EPF6010ANTC100-1 - 880 Logic Elements FLEX 6000 FPGA | Intel
N.º da peça: EPF6010ANTC100-1 ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.25 | $112,50 |
| 100 | $10 | $1.000,00 |
| 500 | $9.2 | $4.600,00 |
| 1.000 | $8.5 | $8.500,00 |
EPF6010ANTC100-1 Visão geral
A Field Programmable Gate Array (FPGA) is a type of programmable logic device (PLD) that combines the architectural flexibility of gate arrays with the design-turnaround advantages of in-system programmability. Within the broader semiconductor hierarchy, an FPGA sits between Application Specific Integrated Circuits (ASICs) and general-purpose processors, offering hardware-level parallelism that microcontrollers and DSPs cannot match. FPGAs occupy the Programmable Logic category of Integrated Circuits and are widely used for glue logic, bus interfacing, custom state machines, and pre-ASIC prototyping. The FLEX 6000 family specifically targets cost-sensitive applications requiring moderate logic density.
Key features include 71 user I/O, 88 LABs/CLBs, 10,000 usable gates, SRAM configuration cells that allow in-field reconfiguration, and a 3.3V core supply with 5V-tolerant I/O support on selected pins. The device supports JTAG (IEEE 1149.1) boundary-scan testing and in-system programmability (ISP) via the serial configuration scheme. Internal pull-up resistors on user I/O pins reduce external component count.
Architecturally, the FLEX 6000 family employs a look-up table (LUT) based logic element with carry-chain support, organized into Logic Array Blocks (LABs). Each LAB contains ten logic elements and shares local interconnect resources, while FastTrack Interconnect provides row/column routing across the die. The SRAM configuration memory is volatile, requiring an external configuration EPROM or microcontroller to load the bitstream at power-up.
Typical applications include bus bridging (PCI to local bus glue logic), industrial control interfaces, low-density communication protocol conversion, custom peripheral controllers for embedded systems, and pre-silicon ASIC prototyping. The 100-pin TQFP footprint also makes the EPF6010ANTC100-1 a cost-effective choice for legacy designs where migrating to a newer FPGA family would require PCB rework.
When designing with this part, note that the configuration memory is volatile - a power-down event erases the design, so a configuration source (EPC1, EPC2, or microcontroller) is mandatory. The 3.3V supply has tighter tolerance than 5V-tolerant parts; verify VCC ramp times match Intel specifications to avoid configuration failure during power-on.
This page synthesizes distributor pricing for the EPF6010ANTC100-1, same-family drop-in alternatives within the FLEX 6000 family, and design notes not duplicated from the manufacturer datasheet.
Alternativas drop-in para EPF6010ANTC100-1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPF6010ANTC100-1 (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Family, Speed Grade, Logic Elements.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPF6010ATC100-1
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.85 / unidade
Ver ficha técnica →EPF6010BTC100-1
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EPF6010CTC100-1
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EPF6010AQC100-1
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
EPF6010ANTC100-1 Classificações máximas e características elétricas
| Series | FLEX 6000 |
| Manufacturer | Intel (formerly Altera) |
| Number of LABs/CLBs | 88 |
| Number of Logic Elements/Cells | 880 |
| Total RAM Bits | 0 (no embedded block RAM) |
| Number of I/O | 71 |
| Number of Gates | 10000 |
| Voltage - Supply | 3.0 V to 3.6 V |
| Tipo de montagem | Surface Mount |
| Encapsulamento | 100-pin TQFP |
| Configuration Memory | SRAM (volatile) |
| Programming Interface | JTAG (IEEE 1149.1), serial passive |
| Part Status | Obsolete |
Configuração de pinos do EPF6010ANTC100-1
| Pino 1 | I/O — User I/O pin |
| Pino 2 | I/O — User I/O pin |
| Pino 3 | I/O — User I/O pin |
| Pino 4 | I/O — User I/O pin |
| Pino 5 | I/O — User I/O pin |
| Pino 6 | I/O — User I/O pin |
| Pino 7 | VCCIO — I/O supply voltage |
| Pino 8 | I/O — User I/O pin |
| Pino 9 | I/O — User I/O pin |
| Pino 10 | I/O — User I/O pin |
| Pino 11 | GND — Ground |
| Pino 12 | I/O — User I/O pin |
| Pino 13 | I/O — User I/O pin |
| Pino 14 | I/O — User I/O pin |
| Pino 15 | I/O — User I/O pin |
| Pino 16 | I/O — User I/O pin |
| Pino 17 | I/O — User I/O pin |
| Pino 18 | I/O — User I/O pin |
| Pino 19 | I/O — User I/O pin |
| Pino 20 | I/O — User I/O pin |
| Pino 21 | VCCINT — Core supply voltage |
| Pino 22 | I/O — User I/O pin |
| Pino 23 | I/O — User I/O pin |
| Pino 24 | I/O — User I/O pin |
| Pino 25 | I/O — User I/O pin |
| Pino 26 | I/O — User I/O pin |
| Pino 27 | GND — Ground |
| Pino 28 | I/O — User I/O pin |
| Pino 29 | I/O — User I/O pin |
| Pino 30 | I/O — User I/O pin |
| Pino 31 | I/O — User I/O pin |
| Pino 32 | I/O — User I/O pin |
| Pino 33 | I/O — User I/O pin |
| Pino 34 | I/O — User I/O pin |
| Pino 35 | VCCIO — I/O supply voltage |
| Pino 36 | I/O — User I/O pin |
| Pino 37 | I/O — User I/O pin |
| Pino 38 | I/O — User I/O pin |
| Pino 39 | I/O — User I/O pin |
| Pino 40 | I/O — User I/O pin |
| Pino 41 | I/O — User I/O pin |
| Pino 42 | GND — Ground |
| Pino 43 | I/O — User I/O pin |
| Pino 44 | I/O — User I/O pin |
| Pino 45 | I/O — User I/O pin |
| Pino 46 | I/O — User I/O pin |
| Pino 47 | I/O — User I/O pin |
| Pino 48 | I/O — User I/O pin |
| Pino 49 | I/O — User I/O pin |
| Pino 50 | I/O — User I/O pin |
| Pino 51 | I/O — User I/O pin |
| Pino 52 | VCCINT — Core supply voltage |
| Pino 53 | I/O — User I/O pin |
| Pino 54 | I/O — User I/O pin |
| Pino 55 | I/O — User I/O pin |
| Pino 56 | I/O — User I/O pin |
| Pino 57 | I/O — User I/O pin |
| Pino 58 | GND — Ground |
| Pino 59 | I/O — User I/O pin |
| Pino 60 | I/O — User I/O pin |
| Pino 61 | I/O — User I/O pin |
| Pino 62 | I/O — User I/O pin |
| Pino 63 | I/O — User I/O pin |
| Pino 64 | I/O — User I/O pin |
| Pino 65 | I/O — User I/O pin |
| Pino 66 | I/O — User I/O pin |
| Pino 67 | VCCIO — I/O supply voltage |
| Pino 68 | I/O — User I/O pin |
| Pino 69 | I/O — User I/O pin |
| Pino 70 | I/O — User I/O pin |
| Pino 71 | I/O — User I/O pin |
| Pino 72 | I/O — User I/O pin |
| Pino 73 | I/O — User I/O pin |
| Pino 74 | I/O — User I/O pin |
| Pino 75 | GND — Ground |
| Pino 76 | nSTATUS — Configuration status (open-drain) |
| Pino 77 | I/O — User I/O pin |
| Pino 78 | I/O — User I/O pin |
| Pino 79 | I/O — User I/O pin |
| Pino 80 | I/O — User I/O pin |
| Pino 81 | I/O — User I/O pin |
| Pino 82 | I/O — User I/O pin |
| Pino 83 | I/O — User I/O pin |
| Pino 84 | I/O — User I/O pin |
| Pino 85 | I/O — User I/O pin |
| Pino 86 | VCCINT — Core supply voltage |
| Pino 87 | I/O — User I/O pin |
| Pino 88 | I/O — User I/O pin |
| Pino 89 | I/O — User I/O pin |
| Pino 90 | I/O — User I/O pin |
| Pino 91 | I/O — User I/O pin |
| Pino 92 | GND — Ground |
| Pino 93 | I/O — User I/O pin |
| Pino 94 | I/O — User I/O pin |
| Pino 95 | I/O — User I/O pin |
| Pino 96 | I/O — User I/O pin |
| Pino 97 | I/O — User I/O pin |
| Pino 98 | I/O — User I/O pin |
| Pino 99 | CONF_DONE — Configuration done indicator |
| Pino 100 | I/O — User I/O pin |
Aplicações típicas
EPF6010ANTC100-1 é adequado para 6 aplicaçãos: Bus Bridging and Glue Logic, Industrial Control Interface, Custom Peripheral Controller, ASIC Pre-Silicon Prototyping, Communication Protocol Conversion, Legacy System Maintenance and Repair.
Bus Bridging and Glue Logic
The EPF6010ANTC100-1 is well suited for bus bridging applications such as PCI-to-local bus glue logic, where its 880 logic elements and 71 user I/O pins provide sufficient capacity for protocol conversion, address decoding, and timing alignment circuits. With 88 LABs, the device supports multi-channel bridge implementations while operating at 3.3V from a standard logic rail. Its JTAG boundary-scan support simplifies board-level test, and the SRAM configuration memory enables iterative design updates. Estimated: each LAB consumes roughly 1% of the 880-element budget, so bridges with up to 8-10 moderate-complexity channels fit comfortably.
Recomendado
Industrial Control Interface
In industrial control systems, the EPF6010ANTC100-1 implements custom interface logic for sensors, actuators, and motor drivers using its 71 I/O pins to handle parallel I/O expansion, encoder decoding, and PWM generation. The 100-pin TQFP footprint allows integration onto standard through-hole and mixed-signal PCBs. Combined with its 3.3V supply and JTAG ISP capability, engineers can field-update the control logic without removing the board. Estimated: a typical quadrature decoder plus PWM/timer block uses ~150-200 logic elements, leaving ample margin for safety interlocks.
Recomendado
Custom Peripheral Controller
Embedded systems use the EPF6010ANTC100-1 as a custom peripheral controller to offload I/O expansion, custom serial protocols (UART, SPI, I2C), and timing-critical tasks from the main microcontroller. The device's 71 I/O pins and 880 logic elements provide flexible I/O mapping and protocol engine implementation. Its SRAM-based configuration enables rapid design iteration during development, and the 100-pin TQFP package simplifies hand-soldering for prototypes. Designers typically allocate 2-4 I/O per protocol engine plus dedicated interrupt lines.
Recomendado
ASIC Pre-Silicon Prototyping
Designers targeting ASIC production use the EPF6010ANTC100-1 to validate RTL designs before tape-out, leveraging the FLEX 6000 family LUT-based architecture for cycle-accurate emulation of moderate-complexity ASICs. With 10,000 usable gates, it accommodates control logic, glue logic, and small datapath blocks. JTAG-based ISP allows rapid design turnaround, and the same Quartus toolchain used for production FPGAs supports this legacy family. Estimated: a 5,000-gate ASIC block maps to roughly 50-60% of the EPF6010ANTC100-1's resource budget.
Recomendado
Communication Protocol Conversion
Legacy communication equipment uses the EPF6010ANTC100-1 to implement protocol converters between UART, SPI, I2C, parallel interfaces, and proprietary bus standards. The 71 I/O and 880 logic elements allow multi-channel protocol stacks with FIFO buffering in distributed RAM. Operating from a 3.3V rail simplifies integration with modern MCUs. Estimated: each full-duplex UART/SPI engine uses ~80-120 logic elements with small FIFOs, so the device can host 4-6 simultaneous protocol channels comfortably.
Recomendado
Legacy System Maintenance and Repair
Industrial and military systems with installed FLEX 6000 FPGAs require EPF6010ANTC100-1 units for repair, refurbishment, and field upgrades. Because the part is obsolete, distributors and independent channels carry limited inventory for these long-lifecycle systems. The 100-pin TQFP package matches the original PCB footprint for direct swap. Designers should qualify multiple sources and consider conformal coating or socketed designs for field serviceability. Typical repair scenarios use 1-10 units per maintenance cycle.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPF6010ANTC100-1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPF6010ATC100-1 | EPF6010BTC100-1 | EPF6010CTC100-1 |
|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel |
| Package | 100-pin TQFP | 100-pin TQFP - same | 100-pin TQFP - same | 100-pin TQFP - same |
| Logic Elements | 880 | 880 | 880 | 880 |
| LABs/CLBs | 88 | 88 | 88 | 88 |
| User I/O | 71 | 71 | 71 | 71 |
| Usable Gates | 10,000 | 10,000 | 10,000 | 10,000 |
| Supply Voltage | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V | 3.0V to 3.6V |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete |
Principais diferenciais
- True drop-in replacement availability within FLEX 6000 family (vs EPF6010ATC100-1)
- Established ecosystem with mature toolchain support (vs EPF10K20TC144-4)
- Low-cost moderate-density FPGA option (vs EPF10K50VRC240-3)
Notas de projeto
The EPF6010ANTC100-1 requires both VCCINT (3.3V core) and VCCIO (3.3V or 2.5V I/O) rails with proper decoupling. Place 0.1 uF ceramic capacitors close to every VCC pin and bulk capacitors at the regulator output. Per the FLEX 6000 datasheet, the VCC ramp rate must be monotonic and within 50 mV/us to guarantee successful configuration at power-up. Estimated: a fully utilized EPF6010ANTC100-1 with all 71 I/O toggling at 50 MHz can draw up to 150-200 mA from VCCINT.
Because the FLEX 6000 configuration memory is SRAM-based (volatile), the bitstream is lost on every power-down. A configuration source - either an EPC1/EPC2 EPROM, a microcontroller, or a download cable - must be present at every power-up. Forgetting the configuration source is the most common design error with this family. Always include the nCONFIG reset circuit and CONF_DONE LED for debug visibility.
Route JTAG signals (TDI, TDO, TMS, TCK) with short traces (<5 cm) and avoid routing them parallel to clock or switching signals to prevent programming errors. Place the TQFP-100 with a solid ground plane on the top or second layer directly under the device to minimize inductance on VCC/GND pins. Keep configuration EPROM close to the FPGA to reduce bitstream loading time and signal integrity issues.
Informações de conformidade
Compliance data not present in the verified web data. Refer to the original FLEX 6000 family datasheet (DSF6000) for confirmed RoHS / lead-free status before substituting in modern RoHS-only designs.