KSZ8795CLXCC - 5-Port Managed Ethernet Switch | Microchip
N.º da peça: KSZ8795CLXCC ✓ AtivoKSZ8795CLXCC Visão geral
An Ethernet switch is a semiconductor that connects multiple physical-layer network ports to a common switching fabric and forwards Ethernet frames between ports and an uplink processor. The KSZ8795 operates at the Layer 2 data-link level, where frame destination addresses determine the outgoing port. Its managed architecture provides a practical platform for connected industrial, consumer, communications, and embedded equipment requiring several copper Ethernet connections.
The KSZ8795's principal features are its four dedicated 10/100 Mbps copper ports, dedicated 10/100/1000 Mbps uplink capability, and support for GMII/RGMII and MII/RMII processor interfaces. These parallel interface options let the switch connect to controllers with different clocking and data-width requirements. Layer 2 management supports controlled network behavior rather than operating solely as an unmanaged frame-forwarding device.
The KSZ8795CLXCC is packaged in an 80-lead LQFP, identified by the CLX package code in the manufacturer ordering information. Its 10 mm by 10 mm surface-mount package consolidates five-port switching, a Gigabit uplink, and management functions into one device. The exact pin names, voltage limits, timing limits, clock requirements, and electrical characteristics should be taken from the manufacturer datasheet and hardware design checklist when assigning PCB signals.
Typical implementations include industrial Ethernet gateways, IP cameras, building-automation controllers, communications equipment, set-top and media systems, and embedded products that expose several 10/100 ports while retaining a Gigabit connection to a host processor. The four fast ports support legacy 10/100 equipment, while the Gigabit uplink supports higher-bandwidth backhaul or processor traffic. MII, RMII, GMII, and RGMII connectivity allows the switch to be adapted to different embedded Ethernet controller arrangements.
PCB implementation requires careful separation of high-speed digital interfaces from copper-port circuitry. Place the KSZ8795CLX hardware design checklist alongside the datasheet, use the recommended magnetic-interface and termination network for each copper port, and observe the package's exposed-pad and thermal-land requirements. The manufacturer checklist specifies RJ45 transmit routing and a 75 ohm, 1000 pF, 2 kV capacitor network for the cable-side center tap, making those details important during layout review.
This page organizes the switch's port architecture, interface options, package information, sourcing workflow, and design references into an engineering-focused selection guide. It also identifies why the exact KSZ8795CLXCC ordering code must be reviewed against schematic, PCB, thermal, and firmware requirements rather than substituted solely by port count or headline uplink speed.
Alternativas drop-in para KSZ8795CLXCC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasKSZ8795CLXCC Classificações máximas e características elétricas
| Device Type | Layer 2-managed Ethernet switch |
| Total Port Count | 5 ports |
| 10/100 Mbps Copper Port Count | 4 ports |
| Gigabit Uplink Port Count | 1 port |
| Copper Port Speed | 10/100 Mbps |
| Gigabit Uplink Speed | 10/100/1000 Mbps |
| Processor Interface | GMII/RGMII and MII/RMII |
| Management Layer | Layer 2 |
| Package Type | 80-lead LQFP |
| Package Dimensions | 10 mm x 10 mm |
| Tipo de montagem | Surface mount |
| RJ45 Transmit Pair | RJ45 pins 3 and 6 |
| Cable-Side Center-Tap Termination | 75 ohm through 1000 pF, 2 kV capacitor to chassis ground |
Guia de Configuração de Pinos do KSZ8795CLXCC 10 mm x 10 mm
Configuração de pinos para KSZ8795CLXCC (pacote 10 mm x 10 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para KSZ8795CLXCC.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
KSZ8795CLXCC é adequado para 6 aplicaçãos: Industrial Ethernet Gateway, IP Camera Network Interface, Building Automation Controller, Network Communications Equipment, Set-Top Box and Media Gateway, Industrial IoT Edge Controller.
Industrial Ethernet Gateway
The KSZ8795CLXCC fits an industrial gateway that must consolidate several slower copper devices while preserving a faster uplink to a controller or plant network. Its four 10/100 Mbps copper ports can connect sensors, controllers, or service interfaces, while the 10/100/1000 Mbps uplink provides higher-bandwidth backhaul. The available GMII, RGMII, MII, and RMII interfaces support different embedded-controller arrangements. Design review should confirm industrial temperature, power, clocking, isolation, and environmental requirements before production use.
Recomendado
IP Camera Network Interface
The KSZ8795CLXCC is suitable for an IP camera or imaging appliance that needs several local 10/100 Mbps links and a Gigabit connection to a network processor. Four copper ports can serve peripherals, service interfaces, or additional cameras, while the managed Layer 2 fabric provides controlled frame forwarding. The processor interface selection should be matched to the image processor's supported MII, RMII, GMII, or RGMII configuration. Magnetic-interface components, Ethernet magnetics, and connector-side termination must follow the manufacturer hardware checklist.
Recomendado
Building Automation Controller
The KSZ8795CLXCC can serve as the Ethernet switching element in a building-automation controller linking HVAC equipment, access-control units, sensors, and supervisory software. Four 10/100 Mbps ports support a practical mix of embedded Ethernet devices, while the Gigabit uplink handles traffic toward a building network. Managed Layer 2 operation is useful when the system needs controlled addressing and port behavior. Verify controller interface timing, system power architecture, isolation strategy, and environmental requirements before selecting the switch.
Recomendado
Network Communications Equipment
The KSZ8795CLXCC fits communications equipment that combines several 10/100 Mbps access connections with a Gigabit uplink to a host processor. A compact five-port switching function can reduce the number of discrete network interfaces required by an embedded access product. The choice among MII, RMII, GMII, and RGMII should follow the host processor's bus width, clocking, and signal-integrity requirements. Layout review should emphasize short processor traces, controlled return paths, and isolation from copper-port magnetics and connector circuitry.
Recomendado
Set-Top Box and Media Gateway
The KSZ8795CLXCC is applicable to media gateways, set-top products, and consumer network appliances requiring multiple copper access ports plus a faster uplink. Four 10/100 Mbps ports can serve local service connections, while the Gigabit uplink supports video or data transfer toward a home router or access network. The compact 80-lead LQFP helps integrate switching without a discrete multi-chip arrangement. Firmware must support the selected management functions, and the PCB must implement the manufacturer's port termination and layout recommendations.
Recomendado
Industrial IoT Edge Controller
The KSZ8795CLXCC can support an IoT edge controller that gathers traffic from multiple wired endpoints and forwards it through a Gigabit uplink. Four 10/100 Mbps ports provide a practical bridge among sensors, actuators, service tools, and local controllers, while managed Layer 2 behavior supports predictable network operation. The processor interface and clock requirements must align with the edge-compute SoC, and the board design must account for copper-port magnetics, chassis-ground references, thermal performance, and electromagnetic isolation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para KSZ8795CLXCC — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | KSZ8721BLI-TR | KSZ8081RNACA | TJA1057GTK/3Z |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | NXP Semiconductors |
| Device Category | Layer 2-managed Ethernet switch | Ethernet switch | Ethernet interface IC | Ethernet transceiver |
Principais diferenciais
- Combines multiple copper ports with a dedicated Gigabit uplink (vs KSZ8721BLI-TR)
- Supports both reduced-width and Gigabit processor interfaces (vs KSZ8081RNACA)
- Integrates switching and management rather than only a physical-layer transceiver (vs TJA1057GTK/3Z)
Notas de projeto
Use the Microchip KSZ8795CLX hardware design checklist as the PCB layout baseline. The manufacturer specifically identifies RJ45 pins 3 and 6 as the transmit pair for the KSZ8795CLX. On the cable side of the transmit channel, terminate the center tap through the specified 75 ohm resistor and 1000 pF, 2 kV capacitor to chassis ground. Keep copper-port routing away from processor-interface clocks and sensitive return paths, and review the complete recommended component network before release.
Assign the switch's supply rails and ground pins directly from the manufacturer pin-description and power-supply sections rather than inferring connectivity from a block diagram. The available product information does not state the operating voltage range, current limits, sequencing requirements, or decoupling values, so these must remain engineering hold points. Confirm startup behavior, controller interface power states, magnetic-device requirements, and exposed thermal-pad connection in the datasheet before schematic release.
Select GMII, RGMII, MII, or RMII according to the host processor's supported clocking and data-width arrangement; nominal functional similarity does not make the interfaces electrically interchangeable. Follow the manufacturer trace-length, impedance, decoupling, and clock-routing guidance for the selected interface. Because processor-interface timing and I/O specifications are not published in the product summary, validate them from the datasheet and use the hardware checklist during signal-integrity review.
Informações de conformidade
The product summary does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. These attributes must be confirmed from the manufacturer product declaration or ordering documentation.