ISL8394IBZ - 4-Channel SPDT Analog Switch | Renesas Electronics
N.º da peça: ISL8394IBZ ✓ AtivoISL8394IBZ Visão geral
An analog switch is a semiconductor interface that routes analog or digital signals between circuit nodes under digital control. The ISL8394 belongs to the broader analog switch and multiplexer hierarchy, which includes SPDT switches, multiplexers, demultiplexers, and interface ICs used in test, measurement, communications, and instrumentation systems. Its quad SPDT arrangement allows one source signal to be connected to either of two destinations for each channel, or two sources to be routed to a common output, depending on the application configuration.
According to the manufacturer datasheet, the ISL8394 operates from a single +2 V to +12 V supply or from a dual supply of +/−2 V to +/−6 V. The device is specified for low power consumption of 5 microwatts, maximum leakage current of 2.5 nA, and fast switching speeds. The supplied product information identifies the device as a 4-circuit, 2:1 analog switch with 35 ohm on-resistance in a 20-SOIC package. These characteristics suit battery-powered equipment and precision measurement circuits where signal integrity and low standby current are important.
Typical uses include battery-powered test equipment, data-acquisition systems, audio and communication signal routing, instrumentation interfaces, and compact embedded measurement products. In a two-channel routing arrangement, control logic can select one of two analog inputs for connection to a shared signal-processing block while the other inputs remain electrically isolated.
Designers should pay close attention to the control logic levels, supply sequencing, input voltage range, and signal amplitude at each switched node. The low-leakage and low-power characteristics make the ISL8394 useful in battery-powered systems, but the PCB should minimize parasitic capacitance around high-impedance nodes and provide clean return paths for control and supply pins.
This page combines the manufacturer datasheet details, distributor identification, package information, and practical design guidance to support component selection, replacement planning, and PCB implementation. It also distinguishes the core ISL8394 function from nearby comparator and multiplexer families, helping engineers determine when the quad SPDT architecture is the correct switching choice.
Alternativas drop-in para ISL8394IBZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ISL8394IBZ (mesmo formato e footprint) — diferindo em Package.
ISL83483IBZ-T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ISL83485IBZ-T
✅ Drop-InConsulte o preço
Ver ficha técnica →ISL8394IBZ Classificações máximas e características elétricas
| Product Type | Quad SPDT analog switch |
| Number of Circuits | 4 circuits |
| Multiplex Configuration | 2:1 |
| On-Resistance | 35 ohm |
| Supply Voltage, Single | +2 V to +12 V |
| Supply Voltage, Dual | +/-2 V to +/-6 V |
| Power Consumption | 5 microwatts |
| Maximum Leakage Current | 2.5 nA |
| Encapsulamento | 20-SOIC |
| Package Pin Count | 20 pins |
| Signal Type | Analog signal switching |
| Application Category | Battery-powered equipment |
| Tipo de montagem | Surface mount |
| Status do ciclo de vida | Active; current lifecycle confirmation requires manufacturer product status |
Guia de Configuração de Pinos do ISL8394IBZ 20 pins
Configuração de pinos para ISL8394IBZ (pacote 20 pins). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ISL8394IBZ.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ISL8394IBZ é adequado para 6 aplicaçãos: Battery-Powered Measurement Equipment, Data-Acquisition Signal Routing, Audio Signal Routing, Test and Instrumentation Interfaces, Communications Equipment Signal Isolation, Low-Power Embedded Control Interface.
Battery-Powered Measurement Equipment
The ISL8394IBZ fits battery-powered measurement equipment because the Intersil datasheet specifies 5 microwatts of power consumption and 2.5 nA maximum leakage current. Use the four SPDT channels to route low-level analog signals between a sensor interface and measurement circuitry. The single-supply range of +2 V to +12 V supports portable systems where standby power and leakage into the source are important. Keep the analog paths short, provide a defined ground reference, and verify the control levels against the selected supply voltage.
Recomendado
Data-Acquisition Signal Routing
The ISL8394IBZ can route multiple analog channels in a data-acquisition front end through its four independently controlled SPDT sections. Each switch supports a 2:1 arrangement, allowing a selected source to connect to a common processing path or two sources to be separated according to the wiring configuration. The 35 ohm on-resistance and low leakage are useful for preserving signal integrity in compact acquisition systems. Confirm the maximum signal bandwidth, charge injection, and off-isolation limits in the manufacturer datasheet before selecting the routing topology.
Recomendado
Audio Signal Routing
The ISL8394IBZ is appropriate for low-voltage audio signal routing where the design needs bidirectional or source-selection paths rather than a powered audio amplifier. The low-leakage characteristic helps isolate inactive channels, while the quad SPDT structure provides four routing decisions in a single 20-SOIC package. A single +2 V to +12 V supply simplifies portable audio circuitry. Keep the switched node traces compact, use a continuous ground plane, and verify that the selected signal amplitude remains below the device’s analog operating limits.
Recomendado
Test and Instrumentation Interfaces
The ISL8394IBZ can provide selectable signal paths in test and instrumentation systems where four SPDT switches are needed to connect sources, loads, or reference nodes. The 5 microwatt power consumption and 2.5 nA maximum leakage are favorable for low-power test fixtures and portable instruments. The 20-SOIC package supports conventional surface-mount assembly. Place the device close to connector or sensor routing, maintain a low-impedance supply return, and use the datasheet timing curves when defining settling requirements after a control change.
Recomendado
Communications Equipment Signal Isolation
The ISL8394IBZ can isolate and reroute low-level communications signals in compact equipment using four independent SPDT switches. Its low off-state leakage helps reduce unwanted coupling between channels, and the single-supply operation supports systems with a +2 V to +12 V rail. The device is appropriate when the signal path must be switched rather than amplified. Validate insertion loss, bandwidth, and off-isolation against the operating frequency, and keep high-speed routing away from noisy control and power-return paths.
Recomendado
Low-Power Embedded Control Interface
The ISL8394IBZ fits embedded control boards that need local analog routing without the higher power and leakage of a larger switching subsystem. Four SPDT channels can connect sensors, actuators, or test points under MCU control while the device operates from a low single supply. The 20-SOIC package is suitable for standard surface-mount layouts and the 5 microwatt power specification supports low-power operation. Confirm logic thresholds, supply ramp requirements, and absolute maximum voltages in the manufacturer datasheet.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ISL8394IBZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ISL83483IBZ-T | ISL83485IBZ | MAX394EPP+ |
|---|---|---|---|---|
| Package | 20-SOIC | 20-SOIC; exact package drawing requires confirmation | 20-SOIC; exact package drawing requires confirmation | 20-pin DIP; not the same package |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Maxim Integrated |
Principais diferenciais
- Quad SPDT routing in one 20-SOIC package (vs MAX394EPP+)
- Low-voltage single-supply operation (vs MAX394EPP+)
- Low power and leakage characteristics (vs ISL83483IBZ-T)
Notas de projeto
Place the ISL8394IBZ close to the analog nodes being routed. Keep switched traces short, provide a continuous ground reference, and separate sensitive analog paths from digital control and switching-current returns. The 20-SOIC footprint should be checked against the exact manufacturer pin drawing before routing. Do not rely on package-name similarity alone when assigning the control and supply pins.
Operate the device only within its specified single-supply range of +2 V to +12 V or dual-supply range of +/−2 V to +/−6 V. Ensure the supply rails remain within the absolute maximum limits and provide adequate decoupling near the device. Because the datasheet specifies only 5 microwatts of power consumption, carefully evaluate control-state leakage and unused-channel behavior as part of the complete system power budget.
Do not assume that a related ISL8348x MPN has identical pinout or switching behavior. Verify the SOIC pin table, control thresholds, on-resistance, leakage, switching time, and absolute maximum ratings for each candidate. Similarly, the MAX394EPP+ uses a DIP package according to the comparison information, so it is not a same-footprint replacement without PCB redesign.
For high-impedance sources, minimize parasitic capacitance around the switched nodes and avoid routing control lines adjacent to sensitive analog inputs. Confirm the device’s off-isolation and charge-injection characteristics against the required measurement accuracy. Use the manufacturer timing curves to establish settling time after a control transition rather than estimating it from general switching speed.
Informações de conformidade
The available product information identifies the component and its analog-switch function but does not provide definitive compliance statements for the exact ISL8394IBZ configuration.