EPF10K100BQC208-1 - 100K FLEX FPGA 6144 RAM 208-PQFP | Altera
N.º da peça: EPF10K100BQC208-1 ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $38.5 | $38,50 |
| 10 | $32.75 | $327,50 |
| 100 | $27.4 | $2.740,00 |
| 500 | $23.9 | $11.950,00 |
| 1.000 | $21.2 | $21.200,00 |
EPF10K100BQC208-1 Visão geral
Background: A Field Programmable Gate Array (FPGA) is a semiconductor integrated circuit composed of an array of configurable logic blocks (CLBs), programmable interconnects, and I/O cells that designers can reconfigure after manufacture to implement arbitrary digital logic. FPGAs sit above general-purpose microcontrollers and below custom ASICs in the design complexity pyramid - they offer higher integration than discrete logic but lower per-unit cost than a full ASIC at low volume. Within that hierarchy, the FLEX 10K family is positioned as a high-density programmable logic device (PLD) using a fine-grained architecture with embedded array blocks (EABs) that can be configured as memory or wide fan-in logic, giving it DSP-friendly characteristics for its generation.
Key features of the EPF10K100BQC208-1 include 6144 total RAM bits organized as 576 logic elements with embedded memory, a single 5 V supply rail, an internal combinatorial propagation delay quoted at 11 ns for representative loading conditions, and a 208-pin PQFP plastic package with gull-wing leads. The device is reconfigurable in-system via SRAM configuration cells, allowing unlimited reprogramming cycles during development and in-field updates.
From an architectural standpoint, the FLEX 10K device uses a continuous SRAM routing structure called the FastTrack interconnect, which provides predictable timing across all logic paths - a meaningful advantage over older segmented interconnect architectures. Each logic element contains a 4-input look-up table, a programmable flip-flop, and a carry chain for fast arithmetic, while embedded array blocks provide 2 Kbit memory blocks usable as RAM, ROM, or wide function generators.
Typical applications include glue logic replacement, custom state-machine controllers, interface bridges between microprocessors and peripherals, DSP preprocessing blocks, and legacy industrial-control upgrades where the 5 V-tolerant I/O and PQFP-208 footprint simplify PCB integration. Designers using this device typically work with the Altera MAX+PLUS II or Quartus MAX+PLUS legacy toolchain.
Design consideration: because the configuration is volatile SRAM, the FPGA must be loaded from a serial or parallel configuration EPROM on every power-up, and in-system reprogramming must respect the CONF_DONE handshake timing defined in the FLEX 10K datasheet family. Engineers planning a new design around this part should also evaluate Cyclone or MAX II families as lower-cost 5 V-tolerant alternatives where pin count is moderate.
This page consolidates distributor pricing, 208-PQFP drop-in alternatives within the FLEX 10K family, and practical configuration/PCB design notes not all gathered in a single place on the original datasheet.
Alternativas drop-in para EPF10K100BQC208-1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPF10K100BQC208-1 (mesmo formato e footprint) — diferindo em Total RAM Bits, Series, Operating Temperature, Configuration Method, Package.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPF10K100BQC208-2
✅ Drop-In✓ Em estoque
$82 / unidade
Ver ficha técnica →EPF10K100BQC208-3
✅ Drop-In✓ Em estoque
$24.5 / unidade
Ver ficha técnica →EPF10K100BQC208-1N
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EPF10K100BQC208-1 Classificações máximas e características elétricas
| Series | FLEX-10K |
| Family | FLEX 10K (SRAM-based FPGA) |
| Logic Elements | 576 |
| Total RAM Bits | 6144 |
| Tensão de alimentação | 4.75 V to 5.25 V |
| Combinatorial tpd (typ.) | 11 ns |
| Speed Grade | -1 |
| Encapsulamento | 208-BFQFP (PQFP-208, 28x28 mm) |
| Tipo de montagem | Surface Mount |
| Configuration Memory | SRAM (volatile, in-system reconfigurable) |
Guia de Configuração de Pinos do EPF10K100BQC208-1 208-bfqfp (pqfp-208, 28x28 mm)
Configuração de pinos para EPF10K100BQC208-1 (pacote 208-bfqfp (pqfp-208, 28x28 mm)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para EPF10K100BQC208-1.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
EPF10K100BQC208-1 é adequado para 6 aplicaçãos: Legacy 5 V Glue Logic Replacement, Industrial Control State Machine, Custom Microprocessor Peripheral Bridge, DSP Preprocessing Block, Interface Protocol Translator, Legacy Aerospace and Defense Avionics Bus.
Legacy 5 V Glue Logic Replacement
The EPF10K100BQC208-1's 5 V-tolerant I/O and 576 logic elements make it ideal for replacing discrete 74-series glue logic on legacy PCBs. Its 6144 RAM bits and EAB-based architecture allow compact state-machine and bus-arbiter designs that previously required dozens of TTL packages. The 208-PQFP footprint fits the same board area as a small array of standard-logic ICs while providing reprogrammable behavior, shortening debug cycles. Designers typically use MAX+PLUS II to compile the design and a serial configuration EPROM for stand-alone boot.
Recomendado
Industrial Control State Machine
With 576 logic elements and deterministic FLEX 10K FastTrack interconnect routing, the EPF10K100BQC208-1 suits industrial-control state machines where predictable timing matters more than raw gate count. The 5 V supply rails simplify integration with 5 V sensors, relay drivers, and HMI displays. Industrial designs benefit from the industrial-temperature EPF10K100BQC208-1N variant, which has the same 208-PQFP footprint but extended operating range for factory-floor deployments.
Recomendado
Custom Microprocessor Peripheral Bridge
The EPF10K100BQC208-1's 6144 RAM bits and 576 logic elements are well-matched to bridge custom peripherals to legacy 8-bit and 16-bit microprocessors. Designers use the FLEX 10K EABs as dual-port RAM buffers between the CPU bus and DMA channels, while the programmable I/O cells handle the voltage translation between 5 V micro and 3.3 V peripherals. The 208-PQFP package gives enough I/O for 24-32 address/data signals plus interrupt and DMA handshaking.
Recomendado
DSP Preprocessing Block
FLEX 10K EABs can be configured as wide multipliers and adders, letting the EPF10K100BQC208-1 serve as a fixed-point DSP preprocessing engine for FIR filters or correlation blocks in audio and baseband designs. The 11 ns typical tpd on the -1 speed grade is sufficient for many kHz-range DSP tasks when pipelined across multiple logic elements. Designers pair it with an external DAC and use the FLEX 10K's parallel configuration mode for fast boot from a parallel EPROM.
Recomendado
Interface Protocol Translator
The EPF10K100BQC208-1's reprogrammable I/O cells let it translate between legacy interfaces such as ISA bus, PC/104, or VME on one side and modern peripherals on the other. The 208-PQFP package provides enough I/O for a 16-bit data bus plus address, control, and interrupt signals. With its 5 V tolerance, the part can sit directly on legacy 5 V buses without external level shifters, simplifying mixed-voltage board designs.
Recomendado
Legacy Aerospace and Defense Avionics Bus
Long-lifecycle aerospace and defense programs still rely on the EPF10K100BQC208-1 because of its 5 V tolerance, mature MAX+PLUS II toolchain, and field-proven reliability. The 208-PQFP package supports high-vibration environments when properly underfilled or socketed. Many defense OEMs continue to maintain bitstream IP for this device, and authorized legacy distributors like Rochester Electronics guarantee multi-decade supply continuity for these programs.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPF10K100BQC208-1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPF10K100BQC208-2 | EPF10K100BQC208-3 | EPF10K100BQC208-1N |
|---|---|---|---|---|
| Package | 208-BFQFP (PQFP-208, 28x28 mm) | 208-BFQFP (PQFP-208) - same | 208-BFQFP (PQFP-208) - same | 208-BFQFP (PQFP-208) - same |
| Brand | Altera (Intel) | Altera (Intel) - same | Altera (Intel) - same | Altera (Intel) - same |
| Series | FLEX 10K | FLEX 10K - same | FLEX 10K - same | FLEX 10K - same |
| Speed Grade | -1 (slowest) | -2 (faster) | -3 (fastest) | -1N (industrial temp) |
| Logic Elements | 576 | 576 | 576 | 576 |
| Total RAM Bits | 6144 | 6144 | 6144 | 6144 |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Temperature Grade | Commercial | Commercial | Commercial | Industrial/Extended |
Principais diferenciais
- Slowest speed grade (-1) maximizes timing margin for low-speed legacy interfaces (vs EPF10K100BQC208-2)
- Identical 208-PQFP footprint simplifies PCB reuse across speed grades (vs EPF10K100BQC208-3)
- Industrial/extended temperature option in the same package (vs EPF10K100BQC208-1N)
Notas de projeto
Estimated: based on a typical FLEX 10K Icc of roughly 50-150 mA standby plus dynamic current proportional to toggle rate, a 5 V EPF10K100BQC208-1 design should budget at least 1 A of 5 V supply capacity per device, with bulk decoupling (47 uF or larger tantalum) near the VCC pins and 0.1 uF ceramic caps within 5 mm of every VCC/ground pair. Because the configuration is volatile SRAM, inrush during configuration can spike higher; size the regulator so it does not sag below 4.75 V during config.
The 208-PQFP package has a 0.5 mm lead pitch and gull-wing leads, which requires careful PCB layout: keep all traces at least 0.2 mm from the package edges, use solder mask dams between pads, and follow the Altera-recommended land pattern from the FLEX 10K datasheet family. Add a low-impedance ground pour directly under the package to reduce ground bounce. Use a socket (e.g. Yamaichi IC149-208) if you need to swap FPGAs during development without rework.
Do not assume the FLEX 10K bitstream is compatible with Cyclone, MAX, or any newer Intel/Altera device - the configuration formats are completely different and a wrong bitstream can leave the device unconfigured or in a high-Icc state. Always generate the bitstream in MAX+PLUS II or the legacy Quartus MAX+PLUS flow matched to the FLEX 10K device ID. Also confirm that the CONF_DONE pin rises within the datasheet-specified timeout, or the host microcontroller will misinterpret a failed configuration as a logic hang.
Informações de conformidade
Compliance data was not provided in the verified web data. The original PQFP-208 part predates many modern compliance declarations; contact the legacy distributor (Rochester Electronics) for the specific compliance certificate of the lot you receive.
