ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas
N.º da peça: ISL8490IB-T ✓ AtivoISL8490IB-T Visão geral
A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives differential signals back into logic-level outputs. RS-485 supports multipoint, half-duplex buses and is widely used in industrial automation, while RS-422 supports point-to-point and multidrop balanced links. The ISL8490IB-T belongs to the interface-IC hierarchy as a physical-layer communication device between a host controller and a balanced physical layer.
The principal device characteristics include a 5 V supply, a 1/1 driver-to-receiver configuration, full RS-422 and RS-485 operation, low power consumption, and either high-speed or slew-rate-limited performance. These features make the device useful when a compact interface must support balanced differential signaling in a small PCB footprint. Its 8-pin SOIC construction also simplifies assembly and inspection on both through-hole-compatible boards and mixed-technology assemblies.
BiCMOS implementation combines bipolar and CMOS characteristics within the interface circuit. In this transceiver family, that architecture supports low-power operation while preserving the drive and receive performance needed for balanced communication links. The manufacturer describes the ISL8490 series as devices specified for operation across a 10% supply variation around 5 V, allowing design attention to remain focused on interface margins and system-level power behavior.
Typical uses include industrial sensor buses, factory automation equipment, process-control interfaces, building-control networks, and communications ports that connect a UART or controller to an RS-485 or RS-422 cable. In half-duplex RS-485 systems, driver-enable control can determine the bus direction. In full-duplex RS-422 systems, the driver and receiver can remain active without contention because the two channels use separate differential pairs.
PCB design should preserve the symmetry of each differential pair, provide a continuous ground reference, and route the balanced lines away from clocks, switching nodes, and other high-current paths. Decoupling capacitors should be placed close to the supply and ground pins. External termination and biasing remain application-dependent and should be configured from the cable length, topology, node count, and driver state rather than added indiscriminately.
This product overview combines the device identity, RS-485/RS-422 application context, package information, and practical implementation guidance. It is designed to help engineers identify the correct transceiver function and plan a robust balanced-communication layout without conflating protocol requirements, termination practice, and device-level capabilities.
Alternativas drop-in para ISL8490IB-T — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ISL8490IB-T (mesmo formato e footprint) — diferindo em Package, Power Class, Signal Type, Supply Voltage, Supported Standards.
ISL8490IB
✅ Drop-InConsulte o preço
Ver ficha técnica →ISL8490IBZ-T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ISL8490IB-T Especificações
| Product Type | RS-485/RS-422 single transceiver |
| Tensão de alimentação | 5 V nominal |
| Supply Tolerance | 10% of 5 V nominal |
| Driver-to-Receiver Configuration | 1/1 |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Supported Standards | RS-422 and RS-485 |
| Logic Family | BiCMOS |
| Power Class | Low-power interface |
| Signal Mode | High-speed or slew-rate-limited |
| Signal Type | Balanced differential |
| Encapsulamento | 8-pin SOIC |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Surface mount |
| Termination | External, application dependent |
Guia de Configuração de Pinos do ISL8490IB-T 8-pin soic
Configuração de pinos para ISL8490IB-T (pacote 8-pin soic). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para ISL8490IB-T.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ISL8490IB-T é adequado para 6 aplicaçãos: Industrial Sensor Bus, Factory Automation Controller, Process-Control Instrumentation, Building Control Network, Remote Telemetry Link, Data Acquisition Unit.
Industrial Sensor Bus
The ISL8490IB-T fits a 5 V industrial sensor bus by providing one balanced driver and one balanced receiver in an 8-pin SOIC package. Connect the transceiver to a controller UART and route the RS-485 differential pair toward remote sensors. Balanced signaling reduces susceptibility to common-mode noise compared with a single-ended interface, while the family’s high-speed or slew-rate-limited operating modes allow the bus rate to be matched to the cable length and transceiver configuration. The PCB should preserve differential-pair symmetry, maintain a continuous ground reference, and use termination only at the designated physical endpoints of the trunk.
Recomendado
Factory Automation Controller
The ISL8490IB-T is suitable for connecting a factory automation controller to field equipment over RS-485 or RS-422. Its single driver and receiver support a compact transceiver position near the controller, while the 5 V supply aligns with many embedded control platforms. The interface can serve a multidrop RS-485 segment or a balanced point-to-point link, depending on enable logic and cable topology. Engineers should assess data rate against cable length, keep the differential route away from motor and relay paths, and provide surge or ESD protection when the port connects to external field wiring.
Recomendado
Process-Control Instrumentation
The ISL8490IB-T can connect process-control instrumentation to a supervisory controller using balanced RS-485 or RS-422 signaling. The 1/1 transceiver arrangement allows a node to transmit commands or measurements and receive acknowledgements through separate logical directions, subject to the bus-enable strategy. Its low-power BiCMOS implementation suits compact measurement equipment, while the 8-pin SOIC package simplifies board assembly. For instrumentation cabinets, use a defined grounding strategy, protect the connector against transients, and validate the communication rate over the intended cable length before freezing the PCB layout.
Recomendado
Building Control Network
The ISL8490IB-T is appropriate for a low-power building-control node that links a controller to a balanced RS-485 supervisory bus. One transceiver channel can support command transmission and status reception without requiring two separate interface packages, while its 8-pin SOIC footprint helps maintain a compact control-panel design. Use the slew-rate-limited operating mode when the cable network requires reduced edge rates for EMC control. Keep the differential pair routed as a controlled pair, establish termination according to the topology, and ensure connector protection matches the building wiring environment.
Recomendado
Remote Telemetry Link
The ISL8490IB-T supports a compact remote-telemetry node when the link requires a 5 V RS-485 or RS-422 physical interface. The single driver and receiver provide the basic communication channel between a telemetry controller and a remote station while keeping the device count low. Differential signaling is useful where the source and destination share a large ground-potential range or face coupled industrial noise. The designer should select the operating mode and cable rate together, provide biasing so the bus remains in a defined idle state, and include transient protection when the telemetry cable leaves the enclosure.
Recomendado
Data Acquisition Unit
The ISL8490IB-T can terminate a balanced communication channel in a compact data-acquisition unit. One driver and one receiver are sufficient for a point-to-point or multidrop data path linking an acquisition controller to remote sensors or another data module. The low-power 5 V BiCMOS design supports space-constrained equipment, and the 8-pin SOIC package is compatible with automated assembly. Preserve continuous return-current paths beneath the differential pair, separate the interface from switching regulators and relays, and select termination and bias components only after the complete bus topology and idle state are defined.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ISL8490IB-T — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ISL8490IB | ISL8490IBZ-T |
|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Transceiver Configuration | 1/1 | 1/1 | 1/1 |
| Supply Voltage | 5 V nominal | 5 V nominal | 5 V nominal |
| Supported Standards | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 |
| Logic Technology | BiCMOS | BiCMOS | BiCMOS |
| Operating Mode | High-speed or slew-rate-limited | High-speed or slew-rate-limited | High-speed or slew-rate-limited |
| Signal Type | Balanced differential | Balanced differential | Balanced differential |
Principais diferenciais
- Combines a balanced driver and receiver in a compact package (vs ISL8490IB)
- Supports high-speed and slew-rate-limited signaling in one family (vs ISL8490IBZ-T)
- Single-interface solution for compact balanced-communication boards (vs ISL8490IB)
Notas de projeto
Route each RS-485 or RS-422 differential pair as a tightly coupled pair over a continuous reference plane. Match the spacing of both conductors, minimize stubs, and avoid changing layer reference mid-route. Keep the pair away from switching-node copper, relays, inductors, and high-current return paths. The driver and receiver connections should enter the transceiver on adjacent pins where the package assignment permits, reducing loop area and improving common-mode noise immunity.
Do not place termination resistors at every node. For a conventional RS-485 trunk, termination belongs at the two physical ends, and its value should be chosen from the cable impedance and driver topology. RS-422 commonly uses termination at the receiver end of each pair. Biasing serves a different function from termination and must be placed so that an idle bus has a valid differential state without materially loading the network.
Place the local supply-decoupling capacitor immediately across the transceiver's supply and ground pins, with a short, low-inductance connection. Keep the return current within the same quiet region rather than routing it through a distant chassis-ground path. Because the device is specified around 5 V, verify the actual rail at the IC under minimum input voltage and maximum transceiver activity; avoid sharing the connection with noisy actuator or switching-supply return current.
Choose between the high-speed and slew-rate-limited operating modes with the complete installation in mind. Faster edge rates can improve throughput but generally place greater requirements on cable impedance, topology, layout, and radiated-emission control. Slower slew-rate operation can reduce EMI and ringing on longer or less controlled interconnects. Validate the selected mode with the intended cable, connector, grounding arrangement, and neighboring switching circuitry.
Do not substitute the ISL8490IB, ISL8490IBZ-T, or another family member solely from the eight-pin outline. The electrical function may appear identical, but the ordering suffix may encode temperature grade, lead finish, packing, or qualification status. Compare the approved part number, absolute maximum ratings, operating-temperature range, and package drawing before treating any related listing as a drop-in production replacement.
Informações de conformidade
The exact ordering-code compliance attributes are not stated in the product information. Confirm environmental declarations and automotive qualification status with Renesas before release.