F32-B-QFN32
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EFM32ZG210F8-B-QFN32
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →EFM32ZG210F4-B-QFN32
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →EFM32ZG210F16-B-QFN32R
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EFM32ZG210F16-B-QFN32 Classificações máximas e características elétricas
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Maximum CPU Frequency | 24 MHz |
| Flash Memory | 16 KB |
| RAM | 4 KB |
| Digital I/O Pins | 24 pins |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Timer Resolution | 16-bit |
| Timer Count | 2 timers |
| ADC Resolution | 12-bit |
| Encapsulamento | 32-QFN (6 mm × 6 mm) |
| Exposed Pad | Present |
| Tipo de montagem | Surface mount |
| Faixa de temperatura de operação | -40 °C to +85 °C |
| Stop-Mode Current | 0.5 µA minimum |
| Run-Mode Current | 114 µA/MHz |
| Processor Core | ARM Cortex-M0+ |
| Architecture | 32-bit RISC |
| Status RoHS | Compliant |
Guia de Configuração de Pinos do EFM32ZG210F16-B-QFN32 32-qfn (6 mm × 6 mm)
Configuração de pinos para EFM32ZG210F16-B-QFN32 (pacote 32-qfn (6 mm × 6 mm)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para EFM32ZG210F16-B-QFN32.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
EFM32ZG210F16-B-QFN32 é adequado para 6 aplicaçãos: Battery-Powered Sensor Nodes, Smart Metering, Energy and Gas Monitoring, Portable Health Devices, Industrial Control Modules, Connected Consumer Accessories.
Battery-Powered Sensor Nodes
The EFM32ZG210F16-B-QFN32 fits compact battery-operated sensors because it combines a 24 MHz Cortex-M0+ core with 16 KB Flash, 4 KB RAM, and low-power modes. The family can consume as little as 0.5 µA in Stop mode and 114 µA/MHz in Run mode, allowing the controller to wake for measurements and return to sleep quickly. Its 24 GPIO pins can support digital sensors, status indicators, and a low-power serial link. Designers should use sensor duty cycling, autonomous peripheral operation, and careful pull-resistor selection because radio and sensor leakage may dominate total system consumption.
Recomendado
Smart Metering
The EFM32ZG210F16-B-QFN32 is appropriate for smart-meter signal conditioning, data logging, and periodic utility measurement. Its 24 digital I/O pins provide interface capacity for pulse sensors, tamper inputs, and status controls, while the 12-bit conversion capability supports analog front-end measurement. The 24 MHz Cortex-M0+ processor can service multiple timers and communications tasks, and the 4 KB RAM is suitable for buffering samples without continuously operating a radio. A meter design should budget flash for calibration, event storage, security updates, and protocol handling; the F32 density option offers 32 KB when those requirements exceed 16 KB.
Recomendado
Energy and Gas Monitoring
The EFM32ZG210F16-B-QFN32 suits energy, gas, and water monitoring modules that repeatedly acquire measurements and must remain available on a constrained power budget. Its 24 MHz Cortex-M0+ core provides enough performance for sensor conditioning, compensation, and low-rate data processing, while two 16-bit timers help schedule sampling and detect pulses. The 1.98 V to 3.8 V supply range supports low-voltage sensor rails. In a gas meter, the MCU can supervise heaters, control a valve, and retain a safe state during fault conditions, but those safety functions require application-specific validation beyond the component specifications.
Recomendado
Portable Health Devices
The EFM32ZG210F16-B-QFN32 can serve as the control processor in a compact wearable or portable health accessory where battery life and board area are important. Its 24 GPIO pins can support sensors, buttons, display interfaces, and status LEDs, while 4 KB RAM can coordinate short data-acquisition and filtering tasks. The processor's 24 MHz clock and 16 KB Flash are sufficient for focused embedded firmware rather than a large graphical workload. Designers should minimize always-on peripherals, use the Stop mode when clinically appropriate, and verify that analog measurements and radio activity meet the product's accuracy and energy requirements.
Recomendado
Industrial Control Modules
The EFM32ZG210F16-B-QFN32 is suitable for compact industrial control modules that coordinate digital inputs, timing functions, and low-speed serial communication. Its two 16-bit timers and 24 GPIO pins provide resources for actuator sequencing, pulse counting, and machine-state monitoring. The 1.98 V to 3.8 V operating range allows connection to low-voltage industrial subsystems, while the QFN package supports dense board layouts. The MCU should be paired with a regulator and communication interface selected for the installation. Isolation, surge protection, environmental limits, and functional-safety requirements are system-level concerns and must be addressed independently of the microcontroller.
Recomendado
Connected Consumer Accessories
The EFM32ZG210F16-B-QFN32 can serve as the low-power control MCU in a connected consumer accessory, handling buttons, indicators, sensor inputs, and a local communications interface. Its 24 MHz Cortex-M0+ core is appropriate for protocol framing and device-state management, while the 4 KB RAM and 16 KB Flash support compact embedded applications. The family-level 0.5 µA Stop-mode figure and 114 µA/MHz Run-mode figure help tune average consumption when the accessory spends most of its time asleep. Firmware partitioning should leave memory for radio or network code where it is linked, or use an F32 variant if that code exceeds the 16 KB Flash budget.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EFM32ZG210F16-B-QFN32 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EFM32ZG210F16-QFN32 | EFM32ZG210F32-B-QFN32 | EFM32ZG210F8-B-QFN32 | EFM32ZG210F4-B-QFN32 | EFM32ZG210F16-B-QFN32R |
|---|---|---|---|---|---|---|
| Package | 32-QFN (6 mm × 6 mm) | 32-QFN (6 mm × 6 mm) | 32-QFN (6 mm × 6 mm) | 32-QFN (6 mm × 6 mm) | 32-QFN (6 mm × 6 mm) | 32-QFN (6 mm × 6 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| CPU Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Frequency | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz |
| Flash Memory | 16 KB | 16 KB | 32 KB | 8 KB | 4 KB | 16 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Digital I/O Pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Supply Voltage Range | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V |
| Timer Configuration | 2 × 16-bit timers | 2 × 16-bit timers | 2 × 16-bit timers | 2 × 16-bit timers | 2 × 16-bit timers | 2 × 16-bit timers |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
Principais diferenciais
- Balanced embedded memory configuration (vs EFM32ZG210F32-B-QFN32)
- Greater firmware margin than reduced-density variants (vs EFM32ZG210F8-B-QFN32)
- Lower-power platform for compact embedded systems (vs EFM32TG210F16-QFN32)
- Compact 24-I/O implementation (vs EFM32ZG110F8-B-QFN24R)
Notas de projeto
Use the exact 32-QFN land pattern from the manufacturer package drawing, including the exposed-pad geometry, thermal-via arrangement, and solder-mask policy. Keep decoupling capacitors close to the supply and ground pins, provide a continuous return path beneath the device, and route sensitive analog inputs away from switching nodes. The exposed pad is normally the ground connection, but its net assignment and via pattern must follow the package documentation rather than a generic QFN32 footprint.
Design the 1.98 V to 3.8 V supply for both transient response and low-current operation. Place the required bulk and high-frequency decoupling at the power pins, verify regulator startup against the device's requirements, and measure the rail during sleep-to-run transitions. A low quiescent regulator is important because the MCU can enter a 0.5 µA Stop state, while board leakage, pull resistors, and external sensors may dominate the final standby current.
Confirm the complete ordering code before releasing a BOM or PCB. EFM32ZG210F16-QFN32 and EFM32ZG210F16-B-QFN32R can represent related ordering configurations rather than distinct functional designs, while F32, F8, and F4 variants change flash capacity. Also verify programming access, exposed-pad treatment, and temperature requirements against the exact part. Substitution should never be based on the 32-pin QFN outline alone.
Reserve debug and programming access before placing the small QFN device. Route the required programming signals to accessible pads or test points and keep probe ground returns short. For analog measurements, use a quiet ground reference and separate sensitive inputs from timer-driven or digital outputs. The 24 MHz core can create fast edge currents, so return-path continuity and supply-loop minimization are as important as the nominal component footprint.
Informações de conformidade
The component listing identifies the EFM32ZG210F16-B-QFN32 as RoHS compliant. No separate REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was established.