Renesas Electronics

ISL8490IB-T - 5V RS-485/RS-422 Transceiver | Renesas

부품 번호: ISL8490IB-T ✓ 활성
5 V nominal Vdss RS-422 and RS-485 Rds(on) 8-pin SOIC Package
MOQ: 1 |

ISL8490IB-T 개요

The Renesas Electronics ISL8490IB-T is a 5 V, single-channel RS-485/RS-422 transceiver built with BiCMOS technology and supplied in an 8-pin SOIC package. It combines one driver and one receiver in one package, supports both RS-485 and RS-422 balanced communication, and provides a low-power interface for industrial and instrumentation links. The device is designed for applications requiring either high-speed operation or slew-rate-limited signaling.

A differential line transceiver is an interface IC that converts logic-level signals into balanced differential signals and receives differential signals back into logic-level outputs. RS-485 supports multipoint, half-duplex buses and is widely used in industrial automation, while RS-422 supports point-to-point and multidrop balanced links. The ISL8490IB-T belongs to the interface-IC hierarchy as a physical-layer communication device between a host controller and a balanced physical layer.

The principal device characteristics include a 5 V supply, a 1/1 driver-to-receiver configuration, full RS-422 and RS-485 operation, low power consumption, and either high-speed or slew-rate-limited performance. These features make the device useful when a compact interface must support balanced differential signaling in a small PCB footprint. Its 8-pin SOIC construction also simplifies assembly and inspection on both through-hole-compatible boards and mixed-technology assemblies.

BiCMOS implementation combines bipolar and CMOS characteristics within the interface circuit. In this transceiver family, that architecture supports low-power operation while preserving the drive and receive performance needed for balanced communication links. The manufacturer describes the ISL8490 series as devices specified for operation across a 10% supply variation around 5 V, allowing design attention to remain focused on interface margins and system-level power behavior.

Typical uses include industrial sensor buses, factory automation equipment, process-control interfaces, building-control networks, and communications ports that connect a UART or controller to an RS-485 or RS-422 cable. In half-duplex RS-485 systems, driver-enable control can determine the bus direction. In full-duplex RS-422 systems, the driver and receiver can remain active without contention because the two channels use separate differential pairs.

PCB design should preserve the symmetry of each differential pair, provide a continuous ground reference, and route the balanced lines away from clocks, switching nodes, and other high-current paths. Decoupling capacitors should be placed close to the supply and ground pins. External termination and biasing remain application-dependent and should be configured from the cable length, topology, node count, and driver state rather than added indiscriminately.

This product overview combines the device identity, RS-485/RS-422 application context, package information, and practical implementation guidance. It is designed to help engineers identify the correct transceiver function and plan a robust balanced-communication layout without conflating protocol requirements, termination practice, and device-level capabilities.

드롭인 대체품: ISL8490IB-T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: ISL8490IB-T (동일 폼 팩터 및 풋프린트) — 차이점: Package, Power Class, Signal Type, Supply Voltage, Supported Standards.

Renesas Electronics
Package: 8-SOIC (0.154 in, 3.90 mm width)
Power Class: Low power
Signal Type: Differential balanced signaling
비교 대상: ISL8490IB-T →

ISL8490IB

✅ 드롭인
Renesas Electronics
📦 8-SOIC
5 V · RS-485 and RS-422 · Single transceiver · Low power · High speed or slew-rate limited · Differential balanced signaling · 8-SOIC (0.154 in, 3.90 mm width) · 8 pins

가격 문의

데이터시트 보기 →

ISL8490IBZ-T

✅ 드롭인
📦 8-SOIC
The related listing specifies the same 5 V single RS-485/RS-422 transceiver in 8-SOIC, while the Z suffix indicates an ordering-code difference from the target that must be checked for qualification.

📋 참조 대체품 (카탈로그에 없음)

ISL8490IB-T 사양

Product Type RS-485/RS-422 single transceiver
공급 전압 5 V nominal
Supply Tolerance 10% of 5 V nominal
Driver-to-Receiver Configuration 1/1
Driver Count 1 driver
Receiver Count 1 receiver
Supported Standards RS-422 and RS-485
Logic Family BiCMOS
Power Class Low-power interface
Signal Mode High-speed or slew-rate-limited
Signal Type Balanced differential
패키지 8-pin SOIC
핀 수 8 pins
실장 유형 Surface mount
Termination External, application dependent

ISL8490IB-T 8-pin soic 핀 구성 가이드

ISL8490IB-T(8-pin soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

ISL8490IB-T의 8-pin soic 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: ISL8490IB-T.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

ISL8490IB-T 적합 용도: 6 애플리케이션s: Industrial Sensor Bus, Factory Automation Controller, Process-Control Instrumentation, Building Control Network, Remote Telemetry Link, Data Acquisition Unit.

🏭

Industrial Sensor Bus

The ISL8490IB-T fits a 5 V industrial sensor bus by providing one balanced driver and one balanced receiver in an 8-pin SOIC package. Connect the transceiver to a controller UART and route the RS-485 differential pair toward remote sensors. Balanced signaling reduces susceptibility to common-mode noise compared with a single-ended interface, while the family’s high-speed or slew-rate-limited operating modes allow the bus rate to be matched to the cable length and transceiver configuration. The PCB should preserve differential-pair symmetry, maintain a continuous ground reference, and use termination only at the designated physical endpoints of the trunk.

🏭

Factory Automation Controller

The ISL8490IB-T is suitable for connecting a factory automation controller to field equipment over RS-485 or RS-422. Its single driver and receiver support a compact transceiver position near the controller, while the 5 V supply aligns with many embedded control platforms. The interface can serve a multidrop RS-485 segment or a balanced point-to-point link, depending on enable logic and cable topology. Engineers should assess data rate against cable length, keep the differential route away from motor and relay paths, and provide surge or ESD protection when the port connects to external field wiring.

🔧

Process-Control Instrumentation

The ISL8490IB-T can connect process-control instrumentation to a supervisory controller using balanced RS-485 or RS-422 signaling. The 1/1 transceiver arrangement allows a node to transmit commands or measurements and receive acknowledgements through separate logical directions, subject to the bus-enable strategy. Its low-power BiCMOS implementation suits compact measurement equipment, while the 8-pin SOIC package simplifies board assembly. For instrumentation cabinets, use a defined grounding strategy, protect the connector against transients, and validate the communication rate over the intended cable length before freezing the PCB layout.

🧩

Building Control Network

The ISL8490IB-T is appropriate for a low-power building-control node that links a controller to a balanced RS-485 supervisory bus. One transceiver channel can support command transmission and status reception without requiring two separate interface packages, while its 8-pin SOIC footprint helps maintain a compact control-panel design. Use the slew-rate-limited operating mode when the cable network requires reduced edge rates for EMC control. Keep the differential pair routed as a controlled pair, establish termination according to the topology, and ensure connector protection matches the building wiring environment.

🌐

Remote Telemetry Link

The ISL8490IB-T supports a compact remote-telemetry node when the link requires a 5 V RS-485 or RS-422 physical interface. The single driver and receiver provide the basic communication channel between a telemetry controller and a remote station while keeping the device count low. Differential signaling is useful where the source and destination share a large ground-potential range or face coupled industrial noise. The designer should select the operating mode and cable rate together, provide biasing so the bus remains in a defined idle state, and include transient protection when the telemetry cable leaves the enclosure.

📡

Data Acquisition Unit

The ISL8490IB-T can terminate a balanced communication channel in a compact data-acquisition unit. One driver and one receiver are sufficient for a point-to-point or multidrop data path linking an acquisition controller to remote sensors or another data module. The low-power 5 V BiCMOS design supports space-constrained equipment, and the 8-pin SOIC package is compatible with automated assembly. Preserve continuous return-current paths beneath the differential pair, separate the interface from switching regulators and relays, and select termination and bias components only after the complete bus topology and idle state are defined.

What is the ISL8490IB-T?
The ISL8490IB-T is a 5 V, low-power, 1/1 RS-485/RS-422 transceiver from Renesas Electronics. It combines one driver and one receiver in an 8-pin SOIC package and supports balanced differential communication using BiCMOS circuitry. According to the manufacturer datasheet, the family can be used in high-speed or slew-rate-limited applications, making it appropriate for industrial control, instrumentation, and other balanced bus systems.
Is the ISL8490IB-T a full-duplex RS-485 transceiver?
The ISL8490IB-T is primarily a combined RS-485/RS-422 transceiver with one driver and one receiver, not a dedicated full-duplex RS-485 product with separate transmit and receive channels. In an RS-485 bus, direction is normally managed with a driver-enable signal, whereas the same device can support point-to-point or multidrop RS-422 links when the channel assignment matches the circuit. Consult the manufacturer pin and enable-function description before assigning bus direction.
What is the supply voltage of the ISL8490IB-T?
The ISL8490IB-T operates from a nominal 5 V supply. The Intersil family description states that the devices are specified for a 10% supply variation around 5 V, corresponding to an allowable nominal operating span of approximately 4.5 V to 5.5 V. This range should be checked against the complete manufacturer datasheet when designing the supply rail, especially when the transceiver shares a board with higher-voltage circuitry.
Where can I download the ISL8490IB-T datasheet PDF?
The ISL8490IB-T datasheet is available through the linked Intersil/Renesas datasheet page, which identifies the ISL8490 family as 5 V, low-power, high-speed or slew-rate-limited RS-485/RS-422 transceivers. Use the manufacturer pin-description table, electrical characteristics, and application information when assigning connector signals or confirming a specific operating condition. The target ordering code is ISL8490IB-T in an 8-pin SOIC package.
Where is the pinout for ISL8490IB-T?
The ISL8490IB-T uses an 8-pin SOIC package and should be assigned from the exact pin-description table in the manufacturer datasheet. The function assignments typically distinguish supply, ground, driver input and enable, driver outputs, receiver input, and receiver output, but pin numbers must not be inferred from a generic transceiver because enable and receiver-output variants can differ. Use the package drawing together with the ISL8490 family datasheet when laying out the PCB.
What can replace the ISL8490IB-T?
The closest documented alternatives in the ISL8490 family are ISL8490IB and ISL8490IBZ-T, both listed as 8-pin SOIC RS-485/RS-422 transceivers. They can be considered for footprint-compatible review, but ordering suffixes, temperature grade, packaging, and qualification markings must be checked against the original BOM requirements. No suitable cross-brand part with verified pin compatibility and equivalent electrical characteristics was established, so PCB changes should not be assumed.
IS the ISL8490IB-T the same as ISL8490IBZ-T?
The ISL8490IB-T and ISL8490IBZ-T are both presented as 8-pin SOIC single transceivers for RS-485/RS-422 balanced communication, but their ordering suffixes must not be assumed to represent identical commercial or qualification terms. ISL8490IBZ-T appears in the product listing as a related 5 V transceiver, while ISL8490IB-T is the exact target orderable. Verify lead finish, operating grade, packing, and lifecycle requirements before substitution.
ISL8490IB-T versus ISL8490IB: which should be selected?
ISL8490IB-T is the exact target ordering code and is listed as an 8-SOIC RS-485/RS-422 transceiver, while ISL8490IB is the corresponding non-“-T” listing. The family description associates these devices with the same 5 V BiCMOS single-transceiver function. Selection should be based on the approved supplier configuration, package orientation, temperature grade, and ordering-code definition rather than on the visible family resemblance alone.
When should I choose ISL8490IB-T over another RS-485 transceiver?
Choose the ISL8490IB-T when the design needs a compact 8-pin SOIC solution for 5 V RS-485 or RS-422 balanced signaling and the exact ordering code satisfies the environmental and sourcing requirements. It is particularly useful when a board must support one driver and one receiver in a small footprint. If the design requires two independent full-duplex channels, fail-safe behavior beyond the documented family features, or a package other than 8-pin SOIC, choose a transceiver explicitly specified for those requirements.
Is the ISL8490IB-T suitable for industrial automation and sensor networks?
The ISL8490IB-T is suitable for industrial automation and sensor-network interfaces when the cable topology, data rate, termination, and protection strategy are compatible with its RS-485/RS-422 ratings. Its low-power 5 V BiCMOS implementation supports compact controller boards and balanced links to remote sensors. Industrial use also requires checking the operating-temperature grade, surge protection, isolation requirements, grounding strategy, and applicable electromagnetic-compatibility requirements for the finished equipment.
How should termination and biasing be designed for ISL8490IB-T?
Termination and biasing for an ISL8490IB-T network should be established from the completed bus topology rather than copied from a generic reference circuit. RS-485 commonly places termination at the two physical ends of the trunk, while bias resistors establish the idle differential state at one suitable location. Avoid excessive termination when cables are short, and calculate the bias network against the receiver threshold and the number of enabled drivers before finalizing component values.
Does the ISL8490IB-T need external bus protection?
The ISL8490IB-T does not eliminate the need to assess external protection for a cable-connected RS-485 or RS-422 port. Long industrial cables can expose the interface to surge, ESD, and transient events, so the design should define whether the transceiver is directly connected or supplemented by external protection. The required network depends on cable length, grounding, installation environment, and equipment-level immunity requirements, and it should be reviewed against the complete interface specification.
What is the lead time for ISL8490IB-T?
The current lead time for ISL8490IB-T should be requested through the Request a Quote form on this page. A distributor listing indicates that the part is commercially offered, but it does not establish a fixed factory lead time, scheduled allocation, or shipment date for every order quantity. For production planning, state the required quantity, date code policy, permitted packaging, and target delivery date with the quotation request so current manufacturing conditions can be assessed.
Is ISL8490IB-T in stock and where can it be purchased?
The ISL8490IB-T is commercially listed and current stock should be confirmed through the Request a Quote form on this page. The form is the appropriate channel for checking exact MPN availability, quantity breaks, packaging, date-code requirements, and delivery timing. Do not treat a general product-page availability statement as a guarantee that a specific quantity is allocated for an incoming order.
What is the price of ISL8490IB-T?
The current commercial terms for ISL8490IB-T are available through the Request a Quote form on this page. Enter the required quantity and any date-code, trace, packaging, or delivery requirements so the quotation reflects the exact ordering code rather than a family-level representation. Pricing for this component can vary with quantity, supply status, and order conditions, so a static price figure should not be used for budgeting or purchase approval.

엔지니어링 참조 데이터: ISL8490IB-T — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose ISL8490IB-T when a compact 5 V board needs one balanced driver and one receiver for an RS-485 or RS-422 link, particularly in industrial sensor, automation, telemetry, or process-control equipment. Its BiCMOS implementation, selectable high-speed or slew-rate-limited operation, and 8-pin SOIC package make it appropriate when PCB area, assembly simplicity, and interface consolidation are priorities. Select ISL8490IB only after confirming that its ordering-code differences satisfy the approved temperature, packing, and qualification requirements. ISL8490IBZ-T is a closely related 8-SOIC option, but its Z suffix must also be checked against the product specification and supplier program. Choose a different transceiver if the design requires multiple full-duplex channels, isolation, integrated surge protection, a different package, or a data rate outside the ISL8490 family envelope. For any candidate, verify the complete pinout, enable behavior, electrical limits, and cable-side design rather than relying only on package similarity.

대체품과의 비교

파라미터 이 제품 ISL8490IB ISL8490IBZ-T
Package 8-SOIC 8-SOIC 8-SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Transceiver Configuration 1/1 1/1 1/1
Supply Voltage 5 V nominal 5 V nominal 5 V nominal
Supported Standards RS-422 and RS-485 RS-422 and RS-485 RS-422 and RS-485
Logic Technology BiCMOS BiCMOS BiCMOS
Operating Mode High-speed or slew-rate-limited High-speed or slew-rate-limited High-speed or slew-rate-limited
Signal Type Balanced differential Balanced differential Balanced differential

주요 차별점

  • Combines a balanced driver and receiver in a compact package (vs ISL8490IB)
  • Supports high-speed and slew-rate-limited signaling in one family (vs ISL8490IBZ-T)
  • Single-interface solution for compact balanced-communication boards (vs ISL8490IB)

설계 노트

Route each RS-485 or RS-422 differential pair as a tightly coupled pair over a continuous reference plane. Match the spacing of both conductors, minimize stubs, and avoid changing layer reference mid-route. Keep the pair away from switching-node copper, relays, inductors, and high-current return paths. The driver and receiver connections should enter the transceiver on adjacent pins where the package assignment permits, reducing loop area and improving common-mode noise immunity.

Do not place termination resistors at every node. For a conventional RS-485 trunk, termination belongs at the two physical ends, and its value should be chosen from the cable impedance and driver topology. RS-422 commonly uses termination at the receiver end of each pair. Biasing serves a different function from termination and must be placed so that an idle bus has a valid differential state without materially loading the network.

Place the local supply-decoupling capacitor immediately across the transceiver's supply and ground pins, with a short, low-inductance connection. Keep the return current within the same quiet region rather than routing it through a distant chassis-ground path. Because the device is specified around 5 V, verify the actual rail at the IC under minimum input voltage and maximum transceiver activity; avoid sharing the connection with noisy actuator or switching-supply return current.

Choose between the high-speed and slew-rate-limited operating modes with the complete installation in mind. Faster edge rates can improve throughput but generally place greater requirements on cable impedance, topology, layout, and radiated-emission control. Slower slew-rate operation can reduce EMI and ringing on longer or less controlled interconnects. Validate the selected mode with the intended cable, connector, grounding arrangement, and neighboring switching circuitry.

Do not substitute the ISL8490IB, ISL8490IBZ-T, or another family member solely from the eight-pin outline. The electrical function may appear identical, but the ordering suffix may encode temperature grade, lead finish, packing, or qualification status. Compare the approved part number, absolute maximum ratings, operating-temperature range, and package drawing before treating any related listing as a drop-in production replacement.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The exact ordering-code compliance attributes are not stated in the product information. Confirm environmental declarations and automotive qualification status with Renesas before release.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

ISL8490IB-T datasheet ISL8490IB-T pinout ISL8490IB-T datasheet pdf Renesas ISL8490IB-T ISL8490IB-T equivalent ISL8490IB-T replacement ISL8490IB-T cross reference ISL8490IB-T vs ISL8490IB ISL8490IB-T price ISL8490IB-T stock ISL8490IB-T footprint ISL8490IB-T application circuit

관련 부품 & 용어

Renesas Electronics ISL8490IB-T ISL8490IB ISL8490IBZ-T RS-485 RS-422 differential transceiver balanced differential signaling interface IC physical-layer interface BiCMOS 5 V transceiver 8-pin SOIC SOIC package family surface-mount package low-power transceiver slew-rate limiting industrial automation sensor network process control building control telemetry driver enable termination resistor biasing resistor
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기