Silicon Labs

EFM32ZG210F16-B-QFN32 - 24MHz Cortex-M0+ MCU | Silicon Labs

MPN: EFM32ZG210F16-B-QFN32 ✓ Hoạt động
1.98 V to 3.8 V Vdss 0.5 µA minimum Id 32-QFN (6 mm × 6 mm) Package 24 MHz Speed 16 KB Memory
MOQ: 1 |

EFM32ZG210F16-B-QFN32 Tóm tắt

The Silicon Labs EFM32ZG210F16-B-QFN32 is a 24 MHz, 32-bit ARM Cortex-M0+ microcontroller with 16 KB of embedded Flash memory, 4 KB of RAM, 24 digital I/O pins, and a 32-pin QFN package measuring 6 mm by 6 mm. Designed for energy-sensitive and battery-operated equipment, it combines a compact embedded system with low-power operating modes, fast wake-up behavior, and autonomous peripheral operation.

A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals such as timers, serial interfaces, and analog blocks. The EFM32ZG belongs to the Zero Gecko family of 32-bit ARM Cortex-M0+ microcontrollers, a low-power branch of embedded processors intended for portable sensing, control, communications, and metering products.

The EFM32ZG210F16-B-QFN32 operates at up to 24 MHz and includes 16 KB Flash, 4 KB RAM, and 24 digital I/O pins. Its supply range is 1.98 V to 3.8 V, making it suitable for low-voltage, single-supply systems. Two 16-bit timers support periodic measurement, motor-control timing, and general event handling. The family also provides 12-bit analog conversion features and a deep Stop mode that can reduce consumption to as little as 0.5 µA.

Silicon Labs emphasizes energy efficiency as a platform feature rather than an isolated low-power mode. The Zero Gecko architecture combines autonomous peripherals, high analog and digital integration, and rapid transitions between energy-saving states. Run-mode consumption is specified as low as 114 µA/MHz for the EFM32ZG family. These characteristics help minimize both active energy use and the time the system spends awake while peripherals perform measurements or transfers.

Typical uses include battery-powered sensors, smart meters, energy and gas monitoring, portable health equipment, connected industrial nodes, and compact consumer accessories. Its 24 GPIO pins and QFN footprint support dense mixed-signal products, while the Cortex-M0+ instruction set provides a common software platform for embedded control and connected products.

Designers should treat the exposed pad, decoupling, programming access, and low-current measurement as layout priorities. Place input and output capacitors close to their supply pins, provide a clean ground reference for analog measurements, and follow the manufacturer land pattern and programming guidance for the 32-pin QFN footprint. Verify the selected board against the exact B suffix ordering information before production release.

This product overview combines the manufacturer specifications, package details, family-level drop-in options, and engineering guidance needed to assess the EFM32ZG210F16-B-QFN32 for a new low-power embedded design. The comparison material also highlights memory-density choices within the same QFN32 family, helping engineers balance firmware capacity, board reuse, and low-power operation.

Bộ thay thế dễ dàng lắp đặt cho EFM32ZG210F16-B-QFN32 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EFM32ZG210F16-B-QFN32 (cùng hình factor và footprint) — khác nhau ở Flash Memory, Package, Digital I/O Pins, RAM, Timer Count.

Silicon Labs
Flash Memory: 4 KB (4K x 8)
Package: 32-QFN (6 mm x 6 mm)
RAM: 2 KB
So sánh với EFM32ZG210F16-B-QFN32 →
Silicon Labs
Flash Memory: 8 KB (8K x 8)
Package: 32-QFN (6 x 6 mm)
Digital I/O Pins: 24
So sánh với EFM32ZG210F16-B-QFN32 →

EFM32ZG210F16-QFN32

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 32-QFN (6 mm × 6 mm)
Same 24 MHz Cortex-M0+ core, 16 KB Flash, 4 KB RAM, and QFN32 footprint; ordering-temperature suffix differs

📋 Tham chiếu thay thế (không có trong danh mục)

EFM32ZG210F32-B-QFN32

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 32-QFN (6 mm × 6 mm)
Flash increases from 16 KB to 32 KB, a 100% increase; CPU speed and RAM remain unchanged

📋 Tham chiếu thay thế (không có trong danh mục)

EFM32ZG210F8-B-QFN32

✅ Drop-In ⚠️ Thông số chưa được xác minh
Silicon Labs
📦 32-QFN (6 mm × 6 mm)
32-bit ARM Cortex-M0+ microcontroller · EFM32 Zero Gecko · 24 MHz · 8 KB (8K x 8) · 2 KB · 24 · 2 x 16-bit timers · 1.98 V to 3.8 V

Liên hệ để biết giá

Xem tài liệu →

EFM32ZG210F4-B-QFN32

✅ Drop-In ⚠️ Thông số chưa được xác minh
Silicon Labs
📦 32-QFN (6 mm × 6 mm)
32-bit ARM Cortex-M0+ microcontroller · EFM32 Zero Gecko · 24 MHz · 4 KB (4K x 8) · 2 KB · 24 pins · 2 x 16-bit timers · 1.98 V to 3.8 V

Liên hệ để biết giá

Xem tài liệu →

EFM32ZG210F16-B-QFN32R

✅ Drop-In
📦 32-QFN (6 mm × 6 mm)
Same electrical configuration and QFN32 footprint; R denotes reel packaging rather than a functional change

📋 Tham chiếu thay thế (không có trong danh mục)

EFM32ZG210F16-B-QFN32 Tỷ lệ tối đa & tính chất điện

Product Type 32-bit ARM Cortex-M0+ microcontroller
Maximum CPU Frequency 24 MHz
Flash Memory 16 KB
RAM 4 KB
Digital I/O Pins 24 pins
Supply Voltage Range 1.98 V to 3.8 V
Timer Resolution 16-bit
Timer Count 2 timers
ADC Resolution 12-bit
Hộp 32-QFN (6 mm × 6 mm)
Exposed Pad Present
Kiểu lắp đặt Surface mount
Khoảng nhiệt độ hoạt động -40 °C to +85 °C
Stop-Mode Current 0.5 µA minimum
Run-Mode Current 114 µA/MHz
Processor Core ARM Cortex-M0+
Architecture 32-bit RISC
Trạng thái RoHS Compliant

Hướng dẫn cấu hình chân EFM32ZG210F16-B-QFN32 32-qfn (6 mm × 6 mm)

Cấu hình chân cho EFM32ZG210F16-B-QFN32 (32-qfn (6 mm × 6 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 32-qfn (6 mm × 6 mm) cho EFM32ZG210F16-B-QFN32

Không có dữ liệu chân cụ thể sẵn có cho EFM32ZG210F16-B-QFN32.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

EFM32ZG210F16-B-QFN32 phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Nodes, Smart Metering, Energy and Gas Monitoring, Portable Health Devices, Industrial Control Modules, Connected Consumer Accessories.

🧩

Battery-Powered Sensor Nodes

The EFM32ZG210F16-B-QFN32 fits compact battery-operated sensors because it combines a 24 MHz Cortex-M0+ core with 16 KB Flash, 4 KB RAM, and low-power modes. The family can consume as little as 0.5 µA in Stop mode and 114 µA/MHz in Run mode, allowing the controller to wake for measurements and return to sleep quickly. Its 24 GPIO pins can support digital sensors, status indicators, and a low-power serial link. Designers should use sensor duty cycling, autonomous peripheral operation, and careful pull-resistor selection because radio and sensor leakage may dominate total system consumption.

⚡

Smart Metering

The EFM32ZG210F16-B-QFN32 is appropriate for smart-meter signal conditioning, data logging, and periodic utility measurement. Its 24 digital I/O pins provide interface capacity for pulse sensors, tamper inputs, and status controls, while the 12-bit conversion capability supports analog front-end measurement. The 24 MHz Cortex-M0+ processor can service multiple timers and communications tasks, and the 4 KB RAM is suitable for buffering samples without continuously operating a radio. A meter design should budget flash for calibration, event storage, security updates, and protocol handling; the F32 density option offers 32 KB when those requirements exceed 16 KB.

🏭

Energy and Gas Monitoring

The EFM32ZG210F16-B-QFN32 suits energy, gas, and water monitoring modules that repeatedly acquire measurements and must remain available on a constrained power budget. Its 24 MHz Cortex-M0+ core provides enough performance for sensor conditioning, compensation, and low-rate data processing, while two 16-bit timers help schedule sampling and detect pulses. The 1.98 V to 3.8 V supply range supports low-voltage sensor rails. In a gas meter, the MCU can supervise heaters, control a valve, and retain a safe state during fault conditions, but those safety functions require application-specific validation beyond the component specifications.

💊

Portable Health Devices

The EFM32ZG210F16-B-QFN32 can serve as the control processor in a compact wearable or portable health accessory where battery life and board area are important. Its 24 GPIO pins can support sensors, buttons, display interfaces, and status LEDs, while 4 KB RAM can coordinate short data-acquisition and filtering tasks. The processor's 24 MHz clock and 16 KB Flash are sufficient for focused embedded firmware rather than a large graphical workload. Designers should minimize always-on peripherals, use the Stop mode when clinically appropriate, and verify that analog measurements and radio activity meet the product's accuracy and energy requirements.

🏭

Industrial Control Modules

The EFM32ZG210F16-B-QFN32 is suitable for compact industrial control modules that coordinate digital inputs, timing functions, and low-speed serial communication. Its two 16-bit timers and 24 GPIO pins provide resources for actuator sequencing, pulse counting, and machine-state monitoring. The 1.98 V to 3.8 V operating range allows connection to low-voltage industrial subsystems, while the QFN package supports dense board layouts. The MCU should be paired with a regulator and communication interface selected for the installation. Isolation, surge protection, environmental limits, and functional-safety requirements are system-level concerns and must be addressed independently of the microcontroller.

📱

Connected Consumer Accessories

The EFM32ZG210F16-B-QFN32 can serve as the low-power control MCU in a connected consumer accessory, handling buttons, indicators, sensor inputs, and a local communications interface. Its 24 MHz Cortex-M0+ core is appropriate for protocol framing and device-state management, while the 4 KB RAM and 16 KB Flash support compact embedded applications. The family-level 0.5 µA Stop-mode figure and 114 µA/MHz Run-mode figure help tune average consumption when the accessory spends most of its time asleep. Firmware partitioning should leave memory for radio or network code where it is linked, or use an F32 variant if that code exceeds the 16 KB Flash budget.

Tóm tắt các sản phẩm được đề xuất

EFM32ZG210F16-B-QFN32 Silicon Labs Được sử dụng trong: Battery-Powered Sensor Nodes, Smart Metering, Energy and Gas Monitoring, Portable Health Devices, Industrial Control Modules, Connected Consumer Accessories EFM32ZG210F32-B-QFN32 Higher-memory firmware option Được sử dụng trong: Battery-Powered Sensor Nodes, Smart Metering, Industrial Control Modules, Connected Consumer Accessories EFM32ZG210F16-QFN32 Same-family non-B ordering option Được sử dụng trong: Energy and Gas Monitoring EFM32ZG210F8-B-QFN32 Silicon Labs Được sử dụng trong: Portable Health Devices
What are the key specifications of EFM32ZG210F16-B-QFN32?
The EFM32ZG210F16-B-QFN32 is a 24 MHz ARM Cortex-M0+ microcontroller with 16 KB Flash, 4 KB RAM, 24 digital I/O pins, and a 32-pin 6 mm × 6 mm QFN package. Silicon Labs specifies a 1.98 V to 3.8 V operating supply range for this device family. The combination of 16 KB Flash, 4 KB RAM, 12-bit conversion capability, and low-power modes makes it appropriate for compact embedded control and battery-powered sensing products.
Where can I download the EFM32ZG210F16-B-QFN32 datasheet PDF?
The official EFM32ZG datasheet is available as a PDF from Silicon Labs at https://www.silabs.com/documents/public/data-sheets/efm32zg-datasheet.pdf. It is the preferred document for pin descriptions, electrical characteristics, memory organization, package drawings, and application guidance. A component-specific PDF is also indexed at https://www.lcsc.com/datasheet/C1344091.pdf. Use the Silicon Labs document as the controlling reference when drawings or revisions differ between mirrors.
Where can I find the EFM32ZG210F16-B-QFN32 pinout?
The EFM32ZG210F16-B-QFN32 pinout is documented in the pin-description and package drawings of the official Silicon Labs EFM32ZG datasheet. The device uses a 32-pin QFN package with an exposed thermal pad and 24 digital I/O pins. Assign PCB tracks from the exact package drawing and pin-description table rather than relying on a generic QFN32 diagram, since exposed-pad connections and peripheral assignments are device-specific.
Is EFM32ZG210F16-B-QFN32 suitable for battery-powered applications?
Yes, the EFM32ZG210F16-B-QFN32 is suitable for battery-powered applications because the EFM32ZG family supports low-power operation, rapid wake-up, and autonomous peripheral activity. Silicon Labs specifies consumption as low as 0.5 µA in Stop mode and 114 µA/MHz in Run mode. The 1.98 V to 3.8 V supply range also accommodates low-energy rails, although the final battery life depends on sensor duty cycle, radio activity, and board leakage.
What is the power consumption of EFM32ZG210F16-B-QFN32?
The EFM32ZG210F16-B-QFN32 inherits the family efficiency figures of approximately 0.5 µA in Stop mode and 114 µA/MHz in Run mode, as stated in the Silicon Labs EFM32ZG datasheet. Actual board consumption can differ because of sensor leakage, pull resistors, regulator efficiency, and duty cycling. Measure the assembled product across sleep, active, and peripheral-operation states to establish the real energy budget.
How much Flash and RAM does EFM32ZG210F16-B-QFN32 have?
The EFM32ZG210F16-B-QFN32 contains 16 KB of Flash and 4 KB of RAM. According to the Silicon Labs device description, its 16 KB Flash is organized as 16K × 8, while the CPU executes code from the 32-bit ARM Cortex-M0+ core at up to 24 MHz. The 16 KB F16 variant is appropriate for compact firmware, whereas higher-density F32 options provide more program space when application growth is expected.
EFM32ZG210F16-B-QFN32 vs EFM32ZG210F32-B-QFN32: which should I choose?
Choose EFM32ZG210F16-B-QFN32 when 16 KB Flash is sufficient, and choose EFM32ZG210F32-B-QFN32 when the firmware needs up to 32 KB Flash. Both belong to the 24 MHz EFM32ZG210 family and use the same QFN32 device class, but the F32 density provides twice the program memory. Confirm the exact exposed-pad land pattern and pin compatibility against the manufacturer documentation before treating either part as a substitution.
When should I choose EFM32ZG210F16-B-QFN32 over a larger EFM32ZG variant?
Choose EFM32ZG210F16-B-QFN32 when 16 KB Flash and 4 KB RAM meet the application requirements and a 6 mm × 6 mm QFN footprint is beneficial. It is preferable to larger-density variants when code size is stable, board area is constrained, or a production design intentionally uses the same footprint across several density options. Move to an F32 variant when firmware growth or boot functionality would exceed the 16 KB memory budget.
What can replace EFM32ZG210F16-B-QFN32?
The closest same-family choices are EFM32ZG210F16-QFN32, EFM32ZG210F16-B-QFN32R, EFM32ZG210F32-B-QFN32, EFM32ZG210F8-B-QFN32, and EFM32ZG210F4-B-QFN32 when their corresponding ordering configurations use the same QFN32 footprint. These parts differ in ordering code or Flash density, so firmware partitioning, boot behavior, temperature grade, and exposed-pad layout must be checked before substitution.
Can EFM32ZG210F16-B-QFN32R replace EFM32ZG210F16-B-QFN32?
EFM32ZG210F16-B-QFN32R is a reel-oriented ordering variant of the same 24 MHz, 16 KB Flash EFM32ZG210F16 device in a 32-QFN package. It may suit production handling requirements when the manufacturer confirms the underlying device and land pattern are unchanged. Verify the manufacturer ordering information, temperature suffix, exposed-pad treatment, and reel orientation before using it as a drop-in replacement.
Is EFM32ZG210F16-B-QFN32 the same as EFM32TG210F16-QFN32?
No, EFM32TG210F16-QFN32 is not automatically interchangeable with EFM32ZG210F16-B-QFN32. Although both are 24 MHz, 16 KB Flash devices in 32-pin QFN packages, the EFM32TG series provides a different peripheral mix and feature set from the EFM32ZG Zero Gecko family. Review the pin-description tables and peripheral requirements before considering a board-level substitution.
What is the best Silicon Labs equivalent for EFM32ZG210F16-B-QFN32?
Within the Silicon Labs EFM32ZG210 family, EFM32ZG210F16-QFN32 is the closest equivalent to EFM32ZG210F16-B-QFN32 because both identify the 24 MHz, 16 KB Flash F16 device in a QFN32 package. EFM32ZG210F32-B-QFN32 is an alternative when more Flash memory is useful, while F8 and F4 options reduce program memory. Confirm the exact ordering code and package drawing for production use.
Where to buy EFM32ZG210F16-B-QFN32 online?
Use the Request a Quote form on this page to ask for EFM32ZG210F16-B-QFN32 availability, quantity, and delivery terms. The form allows the request to be matched to the exact 32-QFN ordering code without relying on a generic product description. Include your target quantity, acceptable packaging, and required delivery date when submitting the request.
What is the price of EFM32ZG210F16-B-QFN32?
Submit the EFM32ZG210F16-B-QFN32 inquiry through the Request a Quote form on this page for current pricing. The form is the appropriate channel because component pricing can vary with quantity, packaging, memory-programming requirements, and market conditions. Include the required order quantity and any programming or traceability requirements in the request.
What is the lead time and stock status of EFM32ZG210F16-B-QFN32?
Request the current EFM32ZG210F16-B-QFN32 stock position and lead time through the Request a Quote form on this page. State the required quantity, reel or tray preference, and target delivery date so the response reflects the exact ordering code. Silicon Labs lists the product family as active, but lot availability and production scheduling should be confirmed for each purchase.
What programming and debugging considerations apply to EFM32ZG210F16-B-QFN32?
The EFM32ZG210F16-B-QFN32 is programmed through the Silicon Labs programming and debug ecosystem, with the device-programming support page identifying EFM32ZG210F16 in the QFN32 configuration. Designers should reserve the programming signals described by the manufacturer datasheet and keep the SWD or serial-debug routing accessible without compromising the small 6 mm × 6 mm land pattern.

Dữ liệu tham khảo kỹ thuật cho EFM32ZG210F16-B-QFN32 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose EFM32ZG210F16-B-QFN32 when an application needs a 24 MHz Cortex-M0+ controller, 16 KB Flash, 4 KB RAM, and 24 GPIO pins in a compact 6 mm × 6 mm QFN package. It is especially attractive for battery-powered sensing, smart metering, and portable accessories where the family's 0.5 µA Stop-mode capability can reduce idle energy. Choose EFM32ZG210F32-B-QFN32 when firmware, boot code, or communication stacks require more than 16 KB Flash. Choose an F8 or F4 density only when reducing flash memory is more important than firmware headroom. EFM32ZG210F16-QFN32 or the -B-QFN32R ordering variant may be preferable for a shared board strategy, but the exact suffix, reel requirements, and manufacturer package documentation must be checked before substitution.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này EFM32ZG210F16-QFN32 EFM32ZG210F32-B-QFN32 EFM32ZG210F8-B-QFN32 EFM32ZG210F4-B-QFN32 EFM32ZG210F16-B-QFN32R
Package 32-QFN (6 mm × 6 mm) 32-QFN (6 mm × 6 mm) 32-QFN (6 mm × 6 mm) 32-QFN (6 mm × 6 mm) 32-QFN (6 mm × 6 mm) 32-QFN (6 mm × 6 mm)
Brand Silicon Labs Silicon Labs Silicon Labs Silicon Labs Silicon Labs Silicon Labs
CPU Core ARM Cortex-M0+ ARM Cortex-M0+ ARM Cortex-M0+ ARM Cortex-M0+ ARM Cortex-M0+ ARM Cortex-M0+
Maximum Frequency 24 MHz 24 MHz 24 MHz 24 MHz 24 MHz 24 MHz
Flash Memory 16 KB 16 KB 32 KB 8 KB 4 KB 16 KB
RAM 4 KB 4 KB 4 KB 4 KB 4 KB 4 KB
Digital I/O Pins 24 pins 24 pins 24 pins 24 pins 24 pins 24 pins
Supply Voltage Range 1.98 V to 3.8 V 1.98 V to 3.8 V 1.98 V to 3.8 V 1.98 V to 3.8 V 1.98 V to 3.8 V 1.98 V to 3.8 V
Timer Configuration 2 × 16-bit timers 2 × 16-bit timers 2 × 16-bit timers 2 × 16-bit timers 2 × 16-bit timers 2 × 16-bit timers
ADC Resolution 12-bit 12-bit 12-bit 12-bit 12-bit 12-bit

Bảo phân biệt quan trọng

  • Balanced embedded memory configuration (vsEFM32ZG210F32-B-QFN32)
  • Greater firmware margin than reduced-density variants (vsEFM32ZG210F8-B-QFN32)
  • Lower-power platform for compact embedded systems (vsEFM32TG210F16-QFN32)
  • Compact 24-I/O implementation (vsEFM32ZG110F8-B-QFN24R)

Ghi chú thiết kế

Use the exact 32-QFN land pattern from the manufacturer package drawing, including the exposed-pad geometry, thermal-via arrangement, and solder-mask policy. Keep decoupling capacitors close to the supply and ground pins, provide a continuous return path beneath the device, and route sensitive analog inputs away from switching nodes. The exposed pad is normally the ground connection, but its net assignment and via pattern must follow the package documentation rather than a generic QFN32 footprint.

Design the 1.98 V to 3.8 V supply for both transient response and low-current operation. Place the required bulk and high-frequency decoupling at the power pins, verify regulator startup against the device's requirements, and measure the rail during sleep-to-run transitions. A low quiescent regulator is important because the MCU can enter a 0.5 µA Stop state, while board leakage, pull resistors, and external sensors may dominate the final standby current.

Confirm the complete ordering code before releasing a BOM or PCB. EFM32ZG210F16-QFN32 and EFM32ZG210F16-B-QFN32R can represent related ordering configurations rather than distinct functional designs, while F32, F8, and F4 variants change flash capacity. Also verify programming access, exposed-pad treatment, and temperature requirements against the exact part. Substitution should never be based on the 32-pin QFN outline alone.

Reserve debug and programming access before placing the small QFN device. Route the required programming signals to accessible pads or test points and keep probe ground returns short. For analog measurements, use a quiet ground reference and separate sensitive inputs from timer-driven or digital outputs. The 24 MHz core can create fast edge currents, so return-path continuity and supply-loop minimization are as important as the nominal component footprint.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The component listing identifies the EFM32ZG210F16-B-QFN32 as RoHS compliant. No separate REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was established.

Dữ liệu được xác minh vào: 2026-11-15 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

EFM32ZG210F16-B-QFN32 datasheet EFM32ZG210F16-B-QFN32 pinout EFM32ZG210F16-B-QFN32 datasheet pdf EFM32ZG210F16-B-QFN32 specifications EFM32ZG210F16-B-QFN32 equivalent EFM32ZG210F16-B-QFN32 replacement EFM32ZG210F16-B-QFN32 price EFM32ZG210F16-B-QFN32 stock Silicon Labs EFM32ZG210F16-B-QFN32 EFM32ZG210F16-B-QFN32 QFN32 footprint EFM32ZG210F16-B-QFN32 vs EFM32TG210F16-QFN32 EFM32ZG210F16 battery powered application

Các bộ phận và thuật ngữ liên quan

Silicon Labs EFM32ZG210F16-B-QFN32 EFM32ZG210F16-QFN32 EFM32ZG210F32-B-QFN32 EFM32ZG210F8-B-QFN32 EFM32ZG210F4-B-QFN32 EFM32ZG210F16-B-QFN32R ARM Cortex-M0+ Zero Gecko microcontroller embedded microcontroller 32-bit RISC processor low-power embedded system QFN-32 surface-mount package exposed pad embedded Flash memory static RAM 1.98 V to 3.8 V supply 24 MHz clock 12-bit ADC 16-bit timer Stop mode autonomous peripheral operation battery-powered sensing smart metering RoHS
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ