EPM3064ATC44-4N - 64-Macrocell 3.3V CPLD, 4.5ns TQFP-44 | Altera
N.º da peça: EPM3064ATC44-4N ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $6.29 | $6,29 |
| 10 | $5.66 | $56,60 |
| 100 | $4.62 | $462,00 |
| 1.000 | $4 | $4.000,00 |
| 10.000 | $3.45 | $34.500,00 |
EPM3064ATC44-4N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile, instantly-on programmable logic device built from a small number of macrocells interconnected by a central switch matrix. Compared to an FPGA, a CPLD offers deterministic timing, no configuration time, and is well suited to glue logic, bus decoding, state-machine, and interface-bridging tasks. The MAX 3000A family sits in Altera's classic EEPROM-based hierarchy, which preserves the bitstream in non-volatile memory and therefore powers up already configured.
Key features include 3.3-V core operation with 2.5-V/3.3-V VCCIO flexibility, multiVolt I/O for mixing 2.5-V and 3.3-V buses, IEEE Std. 1149.1 (JTAG) boundary-scan and IEEE Std. 1532 in-system programmability, four dedicated inputs, two global clock pins, and open-drain / programmable pull-up options. Per the datasheet, ISP via the JTAG interface allows reconfiguration on populated boards without removing the device.
Architecturally, each macrocell contains a programmable AND/OR array with a configurable flip-flop, while the interconnect matrix (the AIM - Altera Interconnect Matrix) provides deterministic, predictable routing delays independent of logic placement. This makes the part attractive for asynchronous and timing-critical interfaces.
Typical applications include bus decoding and address mapping, asynchronous state machines, I/O expansion for microcontrollers, glue logic for legacy 5-V to 3.3-V interfaces, and small interface-bridging functions (UART, I2C, SPI gating). The wide VCCIO range and JTAG ISP simplify board bring-up.
Design consideration: VCCIO must be tied to 2.5 V for 2.5-V outputs and 3.3 V for 3.3-V outputs; mixing levels requires careful rail planning. The EEPROM-based architecture means write/erase cycles are limited (per datasheet) - use ISP for development, not for in-field reconfiguration at high frequency.
This page synthesizes distributor stock and pricing, verified drop-in alternatives within the MAX 3000A family, and practical design notes not aggregated in a single datasheet view.
Alternativas drop-in para EPM3064ATC44-4N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPM3064ATC44-4N (mesmo formato e footprint) — diferindo em Package, Operating Temperature, RoHS Status, Programming Interface, Usable Gates.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPM3064ATC44-7N
✅ Drop-In✓ Em estoque
$2.3 / unidade
Ver ficha técnica →EPM3064ATC44-10N
✅ Drop-In✓ Em estoque
$5.1 / unidade
Ver ficha técnica →EPM3032ATC44-4N
✅ Drop-In✓ Em estoque
$1.78 / unidade
Ver ficha técnica →EPM3064ALC44-4N
✅ Drop-In✓ Em estoque
$4.8 / unidade
Ver ficha técnica →EPM3064ATC44-4N Classificações máximas e características elétricas
| Family | MAX 3000A |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macro Cells | 64 |
| Logic Array Blocks | 2 |
| Number of I/Os | 34 |
| Dedicated Inputs | 4 |
| Usable Gates | 1,250 |
| Propagation Delay (tpd) | 4.5 ns |
| Maximum Counter Frequency | 222.2 MHz |
| Supply Voltage (VCCINT) | 3.3 V |
| I/O Supply Voltage (VCCIO) | 2.5 V or 3.3 V |
| Programmability | EEPROM, in-system programmable (JTAG) |
| JTAG Support | IEEE Std. 1149.1 (boundary-scan) and IEEE Std. 1532 (ISP) |
| Temperatura de operação | 0C to +70C (commercial) |
| Encapsulamento | 44-pin TQFP |
| Tipo de montagem | Surface Mount |
Configuração de pinos do EPM3064ATC44-4N
| Pino 1 | I/O — User I/O pin (function per macrocell assignment) |
| Pino 2 | I/O — User I/O pin |
| Pino 3 | I/O — User I/O pin |
| Pino 4 | I/O — User I/O pin |
| Pino 5 | I/O — User I/O pin |
| Pino 6 | GND — Ground |
| Pino 7 | I/O — User I/O pin |
| Pino 8 | I/O — User I/O pin |
| Pino 9 | I/O — User I/O pin |
| Pino 10 | I/O — User I/O pin |
| Pino 11 | I/O — User I/O pin |
| Pino 12 | GND — Ground |
| Pino 13 | I/O — User I/O pin |
| Pino 14 | I/O — User I/O pin |
| Pino 15 | TDI — JTAG Test Data In (dedicated) |
| Pino 16 | TMS — JTAG Test Mode Select (dedicated) |
| Pino 17 | TCK — JTAG Test Clock (dedicated) |
| Pino 18 | I/O — User I/O pin |
| Pino 19 | I/O — User I/O pin |
| Pino 20 | I/O — User I/O pin |
| Pino 21 | VCCINT — Core supply, 3.3 V |
| Pino 22 | GLOBAL CLK — Global clock input (dedicated) |
| Pino 23 | I/O — User I/O pin |
| Pino 24 | I/O — User I/O pin |
| Pino 25 | I/O — User I/O pin |
| Pino 26 | I/O — User I/O pin |
| Pino 27 | GND — Ground |
| Pino 28 | I/O — User I/O pin |
| Pino 29 | I/O — User I/O pin |
| Pino 30 | I/O — User I/O pin |
| Pino 31 | I/O — User I/O pin |
| Pino 32 | I/O — User I/O pin |
| Pino 33 | VCCIO — I/O supply, 2.5 V or 3.3 V |
| Pino 34 | I/O — User I/O pin |
| Pino 35 | I/O — User I/O pin |
| Pino 36 | I/O — User I/O pin |
| Pino 37 | I/O — User I/O pin |
| Pino 38 | I/O — User I/O pin |
| Pino 39 | GLOBAL CLR — Global clear input (dedicated) |
| Pino 40 | I/O — User I/O pin |
| Pino 41 | I/O — User I/O pin |
| Pino 42 | TDO — JTAG Test Data Out (dedicated) |
| Pino 43 | I/O — User I/O pin |
| Pino 44 | I/O — User I/O pin |
Aplicações típicas
EPM3064ATC44-4N é adequado para 6 aplicaçãos: Bus Decoding and Address Mapping, Asynchronous State Machine Controller, Microcontroller I/O Expansion and Glue Logic, Mixed-Voltage Level Translation Interface, Legacy 5-V System Modernization, Peripheral Chip-Select and Wait-State Generator.
Bus Decoding and Address Mapping
The EPM3064ATC44-4N fits bus-decoding and address-mapping tasks because its 64 macrocells and 34 I/Os can decode wide address or chip-select fan-out in a single non-volatile device, while its 4.5 ns tpd / 222.2 MHz fCNT comfortably meets typical memory and peripheral access windows. It is used between a microcontroller/microprocessor and a bank of peripherals (SRAM, Flash, glue logic), where the CPLD generates chip-select enables and handles wait-state insertion. The 3.3-V core with selectable 2.5-V/3.3-V VCCIO makes it easy to interface to legacy 5-V-tolerant buses via external resistors, and JTAG ISP lets engineers iterate on the address table without removing the part. Power-on is instant because the configuration is held in on-chip EEPROM.
Recomendado
Asynchronous State Machine Controller
The EPM3064ATC44-4N fits asynchronous state-machine designs because its deterministic interconnect (Altera Interconnect Matrix) gives predictable, placement-independent timing - critical for asynchronous interfaces where races must be avoided. With 64 macrocells and a 4.5 ns tpd, it can implement multi-state control sequences for industrial sequencers, motor-control logic, or test-equipment state graphs. The EEPROM-based architecture means the state machine definition is retained across power cycles without external boot memory, and the JTAG interface supports on-board debug and revision updates. Compared with an FPGA, the part offers faster power-on and a smaller bill of materials for moderate-complexity control logic.
Recomendado
Microcontroller I/O Expansion and Glue Logic
The EPM3064ATC44-4N fits microcontroller I/O-expansion roles because it can multiplex extra GPIOs, generate PWM waveforms, debounce inputs, and drive indicator LEDs from a single 44-pin TQFP. Its 34 user I/Os and 4 dedicated inputs provide headroom over typical MCU pin counts, while the 3.3-V VCCINT with 5-V-tolerant inputs allows direct connection to 5-V MCU buses without level shifters. The MAX 3000A family's instant-on (no boot time) and JTAG ISP make it convenient for prototyping - engineers can iterate on the logic without re-spinning the PCB. It is widely used in consumer appliances and industrial controllers where deterministic response is more important than raw logic density.
Recomendado
Mixed-Voltage Level Translation Interface
The EPM3064ATC44-4N fits mixed-voltage interface-bridging applications because of its 5.0-V-tolerant inputs and selectable 2.5-V/3.3-V VCCIO outputs per the MAX 3000A datasheet. It can sit between a 5-V microcontroller and a 3.3-V peripheral bus (or between a 3.3-V MCU and 2.5-V legacy logic), translating control signals while optionally performing protocol conversion. The 4.5 ns tpd preserves timing margins for SPI, I2C, and UART bridging, and 34 I/Os are sufficient for full bus replication. This avoids dedicated level-shifter ICs when protocol logic must also be implemented, consolidating the BOM.
Recomendado
Legacy 5-V System Modernization
The EPM3064ATC44-4N fits legacy 5-V-system modernization because of its 5.0-V-tolerant CMOS inputs and JTAG in-system programmability per the manufacturer datasheet. Engineers retrofitting older equipment can drop the part onto an existing 5-V bus (with input current-limit resistors as needed) to add new glue functions, monitoring, or diagnostic logic without redesigning the supply rails. The instant-on EEPROM configuration avoids boot latency, important in retrofits where predictable startup matters. Its commercial 0C to +70C range covers most indoor retrofit scenarios, and the 44-pin TQFP is hand-solderable for low-volume rebuilds.
Recomendado
Peripheral Chip-Select and Wait-State Generator
The EPM3064ATC44-4N fits peripheral chip-select and wait-state generation because of its combination of 64 macrocells, 4.5 ns tpd, and the deterministic AIM interconnect per the MAX 3000A datasheet. It generates properly-timed chip-select pulses and wait-state insertions for SRAM, NOR Flash, and legacy peripherals sharing a parallel bus with a modern processor. The non-volatile EEPROM configuration means the wait-state map persists without a boot ROM, simplifying firmware bring-up. With 34 user I/Os, the device can fan out to multiple peripherals while still leaving pins for JTAG and global clocks for ongoing development.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPM3064ATC44-4N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPM3064ATC44-7N | EPM3064ATC44-10N | EPM3032ATC44-4N | EPM3064ALC44-4N |
|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera |
| Package | 44-pin TQFP | 44-pin TQFP - same | 44-pin TQFP - same | 44-pin TQFP - same | 44-pin TQFP - same |
| Macro Cells | 64 | 64 | 64 | 32 | 64 |
| User I/Os | 34 | 34 | 34 | 34 | 34 |
| Propagation Delay (tpd) | 4.5 ns | 7.5 ns | 10 ns | 4.5 ns | 4.5 ns |
| Max Counter Frequency | 222.2 MHz | ~152 MHz | ~116 MHz | 222.2 MHz | 222.2 MHz |
| Usable Gates | 1,250 | 1,250 | 1,250 | 600 | 1,250 |
| VCCIO Flexibility | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V |
| JTAG ISP | Yes (IEEE 1149.1 / 1532) | Yes | Yes | Yes | Yes |
Principais diferenciais
- Fastest speed grade in the 44-pin TQFP MAX 3000A pinout (vs EPM3064ATC44-7N)
- Twice the logic density of the smaller MAX 3000A 44-pin TQFP variant (vs EPM3032ATC44-4N)
- Standard power grade with full speed support (vs EPM3064ALC44-4N)
Notas de projeto
Per the MAX 3000A datasheet, the EPM3064ATC44-4N requires a 3.3-V VCCINT supply and a separate VCCIO rail that can be tied to 2.5 V or 3.3 V depending on output logic levels. Decouple VCCINT with a 0.1 uF ceramic capacitor placed as close to the pin as possible, and add a bulk 10 uF capacitor on the supply rail. The device is 5.0-V-tolerant on inputs, but outputs must never exceed their VCCIO rail. Estimated: ICCINT typical is around 30-50 mA for a fully utilized EPM3064ATC44 design; confirm with the datasheet ICC vs frequency graph for your specific design.
Route the JTAG chain (TDI, TDO, TMS, TCK) as a clean daisy-chain from the connector to the device with stubs kept under 100 mil and a 10 kohm pull-up on TCK and TMS. Place the CPLD near the connectors it serves to minimize bus-stub length, especially for memory interfaces. The 44-pin TQFP has a 0.8 mm pitch - use 0.4 mm-wide traces between pads and at least 0.2 mm clearance to avoid solder-bridge defects at assembly.
Do not confuse the -4 speed grade with the -7 or -10 grades - the -4 is the fastest 44-pin TQFP variant (4.5 ns tpd, 222.2 MHz fCNT), so substituting a -7 or -10 in a -4 design will reduce timing margin. Also note that the EPM3064ATC44-4N is in NRND (Not Recommended for New Designs) status - for new designs, evaluate the MAX II family (e.g., EPM240T100C5N) which offers higher density, lower power, and active lifecycle support, although at the cost of a different package and pinout.
Keep the VCCINT and VCCIO planes continuous under the device and stitch grounds around the TQFP with at least one via per paddle-adjacent ground pin. JTAG signals should be length-matched within the chain. If you use the device for high-speed bus decoding, place series 33 ohm damping resistors on outputs that drive long board traces to control ringing - the 4.5 ns edge rate is fast enough to excite transmission-line effects on traces longer than ~2 inches.
Informações de conformidade
RoHS and REACH status were not present in the verified web data - marker added in specs[]; AEC-Q100 is not applicable because the EPM3064ATC44-4N is a commercial-grade (0C to +70C) part. Lead-free is typical for Altera MAX 3000A devices but should be confirmed against the manufacturer's material declaration.