KSZ8851-16MQLI - 10/100 Ethernet MAC Controller | Microchip
N.º da peça: KSZ8851-16MQLI ✓ AtivoKSZ8851-16MQLI Visão geral
An Ethernet MAC controller is a semiconductor that connects a processor or microcontroller to a physical Ethernet network. The MAC sublayer manages frame transmission, reception, addresses, and error detection, while the integrated PHY converts between digital Ethernet data and analog signals on the network. The KSZ8851 therefore places both functions in one device instead of requiring a separate Ethernet PHY and dedicated network controller.
The KSZ8851 family provides a generic 8-bit, 16-bit, or 32-bit non-PCI interface, plus SPI interface options in the wider product family. The -16MQLI configuration is supplied in a 128-pin PQFP and includes 18 KB of on-chip memory as listed for this exact orderable part. Operating from 3.3 V, the device is suited to embedded industrial control, building automation, networking equipment, test systems, and communication appliances that require 10/100 Ethernet without a PCI interface.
The 128-pin package exposes the parallel host bus, Ethernet physical-layer signals, clock and reset inputs, power connections, and interrupt signaling. Because the device combines a PHY and MAC, PCB implementation also requires careful separation of analog and digital return paths. The manufacturer's KSZ8851-16/32MQL datasheet describes the 8-bit and 16-bit generic processor interfaces used by this configuration and provides the authoritative reference for pin assignments, timing, and electrical limits.
Typical designs connect the parallel bus to an embedded processor, an RJ45 magnetic network interface, and a 3.3 V regulator. The Ethernet magnetics perform isolation and impedance matching, while the controller manages access to the network medium. Software drivers for the KSZ8851 are used with common embedded processors, including STM32-class systems, and interrupt-driven operation reduces the need for continuous host polling.
During schematic design, reserve the Ethernet differential pair for direct connection between the PHY and network magnetics, and avoid placing high-current digital return paths beneath the analog section. Follow the reference circuit and decoupling recommendations in the manufacturer datasheet for capacitors, crystals, reset sequencing, and analog supply connections.
This page combines the exact 128-pin orderable configuration with package, interface, application, and selection information designed to help engineers evaluate the KSZ8851-16MQLI against lower-pin-count KSZ8851 options before committing a PCB layout.
Alternativas drop-in para KSZ8851-16MQLI — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com KSZ8851-16MQLI (mesmo formato e footprint) — diferindo em Host Interface, Mounting Type, Product Type.
KSZ8851-16MQL
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
KSZ8851-16MQLI Especificações
| Product Type | Single-port Ethernet MAC controller with integrated PHY |
| Ethernet Standard Support | 10BASE-T and 100BASE-TX |
| Maximum Data Rate | 100 Mbit/s |
| Supported Data Rates | 10 Mbit/s and 100 Mbit/s |
| Host Interface | 8-bit or 16-bit generic parallel non-PCI interface |
| Tensão de alimentação | 3.3 V |
| On-Chip Memory | 18 KB |
| Number of Ports | 1 Ethernet port |
| Package Type | 128-pin PQFP |
| Package Dimensions | 14 x 20 mm |
| Tipo de montagem | Surface mount |
| RoHS Compliance | RoHS compliant |
| Manufacturer | Microchip Technology |
| Interface Classification | Ethernet controller, MAC, and PHY |
| Bus Interface Type | Generic 8-bit or 16-bit parallel bus |
Guia de Configuração de Pinos do KSZ8851-16MQLI 14 x 20 mm
Configuração de pinos para KSZ8851-16MQLI (pacote 14 x 20 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para KSZ8851-16MQLI.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
KSZ8851-16MQLI é adequado para 6 aplicaçãos: Embedded Industrial Control Terminals, Building Automation and HVAC Controllers, Embedded Linux and RTOS Network Nodes, Networked Test and Measurement Equipment, Communication Appliances and Gateways, Audio and Video Network Endpoints.
Embedded Industrial Control Terminals
The KSZ8851-16MQLI fits industrial control terminals that require 10/100 Ethernet for supervisory communication, configuration transfer, and remote diagnostics. Its integrated 10BASE-T and 100BASE-TX PHY removes the need for a separate Ethernet transceiver, while the generic 8-bit or 16-bit parallel interface connects efficiently to an embedded microcontroller. The 3.3 V device operates at both 10 Mbit/s and 100 Mbit/s. Place the Ethernet differential routing between the controller and network magnetics with continuous return paths, and verify the enclosure temperature requirement against the manufacturer datasheet before production release.
Recomendado
Building Automation and HVAC Controllers
The KSZ8851-16MQLI supports building automation controllers, HVAC gateways, and room-control units that communicate over an existing Fast Ethernet network. The 10BASE-T and 100BASE-TX functions support links from 10 Mbit/s up to 100 Mbit/s, allowing the controller to share network traffic with sensors, workstations, and supervisory systems. Its generic parallel host bus is suitable for processors without a PCI controller. The 128-pin PQFP provides the interface options required by the family, but designers should preserve the recommended analog and digital separation around the PHY and magnetics.
Recomendado
Embedded Linux and RTOS Network Nodes
The KSZ8851-16MQLI is appropriate for embedded Linux or RTOS nodes that require a dedicated Fast Ethernet front end and a processor-facing parallel bus. Existing KSZ8851 driver material provides a known integration path for processors such as STM32-class devices, including interrupt-driven packet handling. At 100 Mbit/s, the controller provides a practical throughput ceiling for supervisory data, web interfaces, logging, and firmware update traffic. Firmware must select the correct 8-bit or 16-bit interface mode, connect the interrupt signal to a processor GPIO, and follow the manufacturer's reset and clock recommendations.
Recomendado
Networked Test and Measurement Equipment
The KSZ8851-16MQLI can add remote control and data transfer to test equipment, analyzers, and laboratory instruments. The integrated 10/100 PHY consolidates the network interface, and the generic parallel bus allows a local processor or FPGA to exchange commands and results without a PCI interface. The controller supports 10 Mbit/s and 100 Mbit/s links, which suits instrument networks handling status updates, result files, and remote commands. Keep the Ethernet pair tightly controlled and isolated from high-energy switching nodes, and confirm grounding and isolation requirements for bench or permanently installed systems.
Recomendado
Communication Appliances and Gateways
The KSZ8851-16MQLI is well matched to protocol gateways, serial-to-Ethernet products, and communication appliances that bridge embedded equipment with an IP network. Its integrated PHY supports standard 10BASE-T and 100BASE-TX links, while the 8-bit or 16-bit host interface gives a processor direct access to the MAC service. The 128-pin PQFP package provides a practical option when routing space is sufficient and the host bus is parallel rather than SPI. Designers should use the manufacturer's reference network circuit, provide the specified decoupling, and keep the magnetics and RJ45 interface close to the PHY connections.
Recomendado
Audio and Video Network Endpoints
The KSZ8851-16MQLI can support networked audio, video, and control endpoints where a separate host manages media while Ethernet provides synchronization, control, or configuration traffic. The 100 Mbit/s maximum rate is appropriate for supervisory links and moderate control traffic, rather than uncompressed multi-stream video transport. The controller's parallel host bus can move packets efficiently into a processor-managed buffer, and the integrated PHY reduces the external network component count. Use interrupt-driven reception for latency-sensitive control packets and validate the complete interface timing against the manufacturer's DS00002425B datasheet.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para KSZ8851-16MQLI — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | KSZ8851-16MQL |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 128-pin PQFP (14 x 20 mm) | 128-pin PQFP (14 x 20 mm) |
| Ethernet Speed Support | 10 Mbit/s and 100 Mbit/s | 10 Mbit/s and 100 Mbit/s |
| Physical Layer | Integrated 10BASE-T and 100BASE-TX PHY | Integrated 10BASE-T and 100BASE-TX PHY |
| Host Interface | 8-bit or 16-bit generic parallel non-PCI | 8-bit or 16-bit generic parallel non-PCI |
| Supply Voltage | 3.3 V | 3.3 V |
| On-Chip Memory | 18 KB | 18 KB |
| Port Count | 1 Ethernet port | 1 Ethernet port |
Principais diferenciais
- Higher pin count provides a larger 128-pin interface implementation (vs KSZ8851-16MLL)
- Integrated 10/100 PHY reduces external network component count (vs KSZ8851-16MQL)
- Parallel host bus suits processors without PCI support (vs KSZ8851-16MQL)
Notas de projeto
Route the Ethernet differential pair as a continuous, controlled-impedance connection between the KSZ8851-16MQLI and the network magnetics. Do not split the ground or power plane beneath the pair, and keep high-current switching paths away from the PHY section. Follow the component placement and reference network circuit in datasheet DS00002425B, and use the shortest practical path from the controller to the magnetics.
Decouple the 3.3 V supply at the controller with the capacitance and placement specified by the manufacturer reference circuit. Separate noisy digital return paths from the Ethernet PHY return connections wherever the layout permits. Review the datasheet for all supply pins, analog and digital supply requirements, and power-up sequencing before assigning the printed-board power network.
Do not substitute a 48-pin KSZ8851 member for this 128-pin device on an existing board. Although the controller family supports similar Ethernet functions, the smaller KSZ8851-16MLL uses a different footprint and pin arrangement. Also configure the firmware for the physical 8-bit or 16-bit host-bus mode actually used on the PCB, because an incorrect bus-width setting prevents normal controller operation.
Informações de conformidade
RoHS compliance is stated for this exact orderable part. REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification statements require confirmation from the manufacturer or an authorized compliance document.