Microchip Technology

LAN8710A-EZC-TR-ABC - 10/100 Ethernet PHY | Microchip

N.º da peça: LAN8710A-EZC-TR-ABC ✓ Ativo
1.6 V to 3.6 V Vdss IEEE 802.3u Rds(on) 32-VFQFN with exposed pad Package
MOQ: 1 |

LAN8710A-EZC-TR-ABC Visão geral

The Microchip LAN8710A-EZC-TR-ABC is a low-power 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with a 32-pin VFQFN exposed-pad package. It supports 10 Mbps and 100 Mbps data rates, full-duplex operation, IEEE 802.3u MII, and RMII connections to an Ethernet media-access controller. The device operates from a 1.6 V to 3.6 V supply and is specified for the extended commercial temperature range of 0°C to 85°C.

An Ethernet PHY is the physical-layer component that converts digital MAC data into differential signals for a twisted-pair cable, then converts received signals back into digital data. The LAN8710A occupies the PHY layer of the Ethernet hierarchy, above the physical medium and below the MAC layer. Its integrated 10/100 capability allows one Ethernet port design to support both legacy 10 Mbps networks and Fast Ethernet networks operating at 100 Mbps.

Microchip LAN8710A devices feature HP Auto-MDIX, which allows a single RJ45 port to work with straight-through or crossover cables. Automatic negotiation selects the best supported speed and duplex mode, while the transceiver also provides full-duplex operation for contemporary switched Ethernet links. These functions simplify installation and reduce the need for manual link configuration in consumer, industrial, and enterprise equipment.

The flexPWR technology used in the LAN8710A family supports low-power operation and is intended for compact, energy-conscious designs. The MII interface supports both 10 Mbps and 100 Mbps transfer rates, while RMII reduces the number of MAC interface signals where a reduced-pin architecture is desirable. The exposed thermal pad beneath the 5 mm by 5 mm package provides a direct heat-dissipation path to the PCB copper during continuous data transmission.

Typical uses include industrial Ethernet controllers, embedded Linux platforms, network appliances, set-top equipment, printers, IP cameras, and compact communication modules. A MAC such as a Microchip STM32 controller can connect over RMII when its integrated Ethernet MAC supports the required clock and data signaling, while a more complex processor may use the full MII interface.

For PCB design, reserve the exposed pad as a thermal and ground connection, follow the manufacturer's recommended magnetics and decoupling network, and keep the high-speed differential pairs short, symmetric, and continuously referenced to the ground plane. Confirm the exact pin functions, strap resistors, reference clock method, and RMII timing configuration in the LAN8710A datasheet before releasing the PCB layout.

Alternativas drop-in para LAN8710A-EZC-TR-ABC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com LAN8710A-EZC-TR-ABC (mesmo formato e footprint) — diferindo em Package, MAC Interface, RoHS Status, Cable Support, Package Dimensions.

Microchip Technology
Package: 32-QFN
Cable Support: Direct-connect or crossover LAN cables
Package Dimensions: 5 x 5 mm
Comparar com LAN8710A-EZC-TR-ABC →
Microchip Technology
Package: 32-QFN, 5 x 5 mm
RoHS Status: Compliant
Comparar com LAN8710A-EZC-TR-ABC →
Microchip Technology
Package: 32-SQFN, 5x5 mm
MAC Interface: MII or RMII digital interface
RoHS Status: Compliant
Comparar com LAN8710A-EZC-TR-ABC →

LAN8710A-EZC-TR

✅ Drop-In ⚠️ Especificações não verificadas
Microchip Technology
📦 32-VFQFN (5x5)
10BASE-T and 100BASE-TX · 10 Mbps and 100 Mbps · Full-duplex · MII and RMII · IEEE 802.3u · Supported · HP Auto-MDIX supported · Direct-connect or crossover LAN cables

Consulte o preço

Ver ficha técnica →

LAN8710A-EZC-ABC

✅ Drop-In
Microchip Technology
📦 32-VFQFN (5x5)
10/100 Ethernet physical-layer transceiver · 10 Mbps and 100 Mbps · 10BASE-T and 100BASE-TX · MII or RMII · 4/4 transceiver · Supported · Supported · Microchip flexPWR technology

Consulte o preço

Ver ficha técnica →

LAN8710AI-EZK-ABC

✅ Drop-In
Microchip Technology
📦 32-VFQFN (5x5)
10BASE-T and 100BASE-TX · 100 Mbit/s · MII or RMII digital interface · Variable I/O voltage · HP Auto-MDIX · Automatic negotiation · IEEE 802.3-2005 · flexPWR technology

Consulte o preço

Ver ficha técnica →

LAN8710AI-EZK-TR

✅ Drop-In
Microchip Technology
📦 32-VFQFN (5x5)
10/100 Ethernet PHY transceiver · 10 Mbps and 100 Mbps · IEEE 802.3-2005 · MII and RMII · 1 channel · 10BASE-T and 100BASE-TX · Supported · HP Auto-MDIX supported

Consulte o preço

Ver ficha técnica →

LAN8710AI-EZK-TR-ABC

✅ Drop-In
Microchip Technology
📦 32-VFQFN (5x5)
10BASE-T/100BASE-TX Ethernet physical-layer transceiver · 10 Mb/s and 100 Mb/s · MII or RMII digital interface · 32-SQFN, 5x5 mm · Surface mount · -40°C to 85°C · 10BASE-T and 100BASE-TX · Supported

Consulte o preço

Ver ficha técnica →

LAN8710A-EZC-TR-ABC Especificações

Ethernet Data Rates 10 Mbps and 100 Mbps
Supported Standards IEEE 802.3u
MAC Interface MII and RMII
Operating Modes 10BASE-T and 100BASE-TX, full-duplex
Supply Voltage Range 1.6 V to 3.6 V
Number of Drivers/Receivers 4/4
Temperatura de operação 0°C to 85°C
Package Type 32-VFQFN with exposed pad
Package Dimensions 5 mm x 5 mm x 0.9 mm
Tipo de montagem Surface mount
Packaging Tape and reel
Product Status Active
Status RoHS ROHS3 compliant
Auto-MDIX Support HP Auto-MDIX
Link Negotiation Automatic speed and duplex negotiation
Power Technology Microchip flexPWR
Manufacturer Lead Time 4 weeks

Guia de Configuração de Pinos do LAN8710A-EZC-TR-ABC 5 mm x 5 mm x 0.9 mm

Configuração de pinos para LAN8710A-EZC-TR-ABC (pacote 5 mm x 5 mm x 0.9 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 5 mm x 5 mm x 0.9 mm para LAN8710A-EZC-TR-ABC

Nenhum dado detalhado de pinagem disponível para LAN8710A-EZC-TR-ABC.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

LAN8710A-EZC-TR-ABC é adequado para 6 aplicaçãos: Industrial Embedded Ethernet Controller, Compact Network Appliance, IP Camera and Security Equipment, ESP32-Based Connected Product, Printer and Networked Peripherals, Set-Top and Connected Consumer Equipment.

🏭

Industrial Embedded Ethernet Controller

The LAN8710A-EZC-TR-ABC fits industrial embedded controllers that need a compact 10/100 Ethernet endpoint with a short MAC-to-PHY interface. Its MII and RMII support allows the PCB to accommodate different MAC architectures, while 1.6 V to 3.6 V operation suits mixed 1.8 V, 2.5 V, and 3.3 V systems. The 5 mm by 5 mm VFQFN outline keeps the PHY area compact, and HP Auto-MDIX removes the need for a manually configured crossover link. In an industrial enclosure, provide thermal copper under the exposed pad and isolate the magnetics and cable connector from noisy power stages.

🌐

Compact Network Appliance

A single LAN8710A-EZC-TR-ABC supports both 10BASE-T and 100BASE-TX links, making it suitable for compact gateways, controllers, and network appliances with legacy 10 Mbps fallback. Automatic negotiation selects the supported speed and duplex mode without user intervention, while HP Auto-MDIX allows either straight-through or crossover patch cables. The PHY occupies a 32-VFQFN footprint, reducing routing congestion around the transformer and RJ45 connector. Use the RMII interface when the controller supports it, and verify the reference-clock and strap requirements in the manufacturer datasheet.

🎥

IP Camera and Security Equipment

The LAN8710A-EZC-TR-ABC can provide the copper-Ethernet physical layer in an IP camera or compact surveillance product while the system processor handles video and network protocol processing. Automatic negotiation preserves interoperability with both 10 Mbps and 100 Mbps switches, and HP Auto-MDIX improves installation reliability. The 5 mm by 5 mm package leaves more board space for the image sensor interface and storage. A controlled reference clock, clean PHY supply, and properly terminated magnetics are essential for reliable video streaming across temperature changes and cable lengths specified by IEEE 802.3u.

🧩

ESP32-Based Connected Product

The LAN8710A-EZC-TR-ABC can add wired Ethernet to an ESP32-based product when the selected ESP32 variant exposes a compatible Ethernet MAC with RMII signaling. The PHY handles 10BASE-T and 100BASE-TX encoding, decoding, and auto-negotiation while the ESP32 manages the MAC and application protocol. The 1.6 V to 3.6 V PHY supply range supports common embedded rails, but the RMII signal levels, reference-clock source, and 50 MHz timing requirements must match the controller. Keep the RMII traces short and confirm the complete interface implementation against the LAN8710A datasheet.

🖥️

Printer and Networked Peripherals

The LAN8710A-EZC-TR-ABC suits network-enabled printers, scanners, and office peripherals that need a compact 10/100 port with broad switch compatibility. Supporting both 10 Mbps and 100 Mbps allows the same product to work on older networks while taking advantage of Fast Ethernet links where available. Automatic negotiation removes configuration complexity for users, and HP Auto-MDIX accepts either cable type. The exposed-pad VFQFN package supports dense board layouts, but the design must keep PHY supply noise away from sensitive signal paths and follow the manufacturer's recommended component placement around the transformer.

📺

Set-Top and Connected Consumer Equipment

The LAN8710A-EZC-TR-ABC provides a cost-conscious wired-network path for set-top boxes, media adapters, and connected consumer products that also use wireless links. Its small footprint and low-power flexPWR design suit space-constrained boards, while MII and RMII support gives designers flexibility in the choice of host controller. Automatic speed negotiation and HP Auto-MDIX improve end-user setup reliability. The component is specified for 0°C to 85°C, making it appropriate for indoor consumer products. For thermally variable environments, verify the complete system temperature budget and use an industrial-grade ordering option when required.

What is the LAN8710A-EZC-TR-ABC?
The LAN8710A-EZC-TR-ABC is a Microchip 10/100 Ethernet physical-layer transceiver that connects an Ethernet MAC to a 10BASE-T or 100BASE-TX twisted-pair network. According to the Microchip LAN8710A datasheet, it supports IEEE 802.3u MII and RMII interfaces, automatic speed and duplex negotiation, and HP Auto-MDIX in a 32-VFQFN package.
What are the key specifications of LAN8710A-EZC-TR-ABC that engineers should know?
The LAN8710A-EZC-TR-ABC supports 10 Mbps and 100 Mbps Ethernet, operates from 1.6 V to 3.6 V, and is specified from 0°C to 85°C. The Microchip datasheet also identifies MII and RMII MAC interfaces, HP Auto-MDIX, automatic negotiation, 4/4 drivers and receivers, and a 5 mm by 5 mm VFQFN package with an exposed pad.
Where can I download the LAN8710A-EZC-TR-ABC datasheet PDF?
The official LAN8710A datasheet PDF is available from Microchip at the product data sheet link listed on this page. It covers the MII and RMII interfaces, supported 10BASE-T and 100BASE-TX modes, HP Auto-MDIX, flexPWR operation, electrical characteristics, package information, and the recommended application circuit. Use the manufacturer document when assigning pins and designing the external magnetics network.
Where can I find the LAN8710A-EZC-TR-ABC pinout?
The authoritative pinout appears in the pin-description table and package drawing of the Microchip LAN8710A datasheet. The device uses a 32-VFQFN package with an exposed pad, so the exposed pad must be accounted for separately from the 32 numbered terminals. Use that document to confirm signals such as the reference clock, power rails, RMII or MII data, and configuration straps.
What is the difference between MII and RMII on the LAN8710A-EZC-TR-ABC?
MII provides separate control and data signals for 10 Mbps and 100 Mbps operation, while RMII uses a reduced signal set intended for 100 Mbps designs. According to the Microchip LAN8710A datasheet, the transceiver supports both interfaces. The choice depends on the connected MAC, clock arrangement, board space, and the timing requirements of the specific controller.
Does the LAN8710A-EZC-TR-ABC support both 10 Mbps and 100 Mbps networks?
Yes, the LAN8710A-EZC-TR-ABC supports both 10BASE-T at 10 Mbps and 100BASE-TX at 100 Mbps. The Microchip datasheet states that the integrated transceiver performs automatic negotiation to select the best available speed and duplex mode. This makes the device suitable for dual-speed 10/100 Ethernet ports used in embedded and industrial products.
What does HP Auto-MDIX mean for the LAN8710A-EZC-TR-ABC?
HP Auto-MDIX allows the LAN8710A-EZC-TR-ABC to work with straight-through or crossover Ethernet cables without a manual MDI/MDIX setting. The Microchip datasheet identifies HP Auto-MDIX as a supported feature. This simplifies installation in consumer and industrial networks where users may connect either cable type to the same RJ45 port.
Is the LAN8710A-EZC-TR-ABC suitable for an ESP32-based design?
The LAN8710A-EZC-TR-ABC can be used with an ESP32 only when the controller includes a compatible Ethernet MAC interface and the board can meet the required RMII or MII timing. The Microchip device provides the 10/100 PHY layer, while the ESP32 must provide the MAC layer. Confirm the controller's pin multiplexing, reference-clock source, and 1.8 V or 2.5 V interface requirements before layout.
What is the best drop-in replacement for LAN8710A-EZC-TR-ABC?
The closest same-family replacement is the LAN8710A-EZC-TR, which retains the 32-QFN package and 10/100 MII-RMII Ethernet function while changing the temperature grade of the ordering code. The FindIC comparison describes the terminals and package as consistent. A true drop-in decision still requires checking the temperature range and any configuration differences against your schematic.
Can LAN8710A-EZC-ABC replace LAN8710A-EZC-TR-ABC?
The LAN8710A-EZC-ABC can serve as an electrical and pin-compatible replacement when the difference in delivery format is acceptable. The FindIC comparison states that the terminals, package, and principal performance characteristics are consistent. The ABC ordering code is tray-packed, while the target TR code is tape-and-reel packed, and the commercial temperature grade should also be checked.
When should I choose LAN8710A-EZC-TR-ABC instead of another Ethernet PHY?
Choose the LAN8710A-EZC-TR-ABC when the design needs a compact 10/100 PHY with both MII and RMII options, automatic negotiation, and HP Auto-MDIX in a 5 mm by 5 mm VFQFN package. According to the Microchip datasheet, it is intended for low-power consumer, industrial, and enterprise equipment. Alternatives should be chosen only when their pinout, clock method, voltage, and thermal ratings match the PCB.
Is the LAN8710A-EZC-TR-ABC an industrial-temperature Ethernet PHY?
The LAN8710A-EZC-TR-ABC is specified for 0°C to 85°C and is therefore an extended commercial temperature option rather than the -40°C to 85°C industrial option. Microchip's product page identifies both extended commercial and industrial LAN8710A variants. For installations with significant temperature excursions, select the ordering code that explicitly carries the industrial temperature rating.
What is the supply voltage range of LAN8710A-EZC-TR-ABC?
The LAN8710A-EZC-TR-ABC operates from 1.6 V to 3.6 V, according to the Microchip product information. This range supports low-voltage digital designs while accommodating common 2.5 V and 3.3 V system rails. The exact rail used for the transceiver core and the I/O voltage relationship should be verified in the manufacturer application and electrical-characteristics sections.
Where can I buy LAN8710A-EZC-TR-ABC online?
Use the Request a Quote form on this page to request LAN8710A-EZC-TR-ABC pricing, current inventory, and shipment scheduling. Microchip lists the device as active with a stated manufacturer lead time of four weeks, and the product is also offered in tape-and-reel packaging. Quote requests allow the exact ordering code, quantity, and delivery requirements to be confirmed together.
How long is the lead time for LAN8710A-EZC-TR-ABC?
The stated Microchip manufacturer lead time for LAN8710A-EZC-TR-ABC is four weeks. Microchip also lists the part as active and available in full tape-and-reel quantities. Use the Request a Quote form on this page to confirm the current lead time and stock allocation for your required quantity rather than relying on a historical schedule.

Dados de referência de engenharia para LAN8710A-EZC-TR-ABC — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the LAN8710A-EZC-TR-ABC for a compact 10/100 Ethernet port that needs MII or RMII, automatic negotiation, HP Auto-MDIX, and extended-commercial temperature operation. The tape-and-reel format also suits automated assembly. Choose LAN8710A-EZC-ABC when the same electrical configuration is needed but tray packaging is more convenient. Select LAN8710A-EZC-TR or a LAN8710AI ordering option when the enclosure requires an industrial temperature rating, after verifying clock, strap, and interface details. For designs needing more than one Ethernet port, higher multi-gigabit performance, integrated switching, or USB networking, use a dedicated multi-port Ethernet controller instead of forcing this single-port PHY into a different architecture.

Comparação com alternativas

Parâmetro Este produto LAN8710A-EZC-TR LAN8710A-EZC-ABC LAN8710AI-EZK-ABC LAN8710AI-EZK-TR LAN8710AI-EZK-TR-ABC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 32-VFQFN (5x5) 32-VFQFN (5x5) 32-VFQFN (5x5) 32-VFQFN (5x5) 32-VFQFN (5x5) 32-VFQFN (5x5)
Ethernet Data Rates 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps
Operating Temperature 0°C to 85°C -40°C to 85°C 0°C to 85°C -40°C to 85°C -40°C to 85°C -40°C to 85°C
Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX
Delivery Format Tape and reel Tape and reel Tray Tray Tape and reel Tape and reel
Low-Power Technology flexPWR flexPWR flexPWR flexPWR flexPWR flexPWR

Principais diferenciais

  • Combines 10/100 support with both MII and RMII in one compact PHY (vs LAN8710AI-EZK-TR)
  • Extensive compatibility with standard 10/100 network infrastructure (vs LAN8710A-EZC-TR)
  • Tape-and-reel configuration supports automated production assembly (vs LAN8710A-EZC-ABC)
  • Low-power design aligned with compact embedded systems (vs LAN8710AI-EZK-TR-ABC)

Notas de projeto

Place the PHY close to the RJ45 connector and integrated magnetics, and keep the differential pairs short, symmetric, and continuously referenced to an uninterrupted ground plane. Avoid placing the PHY clock source, switching regulators, and magnetic components directly beneath the network interface. Follow the pinout and layout guidance in the Microchip LAN8710A datasheet, including the treatment of the exposed pad and configuration straps.

Separate the PHY supply routing from noisy digital and switching-supply paths, and place the manufacturer-recommended bypass capacitors immediately beside the relevant power pins. The 1.6 V to 3.6 V operating range does not remove the need for local filtering: supply noise can affect clock jitter, RMII timing, and link stability. Validate the rail with an oscilloscope at the PHY pins under maximum traffic and during simultaneous MAC transmission.

The VFQFN exposed pad is the primary heat-dissipation path. Connect it to a solid ground plane with multiple vias and avoid thermally isolating the pad with narrow copper necks. For continuous 100 Mbps operation, check junction temperature against the lowest ambient temperature permitted by the completed product. Use the Microchip electrical data and package thermal information to determine whether additional copper area or a thermal via array is required.

Confirm the reference-clock source, reset behavior, strap-resistor values, and whether the host MAC requires RMII or MII before assigning the PCB pins. A clock-source or strap mismatch can prevent enumeration even when the PHY powers up correctly. Also confirm that the chosen alternative ordering code preserves the same pin configuration and temperature grade; package equality alone does not establish drop-in compatibility.

Informações de conformidade

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The Microchip product information identifies the LAN8710A-EZC-TR-ABC as ROHS3 compliant. The target is an active extended-commercial Ethernet PHY and is not identified as an automotive-qualified AEC-Q100 device.

Buscas relacionadas

lan8710a datasheet lan8710a ezc lan8710a ezc tr lan8710a ezc abc lan8710a ezc qfn32 lan8710a ezc datasheet lan8710a reference schematic lan8710a esp32 LAN8710A-EZC-TR-ABC pinout LAN8710A-EZC-TR-ABC replacement LAN8710A-EZC-TR-ABC QFN32 LAN8710A-EZC-TR-ABC price Microchip LAN8710A-EZC-TR-ABC LAN8710A-EZC-TR-ABC vs LAN8710A-EZC-TR

Componentes & termos relacionados

Microchip Technology LAN8710A-EZC-TR-ABC LAN8710A LAN8710Ai Ethernet PHY physical-layer transceiver 10BASE-T 100BASE-TX IEEE 802.3u MII RMII HP Auto-MDIX flexPWR 32-VFQFN QFN family surface mount SMD Ethernet media-access controller RJ45 connector Ethernet magnetics automatic negotiation reference clock RoHS3 consumer electronics industrial networking
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ